Search Documents

By Mike Stanley

This is a case study of an opencast coal mining operation where the physical and financial performance was improved via applying a process of transformational leadership development. [ ]

Jan 1, 2008

By B. M. Munyungano

Rössing Uranium Mine operates a recovery circuit with continuous ion exchange followed by solvent extraction. Serious organic degradation problems were encountered during 1985/6, 2000 and 2005 in the solvent extraction plant. The preferential loss of the tertiary amine extractant was observed during the above-mentioned period. Previous investigations revealed that the tertiary amine was breaking down to nitrosamine, which cannot take part in the exchange reaction with U3O8. A reduction in the redox potential of the solvent extraction plant feed to below 500 mV halted this preferential loss. A lot of effort has been made to try and understand the actual mechanism for nitrosamine formation. Current understanding for the degradation is that formation is due to high nitrates on the strip side of the circuit emanating from nitrates from the precipitation process using ammonia. It is the current belief that pH lower than 3.7 on the strip side results in loading of nitrates onto the solvent. If oxidizing conditions prevail on the extraction side of the solvent extraction circuit, the tertiary alamine will then degrade into nitrosamine. This phenomenon is yet to be established and verified. It has, however, been established that the above process is brought about the following conditions ?High redox potential greater than 550 mV predominately caused by a high Fe3+/Fe2+ratio (4:1) ?Perception that if Fe2+<0.5 g/lit will contribute to high redox ?High concentrations of NO-3 in the conc eluate (feed to SX)/ammonium sulphate (NO-3> 4 g/l based on historic values) ?Presence of Mo as a catalyst ?Tests also have proved that the presence of nitrous acid in a concentration of 1 g/lat 550 mV leads to formation of nitrosamines from alamine.

Jan 1, 2007

By V. Matou?ek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

The variety and sources of sampling errors have been studied since the late 1800s, but the pioneering work of Pierre Gy in the 1950s provided insights into sampling as an error generating process. Total sampling variance is a measure of the total sampling error, but disaggregating the variance into its component parts is problematical. Ten sources of error and error generating processes have been identified, some of which can be eliminated through rigorous application of the principle of correct sampling. Others can only be minimized but never eliminated. Three principal questions relating to the appropriate mass of a sample, the fragment size of the sample and the size of the associated error are addressed. These questions relate principally to the Fundamental Error (FE), the only error that can be estimated before the sampling event. Aspects of constitutional and distributional heterogeneity are examined, as are the essential components of Gy?s formula including the shape factor (?), the granulometric factor (g), the mineralogical composition factor (c), and the liberation factor, l. Applications of Gy?s equation to the problems of sampling in the minerals industry are explained using real-life examples. The approach to sampling taken by Pierre Gy provides an excellent inferential relationship between the mass of material to be sampled, the size of the fragments being sampled, and the relative variance of the sampling error. It also provides solutions for three of the main problems associated with the Theory of Sampling.

Jan 1, 2007

By B. P. Watson

In South Africa, the Bushveld platinum group metal deposits are unique in that they are the largest platinum group metal deposits in the world. These deposits occur as two distinct stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the open stopes. Crush pillars are commonly used in this role, where the residual pillar strength provides the required support resistance to stabilize the stoping excavations. This paper describes the direct measurement of stress within these crush pillars, and describes the stress?strain behaviour of these pillars. These findings indicate that the measured pillar failure stress is too high. The implications of these findings are that roof damage and pillar bursting could occur, and some examples of this type of damage are shown. The paper concludes that this problem could be mitigated if the three dimensional pillar geometry were modified and the pillars were cut smaller.

Jan 1, 2007

By A. Hoogervorst

Cyanide is a key contributor to the efficiency of gold extraction. Public perceptions of cyanide are emotive and following some publicised incidents involving cyanide, the gold mining industry established a voluntary cyanide code for the manufacture, transport and use of cyanide in the production of gold. The paper describes the development of the code, its content and the third party auditing of the code as a means of establishing and maintaining benchmark standards. In adhering to the cyanide code requirements, there are overlaps with other management systems such as ISO 14001 and OHASA 18001 and the paper seeks to show how existing mine systems can readily accommodate cyanide code compliance and that operating and auditing the cyanide code can assist in the integration of mine heath, safety and environmental management systems.

Jan 1, 2009

By H. Edinger

China?s engagement with the African continent has increased impressively in the past decade. Even though China is not the African continent?s largest stakeholder, the rapidly increasing engagement is evident in the huge number of Chinese migrants that have come to Africa in the wake of unprecedented trade and investment levels, as well as in increasing diplomatic and political interactions, which has taken most other commercial partners by surprise. All but four countries in Africa have adopted the ?One China?1 policy stance; and in so doing opened the door for new or strengthened commercial dealings with China, including increasing investments into Africa?s extractive industries. This has been particularly evident since the turn of the century, with a clear shift in China?s policy towards Africa elevating the continent in China?s foreign policy objectives. As such, Africa has become a strategic focus2 for Chinese outward bound and internationalizing companies, especially in the extractive industries. This planned shift in focus is based largely on geo-strategic and commercial needs and interests, rather than previous ideological ones.3

Jan 1, 2011

By D. F. Malan

This paper describes the development and implementation of amine-wide continuous stability monitoring system at the Declines Section, Anglo Platinum Union JV. The Declines Section at Union JV experienced a number of large panel collapses during 2005 and 2006. As well as posing a major safety risk, the panel collapses had a major effect on production since the Declines Section is a semi-mechanized operation. The collapses would often extend into the mechanized strike roadways, resulting in a loss of access to both current and future production faces. The collapses have been largely overcome owing to a change in support design and the implementation of a mine-wide stability monitoring programme. This paper describes the precursors to collapses, which were identified using continuous closure measurements and the remedial measures taken. It also outlines the design and introduction of a robust and reliable monitoring tool, which is now used on a mine-wide basis to provide early warning of large-scale collapses.

Jan 1, 2010

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

The relationship between the aspect ratio and physical fields in aluminium reduction cells wase studied numerically. The aspect ratio was firstly defined and 7 kinds of 320 kA cells with different aspect ratios were put forward. By using numerical simulation, the relationship between the aspect ratio and the electric-magnetic flow fields, magnetohydrodynamic stabilities, and thermal stability was discussed. It is concluded that the electric-magnetic flow field distributions are greatly affected by the aspect ratio. From the perspective of magnetohydrodynamics stability, the larger the aspect ratio is, the more stable the cell will be. A larger aspect ratio is more beneficial for the thermal stability under the same current density.

Jan 1, 2011

By S. Kauchali, J. van Dyk, J. Feris, S. Pershad, M. van der Riet, D. Love, J. Brand, C. A. Strydom

"This paper offers an introduction to and strategic context for the other papers included in this special UCG edition of the Journal of the Southern African Institute of Mining and Metallurgy. South Africa is facing long-term energy security challenges, brought about by a myriad of factors that are somewhat unique or exacerbated in the global context. Underground coal gasification (UCG) is a process used to produce synthesis gas from coal in situ, that is, in the coal seam. UCG is an emerging, advanced clean coal technology that offers a potential solution for these challenges, as it can cost-effectively and cleanly liberate vast coal resources in the country that currently cannot be economically exploited using traditional mining technologies. One of the tasks of the South African Underground Coal Gasification Association (SAUCGA) is to advance the development of UCG in South Africa by compiling a technology roadmap. This paper presents the initial findings of the SAUCGA Roadmap (Draft), and contextualizes the technology opportunities and challenges, stakeholders, and provides a basis from which to progress further plans for technology development. Firm development plans and deadlines are not yet possible due to the reliance of the UCG Roadmap on the higher level South African energy policy and regulatory framework. However, the draft roadmap has taken the first step of identifying these policies and stakeholders, and should be seen as the seed from which this embryonic technology and industry can be further developed. IntroductionSouth Africa’s long-term energy security challenges include energy access and affordability, dwindling reserves of accessible bulk primary energy, mounting environmental concerns with all forms of energy generation (especially coal and nuclear), balancing the electricity grid by incorporating an increasing proportion of non-despatchable renewable energy sources, mounting environmental liabilities regarding defunct mining operations, and lastly but by no means less important, fluctuating exchange rates and energy commodity prices.Correctly managed underground coal gasification (UCG) is an emerging, advanced clean coal technology that offers a potential solution for these challenges, as it has been shown to have the potential to cost-effectively and cleanly liberate vast coal resources in the country that currently cannot be economically exploited using traditional mining technologies."

Jan 1, 2019

By K. L. Morton

This technical note reviews the status quo of mud rushes and flooding, which have claimed them lives of many people in underground mines in South Africa and globally. Given that the causes are well known and can be managed, the note calls for the development of a national and global standard on flood and mud rush prevention in order to save lives.

Mar 30, 2026

By E. E. Almási, G. Mucsi, G. Rákhely, Á. Rácz, B. Csőke, Zs. Pap, K. Bohács, N. Halyag

Wet stirred media milling is a widely applied grinding process in the field of mineral processing to produce <10 μm ground materials. In this paper, the results of wet stirred media milling of different Ti, Fe and Cu-oxide and phosphate minerals are presented. During the experimental work, grinding of ilmenite, vivianite, hematite and cuprite was carried out in a continuous operation wet stirred media mill. During the experiments, the particle size distribution and specific surface area of the ground materials were determined after a certain grinding time, as well as measuring the specific grinding energy, thereby determining the grinding kinetics of the different minerals. The measurement results showed the differences and similarities in the grindability of the individual minerals. Nano particulate vivianite, hematite and ilmenite was successfully manufactured in a stirred media mill; however cuprite was characterised as the coarsest final product for the same grinding circumstances. Keywords: Wet stirred media mill, cuprite, vivianite, ilmenite, hematite

Jan 1, 2020

Outotec?s direct leaching process is an atmospheric leaching process for sulphidic zinc concentrates. The direct leaching process, based on special leaching reactors developed by Outokumpu, is the most economical way to produce electrolytic zinc. The production scale applications of the process realized so far are in use at Boliden?s Kokkola and Odda zinc plants. A new full-scale application of Outotec?s direct leaching process will be started in 2008 in China. The process is integrated into the existing production plant, replacing part of the old production facilities by modern technology. Besides high zinc extraction the plant expansion and modernization offers also indium recovery, iron precipitation and solution purification processes. The process equipment includes tailor-made reactors designed on the basis of the work and experience of Outotec research centre. Keywords: zinc, concentrate, atmospheric leaching, technology, indium, iron precipitation, solution purification, Outotec.

Jan 1, 2008

Nowadays, fully encapsulated rockbolts have become a key element in the design of ground control systems. The main reason is that they offer high axial resistance to bed separation. In this research, the load transfer capacity of a fully grouted bolt is evaluated analytically in an elastoplastic rock mass condition. The research considered the effect of bolt end-plate on load transfer capacity. Bolt and surrounding materials were assumed to be elastic and elastoplastic materials respectively. The load transfer mechanism of a fully grouted bolt is a function of parameters such as bolt length, shear stiffness of interfaces, in situ stress, presence of face-plate and distance along the bolt. These factors were analytically evaluated. Finally, the load along the bolt was predicted in different surrounding rock mass characteristics.

Jan 1, 2011

By R. W. O. Kersten

Backfilling is one of the options available to the mining engineer in mine design. The decision as to the type of backfill is dependent on the purpose for which it will be used. For example, in a situation where high-grade, steeply dipping multiple reefs are to be mined, the purpose would be the following: ? to facilitate maximum extraction; a ? to minimize loss of fines; ? to allow closely spaced multiple reefs to be mined; and a ? to create a working platform. The physical properties required which will satisfy the abovementioned requirements can then be defined; the design of the fill plant, as well as the transport of the fill, will be governed by these considerations. The same procedure is also adopted in deciding on backfill in single- reef gold mines. The first question to be asked is the purpose of the fill. It may be to reduce the energy release rate, for environmental reasons, to reduce timber usage, to improve productivity, to reduce stoping costs, to obtain higher mining extraction, and so on. Only after one, or a combination, of these factors has been selected, can the specifications for the fill be decided on, and the plant designed accordingly. The introduction of backfill at Sheba Gold Mine will be used to illustrate the procedure adopted by Anglovaal in determining the type of fill required.

Jan 1, 1988

By R. Gurung, S. Asokan, Ch. V. G. K. Murty, R. Upadhyay

Tata Steel Limited which is Asia?s first and India?s largest integrated private sector steel company, as part of its vision to grow in related industries is also undertaking the Titania project. The project will involve mining, separation of ilmenite and other valuable minerals from the inland heavy mineral sands deposit in the Indian state of Tamil Nadu. The raw material will be beneficiated to synthetic rutile, titanium dioxide pigment and ultimately to titanium metal. The recently concluded feasibility study revealed that the deposit under consideration has 10.4%of total heavy mineral content and 15.2% slimes of the size below 63 µm, over an average sand thickness of 6.9 metres. The presence of about 15% slimes in ROM sand coupled with scarcity of water at the project site complicates the slimes handling/disposal system, requiring the development of an innovative, efficient and effective system for disposal of slimes. Mineral characteristics of slimes revealed the presence of kaolinite clay, which poses its own challenges in thickening/dewatering of slimes. This paper outlines the detailed studies conducted, including slime characterization, settling and thickening characteristics, and ge-technical studies to arrive at an efficient and effective slime handling/disposal system, with a view to plant saplings on the mined-out reclaimed land with species typically suitable to that environment.

Jan 1, 2007

By O. Y. Ntrama

Lebowa Platinum Mines has been in operation since the late 1960s and is a relatively small producer compared to Anglo Platinum?s other operations. The mine has never had substantial capital investment to expand its production scale even though its resource base is estimated in excess of 100 years at current mining rates. It is forecast that the mine will become unprofitable after 2008 due to the workings of the ageing infrastructure, the Merensky Reef operations being further from the shafts, decrease in productivity and increase in operating costs. In order to reverse the forecast decline in operational inefficiencies and profitability the replacement of the Merensky Reef operations at Vertical and UM2 shafts with the development of a 120 Ktpm Brakfontein Merensky Reef Mines is in progress. This paper covers the operational readiness framework developed from the control budget estimate and outlines an integrated business process adopted to ensure that the requirements of the investment proposal are met. The operational readiness framework, which addresses the transition process, will ensure that at operational start-up, all appropriate operating systems, procedures, information and legal requirements are in place, whereas the business integration process will aim to develop and sustain an organization with the appropriate infrastructure and workforce equipped with the necessary skills to meet Brakfontein?s requirement, and where possible embark on an optimized accelerated production initiative to ensure that the objectives of the investment proposal are sustained. Keywords: operational readiness, business integration, optimized accelerated production initiative, organizational development.

Jan 1, 2006

By S. Curry

The Objana Cement Plant is located in central Nigeria, approximately 200km south of capital city Abuja (figure 1). It is the second largest cement plant in Africa, and the fifth largest in the world [1]. The selected mining location is unique as it has all the major raw materials (except gypsum) in close proximity. This includes limestone, clay, marl, laterite soil, and laterite iron. [ ] The plant has a capacity of 5 million metric tones per year (~15,000 tones per day). A 135 megawatt gas-fired power plant, with 90 km of natural gas pipeline, was constructed to power the plant. The total project cost is approximately 1.2 billion US dollars. The lifeline of the plant is two overland conveys totalling 7.7km in length. The first 800m conveyor is relatively mundane. The second conveyor however, is unlike any other troughed belt conveyor in the world. It 6.9km length transports 2,400 T/H and operates at 5.0 m/s. Its ?snake? profile consists of 11 vertical cuvees, and four horizontal curves. The last of which is 2,000m in radius, has a length of 2.2km, and is located at the high tension head end of the conveyor. Although these specifications are noteworthy, the unique feature of this system is that it is entirely elevated from head to tail using a triangulated truss gantry structure (figure 2).

Jan 1, 2008

By B. Kweto, W. Legodi, C. van Buuren, R. F. Sandenbergh

Biooxidation, and especially the BIOX® process, is a viable, economical and environmentally attractive process to liberate gold hosted in refractory sulfides by oxidatively leaching the sulfides as soluble sulfates. The moderate to high cyanide consumption during the subsequent cyanidiation of the washed biooxidation residue is probably caused by the retention on the solids of labile sulfur species formed during the multi-electron oxidation process of sulfide to sulfate. In this work the nature and mode of transport of the cyanicides in the products from the mesophile BIOX® process, as well as that of the combined mesophile and thermophile bioxidation process, were considered and strategies to reduce cyanide consumption evaluated. It was found that labile sulfur species were the major cyanide consumers in the mesophile biooxidation product, forming predominantly thiocyanate during cyanidation. The transfer of labile sulfur species was only marginally decreased by more intensive and thorough washing of the biooxidation products with warm and hot water, intense stirring and warm caustic leaching. A major reduction in cyanide consumption was however achieved by using a combined mesophile and thermophile biooxidation process. Keywords: Biooxidation, refractory sulfide gold ores, cyanide consumption

Jan 1, 2020