Search Documents

Assure fail-safe stopping of a mining vehicle immediately following a loss of electric power. Approach A separate emergency brake system which actuates when electrical power is interrupted, was installed on several mining vehicles and tested in a long-term underground mining demonstration. How It Works Separate, spring-actuated brakes, which press against brake discs, are used to stop the vehicle following power failure. To allow norm al movement of the vehicle, hydraulic oil under pres? sure from the vehicle's hydraulic system is directed to a spring? loaded piston in each emergency brake housing. That pressure causes the piston to compress the spring and relieves the spring pressure against the puck, thereby allowing the brake disc to turn freely. See Figure 1 A. If the electrical power fails or if the machine is turned off, a valve in the hydraulic line to the emergency brakes opens. That valve, shown as ?Solenoid Valve (automatic)" in Figure 1, which is normally held closed by its electrical solenoid while the vehicle is electrically powered, is opened by the spring in the valve assembly. The pressure in the hydraulic line which is connected to the emergency brakes then drops to

Jan 1, 1978

Generate less respirable dust during mining by reducing the clogging and downtime of the water sprays on mining machines, especially on continuous miners. Approach An improved filtering system, having commercially available components, has been designed and tested. How It Works The improved filtering system shown opposite is mounted on the mining machine, where It traps particles of coal and pipe scale which cause most clogging of the water sprays. Water entering the system first flows through a ?Y" strainer, which screens out particles larger than 1/8 inch diameter. Next, the water whirls through a small hydrocyclone. Most of the remaining smaller particles are removed and pass Into the accumulator compartment built into the hydrocyclone. The water also flows through a final filter. This filter catches particles that might pass the hydrocyclone, especially during water spray start-up and shut-down, when the speed of the water flow is not sufficient for

Jan 1, 1976

By J. H. Russell

A mathematical modeling method was developed by the U.S. Bureau of Mines for the prediction of the principal equilibrium species in the solvent extraction of nickel. Models were developed for the extraction of nickel from ammoniacal sulfate and carbonate solutions with commercial oxime extractants. Independent variables in the research were nickel concentration, ionic strength, pH of the initial aqueous phase, and extract ants and their concentrations in the organic phase. Results from laboratory shakeout tests compared fairly well with predictions of the equilibrium concentrations of nickel and pH values. For example, the loading of nickel onto the extractant was predicted on average within ±27 pct of the measured values, and the pH to within ± 0.17 pH unit.

Jan 1, 1991

By Donald O. Capstick

A mineral survey of a 13,525-acre portion of the 21,875-acre Owyhee Canyon Wilderness Study Area in northern Nevada was conducted by the U.S. Bureau of Mines in 1984. Two samples from sand and gravel deposits in the study area contained minor placer gold typical of the Owyhee River area. The gold-bearing gravels are too low grade or of insufficient volume to support commercial placer mining operations. The sand and gravel deposits might have minor local construction uses.

Jan 1, 1986

By Edward Thomas

"HISTORYThe origin of roof bolting as a means of roof support is obscure. During the past 23 years a method was developed by the. St. Joseph Lead Co: at its mines in southeastern Missouri, ranging from occasional use of single bolts with small bearing plates to systematic networks of bolts utilizing continuous bearing plates. Officials of this company are not certain which of its employees suggested their use. Many instances of occasional use of roof bolts have come to light during the past few years in widely separated mining districts, such as in West Virginia, Alabama, Illinois, Colorado, and Wyoming bituminous coal mines, and in Pennsylvania anthracite, Lake Superior iron, and Colorado lead-zinc mines. A few of the known installations have boon in place as long as 40 years.These installations usually were made to supplement wooden timbering in mine openings whore space was constricted, although it had been reported that roof bolting was started as a systematic moans of roof support in at least three instances but was abandoned because the cost of installation was excessive. The extra expense above that of conventional timbering could not be recaptured through economies resulting from increased efficiency, such as would be gained through mechanized mining.Roof bolting was first mentioned in mining literature in an article by W. W. Weige 3/ in Engineering and Mining Journal of May 1943, in which he described the use of bolts with 4-inch channel bearing plates in mines of the St. Joseph Load Co."

Sep 1, 1950

To provide safer and more efficient mine operations by improving the operational performance of underground trolley line communication systems. Approach The dc trolley line provides a convenient means of In-mine communication since it can carry signals to each phone on the system whether the phones are in mine vehicles or in a fixed location such as that of a dispatcher. In many cases, however, the system does not perform satisfactorily. Short communication range, noise, and dead spots commonly interfere with effective communication. These problems are inherent with the trolley line, which was designed to transmit power and not communication Signals. As a power line, the trolley line is connected to rectifiers and feeds many loads such as motors, water pumps, track block lights, etc. Each of these devices represents a low impedance radio frequency (RF) shunt that seriously reduces carrier communication Signals. Performance is therefore often poor and can be improved only if the effects of the various shunts can be reduced. The Bureau of Mines has developed numerous methods applicable to either existing or planned phone systems which can improve communication range and reduce the shunting effects of the various loads.

Jan 1, 1983

To reduce needless paging of persons by all phones in a mine or mill, while retaining all-location page capability. Approach Standard pager phones of any manufacturer are modified to include the option of selective calling and message holding. How It Works All commercial mine pager phones presently rely upon voice paging via a loud-speaker. When a page is initiated, every phone in the system broadcasts the audible voice page, even phones in locations where the desired person could not possibly be. The advantage of this scheme is that whole-mine paging occurs. The disadvantage is that persons soon begin ignoring pages because they occur all the time, and most are for someone else. Also, it requires considerable battery power from all phones making it necessary to change batteries very frequently, even in phone locations where personnel rarely go. In addition, if a voice page is made and not heard, there Is no way to leave the message. Therefore, persons who at a later time come near a phone, have no way of knowing a page was made and was not acknowledged. This results in situations that often have a direct bearing on safety and productivity.

Jan 1, 1980

By Rollien R. Wells

THERE are two recognized methods of recording the state of the metallurgical art. One involves delineation of individual advances reported in the literature. This approach is used effectively in the excellent annual reviews published by some of the leading technical journals and in the technology sections of the individual commodity chapters in this volume. In an effort to more clearly indicate the current trend of metallurgical research and development, the authors of this chapter chose the method of discussing generally selected items of interest brought to their attention during 1959. Since technology cannot be confined by dates on a calendar, most of the items mentioned have been in the process of development for several years. No attempt was made to identify the sources of information used here. Material was drawn from many sources : Nonconfidential correspondence and conversations with authorities of the metallurgical fraternity, papers delivered at technical meetings, and articles noted in the technical press, including particularly Engineering and Mining Journal, Metal Progress, Journal of Metals, Mining Engineering, Industrial and Engineering Chemistry, Chemical Engineering, Chemical and Engineering News, Chemical Week, Materials in Design Engineering, Review of Metal Literature, the Canadian Mining and Metallurgical Bulletin, the Mining Journal (British), and the Journal of the Institute of Metals (British).

Jan 1, 1960

By Paul T. Allsman

THE THREE words, research, mechanization, and automation are keynote words for mining technology during 1962. Basically interrelated, they not only express the major technologic developments in mining but are the signposts pointing out the road ahead. The process represented by each of these words is evolutionary rather than revolutionary, but developments during the past year indicate a climactical stage has been reached in the process of evolution. Mining research has progressed beyond the stage of academic discussion and is a programed activity within the Federal Government,3 the mining colleges,4 and many of the large mining companies.5 Research was a major agenda item at various national and international mining meetings in 1962. A list of these meetings would include such diverse locales as the Workshop and Symposium on Computers and Computer Applications in Mining and Exploration at the University of Arizona in March; and the 5th Rock Mechanics Symposium at the University of Minnesota, in May; the Rock Mechanics Symposium at McGill University, Montreal, Canada, in September; and the Colloquium XIII, International Society for Rock Mechanics, at Salzburg, Austria, in November.

Jan 1, 1963

By John C. Edwards

To have the capability to predict the development of localized spontaneous heating within a porous coalbed that is subjected to forced air ventilation or in an otherwise quiescent environment in which buoyancy develops, the Bureau of Mines developed three time-dependent mathematical models, which were used to calculate the temperature increase associated with chemisorption of oxygen by the coal. In each model, spontaneous heating is driven by an Arrhenius first-order reaction between the oxygen and coal. Two models are two-dimensional, and one is one-dimensional. In the first two-dimensional model, a constant-velocity forced convection airflow is specified; and in the other, buoyant flow is allowed to develop in the absence of forced convection. The third model evaluates the airflow from Darcy's law and a specification of the pressure at the surface of a one-dimensional porous coalbed. Numerical computations demonstrated how each model could be used to predict the onset of spontaneous heating when the porous coalbed was subjected to constraints of an imposed internal heat source or a high- temperature airflow. The effects of particle size and coalbed compaction upon spontaneous heating were examined with the third model.

Jan 1, 1990

By Lawrence L. Davis

This chapter includes tables for 1981 that were not available in time for publication of the 1981 Minerals Yearbook, but does not include corresponding tables for 1982. The value of raw nonfuel minerals produced in the United States during 1982 was estimated at about $20 billion, a decrease of $5 billion compared with that of 1981. The decline in value is the first since 1971 and is the largest percentage drop since 1938. Although the domestic mining industry continued to be troubled by difficulties in attracting capital and by import competition from countries with lower overall production costs, the principal cause of the decline was sharply decreased demand brought on by the worldwide economic slowdown. Metal commodities were impacted most severely with only 4 of 21 metals registering production value gains and only 3 of 21 showing production quantity increases. Overall metal production value decreased 37% from that of 1981, a reflection of the domestic slowdown in the automobile and construction industries, which are major metal users, Overall production value of nonmetals decreased 12% compared with that of 1981, with only 14 out of 44 nonmetals showing increases. Nonmetal production quantities increased over 1981 for only 6 of the 44 nonmetals.

Jan 1, 1983

At the present time many coal preparation plants handle coal-clay wastes in one of two methods. In one method, the waste is processed in a thickener, followed by further dewatering through filtration, and subsequent blending with coarse waste refuse from the preparation plant. The resulting mixture is then disposed by stacking it in available storage locations. The coal-clay waste is often reslurried by rain or water from other sources, causing a potentially unsafe situation such as mud flows. The other method often used requires thickening and impoundment of the thickened slurry behind earthen dams which poses safety risks if structural failure of the dams occurs. To overcome these two problems, a flocculation method was developed which produces a stable agglomerated material resistant to reslurrying. How It Works The new method involves treating coal-clay waste with lime to raise the pH and flocculating the slurry with a nontoxic polymer of polyethylene oxide. The resulting floes are dewatered on a static screen and agglomerated. For extremely fine waste, further dewatering of the material is accomplished on a rotary trammel screen. The dewatered material may be ponded or mixed with coarse waste from the preparation plant to produce a stable mixture that can be stacked.

Jan 1, 1985

This report describes magnetic field measurements in the Helvetia Coal Co. Lucene #8 Mine for purposes of deriving a mapping of the magnetic field strength covering the major haulageways which contain conductors. The measurements were performed by Terry S. Cory, P.E. under U.S. Bureau of Mines purchase order P0372716. Assisting in performance of the measurements were personnel from the Bureau of Mines, PMSRC, and Helvetia Coal Co. Acknowledgement is given to Engineer Tom Strong of Helvetia Coal Co. who accompanied the measurement team and who lended support in performing the measurements and in supplying valuable engineering information for use in evaluation of the results. The results of the testing at medium frequency show that coverage of the entire mine area containing conductors can be achieved employing wireless radio techniques whereby radio signals are coupled into and are carried by these conductors. These results confirm earlier qualitative testing of the Collins Mine Wireless Radios in this mine. These results, performed over the frequency range 71-2890 KHz, illustrate the effect of frequency on the radio propagation with the conclusion that the best overall coverage is obtained at frequencies approximating 1000 KHz. This report presents all the raw data and the reduced data in the form of magnetic field strength contour maps. Sufficient information is provided to enable independent reduction of the data. A summary of observations which can be made directly from the contour maps is given.

Jan 9, 1977

Improve the safety, reliability and overall effectiveness of mine stench warning systems and to provide a means of remote control stench injector operation. Approach Industrial gas odorants were analyzed for their suitability for use in mine stench warning systems. A prototype stench injector capable of precise flowrate control was designed, fabricated, and tested using the odorant chosen as having the most favorable properties. Based on the results of the field tests, a second generation injector was developed. The second generation unit features optional remote control operation, and in addition, is simpler to refill and is less expensive than the original injector. A complete second generation system, consisting of two manually operated injectors and one remote controlled injector was in-mine tested through actual mine fire drills. How It Works Ethyl mercaptan mixed with Freon is the predominant stench agent used in the U.S. underground metal and nonmetal mines. However ethyl mercaptan's toxicity,

Jan 1, 1982

Reduce face methane concentrations and help prevent miners from working under unsupported roof while moving the curtain. Approach Use water sprays on the continuous mining machine to move and direct air to the face, and also provide appropriate installation guidelines for the most effective use of the system. I n laboratory tests and under actual mining conditions, the spray fan has proved an effective means of ventilation. Recent observations in the field, however, have shown that not enough technical information is widely available on proper installation of the spray fan. This Technology News is designed to rectify that situation by providing a concise guide for spray fan installation. How the System Works Good ventilation is essential for methane control. The spray fan system repositions regular water sprays to help the normal exhaust face ventilation do a more effective job. The various water sprays help in many ways: 1. Side sprays bring clean air along the side of the miner into the off-curtain corner.

Jan 1, 1983

Reduce the noise levels to which operators of double-drum longwall shearers are exposed without compromising the operational effectiveness of the shearer. The Problem Noise produced by double-drum longwall shearers can be harmful to machine operators. Typical noise levels at the lead-drum operator position range from 100 to 105 dBA, and Federal noise regulations allow only one to two hours of exposure per shift at these levels. Noise radiated by the shearer cutting drum is the primary contributor to the overall noise level. However, test of a noise-controlled cutting drum developed by the Bureau of Mines reduced the operator noise level to 95 dBA, thereby increasing the allowable operating time to four hours per shift. Approach The key design aspect of the noise-controlled shearer drum is its reduced vibration-al response to coal-cutting forces. Laboratory studies have shown that these forces are concentrated in the low-frequency region (500 Hz and below). Since the cylindrical core and the cantilevered I plate-like helix of the standard shearer drum are easily excited by these forces (natural vibration frequencies be-

Jan 1, 1985

By L. A. Haas

The degree of reduction of various silica-graphite mixtures was studied in a batch reactor to determine optimum physical conditions for maximizing the carbothermic reduction of silica. The extent of interaction was determined for reactant mixtures in loose powder and briquet forms at pressures less than 0.01 torr and temperatures up to 1,445° C. Molar ratios were varied from 0.05 to 6.5 with maximum reaction at a ratio of about 1.5. The solid-solid reaction did not appear to involve gaseous intermediates. The extent of reaction better correlated with the number of interparticle contacts than with the true surface area of the reactants. Carbonized dextrose was a better reductant than graphite.

Jan 1, 1968

Provide optimum visibility of mining operations while maintaining protection and comfort for machine operators. Approach A cab with hydraulically powered variable-height control was developed and used on a loading machine in underground operations. How It Works The cab is attached to the vehicle on a horizontal trunnion located near the forward end of the cab. A hydraulic cylinder, controlled by the operator from inside the cab, pivots the cab about the trunnion providing variations of up to 16 inches in elevation. The nominal tramming position of the cab is with its underside 6 inches above the mine bottom. From this position the cab can be pivoted up, or down, so that its back end is elevated 10 inches, or lowered to the floor. (See Figure 1.) The cab encloses the operator for protection against both overhead and lateral obstructions, and it raises or lowers, allowing the operator to select the most advantageous cab height. The cab is angled inboard 30 degrees to the machine line of direction. The operator's seat swivels to allow view of the conveyor during loading. All controls are located within the cab and move up and down with it.

Jan 1, 1978

By L. E. Jackson, E. W. Dean

One of the refining processes to which lubricating oils are frequently subjected effects a reduction in content of paraffin wax. The actual treatment usually involves chilling and filter pressing; the most important result accomplished from a commercial point of view is lowering of the ""cold test"" of the oil. The Bureau of Mines has recently had occasion to ascertain the effect of changes in paraffin wax content upon the viscosity of oil and has conducted a series of experiments described in the present report.Object of the present investigation:The Bureau of Mines has devised and is using a method for the analysis of crude petroleum* which includes determination of the viscosities of lubricating oil distillates. The Bureau method does not provide for preliminary removal of paraffin wax, and it has seemed advisable to determine whether this omission causes any important variation from the results that would be obtained through commercial refinery processing. It was also thought that the present tests, though limited in scope, might be of some practical value in indicating the general effect of paraffin content upon one of the most important properties of lubricating oil.Experimental procedureA five-gallon sample of Pennsylvania crude petroleum was distilled at atmospheric pressure until 50 per cent of the charge had been vaporized. Two liters of the residuum was distilled at a reduced pressure of 40 mm. (absolute) and cuts were separated that came over between the temperature limits of 250° to 275° C. (462° to 527° F.) and 275° to 300° C. (527° to 572° F.). The viscosities of these fractions were determined and they were subsequently subjected to treatment that removed successive percentages of paraffin wax. Viscosity temperature curves were determined for the oil obtained after each removal of wax.

May 1, 1921

By Wm. C. Dean

The location of trapped miners from their seismic signals will be in- accurate if we assume the P-wave propagation velocity is a constant. P- wave velocities are anything but constant in regions about mines, so some calibration is necessary to obtain more accurate seismic locations. The reference event method compares the time arrivals of signals generated by the miners with those previously recorded from a reference or calibration event in the vicinity of the miners. This method locates the miners' position relative to the calibration source. Hence, the location of the miners is absolute if the reference event position is known absolutely, usually from surveys and mine maps. Advantages resulting from the system, besides greater accuracy, are locations independent of the velocity model assumed, the same solution from the full array and from any subset of four or more seismometers in the array (three if the miners' depth is known), fewer seismometers required, and no complex computers required for analysis. VELA Uniform experience shows that the accuracy of locations of teleseismic explosions and earthquakes is improved by an order of magnitude over locations computed from average travel time curves. Each calibration event is applicable only over a limited range. We recommend a field test of the method at a mine to measure its location accuracy, the range of effectiveness for each calibration event, the number of seismometers needed, and the number of reference events required per mine. From these experiments we could decide whether the reference event method was useful and, if so, what form a practical rescue system would take.

Jan 1, 1974