Search Documents

By James Paone

This report shows the feasibility of predicting drillability, analytically, by using regression analysis techniques. The approach is new in diamond-drilling research. Further, the study shows that this technique may be of value to drill manufacturers and others in mathematically delineating performance characteristics of new drills in specific rock types. Another application might be the prediction of penetration speeds in extraterrestrial material based on the physical properties of the materials as samples become available. Prediction equations for penetration rates are presented for 9 rocks drilled in the laboratory and for 20 rocks drilled under field conditions. The prediction equations are based on drill operating parameters and on characteristics of the rock penetrated. No single physical property appeared consistently in the best predictor equations, and all the physical properties were found to be highly correlated with each other.

Jan 1, 1966

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness_ It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 33 to 40.0 pct. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3+3 sequence) ranged from 13.3 to 63.3 pct.

Jan 1, 1991

By E. D. Gardner

This is one of a series of papers written for the consideration of operators of small gold and silver mines in the West. The paper discusses smelting schedules, general smelting practices that have a bearing on rates, and the reasons for penalties or credits for certain constituents of ores. Crude gold and silver ores generally are shipped to smelters only when milling facilities are not available; however, high tailing losses in milling a high-grade or refractory ore or low smelting rates because of the fluxing value of an are may make direct smelting more economical.

Jan 1, 1936

By R. W. Huber, R. C. Wiley, V. C. Petersen

"Three arc- melted ingots, two of a t itanium-7 percent manganese all oy and the third of unalloyed titanium, were forged and rolled into 3/ 4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties.These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots.INTRODUCTIONArc -melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Perk, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.Considerable data have been published recently on constitution diagrams and properties of titanium-manganese alloys in genera1. 3/ 4/5/6/ However, little if any correlation between processing schedules and end results has been published, particularly with respect to the present commercial production of the proprietary titanium manganese alloys . Several factors in the production of titanium and titanium alloys have a pronounced influence on the physical and mechanical properties of the finished product: (1) The degree and nature of impurities in the base materials, ( 2) the amount of impurities introduced during the melting cycle and their distribution, (3) the homogeneity of the alloy, (4) forging, (5) rolling, and ( 6) final heat-treating cycles. All of these item£ are important from a metallurgical standpoint in producing the desired end properties in the metal."

Mar 1, 1955

By W. W. Adams

"Accidents at coal mines in the United States in September 1926 resulted in the loss of 170 lives, according to information furnished to the Bureau of Mines, Department of Commerce, by State mine inspectors. Of this number 125 occurred at bituminous mines and 45 in the anthracite field. As the bituminous output of coal for September was 48,976,000 tons, and the production of anthracite was 8,444,000 tons, the fatalities reported represented a death rate of 2.55 per million tons for bituminous mines and 5.33 for anthracite mines. The industry as a whole showed a fatality rate of 2.6 per million tons of coal produced in September 1925 the rate for bituminous coal mines was 3.29; the anthracite mines were idle in September last year due to a strike.During the first nine months of the present year 1,759 men have been killed by accidents at the coal mines throughout the United States, resulting in a death rate, per million tons of coal produced, of 3.76 as compared with 3.95 for the same period in 1925. Reports for bituminous mines alone showed a nine-month fatality rate of 3.53 which was about the same as the corresponding rate from January to September in 1925. The anthracite rate for the present year, however, shows a decrease of about 17 per cent; that is, the rate has declined from 6.36 to 5.28.Records covering the first nine months of 1926 show that 12 ""major"" disasters, that is, disasters in which five or more men were killed at one time, have resulted in the loss of 271 lives as against 10 disasters and 199 deaths in the corresponding months in 1925. The fatality rates for these disaster: alone were 0.579 and 0.465, respectively. One major explosion occurred at Tahona, Oklahoma, on September 3, 1926, in which 16 men lost their lives.An analysis of the principal causes of the 1,759 fatalities for the first nine months of the present year shows a reduction in the death rate as a whole and for falls of roof and coal and for explosives, but an increase in haulage, gas and dust explosions, and electricity. The comparative rates for these accidents were:"

Oct 1, 1926

By R. E. Siemens

The Bureau of Mines sought to correlate the variation of structure-sensitive superconducting properties with microstructure in selected Cb-Hf alloys and to compare the experimental results with those predicted by the GLAG theory. Alloys in wire and rod form were evaluated by critical temperature, critical current, magnetization, resistivity measurements, and optical and electron microscopy. In the absence of an external magnetic field, the current carrying capacity of columbium was greatly reduced with addition of up to 85 wt pct Hf, but a large increase in Ic occurred for Cb-90 wt pct Hf. Favorable Ic-H behavior was observed in cold-drawn alloys containing 25 and 57 wt pct Hf. Correspondingly, a maximum in Tc occurred at 10-25 and 90 wt pct Hf. Four- or five-hour heat treatment at 600° C resulted in maximum Ic values and maximum hysteresis in magnetization. Dislocation pileup, polygonization, and fine precipitates, responsible for flux pinning, are listed in order of their effectiveness as pinning sites. Sites having an average separation of 1,500 to 3,000 A and a diameter of 1,000 A or less were most effective in influencing Ic-H and M-H behavior. The resistive critical fields increased smoothly to a maximum of 80 k0e between 60 and 65 wt pct Hf. Highfield, mixed state, reversible paramagnetism was observed in some alloys; however, the GLAG theory was in good agreement with experimental results for the majority of the composition range studied.

Jan 1, 1969

By Joseph A. Sutton, John D. Corrick

The chemistry involved in the microbial dissolution of iron and copper from such sulfide minerals as pyrite, chalcopyrite, chalcocite, cove11ite, and bornite is described. The chemical criteria used to evaluate the activity of microorganisms on these minerals were changes in pH, ferric iron produced, and oxygen consumption. In a series of experiments in which a ferrous sulfate nutrient solution was percolated over small portions of the above-mentioned copper sulfide minerals for 56 days, the iron-oxidizing bacteria Ferrobaci11us ferrooxidans and Thiobaci11us ferrooxidans were capable of bringing about the dissolution of 23.7 percent of the copper from chalcocite, 56.3 percent of the copper from cove11ite, and 29.8 percent of the copper from bornite by the microbial production of ferric sulfate which reacted with these minerals. Laboratory tests have demonstrated that pure strains of the iron-oxidizing bacteria act as catalysts to the ferrous iron being oxidized by the Oxygen of a system containing pyrite and chalcopyrite. In a series of experiments during which nutrient solution was percolated over pyrite for 70 days, the ferric iron produced by the iron-oxidizing bacteria was 112 to 120 times greater than that produced atmospherically.

Jan 1, 1964

By R. V. Ramani, R. Bhaskar

"The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.IntroductionAn airborne dust cloud is a complex system containing particles of varied size, density, shape and state of aggregation. The behavior of the particles is dependent on a number of complex physical mechanisms, often opposing in nature. The net interaction results in the ambient concentration. This size dependent behavior of particles contrasts with that of gases, an area quite widely studied.The term aerosol is used to describe clouds of microscopic and submicroscopic particles in air such as chemical smoke or particulate matter released from smoke stacks. An aerosol system can be regarded as an arbitrary element of volume filled with gas and suspended particles of possible highly variable physiochemical nature. The parameters that are used to describe an aerosol system include concentration, mass average velocity and particle mass and radius. In characterizing such systems, several assumptions are made. Among these is the assumption that particles are smooth, inert and rigid spheres. Again, for example, when the particles are in transport, the possibility of collision exists. As a result of the collision, the particles may coalesce to form larger particles. The probability of sticking is considered a known quantity (lady, 1970). In this paper, the application of the principles used in aerosol systems is explored for the study of the transport and deposition of fine coal dust in underground mines."

Jun 1, 1988

By James S. Browning

The Bureau of Mines conducted laboratory and small--scale continuous tests of weathered mica pegmatite ores from Hart County, Ga., to determine the technical feasibility of recovering commercial-grade mica concentrates by flotation. Two modifications of the Bureau-developed anionic-cationic method were used. In one method, sodium carbonate and calcium lignin sulfonate were used for pH control and quartz depression; this method yielded mica concentrates containing 98.5 percent mica with a recovery of 91.4 percent. In the other modification, lime and sodium silicate were used with the calcium lignin sulfonate; concentrates containing 98.9 percent mica with a recovery of 86 percent were obtained.

Jan 1, 1966

By J. P. Bennett

Based on previous Bureau of Mines research indicating that improved high-temperature properties could be achieved for periclase refractories through chemical additions, the Bureau investigated the properties of full-size bricks produced from chemically modified periclase refractory grains and the suitability of making such chemical additions to Mg(OH)2 slurries prior to production of the periclase grains. In full-size brick testing, strength values, both hot and cold, for the optimized bricks were superior to those for a commercial 98-wt-pct-MgO refractory. The best results were obtained for a natural magnesite with an adjusted CaO:Si02 (C:S) ratio of 3.0 and a 1.0-wt-pct addition of Zr02 and for a seawater periclase with an adjusted C:S ratio of 2.5 and a 0.5-wt-pct addition of Mn02. For samples produced from chemically modified Mg(OH)2 slurries, additions of both Mn02 and Zr02 and an increase in C:S ratios produced significant increases in hot flexural strength, similar to those resulting from chemical additions made to periclase grains. The most effective modifications were additions of Mn02 to brine-derived periclases having a C:S ratio adjusted to 3.0. These results on chemically modified magnesia refractories indicate that such material could potentially substitute for magnesiachrome refractories containing imported chromite.

Jan 1, 1984

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported4/, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simpliication to determine an economically feasible procedure that would require a minimum of expensive equipment for plant erection and a minimum of reagent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth while to utilize available facilities in a search for difficulties that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 pounds per day of metal and operated under simulated plant practice.

Jan 1, 1938

By Suresh K. Bhatt

A mathematically simulated modeling technique is used in this U.S. Bureau of Mines report to represent a hypothetical mining operation with existing mining technology and prevalent mining costs. Mining scenarios were prepared and evaluated for potential benefits and costs available through computer-assisted mining. Base criteria, parameters, and methodology are described.

Jan 1, 1993

By Jr. Smith

To investigate the effects of flow geometry on laminar flames, studies are in progress in this laboratory employing Bunsen-type burners with rectangular cross section. Interpretation of these studies requires a determination of the flow velocity at all points of the rectangular cross section for one dimensional steady laminar flow. In addition, values of the velocity gradient at the boundary for such flows are needed in the interpretation of blow-off and flash-back studies with burners of rectangular cross section. The hydrodynamical problem of steady laminar flow of a viscous fluid in channels of rectangular cross section was solved by Stokes. His results have been quoted by Love21 and by Dryden, Murnaghan, and Bateman,§/ and they have been discussed by Boussines and by Paschoud. It may be noted that the steady laminar flow of a viscous fluid in channels of rectangular cross section constitutes a hydrodynamical analogue for the problem of the torsion of an isotropic prism of rectangular cross section.

Jan 1, 1952

By Arthur V. Petty

The Bureau of Mines has investigated the effect of refractory oxide additions, introduced in soluble form, on the refractory properties of 42-, 58-, and 70-pct-A1203 brick. Brick having porosities ranging from 12 to 16 pct were impregnated with solutions containing chrome, chrome-iron, zirconium, calcium, magnesium, cobalt, nickel, tin, and manganese ions. Additions of some of these ions provided dramatic improvements to such properties as hot modulus of rupture, hot load, and particularly slag resistance. These improvements can be related to reduction of porosity, amorphous grain boundary phases, formation of more refractory bond phases, and reduction of the wettability of Al203-containing refractories by metallurgical slags. Fifty-eight-percent-AI203 brick, impregnated with chrome, showed hot modulus of rupture, hot load, and slag resistance two to five times better than those of untreated 70-pct-AI203 brick. This could result in reducing the Nation's dependence on imported refractory-grade bauxite generally required for high-A1203 brick, as domestic alumina resouces could be used to produce the improved refractories.

Jan 1, 1984

By E. A. Sondreal

The Bureau of Mines investigated the use of lignite char for producing carbon disulfide; CS2 production rates were as high as when wood charcoal was used as raw material. The maximum space velocity for CS2 produced in the bench-scale study was 9,280 hour-1, reacting sulfur and lignite char at 792° C. The reaction temperature and the temperature at which the char was carbonized were the two most important factors in determining CS2 production rates. Increasing the carbonization temperature in nitrogen from 400° to 900° C advanced the temperature at which carbon disulfide was first produced from 550° to 850° C. The average activation energy for reacting chars with sulfur was 44,000 cal/g mole. The reaction was first order with respect to the partial pressure of sulfur. Increasing the rate of sulfur admission caused a decrease in rate of production at otherwise similar conditions. Rates were not affected by either char size or sodium carbonate catalysis. High space velocities at moderate temperatures using inexpensive lignite chars could offer an economic advantage in the manufacture of carbon disulfide provided that yields were attractive.

Jan 1, 1967

By Alfred L. Ransome

The consumption of slab zinc in the United States increased sevenfold in less than a half century since 1900. Therein is reflected the innate characteristics of this versatile and nearly indispensable nonferrous metal whose use has grown at more than twice the rate of industrial production. The total metal consumption was substantially stimulated during the two World War periods, which were likewise marked by notable changes in use pattern accompanied by shifts in geographic distribution. This information circular summarizes basic data collected for many years by the Bureau of Mines, but in particular presents for the 1940-45 period details derived from the comprehensive slab zinc consumption survey inaugurated in 1940. The total consumption of slab zinc has been broken down into four major categories galvanizing, brass products, rolled zinc, and zinc-base alloys -- with minor applications grouped under a fifth heading, other uses. Ex- cept for the inclusion of zinc-base alloys with other uses before 1926, the above-named segregation has been shown for the entire period 1900-45. 11- though a substantial tonnage was taken by all groups in all years, there were large shifts in the use pattern in both World War periods. In both, the Allied Powers depended heavily on the United States for zinc-bearing products, especially those required by war industrius. The departures from usual uses were, however, much more marked during the second than in the first period, mainly because the United States could not have met the tro- mendously expanded war-materiel demands had the greater slab zinc needs of a period of high industrial activity been supplied. The geography of consumption is known in detail only for 1940-45. Even in that short period, substantial shifts are observable, largely the reaction from conversion to war production in 1940-41 and reconversion to peacetime consumption in 1945. However, there is so evidence of other shifts in consumption centers that appear to reflect longer-term develop- ments.

Feb 1, 1948

By John S. Berber

Olefin and paraffin mixtures (C10-C16 and C10-C22) were separated from low-temperature lignite tar by urea adduction and sulfated to yield secondary alkyl sulfate detergents. The C10 ?C16 secondary alkyl sulfate showed a 99.3 percent biodegradability, and the C10-C22 fraction showed a 96.8 percent biodegradability, exceeding the required standard of 80 percent for the biodegradability of anionic detergents in washing and cleaning compounds. Chlorination of paraffins yielded a detergent of 93.2 to 93.4 percent biodegradability.

Jan 1, 1968

By H. R. Hardy Jr., E. J. Kimble Jr., H. W. Shen

"The primary objective of this research project is to study the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. Secondary objectives include the investigation of the acoustic emission technique as an indirect method for coal dust characterization and remote bit wear monitoring. The results of the project will be useful in developing efficient coal cutting techniques which significantly reduce the harmful coal dust components, and in providing methods for remote monitoring of bit condition and associated coal dust character. This paper will outline recent experiments carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. During the experiments acoustic emission and a variety of other mechanical parameters were monitored. · A commercially available artificial intelligence computer package, namely: JCEPAK (Intelligent Classifier Engineering Package), has been utilized to provide a powerful and objective means for AE waveform analysis. This program is able to evaluate a number of features of each AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. Finally, the paper will discuss the results obtained from a variety of coal breakage tests.INTRODUCTIONStudies to date clearly indicate that the reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which will make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit condition and cutting efficiency, and to quantify the particle size and shape distribution of the generated dust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. This paper will outline recent experiments on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. Additional information on these studies are presented elsewhere [4]."

Dec 1, 1996

By James L. Eirls

The objective of this project was to improve a driver's field of view for large trucks used in the mining industry. Rearward viewing was enhanced by improving the rear-view mirror designs. Rear vision was accomplished using a closed circuit television system. Views ahead,, to the right, and downward were obtained with a blind area viewer (BAV). The BAV is a unique combination of fresnel lenses housed in a shielded, environmentally protected enclosure that produces an image of the area in front of and downward 70° and to either side of the BAV 300. The improved visibility devices were evaluated by long-term, in-mine testing. The right Bide mirror (RSM) and BAV provide the greatest improvements for the least cost and are commercially available. Application of the RSM and BAV should achieve a reduction in accident potential and greater vehicle productivity by enlarging and improving the equipment operator's visibility and making priviously blind areas and hazardous situations detectable.

Jan 1, 1982

By Henry P. Cole

A series of studies are described that identify critical health and safety skills needed by underground coal miners for coping with mine emergencies. First aid and self-rescue and escape were selected as two broad performance domains that include many subordinate skills needed for preventing, recognizing, and coping with mine emergencies. The performance domains and their objectives were used to direct the development of simulation exercises that permit miners to experience mine emergencies in the safety of a training room. The exercises are based upon research with similar simulations for the training of flight crews and medical personnel in information gathering, judgment, and decision making skills. Exercise content is drawn from actual mine accident and disaster case studies. The exercises incorporate recent principles of cognitive psychology and instructional design. Initial studies in annual refresher training classes suggest the exercises are stimulating for miners and their instructors, easy to use and read, sufficiently complex and authentic to challenge experienced miners, and useful devices for both teaching and testing critical problem solving skills required for preventing and minimizing emergencies.

Jan 1, 1988