Search Documents

By Ralph B. Youtz

This paper describing mining methods at, the Eighty-Five mine of the Calumet and Arizona Mining Co., Valedon, N. Mex., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts in the United States. The Eighty-Five mine is in southwestern New Mexico, 3 miles southwest of Lordsburg, Hidalgo County (see fig. 1). The mine produces normally 7,000 to 8,000 tons per. month of silicious copper-gold-silver ore, and employs approximately 200 men underground and 40 on-the surface. Mining is done by shrinkage and cut-and-fill methods.

Jan 1, 1931

By D. R. Tweeton

The U.S. Bureau of Mines, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research Organization, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in locating a brine solution simulating in situ leach solution or a high-conductivity plume of contamination. The brine was approximately 160 m below the surface. The testsite was the University's San Xavier experimental mine near Tucson, AZ. Geo- physical surveys using surface and surface-borehole, time-domain electromagnetic (TEM) induction; surface controlled-source audiofrequency magnetotellurics (CSAMT); surface-borehole, frequency- domain electromagnetic (FEM) induction; crosshole FEM; and surface magnetic field ellipticity were conducted before and during brine injection. The surface TEM data showed a broad decrease in resistivity. CSAMT measurements with the conventional orientation did not detect the brine, but measurements with another orientation indicated some decrease in resistivity. The surface-borehole and crosshole methods located a known fracture and other fracture zones inferred from borehole induction logs. Surface magnetic field ellipticity data showed a broad decrease in resistivity at depth following brine injection.

Jan 1, 2010

By E. G. King

Thermodynamic calculations involving the oxides of tungsten and molybdenum have been hampered by lack of accurate entropies and high temperature heat contents. This paper presents work by the Federal Bureau of Mines on new low-temperature heat-capacity data leading to the evaluation of the 298.15° K. entropies of tungsten dioxide and tungsten trioxide, as well as high-temperature heat contents (above 298.15° K.) of molybdenum dioxide, molybdenum tri-oxide, tungsten dioxide, and tungsten trioxide. Included are heats of fusion of the two trioxides. The heats of formation at 298.15° K. of these four oxides are tabulated as measured by Mah4 5/ of this laboratory. Included also are the 298.15° K. entropy of Mo02 measured by Kin 6/ of this laboratory, and that for Mo03 according to Kelley and King.7/ These basic data provide a consistent compilation from which to perform accurate thermodynamic calculations involving these compounds. No previous low-temperature- heat-capacity measurements have been reported for tungsten dioxide. Seltz, Dunkerley, and DeWitt8/ measured the low-temperature heat capacity of tungsten trioxide. The only previously-reported high-temperature heat-content measurements for any of the oxides were conducted by Cosgrove and Snyder,9/ who measured molybdenum trioxide to 1,300° K.

Jan 1, 1960

By R. H. Nafziger

Owing to the growth of alloy steel production and its influence on tramp element levels when recycled, foundries have expressed concern regarding the quality of scrap used to prepare iron castings. Reliable and current information was unavailable on the amount of tramp elements contained in iron castings over time. Accordingly, the U.S. Bureau of Mines, in cooperation with the American Foundrymen's Society (AFS), analyzed cast iron samples from participating foundries throughout the United States on a quarterly basis to ascertain possible trends. Each sample was analyzed for 28 elements to determine if changes had occurred as a function of several input variables. This bulletin describes the research and presents analytical results and evaluations over a 5-3/4-year period from January 1981 to September 1986. Results show that iron casting compositions are changing with respect to a few tramp elements such as arsenic, cobalt, chromium, tin, and zinc over the period. Changes in charge compositions probably are responsible. Significant variations between zones also were observed with aluminum, arsenic, cobalt, chromium, copper, and manganese.

Jan 1, 1990

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and, education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing mineral substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970's, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and fuels.1

Jan 1, 1977

By J. W. Lyman

The U.S. Bureau of Mines investigated methods of separating valuable rare-earth materials from Fe in neodymium iron boron (NdFeB) magnet scrap. A selective oxidation treatment of the scrap oxidized the rare-earth portion while leaving elemental Fe. Magnetic and leaching procedures were tried for separating the metallic Fe and rare-earth oxides, but the extremely fine grain size of the oxidized scrap prevented recovery by either technique. The best separation of rare earths from bulk NdFeB magnet scrap was obtained by dissolution with H2S04 followed by precipitation of recyclable rare-earth salts. By precipitating neodymium-alkali sulfate double salts as an intermediate that can be converted to a variety of useful products, many materials-handling and economic disadvantages found with direct precipitation with fluoride or oxalate were avoided. Iron was removed from magnet leach solutions by precipitation as a jarosite, eliminating a major disposal problem. Research was also conducted with contaminated mixed SmCo5 and NdFeB swarf. Using a flotation-leaching technique allows the SmCo5 to concentrate in the froth, while the grinding-medium contaminant sinks and is removed as tailing. The NdFeB is dissolved by H2S04 during the process.

Jan 1, 2010

By K. E. Robinson

Appendix A is an abridged extract of the report prepared by the Geotechnical and Structural Engineering Society of Idaho, and presents the results of their one-year study to evaluate the feasibility of disposing mill tailings by landfill construction. Appendix B describes the field and laboratory testing program completed by RDM to assess the effectiveness of a soil (slimes) liner as a means of seepage control to reduce the introduction of contaminants into the local ground water regime. Appendix C presents a summary of a thesis by Lawrence Martin on the analysis of the acid production potential of mill tailings, and the results of geotechnical testing of mill tailings completed by ROM. Appendix D describes potential landfill sites identified within the study area, the development of these sites to meet the present needs of the mining industry and the future requirements of the community is described. Appendix E summarizes the main legislation impacting on tailings disposal. Appendix F discusses the environmental and socio-economic factors that should be considered.

Jan 1, 1981

By Fred Hodges

This paper describing the concentrator practice of the Hurley Plant of the Nevada Consolidated Copper Co. at Hurley, N. Mex., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Hurley concentrator has a normal daily capacity of 13,500 tons of ore, and for the first four months of 1930 the heads of the concentrator averaged 1.32 per cent of copper and 3.14 per cent of iron. The recovery for this period was 83.98 per cent and the concentrates produced averaged 27.54 per cent of copper.

Jan 1, 1931

By David J. Kusler

The Bureau of Mines reviewed current technology in the refractories consuming industries and evaluated the impact of changes in technology on the supply and demand of refractories. Literature was searched and contacts were made with leading consumers and producers of refractories. The distribution of refractories by value of shipments to users was surveyed. The report shows that the percentage distribution of refractories sales to the consuming industries has remained essentially constant during the last decade but that substantial changes have occurred in the relative distribution of types of refractories. The trend in pyroprocessing technology in recent years has been toward higher temperatures, which require more costly refractories. This fact is reflected in the impressive gain in the dollar value of refractories sales, which in 1968 was about one-third greater than in 1960, and the rapid growth of refractories based on high-alumina, magnesia, zirconia, carbon, and other materials, at the expense of fire clay, silica, and chrome- based refractories. An appendix to the report contains refractories value and shipment data tabulated in a manner by which trends in the distribution of refractory types can be observed from 1955 to 1968. In addition, unit values are presented on a per-ton basis for comparison.

Jan 1, 1970

By Thomas R. Bur

The strain and pressure gage methods for evaluating the relative performance of explosives in rock were compared. This comparison was based on a study of the responses of strain and pressure gages to explosion-generated seismic waves. Several explosives) representing a wide range of detonation pressures) were used. In general the relative performance of these explosives) as determined from amplitude) impulse parameter) and energy parameter measurements) is the same if the compressive portion of the strain pulse and the comparable portion of the pressure pulse are considered. Other similarities and differences of the two methods are also discussed.

Jan 1, 1967

By WILLARD W. CUTLER

This bulletin reviews, in the light of recent experience, the use of production-decline curves in estimating the future production of oil from wells. It deals with the estimation of the reserves of recoverable oil in properties already producing or in those adjacent to them, takes cognizance of the physical laws governing expulsion of oil from oil sands, and shows how the production-decline curve can be made to utilize these laws in estimating reserves and rates of production. The valuation of oil properties should be based on the total amount of oil recoverable from a property by the methods in use, the rate of recovery, the cost of production, and the selling price. Numerous other curves besides those for reserves and rates of production may be formed from the production-decline curve and will present desired information in a convenient time-saving form. These curves also are described. Methods developed before the production-decline curve method was used are briefly discussed in order that the principles on which estimations of oil reserves are based may be made plain. The construction of curves and tables for estimating future production of individual wells and of average wells in most of the important oil districts of the United States is described and operating problems that may be solved by the use of production-decline curves are discussed. The bulletin does not deal with costs, oil prices, or the methods of evaluating oil properties. Many engineers have amply demonstrated the value of the production- decline curve method by forecasting within reasonable limits the production of many thousands of wells and tracts. The value of similar estimates depends however, on (1) the application of trustworthy methods; (2) the care and judgment of the estimator; and (3) the length and reliability of the records and the accuracy of ofher information used in estimating future production. When adequate records and information are available, experience has shown that It qualified engineer can forecast production far more accurately than has been deemed possible, except where the usual conditions governing the expulsion of oil from a sand have been radically changed by applying compressed air or by flooding with water, or, to a less degree, by using vacuum. In general, the production-decline curve method, though there are limits to its accuracy, is far more trustworthy than any other.

Jan 1, 1924

By Robert L. Kranz

Mining-induced microseismicity data collected by the U.S. Bureau of Mines in a hard-rock mine were analyzed for spatial and temporal patterns that might prove useful for prediction of rock bursts or assessment of rock mass damage changes. Pattern attributes described and illustrated in the previous report (part 1) were applied to the study of aftershock sequences associated with two different stopes. The aftershock sequences were spatially and temporally fractal, and the fractality was maintained for up to 16 h following a sequence progenitor. This suggests mechanical interdependency among the after-shocks. No statistical difference was found in the distributions of fractal dimensions when comparing two different stopes or when comparing aftershock sequences initiated by blasts or bumps. This suggests a lack of sensitivity to both stress perturbation mechanism and local damage states. However, differences between the two stopes were found in other sequence attributes that support inferred differences in the magnitude of stress concentrations and damage near each stope, and over time as a stope is developed.

Jan 1, 2010

By George S. Rice

The prevention of coal-mine explosions has been one of the chief purposes of the Bureau of Mines. In facti the first Federal appropriation relating to mining methods, in 1908, authorized the investigation of the causes of mine explosions and the possible methods of preventing them. When that investigation started the mining industry had not determined the real causes of a succession of terrible coal-mine explosions in various countries, culminating in the great disasters at CoulTièl'es, France, and Monongah, W. Va. Coal dust as an agent of widespread explosions had been under suspicion, and watering to allay the dust was recommended by some mining engineers but the watering of coal-mine dust was adopted in comparatively few mines of the United States and Great Britain, and had not been introduced widely in any country except Germany. Rock dusting, another method of preventing explosions of coal dust, was early tested with success by the Bureau of Mines in its fist gallery at Pittsburgh and, beginnig in 1911, at the experimental mine, Bruceton, Pa. Several of the fist publications i of the bureau suggested that rock dust be used in gaseous or dusty bituminous mines, and in 1915 Technical Paper 842 strongly recommended it. Since that time additional tests in the experimental mine have fully confied this :ft judgment.

Jan 1, 1924

By Oliver Bowles

Manufacture of lime is one of the oldest industries. Plants are distributed widely and furnish an essential raw material for numerous commodities. Use of lime in hundreds of manufacturing and chemical processes, by the building trades, and in agriculture has created a demand for large production and has necessitated exhaustive research on methods of manufacture and uses. The bibliography of publications on lime is extensive; but, for the most part, each publication has dealt with individual operations. The purpose of this paper is to present a general picture of the industry as a whole. The abundant literature has been abstracted and quoted freely, and the National Lime Association has furnished valuable data for certain sections. Publications containing more-detailed information on the various branches of the industry are referred to in the footnotes and bibliography.

Jan 1, 1952

Recommendations from 44 mining industry workshops are summarized and reviewed in the context of Bureau of Mines research and development programs on-going during the period 1974-1977. Approximately 1,000 specific recommendations for research and development are summarized in a systematic and comprehensive format appropriate for review by mining research and development program managers. Relevant Bureau of Mines research programs are briefly described and some opportunities for future research and development are identified.

Jan 1, 1979

By Abdo F. Bayazeed

A survey of the underground injection of steel processing waste pickle liquor (WPL) was made by Bureau of Mines engineers. Hydrochloric and sulfuric acids WPL are being injected into deep wells completed in the Cambrian age Mt. Simon Sandstone Formation in Illinois and Indiana. The Mt. Simon Formation ranges up to 1,800 feet in thickness. The average depth of WPL injection wells is 4,000 feet, and injection is mostly by gravity flow at rates as high as 4,000 barrels per day. The details of the design and operating history of a WPL well located near Gary, Ind., are discussed. Laboratory tests showed that the Mt. Simon Sandstone is sensitive to fresh water. The adsorption of iron and neutralization of acids by sandstone cores from deep wells and an outcrop were determined.

Jan 1, 1973

By Robert J. Hundhausen

This report describes Bureau of Mines investigations of a low-grade scheelite-bearing granodiorite intrusive situated on Henderson Creek, Granite County, Mont. The intrusive is in a narrow, V-shaped valley at the head of extensive placer workings. Since May 1943 the H. & R. Mines Co. of Portland, Oreg., has recovered scheelite sand and gold from the placer workings. A modified Yuba, 4?cubic foot bucket dredge was used in the operation. By February 1947 this operation had recovered and marketed over 215,000 pounds of scheelite concentrates containing 63 percent WO3. The scheelite in the placer was found to be derived principally from erosion of the granodiorite intrusive. The intrusive is one of a series of four similar, dikelike masses of granodiorite whose outcrops are aligned along a 10-mile zone of weakness trending N. 60° E. The intrusive has a triangular outcrop exposed over an area of 57 acres. Trenching and sampling by the Bureau of Mines demonstrated that scheelite is sparsely distributed throughout the granodiorite. This work delimited the outcrop of the intrusive and indicated a large submarginal reserve of low-grade tungsten mineralization. The deposit is ideally suited for exploitation by large-scale, open-pit mining operations; it would be easily available in a national emergency. Additional exploration would be necessary, however, before large-scale production plans could be made efficiently or accurately.

Jan 1, 1949

By S. J. Gerdemann

In support of its objective to improve mine safety, the Bureau of Mines has searched for better materials and systems to anchor roof bolts. TIlis report describes a study on the effects of mine waters upon accelerated gypsum, one of the materials under consideration. The accelerated gypsuw dissolved at an appreciable rate relative to an assumed 10-yr life span of a roof bolt. Surface orientation, initial ion concentration of a dissolving solution, and flow rate of the solu-tion had substantial effects on the dissolution rate. Factors such as water-cement ratio, accelerator content, wax capsule additions to the gypsum in cartridge-installed bolts, surface area, temperature, and curing duration had little effect. In an actual roof-bolt environment, dissolution will occur in static solutions to the solubility limit of gypsum (~2 giL) and cease, result-ing in minimal damage; but in flows of unsaturated solution as slow as 1 L per month, a loss of up to 10 pct will occur in 2 yr. Since miners cannot readily measure the flow or ion concentration of static-appearing water at every roof-bolt site, all such water must be assumed to be pure and flowing. It is recommended that gypsum-bonded roof bolts be confined to dry roofs only.

Jan 1, 1983

By Peter N. Gabby

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 27,034-hectare Steel Mountain/Yuba River study area and the 16,544-hectare Breadwinner study area. There were approximately 535 lode and placer claims in or partially in the Steel Mountain/Yuba River study area, and 84 lode and placer claims in or partially in the Breadwinner study area. In the Atlanta and Rocky Bar mining districts, both adjacent to and in the Steel Mountain/Yuba River study area, 30,232.4 kg (972,000 02) of gold and 62,838.3 kg (2,020,000 02) of silver had been produced. Most of this production came from outside the study area. Placer properties adjacent to (and a few in) the Breadwinner study area had production of 93.1 kg (2,992 oz) of gold and 20.0 kg (642 02) of silver. Twelve properties in the Steel Mountain/Yuba River study area have potential for resources; eleven have alteration and/or mineralization similar to that found at Atlanta with potential for gold, silver, and tungsten resources, and one has alteration and mineralization associated with polymetallic vein type deposits with potential for gold, silver, copper, lead, zinc, and tungsten resources. Adjacent to the study area, large bars of gold-bearing gravel can be found along the Middle Fork Boise River. Four properties in the Breadwinner study area have potential for mineral resources; one has alteration and mineralization associated with skarn, polymetallic vein, and, possibly, copper-molybdenum and molybdenum porphyry types of deposits; two have alteration and metal assays associated with polymetallic vein, and possibly copper-molybdenum and molybdenum porphyry types of deposits; and one has alteration and mineralization similar to that found at Atlanta. These four have potential for gold, silver, copper, lead, zinc, molybdenum, and tungsten resources Adjacent to and extending into the Breadwinner study area are large bars of gold-bearing gravel along North and Middle Forks Boise River.

Jan 1, 1993

By Frank J. Cservenyak

Curtailment of bauxite importation by enemy activities during World War II focused attention on the necessity of developing domestic deposits of aluminous materials. Large quantities of aluminum ores such as kaolin, siliceous bauxites, high-iron bauxites, anorthosite, and diaspore clays are available but not readily amenable to Bayer processing because of excessive impurities. The Bayer process, which is the only commercial method in use in the United States for producing metallurgical-grade alumina, requires a high Al2O3 bauxite relatively low in SiO2 and Fe2O3. The Bureau of Mines was charged by Congress to investigate processes for the production of alumina from these low-grade ores. One part of the program was an investigation, in the laboratory and pilot plant, of the recovery of alumina by the lime-soda sinter process. Ores comprising kaolin, diasporic clays, anorthosite, and siliceous bauxites have been investigated and studied in the laboratory and pilot plant, and a series 'of reports covering these investigations has been prepared.

Jan 1, 1948