Search Documents

By M. M. Fine

The flotation work on samples from nine fluorspar properties in Crittenden and Livingston Counties, Ky., reported herewith was part of a wartime project that resulted in increasing the supply of metallurgical-grade fluorspar. The samples were tailings, dumps, and waste rock that had been rejected in previous milling operations. All were treated successfully by flotation to yield metallurgical-grade concentrates with recoveries ranging from 77.5 to 98.3 percent of the fluorite. After the laboratory testing, the results of which were available to the owners and operators of the properties, many of the tailing ponds and rock dumps were milled. The real value of this report, therefore, is to show the operators of gravity concentration plants the possibilities of re-treating waste products by flotation either at some future time or currently with the gravity

Jan 1, 1948

By Larman J. Heath

Preliminary results of an explosive fracturing-solvent injection heavy oil recovery experiment conducted by the Bureau of Mines at a shallow oil reservoir near Bartlett, Kans., are given. Three wells 35 to 50 feet apart were drilled to a depth of 360 feet, and an open hole interval from 300 to 350 feet in the Bartlesville Sandstone Formation was explosively fractured with 3,000 pounds of pelletized TNT in each well. Laboratory tests were made on cores obtained from these wells to confirm the suitability of using an aromatic-type solvent. Injection of a 74-percent aromatic solvent was begun into one well and continued intermittently for approximately 2 months. Crude oil production amounted to 29.6 bbl, or 11.7 percent of the total oil con¬tained within the three-well interwell zone.

Jan 1, 1972

By B. P. Martinez

A process for regenerating spent pickle liquor is proposed in which some of the water is evaporated at atmospheric pressure and ferrous sulfate is precipitated as monohydrate crystals..Equilibrium conditions are set for a slurry of crystals in a mother liquor containing 5 percent FeS04 and 45 percent E2S04, by weight, and boiling at about 235° F. The slurry is pumped continuously to a filter, and the mother liquor from the filter is pumped back for reuse in the pickling tanks. The net result of the process is to remove ferrous sulfate in the regeneration plant at the same rate ac it is produced in the pickling tanks. This process is integrated with the steel-pickling operation and controlled by the pickling requirements for particular steels. Spent pickle liquor is removed for regeneration continuously from both batch and continuous picklers at higher acid concentrations than would be dumped to waste because no acid is neutralized or discarded. However, the process is not designed to keep a sulfuric acid concentration stronger than 25 percent in any pickling tank. To retain flexibility in the pickling operation, all acid makeup is added to the pickling tanks. Rinse waters are used as water makeup for the pickling tanks. To further minimize waste of acid in the rinse waters, improvements of rinsing practices are outlined.

Jan 1, 1953

By R. M. Gooding

This paper presents a short history of the production of mineral-energy fuels and energy from waterpower in the United States, with brief discussions of the utilization of each of the fuels and hydropower, and a look at fuels competition and interchangeability. Basic data, in figures and tables, are brought together in this publication for the production of coal in the United States from 1800 to 1960, for crude petroleum, natural gas liquids, and natural gas from 1859 to 1960, and for hydropower since 1900. Production for each segment of the fuels complex in the principal producing States from 1946 to 1960 is shown. Data are not included for consumption as such or for imports and exports.

Jan 1, 1963

By R. M. Gooding

This paper presents a short history of the production of mineral-energy fuels and energy from waterpower in the United States, with brief discussions of the utilization of each of the fuels and hydropower, and a look at fuels competition and interchangeability. Basic data, in figures and tables, are brought together in this publication for the production of coal in the United States from 1800 to 1960, for crude petroleum, natural gas liquids, and natural gas from 1859 to 1960, and for hydropower since 1900. Production for each segment of the fuels complex in the principal producing States from 1946 to 1960 is shown. Data are not included for consumption as such or for imports and exports.

Jan 1, 1963

By S. L. McGill

The U.S. Bureau of Mines has determined the microwave heating rates for a suite of minerals and reagent-grade compounds. Maximum temperature achieved for the samples and the time required to reach temperature are reported. Heating rates of powdered samples are presented as a function of incident powers up to 3,000 W at 2,450 MHz. Descriptions of the microwave cavities, test cells, and a thermocouple assembly used to measure temperature in the microwave field are given. Many minerals of value heated in the microwave field, whereas host rock or gangue materials did not. In general, heating rates increased as incident power was increased. Exceptions to this were some very good (CuO, Fe304, and PbS) and very poor (CaC03 and SiO2) microwave-absorbing materials that showed negligible changes with increased power. Applications demonstrating the use of microwave energy in mineral processing that are described herewith include oxidation-reduction reactions, mineral liberation, and mercury retorting-vaporization. Microwave data on mineral heating rates will provide insight to possible chemical and mineral processing applications as well as assist in predictions of processing parameters.

Jan 1, 2010

By Joseph F. Davies

Along with the humanitarian need for preventing accidents the cost of injuries must be considered. As a means of bringing the facts concerning the prevalence of accidents in mining and their direct cost before the operating officials and others interested in accident prevention in the mining industry, the United. States Bureau of Mines ha as recently made studies and published reports dealing with these subjects in several States 4. This report gives available data on the causes and direct costs of accidents in Virginia coal mines for the 4-year period 1929 to 1932, inclusive. Mounting compensation costs and insurance rates resulting from mine injuries indicate the necessity of measures to decrease the number and severity of accidents. These direct costs, as well as additional losses of an indirect nature, can be eliminated from the cost of production to the extent that accidents are prevented or reduced in severity.

Jan 1, 1934

By Russell G. Warncke

"This report is based primarily on a study of safety conditions and practices followed in the coal mines of Japan. Not all of the coal fields in Japan were studied, but typical mines in the largest producing areas and a fair cross section of coal-mine-safety conditions observed during February to April 1948 are described.Information was obtained through investigations conducted in the mines, discussions with mine-management officials and representatives of labor unions of the various mines visited, and examination of records and statistics from the various offices of the Coal Board of the Ministry of Commerce and Industry and from the Coal Association of Japan. Statistical data covering the same subject, obtained from different sources, varied in many respects and apparently were reported inaccurately, but such discrepancies can be attributed to different methods of reporting and compiling statistics.It is difficult to correlate the high fatal and nonfatal injury rates that prevail in Japanese coal mines with the conditions observed in the mines. Virtually all mines visited were attempting to prevent accidents and explosions, by apparently following known safety precautions for the prevention thereof. Some commendable safety innovations were observed at several mines; they indicated that mine officials are giving thought and consideration to hazardous conditions that affect their particular mines.Naturally, the operating officials and management were anxious to impress the writer with their interest in accident prevention and safety. Operating officials were found to be receptive to safety and wore interested in formulating definite safety programs. Some nines had well-planned and well-organized safety programs, which, if put into effect, would contribute greatly toward reduction of accidents.The approach to safety in Japan is quite different from that in the United States, especially the concept of personal responsibility for accidents and the extent to which the individual should be protected against hazards. Management is responsible for providing and maintaining safe working conditions. Collaboration between management and worker, as understood in the United States, does not exist in Japan.Increase in accidents since the cessation of hostilities is the result of unsettled economic conditions in the coal industry, influx of inexperience workers, and breakdown of discipline among the miners, who have been organized into unions. Those unions are greatly influenced by ""leftist"" tendencies.It was observed that the Japanese mine worker is fatalistic by nature and has little, if any, noticable safety consciousness. The most urgent major requirements to reduce accidents in the coal mines are to train the worker in accident prevention and instruct him regarding the inherent hazards of his occupation.Revision of the mining laws would help to reduce accidents if the companies would comply with such laws and provide safer working places and if the workers would cooperate with management and observe and comply with such laws as are enacted for their protection."

Dec 1, 1949

By W. M. Mark

This investigation was undertaken to develop methods to improve the quality of titanium sponge produced by the Bureau of Mines modification of the Kroll magnesium reduction process. Research revealed that by systematic elimination of detrimental impurities introduced with the raw materials and by improved handling and processing techniques, high-quality ductile titanium with a hardness of less than 110 B.h.n. (Brinell hardness number) can be produced consistently. This improvement was accomplished by helium (or argon) stripping of residual atmospheric and other dissolved gases from the titanic chloride, preliminary dehydration of crude titanium sponge, and careful regulation of the titanium tetrachloride (TiC14) feed rate to the reactors.

Jan 1, 1960

By C. W. Smith

The U.S. Bureau of Mines; Tuscaloosa Research Center, in cooperation with the U.S. Army Corps of Engineers under interagency Agreement No. 14-09-0078-1510, conducted a comprehensive sampling program of 10 upland disposal sites along the Alabama, Black Warrior, and Tombigbee River systems in Alabama. Samples from each site were characterized according to particle size, chemical analysis, mineralogical content, and potential end use. Additionally, samples were subjected to the Toxic Characteristic Leachate Procedure to determine the presence of potentially harmful heavy metals. Based on the results of these studies, each sample was determined to have properties amenable for use as aggregate in general-purpose portland cement concretes and certain asphalt concrete applications.

Jan 1, 2010

By J. A. CoRGAN, J. A. DECARLO

The coal -carbonizing industry is recognized as one of our country's most essential industries , and this position has been achieved through its primary function as a source of supply of special fuels and chemical raw materials . When coal is carbonized at high temperatures in slot - type coke ovens in the absence of air , it decomposes into two main products cokę ... and crude gas . Of these , the more important is coke , a hard, strong, porous solid that remains in the oven after the volatile matter in the coal has been driven out by heat . The hot crude gas carries with it all. of the coke -plant products except coke and has a complex composition in the vapor: state . Its processing , to produce the four principal coproducts of coke (tar , ammonia , light oil, and gas ) , is accomplished by preferential condensation and absorption . Although the principal coproducts of coke tar , ammonia , and crude light oil - - gas, are of secondary importance , their

Jun 1, 1949

By D. A. Rice

As part of a cooperative effort between the Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input from the phosphate industry, the conversion of phosphogypsum to sulfur is being investigated. The proposed process incorporates the thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to sulfur (S°). The research described herein is focused on the latter half of the process. It was demonstrated that calcium sulfide could be converted to ammonium bisulfide (NH4SH), and that ammonium bisulfide could be oxidized by air in the presence of a catalyst, to elemental sulfur, which was adsorbed on the catalyst. Two methods for recovering sulfur from the catalyst were developed: (1) thermal treatment to volatilize sulfur, and (2) leaching the sulfur from the catalyst with liquid anhydrous ammonia. Over 90 pct of the sulfur adsorbed on activated carbon (the catalyst) was recovered by both methods. Based upon the encouraging laboratory investigations, a hydrometallurgical scheme was proposed for the overall conversion of calcium sulfide to elemental sulfur.

Jan 1, 1990

By D. Harrington

The primary objective of this paper is to discuss the hazards and furnish a list of recommendations for the safe operation of quarries and related works. They have been compiled from Bureau of Mines publications covering the safety experience of engineers before and during the year in the mineral industry,5 from a publication of the National Safety Council, Inc.,6 from explosives recommendations made by various explosives manufacturers,7 and from suggestions obtained from quarries visited. The second objective is to describe and illustrate safety devices, practices, and quarrying methods. The quarrying and related industries of the United States had a lower accident-frequency rate than either the metal- or coal-mining industry as reported for 1942.8 However, the quarry industry ranked eleventh in 15 major industries during 1942 in lost-time accident fre¬quency; metal mining ranked fourteenth and coal mining fifteenth.

Jan 1, 1950

By Oliver Bowles

The Bureau of Mines issued three Information Circulars on marble many years ago (5), (6), (7).2/ They have long been out of print; furthermore, conditions have changed considerably in the industry in succeeding years. A presentation of current data is therefore desirable. This report furnishes general information on marble, including its properties, distribution of domestic and foreign deposits, methods and equipment used in quarrying and milling, economic and marketing problems, and recent advances in marble technology. INTRODUCTION Most marbles are crystallized limestone. The term "marble" is derived from a Greek word meaning to sparkle or flash, because the calcite crystals in marble sparkle as they reflect light. The word "marble" is employed frequently to mean a small ball used in the game of marbles with which nearly every child is familiar. Although the little spheres were originally of marble, few of those made in recent years contain that material; nevertheless, the expression "playing marbles" has persisted.

Jan 1, 1958

By Lloyd H. Banning

ELECTRIC smelting tests were conducted at the Northwest Electro-development Experiment Station, Albany, Oreg., to develop a feasible process for producing silicomanganese from siliceous manganiferous material. The Jackson County, Oreg., material used was massive and contained rhodonite as the most abundant mineral. Both raw and beneficiated materials were tested; various proportions and types of fluxes and reductants were used to make up the furnace charges. The silicomanganese product was used successfully in manufacturing various steels at industrial plants. The manganese content of the samples ranged from 23 to 28 percent; silica plus alumina content was as high as 55 percent-about four times the maximum specification for Metallurgical-grade ore. Sink-float laboratory tests indicated that the manganiferous material was amenable to beneficiation. Over 2 tons of rhodonite concentrate was prepared for smelting tests in a sink-float operation. Only the minus-3/4-inch, plus-8-mesh fraction was fed to a heavy-medium cone; over 97 percent of the manganese was recovered in the sink product, which contained 32.4 percent manganese and 44 percent silica plus alumina. About 25 percent of the silica was removed in the float product.

Jan 1, 1959

By L. F. Heising

Ten composite samples of Mesabi Range nonmagnetic taconite from the Hibbing, Minn., area were evaluated by flotation and by reduction roasting-magnetic separation to determine their potential as a future source of iron are. Only one of the composites yielded concentrates that could be considered marketable, using as a criterion a 10-to-1 iron-to-silica ratio. Cursory petrographic examinations of all 10 composited samples and a detailed mineralogical study on 1 sample suggest that unfavorable mineralogical associations between iron and gangue minerals are responsible for their poor beneficiation characteristics.

Jan 1, 1967

By W. G. Hopkins

The development of systems for location of miners who have become entrapped following a mine disaster has been one of the major research goals in the Bureau of Mines. This study details the preliminary development of such a system. Current technologies for locating trapped miners from the surface are either simple direction finders or time difference pulse systems that have accuracy limitations. Developing technologies using full vector field measurements at several receiving points are currently being studied. The necessity of measuring field strength with great accuracy can be a drawback in these systems. A system that operates with continuous wave radio signals, whose phase differences can be measured accurately even in weak signal conditions, greatly improves the location accuracy. A microcomputer would be used in conjunction with the system, to gather and manipulate the data to automatically pinpoint the location of the trapped miner. Comparison of this system with existing technology indicates a favorable accuracy/complexity ratio for the phase difference of arrival technique.

Jan 1, 2011

By Robert Goldstein

A computer program for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. To provide a data base for these calculations, eleven 3-D machine models were prepared and the outputs of three luminaire types were measured. Calculations were done for thirty different configurations.

Jan 1, 1977

Cutter roof failure, a ground control problem that frequently results in massive roof failure, is common in coal mines of the Northern Appala-chian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to predict and prevent its occurrence, and to support such roof when failure occurs or is imminent. Research conducted at the Greenwich Collieries North and South Mines, in central Pennsylvania revealed a correlation between the presence of clastic dikes and formation of cutter roof failure. The research con-sisted of in-mine mapping of geologic and deformational features, rock pressure monitoring, core recovery and evaluation, and in situ stress measurement. It was found that roof failure increased in areas where the occurrence of clastic dikes was most frequent, especially where two or more clastic dikes intersect. Staggering of crosscuts prevented the extension of cutters and deterred the occurrence of large falls extending over several break-throughs. In addition, trusses and cribbing were effective in stabilizing clastic dikes and inhibiting the development of cutter roof failure when employed immediately or shortly after mining.

Jan 1, 1987

By C. H. Riggs

This petroleum-engineering report of the Atlanta oil field in BO them Arkansas reviews reservoir conditions and pressure-production history of one of the important Smackover limestone fields in southern Arkansas. The study of the field was made and the report prepared to aid operators in this and similar fields to increase the efficiency of recovery through the application of better engineering practices. A similar study of the Magnolia field in Arkansas by Carpenter and Schroeder was the first of these reports prepared under a joint agreement between the Arkansas Oil and Can Commission and the Bureau of Mines. The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing oil field; emphasize the importance of conserving known reserves of oil and gas. In recent years vast improvements have been made in the technique of oil recovery, both by better utilization of the natural energy stored in the reservoir and by improved methods of applying external energy to the reservoir system. This report may aid in oil conservation by careful evaluation of the several factors that did or did not contribute the greater recovery in the Atlanta field and by suggesting improvements in production methods and applications.

Jan 1, 1949