Search Documents

By Parviz F. Rad

The Bureau of Mines conducted rock-cutting experiments under constant normal force and constant penetration in an effort to correlate laboratory data with those obtained in the field. Both independent and interacting groove spacing regions were studied, and optimum and critical cutter spacings were determined. For the laboratory work, the effects of specific energy, muck weight, groove depth, cutting coefficient, and size distribution of the muck for both independent and interacting grooves were studied. For field operations, forward thrust, torque, advance rate, and muck size distribution were the parameters studied. Satisfactory correlation is obtained between laboratory cutting results and field performance data.

Jan 1, 1974

By Richard Hammer

Various alternating current (ac) methods can localize faults in mining power cables. Several methods considered by the Bureau of Mines in this report are the Murray loop for short circuits, wherein a bridge provides proportional distance to the fault; capacitance measurements for open conductors; inductance measurements for shorted conductors; phase comparison, high speed recordings of voltage and current in the faulted state are compared with normal voltage and current with the difference being a function of impedance change and impedance change being a function of fault location; and standing wave measurements, detecting the resonance of the length of cable to a fault (either short or open). Portable capacitance bridges are presently available for the second method, and the fourth method is well developed for use on large power distribution systems. Because it utilizes pulses rather than ac, the time domain reflectometer (TDR) method of fault locating was not included in this investigation. However, a comparative evaluation between this versatile method and the Murray loop might prove advantageous in locating high resistance faults.

Jan 1, 1977

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies It discusses the concept of stress, Critical Incident Stress in emergency responders, and intro¬duces the Critical Incident Stress Debriefing (CISD) process. It is suggested that in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers and more universally, to those responsible for developing emergency management plans.

Aug 1, 1998

Legislation and Government Programs.-On February 4, 1977, the Occupational Safety and Health Administration (OSHA) issued its final environmental impact statement on the occupational use of inorganic arsenic.2 The statement examined the ramifications of the original proposed standard published in the Draft Environmental Impact Statement (DEIS).3 The DEIS proposed to limit the exposure of employees to no more than 4 micrograms of arsenic per cubic meter of air as determined on an 8-hour-time-weighted average basis; or a ceiling limit of 10 micrograms of arsenic per cubic meter of air based on a 15 minute sampling period. The purpose of the proposed regulation is to reduce the risk of smelter workers developing lung and skin cancer as a result of exposure. A comprehensive study compiled by the Committee on Medical and Biologic Effects of Environmental Pollutants concluded that "there is strong epidemiologic evidence that inorganic arsenic is a skin and lung carcinogen in man."' In April 1977, the Environmental Protection Agency (EPA) served notice to ASARCO Incorporated that its Tacoma copper smelter and associated arsenic-producing facilities were in violation of State laws which limit sulfur dioxide and particulate matter emissions. This notice followed the Washington State Pollution Control Hearing Board overturning a prior ruling by the Puget Sound Air Pollution Control Agency (PSAPCA) which had permitted a 5-year variance from the State of Washington air quality standards. In December 1977, ASARCO appealed in court the decision of the Hearing Board.

Jan 1, 1980

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory conducted a study of laser safety in potentially flammable environments. Researchers measured threshold igniting powers as a function of beam diameter for butane and propane-air mixtures by laser-heating targets placed on optical fiber tips using a 1064 nm laser. The minimum igniting powers for propane-air and butane-air were about 250 and 300 mW, respectively. Threshold igniting powers for propane-air were approximately proportional to beam diameter for beam diameters from 0.1 to 2.0 mm. Results suggest that relatively powerful beams may be used in these atmospheres without causing ignition, provided the beam diameter is controlled. Threshold ignition delay times using 91125 and 62.51 125 pm fibers were approximately proportional to the inverse square of the laser power. Ignition delays were about 45 ms or longer for laser powers up to 800 mW. Preproduction samples of a commercial optical fuse prevented ignitions under selected test conditions. A self-healing effect was observed for one sample. Comparisons are made with the results of other researchers. O 2006 Laser Institute of America. Key words: propane ignition, butane ignition, laser ignition, nonbeam hazards, fiber optic fuse

May 3, 2006

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

By Stephen A. Hare, O&apos

The melting, casting, and welding of the Raney nickel alloy (42 pct Ni-58 pct A1), a methanation catalyst useful in coal gasification, were investigated. Melting was done in graphite crucibles by heating aluminum and adding nickel using a cryolite slag cover. Casting conditions were found to be optimum when the melt temperature ranged from 1,125° to 1,200° C and the mold temperature ranged from ambient to 250° C. Suitable mold materials were found to be quartz, heat-resistant glassware, olivine, and zircon. Welding of the alloy can be accomplished using tungsten inert gas process. Tensile strength of the alloy, in the as-cast condition, was found to be 2,000 1b/sq in with an impact strength of less than 1 ft-1b. The coefficient of thermal expansion was determined to be 18.4 x 10-6/° C after heat treatment.

Jan 1, 1977

By I. L. Nichols

Laboratory characterization studies have investigated the processing variability of carbonaceous uranium-bearing materials found in-sandstone deposits. This work was conducted by the Federal Bureau of Mines in support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs. Conventional processing produces only partial uranium recovery from these ore materials. Ore samples from New Mexico, Texas, and Wyoming were examined, and each responded differently. Using direct acid leaching techniques, some of the ores required acid additions of only 50 pounds per ton, while others required 300 pounds per ton of material. Maximum extractions ranged from 83 to 94 percent in the six ores tested. Roasting those ores prior to leaching improved extraction of the uranium to the 90 to 99 percent range. An oxidative autoclave treatment used with five of these ores resulted in extraction of 78 to 97 percent of the uranium. The experimental studies also showed that some carbonaceous materials can be concentrated by froth flotation. The flotation tailings were amenable to acid leaching, and up to 98 percent of the uranium was extracted from this type of material.

Jan 1, 1979

By Bruce T. Olenchuk, Wils L. Cooley

Electrical grounding is essential for the safe operation of power systems. A low-impedance path to ground is necessary to prevent the possibility of dangerously high potentials in human work areas. If for any reason this ground connection becomes faulty, a serious hazard may exist. One reason for faulty ground connections is ground bed corrosion. Corrosion of electrical ground rods has plagued the power industry and appeared in coal mine power systems. This paper will investigate ground rod corrosion, its cause, and possible solutions. Included is an evaluation of various ground rods for their ability to resist corrosion under stray current conditions. -The first known study of X-it3 Rod Corrosion is also presented.

Jan 1, 1979

By David S. Yantek, Paul Jurovcik, Eric R. Bauer

Workers in coal preparation plants, where vibrating screens are significant noise sources, are often exposed to sound levels exceeding 90 dB(A). The National Institute for Occupational Safety and Health, a major coal company, and a vibrating screen manufacturer conducted a cooperative study of vibrating screen noise. Rubber isolators reduced sound levels by 1 dB. Urethane screen panels did not reduce sound levels in this case. Drive noise was determined to be the dominant noise source on the screen. Damped side plates reduced vibration levels on the screen sides by 1 to 7 dB(A). Detailed results of the study are presented.

By Barbara J. Halpern

There?s no denying that mining is a male-dominated industry. Yet thanks to technologies developed over the last 20 years, societal changes in sex role stereotyping, individual determi­nation, and the willingness of companies to train women, there are no jobs in mining today where women are not represented. Women are drillers and electricians as well as drivers of heavy equipment and haulpack trucks. They perform jobs ranging from field exploration and metallurgy to clerical and janitorial and warehousing positions, from prospectors and underground blasters to geologists and land reclamation experts, from communicators to legal experts on mining law and more. The Women?s Mining Coalition, founded in 1994 to shepherd responsible legislative mining reform, estimates that 20 percent of the workers in the mining industry are women. Although women are concentrated in clerical and adminis­trative jobs, at least 10 percent are in non-traditional, hardhat jobs, claims the group. There are women in management, but the numbers in senior management remain small, especially in larger companies.

Feb 1, 1998

By J. R. Allsup

The Bureau of Mines studied the characteristics of simulated coal gas as an automotive fuel in two multicylinder vehicles in a standard and high-compression-ratio engine configuration. While using simulated coal gas fuel, increasing the engine compression ratio improved the fuel economy and vehicle performance but increased hydrocarbon emissions by 40 pct. photochemical reactivity of exhaust hydrocarbons was found to be extremely low using the coal gas fuel. An oxidizing catalyst used with the simulated coal gas fuel eliminated all but trace amounts of carbon monoxide and reactive hydrocarbons in the exhaust. Spark gap geometry and firing voltage were varied and, within the range tested, had little effect on vehicle performance and emissions using simulated coal gas fuel.

Jan 1, 1975

By J. H. Russell

As part of its efforts to maximize resource recovery, the Bureau of Mines conducted studies to recover valuable byproducts from Western phosphate beneficiation tailings. Potential byproducts include phosphorus, vanadium, and uranium. The objective was to determine roasting and leaching conditions for maximum dissolution of vanadium from tailings containing approximately 13 pct P205 and 0.23 pct V. Sulfuric acid leaching tests were conducted with the tailings either as a dilute suspension dried, or in a roasted condition with or without NaCl added during roasting. More than 90 pct of the vanadium was dissolved by roasting at 850° C for 120 min with 8-pct NaCl and leaching at 75°C for 120 min with an excess of 2N H2S04, By roasting without NaCl and avoiding the difficulties of the chloride impurity, nearly 80-pct vanadium dissolution was achieved with an 800° C roast for 180 min. Quadratic regression equations were derived to relate vanadium dissolution to roasting and leaching conditions.

Jan 1, 1982

By W. E. Lamont

The Federal Bureau of Mines conducted research to develop methods of removing phosphorus from the earthy, calcareous hematite ores of the Birmingham, Ala., iron district while simultaneously improving the grade and recovery of the iron values prior to furnacing. An attempt was also made to identify the phosphorus minerals present in the ores. The ores contained about 36 percent iron, 12 to 16 percent CaO, 15 to 20 percent hydrochloric acid insolubles, and 0.30 to 0.36 percent phosphorus. Fractions containing 5 to 15 percent phosphorus were isolated from the ores. Collophanite, Ca3P2O3?nH2O, a member of the apatite group, was the only phosphate mineral identified. Beneficiation methods using flotation and reduction roasting with magnetic separation yielded good grade iron concentrates, but were not as effective for reducing the phosphorus content of concentrates. Reduction roasting followed by fine grinding, magnetic separation, and acid leaching gave iron concentrates containing 62.5 percent iron and 0.04 percent phosphorus with an iron recovery of 82.9 percent and a phosphorus rejection of 93.7 percent. Reoxidation of reduced magnetic concentrates followed by acid treatment gave iron concentrates containing 58.1 percent iron and 0.02 percent phosphorus with 89.6 percent recovery of the iron and 96.5 percent rejection of the phosphorus.

Jan 1, 1973

By Ronald S. Conti

Fire is a major concern for those who work in underground mines. A mine fire can occur at anytime and often results in a partial or total evacuation of mine personnel and could result in the loss of lives. Therefore, having a workforce that is well trained to prevent, detect, and fight a fire is important. This paper focuses on responders’ preparedness for fire. Responders in this context are considered the entire workforce and are categorized as first, second, and sustained responders and evacuating miners. Quality training enhances ones awareness of mine fire hazards and promotes self-confidence in combating fires and responding to emergencies. Early warning systems and other escapeway aids such as a through-the-earth signaling and communication system, lasers and strobe lights are also addressed. The technological advancements that have been made can improve the state-of-preparedness for responders to underground emergencies and increase the chances of survival for escaping personnel.

By Gregory J. Chekan

In This Chapter [Drilling, blasting, and crushers Diesel particulate Enclosed cabs Ventilation with jet fans Stopping construction methods Propeller fans as main fans] This chapter explains how to control dust in large-entry stone mines, including both silica dust and diesel particulate. Most stone mines are limestone mines, but a substantial minority are marble, sandstone, and granite mines. These mines differ from most others in that entry widths are 30 ft or more and entry heights are 25 ft or more. Such mines, developed with room-and-pillar methods, have large open areas that can make ventilation and dust control more difficult. Because of the difficulty of ventilating stone mines, improved ventilation is a major focal point of this chapter. However, the chapter also covers the control of dust from drills, blasting, and crushers. Another part of the chapter covers enclosed cabs, an effective dust control technique for some workers. BACKGROUND The major dust compliance problem in stone mines is caused by silica (quartz) in the rock. Mines in high-silica rock, 8% or more, are far more likely to have a dust problem than those where there is less silica. Geographically, the limestone in the Northeastern and South Central United States has higher silica than the rest of the country. Chekan and Colinet [2002] have analyzed Mine Safety and Health Administration (MSHA) dust sampling results [MSHA 2001] from the stone industry. They have concluded that, on average across the United States, the workers exposed to the highest dust concentrations are rotary drill operators, front-end loader operators, truck drivers, and crusher operators. However, there are many regional differences. Also, occupations that work outside of cabs, such as blasters, roof bolters, and laborers, can be exposed to high dust levels.

Jan 6, 2003

By Terry J. Close

In 1992, as part of the U.S. Bureau of Mines Idaho Land Assessment Program, the Western Field Operations Center investigated the mineral resources of the 30,300-hectare Elk Summit study area. The area is in the Clearwater National Forest, adjoining the Selway-Bitterroot Wilderness in Idaho County. Idaho. The study area is underlain by granitic and metasedimentary rocks. Associated with these rocks are road metal (stone) resources, black sand mineral placer resources, and thermal water resources. Also present are abundant sand and gravel. Two of the five sites examined during the Bureau study have road metal (stone) resources, one has black sand mineral resources, one has thermal water resources. The fifth site is a black sand mineral placer occurrence. There is no evidence of petroleum or coal resources. Idaho County records indicate that 38 mining claims, mostly black-sand placer, have been located in the study area, Twenty-three of the claims are current. Workings consist of a few pits and trenches at the placer, and two borrow pits. The only mineral commodity produced from the area was about 1,500 tonnes of stone excavated from the Savage Pass and Swamp Creek borrow pits along the Elk Summit road, north of Hoodoo Lake. The stone was used to surface the road; these stone resources will continue to be used as needed.

Jan 1, 1993

By C. M. Frost

Crude shale oil produced during in situ retorting by the Bureau of Mines at Rock Springs, Wyo., was refined by three schemes. In the first, the crude oil was fractionated to raw naphtha and 400° F+ residuum. The residuum was hydrogenated over cobalt molybdate catalyst at 815° F and 1,100 psig. The blended raw and 160°-400° F hydrogenated naphthas were hydrodenitrified and then catalytically reformed. The 400° F+ hydrogenated oil was catalytically cracked. In the second scheme, the crude was hydrogenated over nickel-tungsten catalyst at 800° F and 1,500 psig. The hydrogenated fractions were processed by methods used in the first scheme. The third scheme resembled the second but, prior to hydrogenation, the crude was "hydrostabilized" over cobalt molybdate at 500° F and 500 psig. Yields of reformate and cat-cracked gasoline as volume-percents of the crude, and research-method octane numbers (with 3 ml TEL) for the three methods were as follows: First method, 32 pet reformate, 90 octane; 19.5 pct cracked gasoline, 99.2 octane. Second method, 29 pet reformate, 81.1 octane; 21.3 pct cracked gasoline, 99.6 octane. Third method, 28.2 pet reformate, 86 octane; 28.7 pct cracked gasoline, 95.9 octane.

Jan 1, 1974

By D. E. Hirsch

The types of compounds present in aromatic concentrates derived from high-boiling petroleum distillates can be estimated from a gel permeation chromato-graphic (GPC) analysis by the use of tables developed from extensive GPC and mass-spectral analyses on fractions from four crude oils. For a fraction from the GPC analysis, the retention volume and the molecular weights (from mass spectrometer) suffice to indicate the types of compounds which predominate. The tables which show these qualitative analyses were developed through the use of pure compounds as well as the extensive analyses on Prudhoe Bay (Alaska), Gach Saran (Iran), Swan Hills (Canada), and Wilmington (California) crude oils. These tables provide a rapid method for determining which types of compounds are present in a GPC fraction before attempting to develop quantitative data.

Jan 1, 1974

By Richard E. Dawes

Physical variables, a principal factor in the economies of mineral production, affect both capital and direct operating costs. By using a revenue-cost system for the framework, the analyses of revenue and cost categories demonstrate the relative importance of groups of physical variables, whether explicitly defined or not, to a lead-zinc mining operation. Physical variables affecting the producer represent about 60 percent of the total system influence as expressed by cost ranking. Other physical variables affect the remaining costs as controlled by the smelter, the transporter, and the landowner. Such resource conservation aspects as mineral losses due to mining method and mineral processing constitute a portion of the total revenue effects of physical variables. The physical variable revenue-cost system presented in this report offers a framework for cost-benefit analysis of mineral related research.

Jan 1, 1969