Search Documents

By N. A. Chapman

The effect of using conventional crushing and HPGR in combination with dry or wet milling was investigated using a base metal sulphide (sphalerite), and a PGM (platinum group minerals) ore in order to determine how these different processes affect the flotation performance. In the case of sphalerite, irrespective of the crushing procedure (HPGR or conventional), dry milling resulted in the highest grades and recoveries of zinc. Conversely, in the case of PGMs, a similar treatment produced the poorest results. The results were investigated further by comparing the relative effects of factors such as percentage liberation, particle size, and surface properties of the samples produced by the different milling procedures as well as the concentrates and tailings obtained from the flotation tests.

Jan 1, 2013

By M. J. Nicol, R. P. Colborn

An investigation into the kinetics and mechanism of the oxidation of iron (11) by oxygen in aqueous chloride solutions By R. P. COLBORN Pr. Eng., Ph.D. (Natal) and M. J. NICOLt B.Sc. Hons., Ph.D. (Rand) A reaction mechanism for the oxidation of ferrous chloride by molecular oxygen is developed. and the appropriate constants are evaluated. The effect of a number of cations and anions on the rate of oxidation has been tested.

By J. H. Venter

The accuracy of estimation from samples of ore in bulk By J. H. Venter Published in the Journal April 1972. ERRATA: Equation (1) should read... Equation (3) should read .... line following "Duscussion" Delete" .... Insert... above "References" "Discussion". Replace .... tenth DISCUSSION M. DA VID Professor Venter has proposed a formula to compute the variance of the estimated grade of a lot of broken ore, and interesting comments on the relevance of the formula and suggestions for developments are made by P. R. Janisch.

Jan 4, 1972

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

By C Smit

SYNOPSIS A prototype collimated radiometric face scanner was tested in the Harmony Gold Mine. The results obtained during the pilot study indicate that in situ radiometric uranium assays are statistically indistinguishable from those obtained conventionally from channel chip samples. In addition, the study demonstrated that reasonably reliable gold estimates can be deduced from the radiometric measurements, by use of the ratio of gold to uranium within a mine. The instrumentation, calibration procedures, and background determination are described briefly.

Jan 1, 1985

By D. Van Dyk

Horizontal rotating mills are being used all over the world in different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions that are not always fully understood. Failures are therefore experienced, over time in the industry, which cannot always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyse these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyse the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating and the effect on the fatigue life of the mill gearing components, conditions are better understood, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2006

By А. А. Vasiliev, Y. G. Seredkin, А. V. Aksenov, А. Y. Senchenko

Refractory gold-containing concentrates usually contain gold enclosed in sulphides as well as in rock-forming minerals. Another difficulty is that gold often occurs as very fine inclusions of several micrometres, and even smaller than 1 micrometre, or can be part of the mineral composition at the structure level. Processing of such concentrates is a challenge. Ultrafine grinding and further oxidation are applied for gold liberation. The paper deals with the results from the study of gold deportment using Qemscan, and atmospheric oxidation testwork involving Albion Process™ on a gold-containing concentrate with a high content of refractory gold in sulphides and gangue minerals. Albion process testing was performed at Institute TOMS with the participation of Glencore Technology Pty Ltd (Australia). Additionally, conventional cyanidation testwork was carried out for the concentrate processing. As an alternative technology of gold liberation, oxidising roasting with arsenic stabilisation was used. The results from the study make it possible to assess the efficiency of the above-mentioned methods of gold liberation, and applicability of Albion technology to recover gold from the refractory concentrate. Key words: Gold, refractory concentrate, Albion Process, atmospheric oxidation, oxidising roasting, leaching

Jan 1, 2020

By Christopher J. Oates

Overview ? Mining Codes ? Best Practice ? Mining Standards Guidelines ? Get it right from the start ? External Auditors ? The 5% rule ? MMCRM's - The Key Components ? The MMCRM Report / Certificate ? MMCRM's & Round Robins ? Summary

Jan 1, 2005

By A. F. Khan

The CSense advanced process control (APC) solution?s main objective was to improve the stability of the pH in the first stage leach process thereby improving nickel and iron extraction efficiencies and reducing the base metal (BM) content in the platinum group metals (PGM) concentrate. By improving the stability of the control of the pH on the first stage leach it had the corresponding effect of improving the Ni extraction efficiency by 0.5% and the Fe extraction efficiency by 3.3%. The system relieved the operators of many decisions that were virtually impossible to make given the complex, variable and real-time nature of the processes in their charge. On the operational side, the operators understand the APC system and they trust it. Another benefit is the reduction in pH peaks in the autoclave, which can oxidize certain elements whereby they become difficult, if not impossible, to leach. These elements go right through the process and end up contaminating the PGM solids, with the result that the entire batch has to be recycled through a lengthy and costly processing pipeline.

Jan 1, 2009

Deciding on plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g/t of fresh feed has been assumed a reasonable starting point with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2012

By F. H. Deist, H. D. Small, J. D. Austin, L. F. Duvel

The development and application of a Computer System to aid in the planning of production in mines By F. H. Deist, L. F. Duvel, J. D. Austin, H. D. Small A computer system to aid in the planning of production in mines and its application to a complex colliery are descrIbed, The system consists of three phases, the data base maintenance program the 'production simulator' and the report generation facility, In the first part of the paper the categories of information kept on the data base and the functions of the simulator are described in general terms. The application of the system to a multi-product colliery operating a variety of mining methods in a number of superimposed seams is described m the second part. In conclusion some comments are made on further applications and intended future developments.

1. Mintek publications The folowing are available from Mintek (Private Bag X3015, Randburg, 2125 South Africa) at R35 (including GST) per copy to purchasers in South Africa and US$30 (including airmail postage) to purchasers elsewhere. Report M402 The preparation of synthetic fusion standards for use in the X-ray-fluorescence analysis of rocks and minerals, by RT. Eddy and J.J. Jacobs. Apr. 1990. 19 pp. Report M405 Slag-metal equilibria in the system Fe-Cr-Si-C-Ca-Mg-AI-O, by R.H. Eric and M. Akyizli. Aug. 1990. 29pp. Application Report no. 8 The development of a process for the recovery of gold from gold-bearing solutions by means of activated carbon or resin in a NIMCIX column. 1990. 19 pp. 2. New publications from Trans Tech The folowing are available from Trans Tech Publications Ltd, Old Post Road, Brookfield VT05036, USA. Efect of iron and silicon in aluminium and its aloys, edited by I. Kovacs. 1990. 450 pp. $124. Martensitic transformations, edited by B'.C. Muddle. 1990. 714 pp. $190. Ferites, edited by C.M. Srivastava. 1989. 2 vols. 1280 pp. $254. Properties and characterization of amorphous carbon films, edited by J.J. Pouch and S.A. Alterovitz. 1990. 714 pp. $152. Synthesis and properties of boron nitride, edited by J.J. Pouch and S.A. Alterovitz. 1990.426 pp. $192. Electronic structure and latice defects in aloys, edited by R. W. Siegel and F .E. Fujita. 1989. 320 pp. $78. 3. A new edition Tomorow's materials, by K.E. Easterling. London, The Institute of Metals (1 Carlton House Terace, London SWIY 5DB, England), 1990. 2nd ed. 170pp. US$29. 4. Books for exploration geologists The folowing books are obtainable from Elsevier Science Publishers, P .0. Box 211, 1000 AE Amsterdam, The Netherlands. Lateritic bauxites, by G. Bardossy and G.J.J. Aleva. 1990. 624 pp. DFL. 295. Platinum-group element exploration, by D.L. Buchanan. 1988. 186pp. DFL 150. Lead isotopes in mineral exploration, by B.L. Gulson. 1986. 246 pp. Dfl. 160. Prospecting and exploration of mineral deposits, by M. Kuzvart and M. B6hmer. DFL. 285. 5. Journal for earth scientists . Ore Geology Reviews, published by Elsevier Science Publishers, P.O. Box 211, 1000 AE Amsterdam, Netherlands. 6 issues per year. Annual subscription DFL 453 including postage.

Jan 1, 1990

The Barrick North Mara Mine and the Advanced Systems Group at SGS Minerals collaborated on the implementation of a grinding expert system for the control and optimisation of a single semi autogenous (SAG) mill. Over the last 5 years, grinding expert control has gained wide acceptance by mineral processors. In this paper, two key factors for success are highlighted: the adaptability of the software tools and the interaction with site personnel. Created with SGS?s MET expert console (MEC) toolkit, and running on Gensym?s G2 real time inference software, the North Mara expert logic has been set up to keep a steady and on spec leaching feed slurry while striving to maximize throughput. Leach feed stability was achieved by standardizing operating practices across shifts; a result of successful collaboration with site personnel in developing a consistent control strategy. The strategy maintains the SAG load and power draw in an optimised range by manipulating SAG feed rates and inlet water flow. The project life-cycle was slightly longer than average due to site specific constraints. One of these was the high turnover rate of site?s workforce during the project, coupled with the availability of key staff on site due to the fly in fly out work roster. These constraints called for different, and innovative ways of project commissioning and hand-over. This paper describes details of the control solution, its implementation as well as results and conclusions.

Jan 1, 2009

By K. Koruyan

Although remote sensing technology has been available for many years, it has rarely been used for monitoring mining activity. Recent studies indicate that remote sensing is also a valuable tool for managing and planning certain aspects of the mining operation. In this paper, we examine areal expansion of marble quarries and the affected vegetation over a period of 10 years in the Mugla region in Turkey, using geographic information system (GIS) and remote sensing (RS) techniques. Images captured by ASTER Level 3A01 (3D Ortho Data Set), Landsat 5, and Landsat 7 satellites between 2001 and 2009 were used for the analysis. Changes in the natural vegetation as a function of the production level in the marble quarry were calculated using the normalized difference vegetation index. According to the study results, land cover and natural vegetation decreased by less than 3 per cent and 1 per cent respectively between 2001 and 2009, following an upsurge in mining activity in the region.

Jan 1, 2012

By H. A. D. Kirsten

The structural competence of mesh- and fibre-reinforced shotcrete was investigated in two series of tests on full-scale panels. It was found that uniformly distributed loading was marginally less demanding than point loading, mesh reinforcement was superior to fibre reinforcement, Dramix fibre and Melt Extract fibre were similar in reinforcing characteristics, and 30 mm to 35 mm was an optimum fibre length. Furthermore, the consistency of the fibre content could not be assured on practical mining sites, and an average fibre content of about 1,5 per cent was the maximum that could be obtained for fibre lengths not exceeding 35 mm. Also, owing to its greater flexibility, shotcrete reinforced with diamond mesh was preferable to fibre-reinforced shotcrete in mining excavations subject to squeezing conditions. In view of the difficulties associated with assuring the consistency of the fibre content in mining applications, it appears that the sophisticated attributes of fibre-reinforced shotcrete can be effectively exploited only in civil-engineering applications in which quality assurance is subject to explicit contractual control. Load-deflection curves, together with measurements of compressive stresses in the surfaces of some of the panels, enabled the ultimate flexural strength of reinforced shotcrete to be rigorously formulated, and rigorous design procedures for shotcrete subject to bending and direct thrust to be developed. The application of the procedures is demonstrated in a practical design case in which the moments and thrusts in a tunnel lining are determined in a numerical analysis of the interaction between the lining, the surrounding rock, and the rock-reinforcing system.

Jan 1, 1992

By K. Koruyan

Although remote sensing technology has been available for many years, it has rarely been used for monitoring mining activity. Recent studies indicate that remote sensing is also a valuable tool for managing and planning certain aspects of the mining operation. In this paper, we examine areal expansion of marble quarries and the affected vegetation over a period of 10 years in the Mugla region in Turkey, using geographic information system (GIS) and remote sensing (RS) techniques. Images captured by ASTER Level 3A01 (3D Ortho Data Set), Landsat 5, and Landsat 7 satellites between 2001 and 2009 were used for the analysis. Changes in the natural vegetation as a function of the production level in the marble quarry were calculated using the normalized difference vegetation index. According to the study results, land cover and natural vegetation decreased by less than 3 per cent and 1 per cent respectively between 2001 and 2009, following an upsurge in mining activity in the region.

Jan 1, 2012

By J. Gholamnejad

Determination of the optimum production schedules over the life of a mine is a critical mechanism in open pit mine planning procedures. Long-term production scheduling is used to maximize the net present value of the project under technical, financial, and environmental constraints. Mathematical programming models are well suited for optimizing long-term production schedules of open pit mines. There are two approaches to solving long-term production problems: deterministic- and uncertainty- based approaches. Deterministic-based models are unable to deal with grade and geological uncertainties, which are two important sources of risk in mining industries. This may lead to discrepancies between actual production obtained by these algorithms and planning expectations. In this paper, a new binary integer programming model was developed for long-term production scheduling that incorporates geological uncertainty within the orebody. Then, traditional and uncertainty-based models are applied to an iron ore deposit. Results showed that the uncertainty-based approach yields more practical schedules than traditional approaches in terms of production targets.

Jan 1, 2012

By L. Shoke

The aim of this study was to develop an in-house tensile testing procedure that would yield accurate and reproducible parameters as input material properties into computational models for numerical simulations of the mechanical behaviour of TM380 mild steel. To achieve this objective, we reviewed the ISO 6892:2009 tensile testing standard along with reported good practice guidelines. Tensile tests were conducted on a dog-bone shaped TM380 mild steel specimen with strain gauges attached on either side, to monitor alignment and measure strain, using three different types of tensile testing machines. Parameters quantified included yield stress, ultimate tensile strength, and modulus of elasticity. The values of these parameters were found to be in agreement with the values supplied by the manufacturer's specification and showed minimal variations between laboratories. Thus it can be concluded that the tensile test procedure used resulted in accurate and reproducible results. The strain values calculated as per standard were in disagreement with those determined from extensometer and strain gauges and resulted in lower elastic modulus values. This confirms that the current testing procedures require the use of long-range strain gauges or extensometer to determine the strain. A chemical analysis was conducted to verify the specification by the manufacturer. The specimen was found to be fairly homogeneous with minor sulphide inclusions. The micrographs reveal a pearlite and ferrite structure typical of mild steel, and the fractographs show a dimpled surface typical of ductile fracture, which is an attribute of mild steel.

Jan 1, 2013

In China, thin coal seams are rich in resources but are technically challenging. The mineable reserves in these seams account for 20.4% of the total coal resources, while the current production accounts for only 10.4% of the total annual production. Characteristics such as narrow mining space, low level of mechanization, poor working environment, and high cost of mining, restrict the development of mining safety and efficiency. Recently, fully mechanized mining technology has developed rapidly for thin coal seams, the level of yield and efficiency has reached or exceeded the international standard, and some state-owned key coal mines are considering automation of their mining process. In thin coal seams with hard stone bands that contain concentrations of pyrite, a specialized software, LS-DYNA, is used to calculate the rational blasting parameters that are used in the deep-hole pre-splitting blasting. Using this method the hard stone bands are fractured effectively, and hence increasing the coal productivity. In addition, mining advance rate were increased by enhancing the level of fully mechanized equipment and safety improved by increasing gas drainage from the gas outburst prone seam located some 7 m below the coal horizon. At present, thin coal seam mining technology faces many challenges, including the low level of equipment automation, the low advance rate in mixed coal-rock ground, and the large number of the mine personnel underground. By lowering the labour intensity and improving efficiency through automation and other measures, more efficient working faces can be implemented in thin coal seams.

Jan 1, 2012

By H. Rosen

The pump is the heart of most industrial and mining plants, providing the energy to separate valuable minerals from process feed. The actual effect of the pump, both in terms of production costs and overall process efficiency, is often assumed or misunderstood by engineers due to insufficient pump performance data. Pump performance can be understood and corrected, where required, through continuous performance monitoring, leading to dramatic improvements in both pump life cycle costs and system efficiencies. The performance of every pumping application is subject to variation and the main contributing factors are as follows: ?Unavoidable deviations from pump supplier curves ?Pump wear ?Pump curve derating factors for slurry pumping ?System curve variation ?Deviation from basic principles of centrifugal pump operation. These are discussed in detail through case studies and the author?s personal experiences. This paper shows ways to minimize the effect of these variations, thereby reducing performance loss and preventing damage to the pump. The paper discusses the benefits of efficient pump operation, the requirements of pump performance monitoring, and its practical application to pump operation in the slurry and water environments. The cost of remedial actions is explored and compared against the savings in both power and plant reliability, resulting in a reduced life cycle cost of the pump.

Jan 1, 2010