Search Documents

By D. P. Lindroth

The Bureau of Mines is engaged in research on ground probing radars for detection of geologic hazards in advance of mining. Penetration distances and interpretation models depend on the dielectric properties and wave propagation characteristics for coal measure stratified media. Relative dielectric constants and dissipation factors were measured under ambient conditions for Pittsburgh Seam coal measure rock over the frequency range of 20 to 100 MHz by the susceptance-variation method. The rock types measured were representative sedimentary rock located above the Pittsburgh Coal Seam. Extreme values for the computed attenu-ation distance ranged from 1.7 m at 100 MHz for siltstone to 230 m at 20 MHz for a particular limestone.

Jan 1, 1984

By Cleo G. Rall

The value of brine analyses in the study of petroleum-engineering problems was recognized early in the history of petroleum. The Bureau of Mines before 1928 had indicated in several reports.3/ ways in which analyses might be used. Because of the confusion resulting from attempts to correlate the work of different chemists using greatly varying methods of analysis and systems of computation and expression of results, a paper presenting the methods used by the Bureau of Mines was prepared and published in 1928. This system of determining the characteristic constituents of oil-field waters and of calculating and reporting results has been widely adopted by the petroleum industry. The earliest and most obvious use of water analyses is determination of the source of water infiltrating into petroleum and natural-gas wells. For this purpose it is necessary that an analysis of the connate water of the formation from which the oil is produced be available and that an analysis of the contaminated water be made. By comparing these analyses with those of connate waters from formations higher in the structure, the formation from which the infiltrating water comes may be identified.

Jan 1, 1953

By Ann G. Kim

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, P A. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic? test and subsurface temperatures was not significant.

Jan 1, 2010

By R. R. Lowery

An analysis of three 1-1/4-diam manufactured wire ropes of 6x19 classification was done to identify and describe reference conditions of new rope. Reference condition is of value when examining tested or retired ropes. Measurements of strand and rope pitch and of wire and rope diameter confirmed adherence of all ropes to those construction specifications. Mechanical properties of strength and ductility were determined by accepted methods for the ropes and wires from the ropes. Individual wires from one rope failed to meet minimum wire ductility values. Wire chemical composition varied in average carbon levels, from 0.70 to 0.78 wt pct, and in manganese content, from 0.45 to 0.80 wt pct. One manufacturer's product contained 1 to 3 wt pct Ni and Cr. Heavily wrought pearlitic steel microstructures were porous and contained inclusions. Cold work variations were evidenced by wrought grain width. Recorded anomalies reflected the condition of the manu-factured products. The report provides data that compare the three wire ropes studied, but cannot verify the effects that these conditions or anomalies have on rope service life.

Jan 1, 1983

By R. L. Grayson

"Compliance standards for respirable dust, which are reduced because of high quart: concentrations, have become an industry-wide problem. Research on the physical and chemical character of quart-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quart: particles of a mine dust are ""pure,"" then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. lf, however, quart: is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.Although much research has been done on coal workers' pneumoconiosis (CWP) over the past decades, the etiologic agents of the disease still have not been pinpointed. The predominant methods of characterizing respirable coal mine dusts were bulk analysis techniques for determination of elemental and mineralogical concentrations, the results of which were used in statistical analyses to determine relationships between dust composition and the occurrence of CWP. These methods are incapable of finding the etiologic agents in the dust primarily because of complicated and confounding physiochemical factors, which may be discovered if the focus of characterization was done on a dust particle level.The SEM/EDXA-based research discussed here shows a significant difference in the number of ""pure"" quartz particles in respirable dusts collected from different mines. Some of the results have been reported previously (Grayson, Andre, and Simonyi, 1988). Concurrent research by other investigators (Wallace et al., 1989) demonstrates an SEM/EDXA-based methodology to pinpoint the location of the ""contaminating"" substance(s ) in a quartz-classified particle. The research of the European Economic Community has also begun analyses on the respirable-dust-particle level (Robock and Bauer, 1988).Since the compensatory and intangible costs of CWP are substantial in the United States, it is important that the etiologic agents be determined and then either controlled or neutralized in a cost-effective way. This line of research is especially important consid-ering the forecasted. near-term growth of coal production and the evolution of high productivity longwall panels (an immediate problem in compliance) and continuous mining sections ( a probable future problem).This need has been accentuated now that nearly all respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gem, 1986). Today a real problem exists in the coal industry, both underground and surface, because of high quartz levels in respirable dusts causing substantially reduced compliance standards (Murphy, 1989).The combined results of the respirable dust particle investigators indicate that conventional bulk sample analyses may not faithfully represent the amount of biologically available or active quartz in all mines with a high level (greater than 5% ) of quartz in the dust For example, some mine dusts might contain predominantly occluded (or coated) quartz particles where bulk analysis would result in anomalously high ""free silica"" measurements. The same result would occur when quartz particles are intermixed substantially with other minerals that can alter the surface of the composite particle away from a quartz-behaving character."

Mar 1, 1992

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By R. G. Knickerbocker, C. T. Baroch, A. W. HACKWOOD

The difficulties inherent in the production of alumina by the formation of potassium alum and its subsequent thermal dehydration and decomposition have been overcome , to a large extent , in a process developed at the Boulder City Station of the Bureau of Mines . This process is applicable to the reserves of alunite known to occur in several Western States and , possibly , to certain clay and low-grade bauxite deposits known to exist in this country . The operations sequence of the process is shown in the flow sheet (fig . 1) . Only those steps included within the heavy line are considered in this report . Four different procedures for dehydration of alum were investigated ; ( 1 ) Spray drying , ( 2 ) rotary - kiln drying , ( 3 ) dry grinding in a thermal ball mill , and ( 4 ) dehydration in the vertical- column flash dehydrator . Based upon fuel requirements and other practical considerations , the vertical- column dehydrator , or some modification of its operating principle , offers the botter possibility for commercial use .

Feb 1, 1946

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By G. E. McElroy

Tae purpose of this paper is to present types of charts adapted to aid in the graphic solution of fan-performance problems of selection and operation, and to urge the adoption of similar charts by the National Association of Fan Manufacturers as standard forms for presenting fan-performance data. As matters now stand, it is difficult for the average engineer to solve such problems because a laree number of variables are involved, and performance data are not presented in a manner that permits their direct application to many problems encountered in practice. The performance of any centrifugal machine is determined not only by the machine itself but also by the fluid-flow system on which it operates. Actual performance of centrifugal fans is therefore e matter of the type, size, and speed of fan, on the one hand, and of the relation of pressure to quantity of flow, as determined by the physical condition of the airway system, on the other.

Jan 1, 1936

By G. E. McElroy

[The purpose of this paper is to present type: of charts adapted to aid in the graphic solution of fan-performance problems of selection and operation, and to urge the adoption of similar charts by the National Association of Fan Manufactures as standard forms for presenting fan-performance data. As matters now stand, it is difficult for the average engineer to solve such problems because a large number of variables are involved, and performance data are not presented in a manner that permits their direct application to many problems encountered in practice. The performance of any centrifugal machine is determined not only by the machine itself but also by the fluid-flow system on which it operates. Actual performance of centrifugal fans is therefore a matter of the type, size, and speed of fan, on the one hand, anti of the relation of pressure to quantity of flow, as determined by the physical condition of the airway s: stem, on the other.]

Jan 1, 1936

By A. T. Coumbe

The first survey 3/ covering sales of liquefied petroleum gases was made in 1930 by the Bureau of Mines, which at the time was under the United States Department of Commerce. This original canvass covered national totals for 1922 through 1929, and most of the supply came from natural gasoline plants. The 1930 report showed approximate totals for butane and propane and for butane-propane mixtures and pentane grouped together. No attempt was made to breakdown the national sales by various uses until 1931, when the quantities for domestic or household consumption, gas manufacturing, and industrial requirements, including miscellaneous uses were indicated. As the market for these liquid petroleum gases expanded and as new uses came into importance, their respective quantities were shown separately in the annual survey. Sales for internal-combustion engine fuel and for raw material for chemical plants were first taken out of the industrial total in 1936. During World War II liquefied petroleum gases became important as feed stock diverted to synthetic rubber plants, and consequently the survey was broadened to cover this particular demand, beginning in 1944. Pentane was dropped from the survey after 1943, as, being liquid at atmospheric pressure, it is not considered as one of the liquefied petroleum gases and furthermore, the quantity reported made up less than 1 percent of the total sales. Thirteen producing companies reported to the Bureau in the first survey made in 1930, and in the 1952 canvass about 130 producers--petroleum refiners and natural gasoline companies--and about 1,300 dealers cooperated by filing schedules showing a breakdown of their sales. Their 1952 deliveries of approximately 4.5 billion gallons of liquefied petroleum gases were equivalent to about 3.4 billion gallons of gasoline or 3.1 billion gallons of distillate fuel oil.

Jan 1, 1954

The influence of fuel additives on automobile exhaust emissions was studied using engines currently found in the U.S. vehicle population. The fuel additives used in the experiment were four multifunctional additives and one lead antiknock additive. Experimental work was done to determine both the direct effect of the additive per se on exhaust emissions and the influence of Long-term additive effects on emissions with mileage accumulation. Results showed no significant direct or intermediate effect on exhaust emissions for any additives tested. In subsequent experimental work concerned with the long-term or indirect effects of additives, the detergent-dispersant additives were found to have little influence on emissions when used in conjunction with high-quality oil and motor fuel. The lead (tetraethyl) antiknock additive increased exhaust hydrocarbons approximately 12 to 17 percent during a 4,000-mile accumulation period using a base fuel containing 2 ml of tetraethyl lead per gallon. An unleaded fuel was used during a similar accumulation period with no significant increase in exhaust hydrocarbons with mileage.

Jan 1, 1971

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966

By Scott W. Hazen

This report describes exploration for lead-zinc ores at the Madonna mine between 1945 and 1953 by the Utze Lode Co., the Bureau of Mines, and the company with Government financial aid under the Defense Production Act of 1950. The Madonna mine yielded silver, lead, and zinc with a net smelter value of over $5,000.000. from 1882 to 1924. The mine was inactive from 1924 to 1942 when the Utze Lode Co. acquired the property. Possibilities for finding ore in the mine, especially at depth, were considered favorable. The Utze Lode Co. began rehabilitating the Madonna mine in 1945. An exploration program, which consisted of winze sinking and drifting, failed to produce commercial are.

Jan 1, 1956

By Donald P. Schlick

Respirable dust provisions of the Federal Coal Mine Health and Safety Act of 1969 are designed to protect the most important resource of the coal mining industry--its workers. The Act imposes two respirable dust standards of 3.0 milligrams per cubic meter of air after June 30, 1970; and 2.0 milligrams per cubic meter of air after December 30, 1972. Under Federal regulations, each operator is required to carry out a dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare, This program features the sampling of "high risk" face workers to establish that the exposure of each miner is below the dust standard, Mining sect ions, continuously in compliance with the regulations, may sample at less frequent intervals. In addition to requiring the mining company to take respirable dust samples, the Bureau of Mines will perform in-depth dust inspections twice a year, as well as frequent "spot inspections." The Bureau has established a semiautomatic computerized operation capable of processing over 1 million samples per year. This facility will be linked to various Bureau offices by a telecommunications system to provide automatic data printouts within hours after samples have been weighed.

Jan 1, 1970

By Michael T. Nigbor

This Bureau of Mines publication identifies the significant environmental issues associated with the potential development of strategic and critical minerals in the Stillwater Complex, MT. The Stillwater Complex contains deposits of Cr, platinum-group metals (PGM), and Ni. Issues that must be addressed prior to minerals development include the effects mining, milling, and smelting will have on the land, water, and air, and methods of minimizing the environmental impacts.

Jan 1, 1985

A concise country-by-country summary of the mineral industry of Africa is presented. Reserves, resources, role of the country in the world mineral supply, and developments in the mineral industries are reviewed. The data on each country are accompanied by a map showing mineral location and transportation facilities.

Jan 1, 1976

By Effie T. Kurt, Jack Wright, J. W. Watkins, Cynthia Pearson

"The analysis of water produced with crude petroleum has interested oil producers since inception of the industry. Records of the first analysis of mineralized water produced from an oil-productive formation are obscure, and references to the first use of brine analyses to assist in solving problems of petroleum production are not available in the technical literature. However, many early reports of the Federal Bureau of Mines 5-8/ and. Federal Geological Survey, 9-11/ as well as articles in engineering and geological placed special emphasis on journals ,12-l4/ the importance, interpretation, and application of water analyses.One of the earliest applications of water analyses, and still a major one today, is for identification of intrusive waters in oil wells. This may be done by comparing the chemical constituents of a sample of water indigenous to the oil-productive formation with those of samples from upper, water-bearing formations within the same general area. Some earlier investigators recognized the need for analyzing samples of all waters encountered in drilling operations. Ambrose15/ stated, in part, ""In wells being drilled, the engineer should grasp every opportunity to get a true sample of water from each sand. . .,"" and, ""The waters of each oil field are chemically different from those of another field."" The validity of the latter observation and the importance of the former one have been borne out by comparing the results of analyses of many samples and noting the differences in relative concentrations of like constituents of waters from the same geological formation in different localities or oil pools."

Apr 1, 1957

By Floyd R. Hertweck

The helium resources of the United States were estimated by the Bureau of Mines to be 1,037 Bcf as of January 1, 1981. These resources are divided into four categories, in decreasing degree of assurance of their existence: (1) helium in storage and in measured natural gas reserves, which totals 211 Bcf, (2) helium in indicated natural gas resources, which is estimated at 207 Bcf, (3) helium in hypothetical natural gas resources, which is estimated to be 318 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 301 Bcf. These helium resources are further divided into depleting, nondepleting, and stored classifications, The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. All of the helium in undiscovered (hypothetical and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 897 Bcf of the total helium resource base. Nondepleting resources are those in shut-in, abandoned, or otherwise nonproducing natural gasfields. Helium resources contained in nondepleting natural gas resources are estimated to total 100 Bcf. There is 40 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, Tex.

Jan 1, 1983

By D. A. Douglass

This report describes the tri-n-butyl phosphate extraction of cerium (IV) from a sulfate leach liquor prepared from a bastnaesite concentrate as well as from pure eerie nitrate solutions. The work was done on a laboratory scale using separatory funnels. Extraction from pure cerium solutions entailed no great difficulties; however, extraction from the bastnaesite solution proved more difficult, mainly because of the inhibiting effect of the sulfate ion. Despite this, procedures were developed for obtaining good single-state cerium extraction (95+ percent) and a high-purity product (99+ percent), although the maximization of both cannot be achieved simultaneously. This necessitates a compromise in any extraction scheme.

Jan 1, 1959