Search Documents

By Elton L. Litchfield

The Bureau of Mines determined minimum energies for direct initiation of expanding gaseous detonation waves in acetylene-oxygen mixtures. Composition limit ranges for the initiation of detonation with fixed energies have been compared to data in the literature. Assuming that the stored electrical energy is completely converted to thermal energy, the agreement between the energy of primary explosive initiators and the energy of electrical discharge initiators was good. Minimum energies for initiation of detonation in the most sensitive composition (40 percent C20 plus 60 percent 0 2) were: 0.64 joule at an initial pressure of 1/4 atmosphere, 5.0X10-2 joule at 1/2 atmos¬phere, and 3.7X10-3 joule at I atmosphere. Fuel concentrations in mixtures initiated to detonation by 4.9X102 joules ranged from 10 to 65 percent C2H2 at 1/4 atmosphere, 10 to 67 percent C2H2 at 1/2 atmosphere, and 9 to 68 percent C2H2 at 1 atmosphere.

Jan 1, 1967

By D. W. Frommer

Laboratory mineral-dressing investigations were conducted on talc-bearing samples from Arkansas and Texas under the Bureau of Mines program of examinations and surveys, which is concerned, in part, with the improvement of conservation and utilization of domestic mineral resources. Two of the soapstones in question were successfully upgraded by flotation, utilizing stage additions of a frother and an amine to promote their talc content. The process could enable the producers to meet more rigid specifications of higher priced talc commodities. INTRODUCTION Talc is an industrial mineral with distinctive properties, such as softness, smoothness, large surface area in relation to mass, chemical inertness, and good retention as a filler, that make it particularly valuable to a number of industries. Sales to 6 industries -ceramics, paint, insecticide, rubber, roofing, and paper -consumed 84 percent of the domestic production of talc, pyrophyllite, and ground soapstone in 1952. Mine production in that year totaled 600,908 tons. Sales of crude and ground material were 593,147 tons valued at $11,347,317.2/

Jan 1, 1956

By A. Wahab Khair

"Geologic materials emit transient noises when stressed /1/. The rate and pattern of these transient noises or acoustic emissions (A.E. hereafter) depend on the stages of deformation of the material /2/. It has been demonstrated that rock/coal fracture processes under stress consist of three distinctive stages--crack initiation, propagation and ultimate fracture--and that coalescence of numerous cracks leads to ultimate failure rather than the propagation of a single crack /2,3/. This paper presents an analysis of fracture formation in rock/coal specimens subjected to straight wedge indentors using A.E. technique.The effect of specimen geometry, wedge indentor angle, confining pressure, and material anisotropy on fracture type (tension, extension, and shear crack), fracture length, and fracture intensity were studied. Two types of material mainly Berea sandstone and Coal Berg No. 2 coal were used in this study. Prior to the experiment the mechanical properties of both sandstone and coal were determined using rectangular specimen (Figures 1 a) in standard compression tests and are given in Table 1. In this study cylindrical and rectangular specimens were first prepared to proper dimensions of 2 in. x 1.5 in. and 3 in. x 1.5 in. x 1.5 in. (5.08 cm x 3.81 cm and 7.62 cm x 3.81 cm x 3.81 cm), respectively and then instrumented with SR-4 strain gages as shown in Figure 1. The instrumented specimens were then tested under four distinct load boundary conditions as illustrated in Figure 2. During a typical experiment the instrumented specimen was placed in a specially designed loading jig (Figure 3) where a predetermined lateral pressure was applied mechanically to the specimen by adjusting the inner plate of the confining chamber via screw while monitoring strains in the specimen. Using rock/coal elastic constants and measured strains, a predeter¬mined lateral pressure was applied to the specimen. Then a vertical load was applied by the straight edge of a wedge indentor attached to the upper platen of the universal loading machine via ball and socket arrangement (Figure 4). The arrangement allowed uniform application of load in a straight line manner on the surface of the specimen. During the test a number of parameters namely strains, load and A.E. rates were recorded (Figures 5a-b)."

Jun 1, 1988

By H. S. Chiang, S. S. Peng

"SummaryAir velocity distribution surveys on four mechanized longwall faces are presented and discussed. Although there are discernible patterns in the velocity distribution, there are wide differences in distribution in the cases examined. This can be attributed to differences in mining and face geometry. An important factor is air leakage into the goaf.IntroductionOver the past two years several intensive air velocity surveys have been carried out in West Virginia coal mines as part of a programme aimed at understanding dust transport mechanisms on mechanized longwall faces. These are presented here and some of the patterns of velocity distribution are discussed.Ventilation survey methodologyThe air velocity vector consists of three mutually perpendicular subvectors; the vertical subvector is directed toward the roof, one of the horizontal subvectors is parallel to the coal face and the other pointing to the gob. The air velocity which was measured in this paper is the horizontal subvector parallel to the coal face.To record the velocity distributions at the longwall faces, the surveying stations and the surveying points were established as follows.(1) The first station usually was set at the third support from the headentry T-junction. Within the first few supports, the air coming from the intake airway encounters a sharp right-angle turn at the T-junction, and forms a turbulent region close to the coal face. The intake air in this region is also influenced by the motors that drive the face conveyer. But when the air reaches the different. But for the same face the number was the same. The main air-travelling area was divided into six to 12 equally sized sub-areas, and each surveying point was situated approximately at the centre of the sub-area.The velocity survey was carried out by two persons, one reading the meter and the other taking down the readings. A complete survey at one station took about 5-8 min. Usually, the dimension of the cross-sectional area was measured during that time.A third person used the smoke tubes to observe the following: (I) the air movement patterns at different locations; (2) the extent and the direction of the air leakage; and (3) the machines' influence on the main airflow. At the same time he observed and recorded the roof conditions and the compactness of the roof-caving in the gob."

Mar 1, 1989

By W. L. Cornell

The Missouri Pb ores are the only domestic Co resource being mined and processed for other metals; therefore, they present a viable short-term opportunity for Co production. Lead, zinc, and copper concentrates are produced from the ore. The Cu concentrate can contain up to 30 pct Co and the Pb concentrate up to 15 pct Co. Since Co is detrimental to the processing of the Zn concentrate; the remainder of the Co is rejected to the tailings. The tailings can contain as much as 50 pet Co originally present in the mined ore. Researchers at the U.S. Bureau of Mines have successfully tested on a continuous basis a process that recovers a bulk sulfide concentrate from mill tailings. The concentrate contains up to one-half of the Co and from 50 to 90 pct of the Pb, Zn, and Cu. Concentrate weight represents 10 pet or less of the total tailings.

Jan 1, 1989

By E. F. Ferrell

Gold was recovered from scrap electronic 60-40 (tin-lead) solders by drossing with aluminum or zinc at elevated temperatures. The gold, together with other metallic impurities, collected in the dross phase which could then be separated from the molten solder by skimming or filtering. Drossing upgraded the gold concentration by a factor of 10. Further upgrading was achieved by a combination of steps including an oxidation roast and either a combined cyanidation-amalgamation treatment or an aqua regia leach. The gold was then recovered in highly concentrated form from the aqua regia or cyanide solutions by cementation and from the amalgam by volatilization or dissolution of the mercury. The solder was purified by reaction with NaOH to remove dissolved aluminum or with SnCl2 to remove dissolved zinc.

Jan 1, 1976

By D. Caruso

The health and financial costs of cumulative injuries are plaguing the mining industry. Industry leaders are concentrating on reducing the risk of injury to their workers through design and redesign of work environments. While ergonomics is not a currently regulated field, many mines are realizing that the only way to tackle their most costly injuries, cumulative injuries, is to make the proactive choice to understand those injuries, their root causes and to make workplace changes to prevent them from occurring. Reduction of these injuries not only improves the health and morale of the workers but increases productivity and profit for the companies. Knowledge and reporting of ergonomic risk factors by employees and ergonomics committees is key to these changes and to the reduction of cumulative injuries. NIOSH is developing strong relationships with industry associations and equipment manufacturers to leverage their communication abilities to transfer knowledge to their customers and make a difference in the health and safety of U.S. miners. The benefits of a formalized approach to reducing these injuries along with examples will be presented.

By R. L. Grant, R. W. Van Dolah, N. E. Hanna

An experimental investigation was conducted to assay the relation between natural gas concentration and ignitibility of the gallery atmosphere . Both the gas concentration representing maximum ignitibility and the relationship between certain properties of the explosives and their incendivity are discussed . The data show that variation in the natural gas content in the gallery can have a highly significant effect on ignitibility of the gallery atmosphere ; maximum ignitibility of the atmosphere by permissible explosives occurs with approximately 8.1 percent natural gas . The study also shows that incendivity of a permissible explosive cannot be determined only by its detonation velocity , oxygen balance , or ballistic mortar strength . However , for similar type explosives , trends observed indicate that their incendivity increases with detonation velocity or bulk strength . Additionally , for underoxidized explosives studied here , the more negative the oxygen balance the less incendive was the explosive within a class defined by salt content .

Jan 1, 1963

By J. F. Barkley

The following questions and answers were prepared principally to supply information in answer to general inquiries received by the Bureau from those contemplating the use of propane and butane fuels . Primary or basic information only is covered; this usually gives enough guidance for most inquirers . To those who wish information of the treatise type , the handbook , Butane- Propane Gases , published by the Jenkins Publications , Inc. , 1709 West 8th Street , Los Angeles 14, Calif . , is suggested .

May 1, 1949

By T. A. Henrie, D. C. Fleck, D. G. Kesterke

Uranium metal was electrowon from uranium dioxide dissolved in fluoride melts . The UO₂ was fed directly to the cell in a continuous manner . Electrolysis was performed at 1 , 200 ° to 1,300 ° C in electrolytes composed of UF4 , LiF , and BaFa . A single regulus of metal was collected in a confined area of the crucible . Product purity of 99.8 percent was attained . Carbon was the major contaminant . Compartmented cells were studied as a means of confining the oxide feed to the vicinity of the anodes .

Jan 1, 1964

By Jr. Hardy, H. Warren Shen

"A study is presently underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal breakage and cutting procedures. The present paper will focus on the test facilities, experimental techniques, and results associated with linear, single-bit cutting. An AE-transducer, attached directly to the bit, detected AE signals during the cutting process.Experiments have been carried out on seven specimens of coal obtained from the USBM experimental mine at Bruceton, Pennsylvania. Three separate cuts were made for each of two bit angles (10 and 45 degrees) and two bit velocities (0.085 and 0.169 cm/sec), for a total of 12 separate cuts. Data associated with resulting particle size distribution and AE characteristics (major dominant frequency components) will be discussed. Data analysis has also been underway using a computer-based pattern recognition system known as ICEPAK (Intelligent Classifier Engineering Package). This program is able to evaluate over 100 features of an AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. The results to date show that AE generated during some of the test conditions can be recognized by ICEPAK with a recognition rate of 90% and higher while other conditions cannot at present be separated with a suitable recognition rate. Further analysis of the experimental data is presently underway.The reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust, and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit conditions and cutting efficiency, and to quantify the particle size and shape distribution of the generateddust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. To date experiments have been carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. A brief outline of the overall study has been presented in an earlier paper (Hardy, Shen and Kimble, 1995). This paper will consider the linear single-bit cutting studies in more detail.It is generally accepted today that most solids emit low-level seismic signals when they are stressed or deformed. In this paper this phenomenon will be referred to as acoustic emission (Hardy 1972, 1981, 1989). In essence, the measurement of AE activity in a field or laboratory structure is relatively simple. A suitable transducer is attached to the structure, the output of the transducer is connected to an associated monitoring system, and the AE signals occurring in the structure, due to internal or external stress, deformation, and failure are suitably acquired, pre¬processed and recorded."

Jan 1, 1998

By K. D. Luxbacher

Understanding methane emissions in underground coal mines is critical for a safe and productive mine. In addition to reasonable estimation of initial coalbed reservoir parameters, it is also crucial that changes in effective stress due to mining and pore pressure reduction are taken into account due to their effects on porosity and permeability. Primary parameters for estimation of emissions or modeling of the mining environment for this purpose are porosity and permeability which can change dramatically as a result of stress redistribution associated with mining and gas desorption from a large coal volume. These parameters affect the emission rates and ventilation requirements, as well as water inflow into the working environment. Stopping leakage, on the other hand, is a secondary stress dependent factor in estimation of emissions, as convergence of the roof and floor strata, compromising the integrity of the stopping, may result in leakage, making prediction of ventilation requirements difficult. This paper aims to examine the effects of porosity and permeability changes of the coal seam on methane emissions in an underground continuous miner section. The models were developed and executed in a dynamic fashion to simulate an advancing section. Through this process, the changes of effective stress in coal, particularly their change paths, on porosity and permeability were incorporated into the models and methane emissions, concentrations, air requirements, water inflow and possible leakage from the stoppings were investigated using a conventional coalbed methane reservoir model.

Jan 1, 2009

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010

By Carlton E. Brown

In 1935 , Brown and Yant / described a microprojector ( microscopic arrangement for projecting images on a screen ) for use in counting and measuring the size of dust particles in Owens - jet dust - counter and simila dry samples of dust collected from the air . In 1938 Brown and others , described a modification of this microprojector that could be used also in counting dust in impinger samples . Microprojectors of this second type have been set up by many mining companies and others and have been made commercially available . Hamly and Pullen5/ described a modification of this microprojector for use in making rapid comparative estimates on konimeter samples and other determinations . This report contains information on still another modification named the "midget microprojector " because of its small size .

Sep 1, 1944

The question of earth models has repeatedly arisen in our work. An accurate representation of the seismic properties is required for three reasons: 1.To be able to determine from a set of received arrival times, the location of a seismic source in the earth, and secondly the degree of accuracy required in the model used for calculating source location from the set of arrival time differences. 2. To be able to determine the expected arrival times at an array of geophones produced in response to a hypothetical source in the earth. 3. To be able to estimate received signal strengths more accurately. The work reported here on earth models is based on information from sever- al consultants and from others who expressed an interest in the problem and supplied information to us. II. COAL MINE GEOLOGY On one of our earlier assignments for the Bureau of Mines, Earth Science Research Inc. of Cambridge, Massachusetts prepared for us a short description of the lithology to be expected at coal mine sites. This description follows, together with the ranges of compressional seismic velocities (Figure I*) associated with typical materials comprising the layered structure of a coal mine area. Coal is primarily associated with fresh water sediments including sandstones, shales, and clays, and occasionally may be metamorphased to varying degrees. In the Appalachian Basin the coal beds occur within cyclical sequences of non-marine shales, sands tones, conglomerates, limes tones, and clays. The beds range in thickness from a few inches to 60 feet, averaging between 2 feet and 10 feet. They have generally broad areal extent, occasionally up to 5,000 square miles, and have an overall tabular or lens-like shape. Within a particular lens, local changes in thickness are normal.

Jan 1, 1974

By R. Larry Grayson, Douglas F. Scott

Data on health-related illnesses and disease in the mining industry are scarce, and information on rates and costs is not readily available. Substantial amounts of research are being directed to addressing these issues, including work at the National Institute for Occupational Safety and Health’s (NIOSH) mining health and safety laboratories in Spokane and Pitts-burgh. This paper briefly discusses the current status of some miner health-related issues, including those involving coal dust, silica dust, diesel particulate matter, asbestos, noise, lead, welding fumes, and skin disorders, as well as research and other activities aimed at protecting miners from occupational illnesses and disease.

By H. W. Lang

The Bureau of Mines conducted an investigation to observe the effect of cetane improvers upon nitrogen oxides concentration in diesel exhaust gas. Amyl nitrite and amyl nitrate were used as additives to the fuel used in a four-cycle, single cylinder type test engine. It was concluded that nitrogen oxide concentrations were not enhanced at fuel-air ratios above 0.03 pound of fuel per pound of air.

Jan 1, 1969

By Roy F. Abernethy

This report describes a method developed by the Bureau of Mines for the determination of beryllium in coal ash. Samples are put into solution by standard wet chemical procedures. Interfering elements are complexed with Na2EDTA, and the beryllium is separated by extraction of its acetyl acetone complex with chloroform or carbon tetrachloride. Final determination is made with Beryllon II.

Jan 1, 1970

By R. Sainath, Wils L. Cooley

Continuous monitoring of ground bed resistance is essential to insure a low-resistance path for fault currents, lightning strokes, and electrostatic discharges. This paper explains the salient features of the continuous ground bed monitor and its applications. The importance of a low-resistance path to ground is highlighted. Sample readings obtained with the ground bed monitor are included, and typical applications of this instrument are illustrated. This effort was supported by the U.S. Department of Interior's Bureau of Mines under USBM grant G0144138.

Jan 1, 1979

By George J. Conroy

Techniques for locating trailing-cable faults are discussed, particularly those techniques suitable for use in underground coal mines, which have been the subjects of Bureau of Mines research. The discussion concerns precautions and suggestions for locating faults, rather than detailed descriptions of apparatus.

Jan 1, 1979