Search Documents

By T. A. Sullivan

The Bureau of Mines investigated modified sulfur concretes as one part of a program for utilizing sulfur in construction materials. The use of modified sulfur was studied as a means of preventing the stressing action in the concretes caused by the allotropic transformation of sulfur on solidification. Unmodified sulfur concretes have been prepared that have compression, flexural, and tensile strengths equivalent or better than Portland concretes. However, most of these concretes have been vulnerable to deterioration by weathering, temperature fluctuations, and freeze-thaw cycling. The sulfur was modified by reaction with dicyclopentadiene or dipentene before use as an aggregate binder. Sulfur concretes and modified sulfur concretes were pre-pared from acidic and basic type aggregates. Physical properties of the optimum mixtures were determined and compared with each other and with Portland cement concretes. The best results were obtained by reacting sulfur with 5 pct dicyclopentadiene to prepare modified sulfur concretes. Field testing of the concretes are in progress. Present results show that modified sulfur concretes are superior to unmodified sulfur concretes and equal or better than Portland concretes in compressive, flexural, and tensile strengths. Long-term aging characteristics of both modified and unmodified sulfur concretes are being determined.

Jan 1, 1976

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill and blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill und blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By Ernest A. Curth

A 3-month study in 1971 of the Essen Roof Support and Rock Mechanics Research Center's program of roof and support evaluation included 25 mine trips. German miners must adopt mining methods and environmental control measures involving methane drainage and water infusion to improve productivity under severe natural conditions. Pressing problems in ground control must be solved such as cavities in front and above the supports at longwall faces and excessive convergence in gate roads. The Center developed automatic data processing methods to quantify the results of roof and support surveys and to establish criteria. Another approach to ground control is the study of mine models. The Center's laboratory has the facilities to test elements of powered roof support and whole assembled units. Face automation and roof control by powered shields are novel developments that are under close scrutiny in the field as well as in the laboratory. Though the Essen Center's roof and support evaluation techniques are tailored to the needs of the coal mining industry of the Federal Republic of Germany under conditions vastly different from those in the United States, some application may be found here, for instance, monitoring faces and roadways and preventive maintenance of hydraulic systems.

Jan 1, 1974

By John K. Alley, Robert C. Johnson

The primary objective of the research was to grow aluminum borate whiskers or fibers and to determine their properties . Molten salt bath and vapor deposition methods were used for synthesis . Whiskers exceeding 25 mm in length were grown . The best results were obtained by vapor deposition and most of the data presented were determined on whiskers produced by this method of synthesis . Three different aluminum borate compositions ( 4.8A1203 B₂03 , 3.8A1203 B203 , and 2.5A120, B203 ) were identified by X- ray and chemical analyses . The aluminum borates 4.8A1203 B20, X- ray diffraction pattern was indexed . Optical data were obtained on the three aluminum borates . In addition the following whisker properties and growth factors were determined : ideal atmospheric dewpoint for vapor deposition method , near 65 ° F ; temperature range of whisker formation , 1,000 ° to 1,400 ° C for the molten bath method of synthesis , > 1,000 ° to < 1,400 ° C for the vapor deposition method ; whisker growth rates by the vapor deposition method , maximum 12 mm per hour ; raw material vaporization , 50 to 60 percent of the fluoride lost in 1 hour ; tensile strength , maximum obtained 174,162 psi ; melting points , ranged from 1,675 ° to 1,795 ° C.

Jan 1, 1965

By Richard N. Spencer

Electric-furnace smelting for simultaneous recovery of zinc spelter and lead bullion from complex lead-zinc sinter was investigated. Reduction of lead and zinc was satisfactory. Condensation of lead and zinc vapor to pyrophoric metal powder in a water-cooled, shock-condensing system produced excellent recoveries. Metal-splash condensation to produce zinc spelter was unsatisfactory. Special smelting experiments differentiated the effects of several smelting parameters on zinc metal recovery. The principal cause for unsatisfactory zinc metal recovery was transfer of iron to the condenser and subsequent degradation of zinc in a mixture composed of lead and an iron-zinc intermetallic compound. Limitations of the process were determined. Slag-resistance open-bath electric smelting of complex lead-zinc sinter is not considered feasible.

Jan 1, 1967

By W. F. Watts

This report describes a statistical analysis of 41,502 respirable quartz dust samples collected from 1974 through 1981 in metal and nonmetal mines and mills. The goal of this Bureau of Mines study was to identify commodities and occupations associated with high quartz dust exposure so that future enforcement and research activity can be focused on the high-exposure areas. For this analysis, the Bureau used its computerized Mine Inspection Data Analysis System (MIDAS), which contains data on nearly 350,000 air samples, including data for 61 contaminants in 45 commodities. The samples analyzed were collected by inspectors of the Mine Safety and Health Administration (MS HA). The data were entered into the MIDAS computer and coded according to commodity, occupation, location, and other categorical information. Occupations an. commodities with high quartz dust exposure were identified by grouping the data by code categories. Workers at sandstone, clay and shale, and miscellaneous nonmetallic mineral mills had the highest quartz dust exposures. Within these mills, occupations with high exposures were baggers, general laborers, and persons involved in crushing, grinding, and sizing operations. Dust concentrations in these mills were not necessarily the highest, but because the dust contained a high percentage of quartz, the health risk from dust exposure was the greatest.

Jan 1, 1984

By Raymond O. Dannenberg

The gas-combustion retort developed by the Federal Bureau of Mines at the Rifle Oil Shale Project near Rifle, Colo., is a continuous, gravity-feed retort. The heat required to convert the kerogen in the oil shale to liquid oil is generated by the combustion of product gas and carbonaceous residue remaining on the retorted shale after the kerogen has been converted to oil, gas, and residue. A study of the effects of the process variables on retort operation, product yields, and product properties is important to the successful solution of the problems encountered in the development of a satisfactory process. Statistical methods were used to design the experiments and analyze the effects of the rate of shale throughput, the composition of dilution gas, the height of the shale bed above the air entry, air-gas distributor design, shale size range, and the ratios of the flow rates of the various gas streams entering the retort to the rate of shale throughput.

Jan 1, 1960

By W. H. Emens

[This circular is one of a series dealing with tie development and equip¬ment of small and medium size mines, and with the costs of such work prior to productive operation. The preparation and publication of these papers by the Bureau off Mines has been made possible through the cooperation of various min¬ing and development companies. The bureau of Mines has published a series of circulars dealing with min¬ing methods and costs at a large number of producing nines in the United States, Canada, Mexico, an, other countries. Unit costs of development work, shaft sinking, (rifting, crosscutting, tunneling, and raising are usually much higher in the preliminary development of a property than during its productive life.]

Jan 1, 1933

By James L. Elder

The Bureau of Mines and the Alabama. Power Co. jointly conducted a first experiment in underground gasification of coal at Gorgas, Ala., during the fall and winter of 1946-47. This preliminary experiment showed that it was not difficult to maintain combustion of coal underground, and that coal in place could be completely gasified. It was noted that the high temperature developed by the gasification of coal in place brought about changes in overlying strata that appeared to be favorable to the process. The high temperatures caused the roof rock to become plastic, to expand, and to settle down on the mine floor directly behind the reacting coke face. These results were promising enough to warrant further investigation of the process. It was believed that if this action could be controlled properly with roofs of similar composition, it would tend to force the gas-making fluids underground against the coal faces. Plans for the second experiment were based in part on this favor-able roof action, and the successful operation of the planned initial straightline passages depended on this fact. Gorgas was chosen as the site for the second experiment for the following reasons: A tract of coal land of sufficient size was available and isolated from the main body of coal; the roof rock was similar in composition to that encountered in the first experiment; and the overlying strata were thick enough to eliminate some of the operating difficulties that had been encountered, In addition, power, water, and machine-shop facilities as well as an adequate supply of labor were available in this area, and the friendly cooperation of the Alabama Power Co. further recommended this site for the planned experiment.

Jan 1, 1951

By Thomas S. Jones

This report discusses processing and use of the principal forms of manganese. The focus is on trends in the United States in the 20th century and specifics of domestic manganese material flows as of about 1990. To protect proprietary data, quantitative assessments are limited to the iron and steel industry, which accounts for about 90% of consumption. Nonmetallurgical uses are considered qualitatively. Approximate disposition of a U.S. cumulative consumption during 1901-90 of an estimated 69 million st of manganese is estimated to be iron and steel slag, 69%; nonmetallurgical uses of a dissipative na¬ture, 10%; iron and steel scrap, 9%; National Defense Stockpile, 3%; unidentified and/or including items in service, 10%. In slag from iron blast furnaces and steelmaking, manganese is present as a minor, relatively im¬mobile component, which so far has been uneconomical to recover. Construction and road building are main applications for these slags. Steel slag contains the greater amount of manganese. Studies by others of global manganese fluxes and the effect of human activities on them also are discussed. One source concludes that the main effect of human activities, via deforestation and agricultural activities, has been to increase the rate of transport of manganese to the oceans.

Jan 1, 1994

By Joseph A. Hrabik

The Bureau of Mines compared the feasibility of mining deep phosphate deposits by a borehole mining system with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 150 ft or greater; however, at 50- and 100-ft thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasiblity of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is employed to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1983

By R. R. Hornor, Harry E. Tufft

The purpose of this bulletin is to point out some of the benefits and economies to be derived by selecting, preparing, storing, preserving, and utilizing mine timber more carefully and to give some specific information on certain preservatives and processes suitable for mine timber.

Jan 1, 1925

By D. Randolph Berry

Foster-Miller Associates has developed a set of guidelines to permit hoist manufacturers, mine owners, and MESA mine inspectors to design, purchase, install or inspect a safe and effective Emergency Escape Hoist, as required by the Coal Mine Health and Safety act of 1969. A series of surveys were carried out to determine: 1. The attitudes and local needs of the MESA District Managers. 2. Current escape hoist installations. 3. Equipment available for future designs. 4. Foreign methods and equipment for mine rescue. From these survey studies, preliminary guideline objectives were developed.

Jan 1, 2012

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and, liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise eight be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and. removing the disintegrated clay particles from wells after the perforated pipes have been inserted. Mechanical methods for removing mud sheaths are quite satisfactory, but prompted by tie request of certain operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions.

Jan 1, 1934

By C. C. Stevenson, Thomas Varley, E. P. Barrett, ROBERT H. BRADFORD

The art of treating ores by the chloride volatilization process is still in the experimental stage. The process has not been sufficiently developed along metallurgical lines to warrant a definite statement as to the exact place it will occupy in the industry. The basic theory of the process has received the attention of prominent metallurgists for 20 years, and considerable research and experimental work have been carried on. Much of the experimental work done has never been published; if the accumulated results were made known, they would greatly aid,. the further development of the process. This bulletin aim~ to bring the salient features of the process to the attention of metallurgists for the purpose of furnishing information to and receiving comments from interested parties with the ultimate hope that the process will be a commercial success. If commercially utilized, the process will fill a long-felt want in metallurgy, especially in the treatment of oxidized and semioxidized or" carbonate" ores of copper, lead, and silver. Such ores are difficult to treat by gravity concentration or by flotation: in the former their tendency to slime upon crushing and their being of lower specific gravity than the sulphide minerals cause serious losses; in the latter much has been done in sulphidizing oxidized ores and subsequently recovering the artificial sulphides by flotation. Difficulties in proper sulphidizing and the low recoveries obtained have not balanced the cost of the treatment in many plants and in very few has it proved successful. Evidently there is a big void to fill in the treatment of these ores. No radical changes in present methods are forecast, but it is obvious that chloride volatilization can have a distinct place as a method of treatment for ores that are not readily amenable to present methods. In many plants it might replace concentration methods, especially where part of the mineral content in the ores exists in forms other than sulphides.

Jan 1, 1923

By R. S. Dean

Boron compounds have been considered for many years as possible additions to iron and steel. A very recent use of boron-steel rods was for the control of neutron intensity in the graphite-uranium pile at the Clinton plutonium plant(130).4/ Norris(129) reports that slags containing boric oxide reduce the ferrous oxide content of steels and thereby the aluminum required for deoxidation. Boron is not considered an alloying element, but minute amounts produce what is often called a "needled" steel. The study of a series of iron-boron alloys by convenient steps, starting with iron containing no boron, indicated that boron was a hardening agent and made the iron very difficult if not impossible to forge. Then came the discovery that very minute traces of boron are quite different from the smallest amount previously thought worthy of study.

Jan 1, 1946

By Benjamin W. Haynes

The Bureau of Mines conducted research to provide technical information needed to devise waste management plans for the processing of manganese nodules. Studies included summary descriptions of Pacific manganese nodules, process options and flowsheets, methods for characterizing nodules and their tailings, and results of analyses of laboratory and pilot-plant generated tailings. This information is the result of a cooperative research effort of the Bureau of Mines and the National Oceanic and Atmospheric Administration (NOAA), with NOAA providing funding and the Bureau conducting the research. A summary of the extensive literature review is provided for manganese nodule mineralogy, chemistry, processing techniques, and methods of analyses. Characterizations and analyses of laboratory-generated tailings and slags are given, as well as the results of the leaching studies on these waste materials. Leachability was determined by three standard leachate tests- the Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the U.S. Army Corps of Engineers-EPA seawater elutriant test. While the wastes generated in the laboratory may not be entirely representative of those to be generated in full-scale plants, results of these studies provide a positive indication that commercial recovery of cobalt, copper, manganese, and nickel from manganese nodules would be environmentally acceptable.

Jan 1, 1985

By Gene R. Reid

The contract objective is the development and in mine testing of an Automatic Fire Control System (AFCS) for mobile underground metal mining equipment. The effort described by this report covers the period from June 21,1975 through June 30,1976 and accomplished the following tasks: ? Preparation of Data Handling Plan and data acquisition which included visits to twenty mine sites in eleven states, visits to Bureau and MESA facilities, and a literature survey. ? Data analysis which determined the most hazardous type of vehicle for use in the demonstration, and design requirements for the AFCS, ? Development of recommended design concepts for the AFCS. ? Design and development of the AFCS including tests on a full-scale mock-up of a load-haul-dump (LHD) vehicle. ? Underground fire tests on an ST-2B-LHD vehicle at the Hecla Lakeshore mine Casa Grande, Arizona.

Jan 1, 1976

By John W. Kopp

A major concern with blasting at surface mines is generation of ground vibrations and airblast and their effects on nearby residences. This Bureau of Mines report looks at the use of millisecond delays in blast design and their effect on the resulting ground vibrations and airblast. A total of 52 production blasts were instrumented and monitored at a surface coal mine in southern Indiana. Arrays of seismographs were used to gather time histories of vibrations and airblast. The data were analyzed for peak values of vibration and airblast and for frequency con-tent. Various delay intervals were used within and between rows of blastholes. Delay intervals within rows were 17 and 42 ms, and those between rows ranged from 30 to 100 msj these intervals are equivalent to 0.5 and 1.3 ms/ft within rows and 1.2 to 4.3 ms/ft between rows. Sub-sonic delay intervals within rows reduced airblast by 6 dB. Large delay intervals between rows reduced the amplitude of ground vibrations; their frequency depended primarily upon the geology of the mine site.

Jan 1, 1986