Search Documents

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the Bureau of Mines studied the 350-acre Henry?s Lake Wilderness Study Area (ID-035-077) in order to evaluate its identified mineral resources. The Wilderness Study Area is located in northern Fremont County, ID, approximately 140 air miles north-northeast of Pocatello and 3 miles south of the Montana border. The Wilderness Study Area is near the north shore of Henry's Lake at the foot of the southwest-facing slope of Black Mountain. Archean hornblende gneiss, the main rock type present, crops out northeast of the Madison Range Fault, which trends northwest across the southwest corner of the Wilderness Study Area.

Jan 1, 1988

By Andrew M. Leszcykowski

The Bureau of Mines (Bureau) conducted mineral investigations of the Payette Crest-South Fork area in west central Idaho near McCall, Idaho, in 1989. There are no known producing mines or mineral production from the area. Forty-seven samples were taken (stream sediment, rock. and placer); no identified mineral resources were delineated.

Jan 1, 1991

By Lewis V. Wade

This report provides background information concerning a mine roof simulator currently being considered by the Bureau of Mines. The simulator is a mechanical device with the ability to simulate the forces and displacements associated with mine roof over an area 20 by 20 feet. The topics covered in the report include a conceptual description of the system, definition of system capabilities, discussion of how such capabilities were decided upon, description of available control modes, and a comparison between the mine roof simulator facility and similar facilities existing elsewhere.

Jan 1, 1974

By J. W. Eckerd, W. S. Sanner, P. L. Woolf, R. E. McKeever

The Bureau of Mines experimental blast furnace was operated successfully with anthracite metallurgical briquets . Tuyère pressures were higher and more erratic than for operations using coke , and furnace " hangs " occurred more frequently . Higher hot - blast temperatures were required to maintain the quality of the metal . By using higher hot blast temperatures , the fuel and production rates and slag volumes were comparable to those obtained for all - coke operation . The anthracite metallurgical briquets exhibited excellent mechanical strength and descended through the shaft of the furnace with little breakage or reduction in size .

Jan 1, 1964

By J. L. Stauffer, L. J. Gaydos, L. M. Demers, D. C. Kuhn

"Eicosanoids and cytokines produced by alveolar macrophages (AM) are key mediators of pulmonary inflammation and fibrosis. In order to determine if eicosanoid production and cytokine production are altered in AM obtained from coal miners, we compared production of prostaglandin E2 (PCE2), thromboxane A2 (TXA2), leukotriene B4 (LTB4), interleukin-1 beta (IL-1B ), and tumor necrosis factor alpha (TNfa.) by cultured AM from normal human subjects and coal miners. The recovery of AM from miners' lungs by bronchoalveolar lavage was significantly greater than that from control subjects. Mean eicosanoid and cytokine production by AM from active miners was also increased compared to AM from control subjects, but this increase was not statistically significant. AM from control subjects produced significantly more TXA2 and TNFa. when exposed to lipopolysaccharide than did AM from miners. The cyclooxygenase inhibitor suprofen reduced PGE1 and TXA1 production and TNF0t. release but had no effect on LTB4 production or IL-1B release by miners' AM. The lipoxygenase inhibitor nordihydroguaiaretic acid attenuated TNFa release, as well as that of LTB4, but had no effect on IL-1B release. Inhibition of thromboxane synthase by UK 38,485 also reduced TNFa release by active miners ' AM but had no effect on PGE1, LTB, production, or IL-1 f3 release. The results of these studies suggest that occupational inhalation of coal dust may increase total lung eicosanoid and cytokine levels and reduce the reactivity of AM to bacterial endotoxin. Furthermore, coal dust-induced changes in both eicosanoid and cytokine release may be subject to pharmacological modulation.The alveolar macrophage (AM) is a primary defensive cell in the lung and is one of the first cell types to encounter inhaled mineral dust. The response of the AM to invading foreign material is designed to enhance the defensive capacity of the lung. However, in the case of occupational inhalation of mineral dust particles, this response may be inappropriate, resulting not in the defense of the lung but in chronic inflammation and fibrosis (Rom et al., 1987; Takemura et al., 1989). The reaction of the AM to chronic mineral dust exposure may involve the exaggerated release of paracrine mediators of lung function, including eicosanoids (oxygenated derivatives of arachidonic acid) and peptides, including cytokines and growth factors (Sibille & Reynolds, 1990). Eicosanoids are involved in bronchial and vascular smooth muscle reactivity, vascular permeability, fibroblast growth, and the recruitment of additional immune cells to the alveolar space (Barnard et al., 1992; Elias et al., 1985; Scott et al., 1982). AM-derived cytokines such as interleukin-1 beta (IL-1 B) and tumor necrosis factor alpha (TN Fa) have a variety of biological activities including the regulation of fibroblast growth and proliferation (Becker et al., 1989; Libby et al., 1989; Schmidt et al., 1984). Interestingly, in vitro studies with macrophages suggest that the production of cytokines may be linked to eicosanoid production, in particular that prostaglandin E2 (PGE2) may down-regulate IL-1 f3 and TN Foe production by the AM (Bonta et al., 1989; Kunkel et al., 1986; Monick et al., 1987)."

Dec 1, 1996

By R. V. Ramani, J. Qin

"In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration. INTRODUCTIONA detailed experimental study on the characteristics of longwall dust cloud in operating longwall faces has been reported by Ramani, Qin, and Jankowski (1991). The study indicated that there are several important factors whose effects on dust transport in longwall faces need to be further investigated. In an operating longwall face, the effect of these parameters could not be easily isolated as control over the affecting parameters is not readily possible. In a simulated longwall face, however, these parameters can be controlled. Therefore, as a follow-up to the field study, a series of controlled experiments were conducted in a full scale simulated longwall face in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines [Qin, 1992]. Specific aspects which were addressed during the experimental design phase included determining the types of samples to be collected, selecting proper instruments to collect these samples, and developing detailed sampling and time-study plans to correlate the dust concentrations with face activities. Two types of dust--anthracite and bituminous--were used. Dust dispersion rate into the air as well as the source dust particle size distribution were documented. Control was exercised over both air velocity at the face and air leakage along the longwall face. During experiments, the dust source was moved to simulate the shearer movement at operating longwall faces. Detailed descriptions of the design of experiments, experimental results, and data analyses follow in the subsequent sections."

Dec 1, 1996

By H. J. Lechtenberg

This Bureau of Mines report investigates solvent injection as a means of increasing oil production from low-gravity oilfields; thus, wells in two California oilfields that produce from reservoirs having low-gravity oil were injected with highly aromatic solvents to increase their oil recovery. The wells were either allowed to soak or the solvent was circulated for a period of time. In some of the wells, the solvent was followed by a slug of water. The post-stimulation production rate was considerably higher than the prestimulation rate of the wells. Wells in which the solvent was not followed by water showed an immediate increase in oil production, and essentially all of the solvent was recovered. The wells in which solvent was followed by water essentially showed a delay in the increase in oil production, thus indicating a temporary water block. The results show that the production rate is usually increased by the injection of solvent, and the method may prevent early abandonment of marginal producers. Cumulative post-stimulation oil production indicates that cyclic solvent injection treatment can be an economic success.

Jan 1, 1974

By Thomas A. Davidson

The Bureau of Mines Helium Field Operations has developed a method for determining the helium-3 CHe) content of natural gas and mixtures eontaining 0.5% to 100% helium. The helium is preconcentrated by passing samples through anhydrone, a liquid-nitrogen-cooled chareoal trap, and a titanium absorption trap. The mass spectrometer used to analyze the samples is tuned to 3He at mle ::=; 3.016. Hydrogen deuteride (HD+) interference is minimized by the titanium absorption trap and high instrument resolution. Sample measurements are compared with identically made measurements of a gravimetrically prepared primary standard. The method has a limit of detection of 0.15 ppb with a relative deviation of 13% below the 1~ppb level. The relative deviation is less than 7% for gases eontaining over 100 ppb 3He. The helium isotope ratios of natural gases from the Bureau's Tuck-Trigg Dome Red Cave, the Bush Dome Red Cave, and the Bush Dome Brown Dolomite Formations are distinguishable from one another and from the isotope ratio of crude helium produced from the Panhandle-Hugoton Gasfield.

Jan 1, 1990

By RUSSELL S. DAVIES, Andrew Allan, John W. Buch

This is a progress report for the period February 1, 1949, to August 15, 1949, covering experiments with lightweight shearing machines for developing thin, steeply pitching anthracite beds. The over-all objective at the time an underground test section was established on July 30, 1946, was to improve mining above the gangway by developing methods for mechanization of pitch mining. Following the preliminary cutting tests in the gangway with the German machines, it became evident that the use of machines of this type indicated advantages for development work that could not be overlooked and warranted investigation. An agreement was reached with the cooperating company that this be done. Thus, the objectivo in the period covered by this report has been to obtain operating data to uso in comparing hand and machine methods of driving development openings. In obtaining the machine-mining data, 78 feet of gangway, 108 feet of heading, and 80 foot of chute work were driven. Hand-mining data are authentic for the mining condition. It has been shown that full mechanization is two and one-half times as fast as conventional hand methods on a lineal-feet- advance-per-shift basis and costs but little more than one-third as much. Tho machines are air-powered; there is less shattering of the coal bed by blasting; water sprays are used to allay' dust; coal is loaded by machine; no rock is taken; timber is not dislodgod by heavy blasting charges; and it may be said, except for the development of a means for transporting timber to the face, that the tasks for the miner are less arduous, and the working face equally as safe, or safer, than in driving by hand. Face timbering remains the greatest time- consuming cycle item, and steps are being taken to correct this. More than 50 percent of the cycle time is now usod for face-timbering work.

Jul 1, 1951

By Yael Miron

Two recent unplanned detonations occurred during blasting operations in sulfide-bearing ores in a Nevada gold mine. Other premature detonations have also reportedly occurred at other Nevada, California, and Arizona operations within the past few years, with increasing frequency. Unplanned or premature detonations can be extremely hazardous to life and can cause extensive property damage. A miner was injured in one of these occurrences. This report, by the U.S. Bureau of Mines, is intended to acquaint personnel involved in such mining activities with the basic causes for these accidents. These causes include the exothermic oxidation of pyrite (FeS2) and formation of ferrous sulfate (FeS04), the exothermic and energetic reaction of the ferrous sulfate with ammonium nitrate-fuel oil (ANFO)-based explosives, and the associated elevated temperatures that can set off detonators and explosives in the boreholes. Recommendations for safe operation by the Mine Safety and Health Administration, the Bureau, and the mine involved with the recent incidents include monitoring temperatures in the blast holes, analyzing for sulfate and ferrous ions, and limiting the time between loading and firing in accordance with conditions in the blast holes. Other procedures for safe operations should fit specific conditions in, the mines.

Jan 1, 1992

By K. K. Kelley

This report contains heat-content values for hexagonal crystalline germanium dioxide between 298.15° and 1,350° K., and for germanium dioxide glass between 298.15° and 1,800° K. experimentally determined by the Federal Bureau of Mines. No similar data for these substances are to be found in the literature. The heat-content and corresponding entropy-increment data are presented both in tabular form and by equations. Free energy of formation values are estimated for germanium dioxide glass at 298.15° and 1,800° K.

Jan 1, 1961

By Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test-was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health or the Mine Safety and Health Administration.

Jan 1, 2006

By D. Harrington

Research in connection with occupational diseases, including silicosis or, more definitely, pneumoconiosis, has been prosecuted much more actively in North American countries during the past 5 or 10 years than in any other known period. This applies particularly to the United States, owing largely to the fact that in recent years compensation for ill health presumed to be caused by industrial work of certain kinds is being paid to a far greater extent in this country than previously. Most other countries have had occupational-disease laws for many years. Court rulings in the United States, which started 5 or 6 years ago, have given a few heavy verdicts in connection with ill health or death caused, or alleged to have been caused, by some phase of occupational work other than traumatic injury, and these have called attention to the fact that ill health and even incapacitation can be caused by some kinds of employment. With the onset of the world-wide financial depression, which resulted in permanent abandonment of many business or industrial enterprises (among them mines) in the United States, the workers frequently believed that they could expect nothing in the future from their former employers, hence they felt free to demand monetary benefits or damages because of ill health which they suffered, or thought they suffered, because of their previous employment. The result was a flood of lawsuits and. compensation claims for occupational disease, particularly where dust was involved.

Jan 1, 1938

By Welby G. Courtney

The Bureau of Mines conducted an exploratory field survey to determine the amount of airborne coal dust, the size distribution of the dust, and the rate of dust deposition in coal mine airways. The survey was taken at eight underground locations in operating coal mines. The rate of dust deposition in the airways depended upon the concentration of air-borne dust and decreased exponentially with distance from the dust source. The rate was seemingly independent of the size of the airborne dust particles. The rate of deposition, along a return, for the coal dust from a fade being mined with a continuous mining machine closely matched the rate for the rock dust from a trickle duster. A sample rock-dusting schedule for that return is presented; that is, the trickle duster should be operated for 3-112 hours after every five shifts to protect the average deposit of new float coal dust in the return, but operation after every three shifts is preferred, to protect an occasional heavier deposit.

Jan 1, 1982

By Robert C. Bates

This Bureau of Mines report converts published data on the cost of ventilating uranium mines to a common price base and analyzes these data to determine the cost per ton of uranium ore at various levels of radiation exposure control. There appears to be an exponential increase of cost as the radiation level is lowered. The 1967 base costs are extrapolated to present dollars, and some cost comparisons are given for other radiation control measures.

Jan 1, 1981

By George S. Rice, J. W. Paul, E. H. Denny

Data assembled by the Bureau of Mines , coupled with requests from coal companies , have emphasized the desirability of establishing standardized specifications for brattice cloth with particular respect to durability and fireproofing . Brattice cloth is a canvas or other material , often covered with some fireproofing composition , which is used extensively in coal mining for temporarily deflecting air into pillar workings and maintaining ventilation at the working faces . These specifications will be established , it is planned , through a cooperative program in which the U. S. Bureau of Standards will make a series of tests of various brattice cloths treated with respect to fire- resisting qualities and the U. S. Bureau of Mines will continue to assemble field data on the use of brattice cloth . Plans now are being made for this cooperative work. Without attempting to make a complete survey , the Bureau of Mines has made preliminary studies and investigations , and verious representative coal - mining companies have furnished detailed information . The information thus gained will be used as the basis for the cooperative investigation , but the Bureau of Mines would welcome additional information from mine operators on the character and weight of brattice cloth , conditions of use , durability , quantity employed and price . Such information should be sent to the Director , Bureau of Mines , Washington , D. C. The mine operator is interested in procuring at reasonable cost a brattice cloth with lasting fireproofing quality and of as great durability and strength as possible . There has been a lack of assembled data and knowledge regarding the subject , but the Bureau of Mines feels that this lack of knowledge may be overcome if the coal -mining companies will lend their hearty support to the cooperative investigation and submit information relative to the use of brattice cloth in their own properties . Information contained in this report is based on data obtained from coal operators in bituminous districts of Pennsylvania , Alabama , Utah , Indiana , Illinois , Colorado and Nova Scotia .

Feb 1, 1923

By M. M. Barr

Rapid expansion of the titanium-metal industry focused attention upon ilmenite as a possible substitute for the more expensive and less abundant rutile in producing titanium tetrachloride. Most of the rutile available for this use is imported. Preliminary studies were undertaken to determine the chlorination characteristics of high-titanium slags produced by electric-arc furnace smelting of alluvial Idaho ilmenite at the Federal Bureau of Mines Northwest Electrodevelopment Experiment Station, Albany, Oreg. Low silicon, calcium, and aluminum contents of the slags enhanced their potential value for chlorination.

Jan 1, 1958

By R. V. Higgins

This report presents the results of a study of water injection in the HX sub-pool fault block V-B, in the Upper Terminal zone, Wilmington field, California, and is based on data obtained to May 1957. An earlier report3/ describes the results of gas injection in part of the field. The principal purpose of the pilot flood was to determine whether a sand having a permeability of 1,200 millidarcys and containing oil having a viscosity of 17 centipoises could be waterflooded effectively. The results of a preliminary study by engineers of the Long Beach Harbor Department of oil recoveries from areas where encroaching edgewater was active and the results of an independent study by a consultant retained by the Long Beach Harbor Department were favorable to a trial waterflood. After these preliminary studies, a detailed petroleum-engineering exam-ination was made of the technical details. As a result, a peripheral flood was started in June 1953. The peripheral flood was deemed desirable because the producing wells are bottomed a short distance from the edgewater. The HX subpool was selected for the pilot test because it is an isolated section of the Upper Terminal zone and is separated from the adjoining pools by faults on the east and west and by edgewater on the north, south, and west. Several petroleum-engineering methods were applied to evaluate the performance of the waterflood, and all showed that injecting water stimulated oil production.

Jan 1, 1958

By M. H. Stanczyk

The Bureau of Mines made bench-scale laboratory tests on a sample of typical Florida phosphate slime to determine alumina and phosphate extractions obtainable by agitation leaching, by baking and curing, and by a leach-electrolysis scheme. Recovery of mineral values from leached slime pulps by resin-in-pulp ion exchange contact and the reaction of the leached pulps to filtration, flocculation, and settling were also investigated. The best extractions of alumina and phosphate were obtained by (l) agitation leaching with sulfuric, hydrochloric, or nitric acid at an elevated temperature or (2) curing or baking the slime with sulfuric acid. Alumina extractions ranged from 80.8 to 90.0 percent and phosphate extractions ranged from 93.3 to 98.4 percent when the slime was leached at 90° C with sulfuric, hydrochloric, or nitric acids. Baking the slime with sulfuric acid at 200° C for 4 hours yielded an alumina extraction of 92.3 percent and a phosphate extraction of 97.0 percent, whereas curing with sulfuric acid at 100° C for 24 hours gave slightly higher alumina and phosphate extractions. Flocculation and settling properties of the slime were virtually unaffected in all cases. Filter area requirements, although somewhat improved as compared to untreated slime, remained relatively high. The lowest filter area requirement obtained was 44 square feet per ton of dry solids treated per day. Contacting leached slime pulps with ion exchange resins depleted the leach pulps of solubilized values; however, the filtration and settling properties of the barren pulps were unaffected. A leach-electrolysis scheme resulted in some concentration of solubilized phosphorus, but the method showed little promise of being commercially feasible.

Jan 1, 1966

By Leslie H. Sharp, Martin J. Gavin

Those of the oil-shale operators in this country who are sincerely attempting to make a real industry out of oil-shale developments, are anxious to obtain fundamental data on the retorting of oil-shale; particularly as regards the effect of certain variable factors in the process of retorting on the quantity and quality of products yielded from oil shales when they are subjected to destructive distillation. From careful examination of a con siderable number of suggested processes for treating oil shales and the con flicting ideas on which they are designed, it seems probable that accurate information of a fundamental nature is highly essential to the successful establishment of an oil-shale industry in this country. . Accordingly, the United States Bureau of Mines, in cooperation with the State of Colorado, is undertaking to furnish some definite and impartial information of this type through investigations now under way at the University of Colorado, Boulder, Colo. A retort for the distillation of oil from oil shale has been designed and installed, together with the necessary auxiliary equipment for controlling and determining variable factors of distillation, and for recovering and de termining the quantity and quality of the products yielded from the shales. The retort is of such a nature that conditions of retorting can be accurately . and completely controlled, and varied at will. It is not designed as a com mercial retort, but only for research purposes. A testing laboratory with equipment necessary for the examination of the shales, physically and chemic ally, and the products yielded by them, has also been fitted up . The material used in the investigations is oil shale obtained from the DeBeque, Colorado, shale field. It yields on distillation in the Bureau of Mines testing apparatus, about 42 gallons of oil to the ton, and is there fore a fairly representative sample of the shales that probably will be first worked in Colorado. The shale used will be as uniform as possible in character and oil yield and will all be obtained from the same seam at the same point, in order to avoid the introduction of unnecessary variable factors in the tests and to render results strictly comparable •

Jul 1, 1920