Search Documents

By John Taylor

?Introduction to Black Mountain ?Historical metal accounting practice ?Metal accounting audit ?Feed measurement ?Sample precision ?Concentrate measurment ?Current metal accounting practice ?Further refinements to the metal accounting practice

Jan 1, 2005

By V. M. Lovell, N. P. Finkelstein

The concepts involved in flotation research are discussed and aims are presented. Three different methods of investigation can be used, all of which are applied at the National Institute for Metallurgy (N.I.M.), and these are the empirical, trial and error method, the chemical engineering method, and the physicochemical approaches. This paper is devoted to the last of these. Because of the complexity of the physicochemical interactions involved, the work has, to a large extent, been concentrated on only one aspect, viz. the interaction between the mineral surface and reagents in solution, which was considered of major importance in the understanding of the process. The aspects on which work has been done are the concentration of uranium, the reaction between salt minerals and fatty acids, mixed xanthate-cationic collector systems, and the reaction between sulphide minerals and thiol reagents. Selected problems from the first two of these are discussed in some detail and deal with the agglomeration flotation of uranium and the chemical control of the flotation process for phoscorite. A detailed discussion is also presented of the progress made in the understanding of the interaction between sulphide minerals and thiol reagents, which is of more general application. Finally, an indication is given of the future direction of physicochemical research at the N.I.M.

By C. L. E. Swartz, I. J. Barker, J. H. Schubert

A dynamic simulator of the leaching and adsorption cascades of a gold plant was developed and used to compare the effect of various disturbances on the overall efficiency of the plant. These comparisons show which disturbances most critically need to be controlled to optimize plant performance. The simulator was based on an existing gold plant. Dynamic and steady-state data were collected on the plant and were used in the modeling of the process. Simple dual-rate models are used to describe the leaching and adsorption processes. Mole-balances of various species take into account the changes of concentrations in the leach, and also the movement of pulp and carbon up and down the adsorption cascade. Fluctuations in the flow rate, density, and cyanide concentration of the feed to the leach have a negative effect on the efficiency of the leach, while carbon attrition was found to be an important factor in decreasing the efficiency of the carbon-in-pulp (GIP) section. Badly regulated transfers contribute towards the decreased efficiency of the GIP section, but overflows and carbon leakage have only a limited long-term effect. Various carbon profiles and transfer schemes were studied, and the results indicated that a slightly heavier loading at the bottom of the cascade is beneficial, while the type of transfer is relatively unimportant.

Jan 1, 1993

By P. G. Van Der Walt

This paper deals with the reticulation of deslimed tailings from surface to the stope face underground. Reference is made to the experience gained at the pilot plants operating on four of the gold mines administered by Gold Fields of South Africa, as well as at the full-scale system at East Driefontein which was commissioned recently. Mine-wide backfill systems are currently being installed on five other mines administered by Gold Fields. These six full-scale systems are capable of handling more than 270 000 tons of backfill solids per month. The type of reticulation system chosen, the selection of flowrates and the composition of the slurry, as well as the selection of the appropriate pipes and ancillary equipment are discussed. Both theoretical and practical aspects are taken into consideration. Other aspects covered include the design of underground storage dams and communication systems.

Jan 1, 1988

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

By A. C. Scott

A detailed fundamental model of a zinc electrowinning cell has been developed and validated for both steady state and dynamic simulations. This model was used to investigate the effects of a range of operating variables and to find their optimum values. As well as providing useful design information for a planned upgrading of the EZ refinery, more generally it demonstrates the potential benefits to the minerals industry of the applications of modern CAD flowsheeting techniques. The SPEEDUP equation oriented CAD package was found most suitable for this task as the user can easily generate models specific to his site with any number of components and mixture properties.

Jan 1, 1987

By S R Grano

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: ? cell-by-cell and size-by-size metallurgical, ? cell hydrodynamic, and ? pulp and surface chemistry information. The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 µm) copper sulfide mineral recovery but without adversely affecting coarse (+150 µm) copper sulfide mineral recovery.

Jan 1, 2007

By K. R. Noble

The planned extraction of the No. 1 shaft pillar at Blyvooruitzicht Gold Mine highlighted a number of potential problems. In spite of the relative shallowness, careful thought had to be given to stope phasing owing to the detrimental effect of the anticipated geology and the fact that uninterrupted hoisting was necessary. Extensive use was made of computer modellig to design the stope phasing, determine the influence of regional support and to predict the direction and magnitude of displacements in the shaft. The paper describes the success of this design approach, and measured displacements in the stoping horizon and shaft barrel are compared to those obtained from the original computer model

Jan 1, 1987

By H. W. Read

The South African platinum industry finds itself in the midst of a rapidly evolving society that is no longer characterized by the apparent stability of the previous decades. The features of this society include increasing global competition, rapid technological innovation, a declining skills pool, major political transformation, a more challenging working environment as the mines reach deeper into the earth?s crust and a greater concern for human welfare. It is therefore axiomatic that new ways will have to be found to engage the all-pervasive change in the mining environment. Although in general terms project management is a universal endeavour for managing change, it takes place in a specific socio-techno-economic environment and geographical setting that gives it a particular context. The argument of this paper explores, analyses and synthesizes the impact of these changes on the emerging project management methodology. In essence, the management of change will inevitably contribute to the emergence of new dilemmas, issues and challenges. The change management process and procedures will also be affected by this change and in response, drive internal change of its own structures and organization. And, therefore, a new paradigm of project management will become apparent. A new project management model will then be proposed to the industry.

Jan 1, 2006

By P. R. Labrum, H. A. D. Kirsten

The literature on shotcrete is reviewed with the object of identifying aspects that have not been addressed specifically in terms of its structural performance and manufacture as applied to underground mines. The programme and results of a series of full-scale tests on mesh- and fibre-reinforced shotcrete panels are presented, from which it is concluded that fibre-reinforced shotcrete is competent, especialy at large deformations, and is equivalent in structural performance to mesh-reinforced shotcrete for a fibre content of 3 per cent by mass: furthermore, that the support design systems developed for mesh-reinforced shotcrete are directly applicable to fibre-reinforced shotcrete. The Q-NATM system for the design of temporary tunnel support is presented briefly as one such system. It provides for the integrity of the excavation to be considered in terms of its competence and displacement determinateness, and represents the first systematic procedure for the design of temporary tunnel support. Finally, the support designed on the basis of the Q-NATM system for the main and cross-cut tunnels on the production level in the proposed BA5 block cave at Premier Mine is presented as a practical example of the design of fibre-reinforced shotcrete as part of an overall support system.

Jan 1, 1990

The block caving mining method is used to mine large orebodies in weak rock types. The layout for block caving requires that a considerable amount of development is carried out on the extraction drives and drawpoints at the bottom of the caving block. The development further weakens the rock mass, and stability problems arise in the extraction drives and extraction pillars. This paper describes the application of three-dimensional boundary element models in analysing alternative extraction level layouts for a block caving mine. The objectives were to establish whether the use of lateral pillars between drawpoints was warranted, and whether the lateral pillars should be offset or not. The stability of the rock mass within the pillars as well as the stability of the extraction drives were taken into account. The results showed that after undercutting, the horizontal and vertical stresses in the extraction level would be reduced. The lateral pillars would significantly improve the stability of the extraction pillars and extraction drives. There would be a minor improvement in stability if the lateral pillars were offset.

Jan 1, 1987

By P V. Savage, T Glück, RCA Minnitt, C Bothma

Manganese Metal Operations ?Manganese Metal Company (MMC), a subsidiary of Samancor BHP Billiton, has two production facilities for electrolytic manganese metal in South Africa and produces a range of about 44 Mn metal products. ?The company is accredited with ISO 9000 and uses Six SigmaTM for continuous improvement. ?The control of the process relies on the effective functioning of approximately 250 different control loops at 50% automation.. ?Approximately 50000 samples are analysed every month. ?There are pyro, hydro and physical unit operations for the production of electrolytic manganese metal flake and value added products ? [ ]

Jan 1, 2005

By S. Poirier, J. -M. Facteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET’s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialized in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET’s programme in mechanization and automation for narrow-vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies(Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow-vein mining industry. Several important impacts of this project will be monitored. In particular, a database of methods and equipment used in narrow-vein mining is being developed. A key thrust is to identify operators’ needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The paper will present the objectives of the narrow-vein mining project and some of the results, including the web site developed to present the results of the project.

Sep 1, 2001

By I. M. Macleod

An adaptive steady-state on-line optimizing regulator is proposed as an integrated approach to the control of autogenous run-of-mine milling circuits. This optimizing regulator continuously estimates an internal model of the controlled process, and, based on this, determines mill fresh solids feed rate, mill water flow rate and sump water addition flow rate such that a circuit performance objective is optimized. The dual -requirement of controlling both the mill pulp load and the load of particles of grinding media size is thus directly and simultaneously addressed. The concept and theory underlying the operation of the adaptive optimizing regulator are discussed.

Jan 1, 1987

By L. Raaths

This paper outlines the process of improvement utilizing performance monitors and GPS systems on an opencast strip mine. Its primary focus is to maximize coal exposure by draglines and secondly to improve on those processes impacting directly on the dragline operation. The Aquila (DM2/5 system) navigation and monitoring systems were installed on the overburden drills. Their main function is to eliminate manual staking and positioning thereby ensuring a regular pattern being drilled. Holes drilled to planned depth reduce drill metres and it minimizes coal losses and contamination at the coal interfaces. The CAES (Computer Aided Electronic System) will be installed and evaluated on the Caterpillar D11 dozers at Optimum. This system ensures a correct dragline pad elevation through the use of planned elevations and GPS technology to achieve the optimal pad elevations for draglines consistently. The draglines are equipped with a Dragline & Operators Performance Monitor. This monitor allows the operator to control his own performance. It reports on all productivity, method and poor operating techniques. These monitoring systems send critical operational information back to the office. This source data resides in central databases from where it is converted and integrated into management information. To manage an operation means that you as a manager must be able to set objectives and targets and to achieve your goals the activities involved must be measurable.

Sep 1, 2001

In many practical situations, the samples available to estimate a block of ore are not located on a regular grid. The sample sizes and orientations are not constant, and the number and relative position of the samples used for valuation of each block change from block to block. Estimation of a block W might be very complex and time consuming if each sample in the neighbourhood of the block were considered individually. A practical solution consists of grouping the samples in blocks Wi (i = 1, 2, . . . n) in the neighbourhood of W, and estimating µw as a weighted average of the mean xi of the samples in Wi. Possible ways of grouping the samples are illustrated in Fig. 1 1.1. More complex patterns can be found in the literature (Krige, 1966) To calculate the kriging estimator of pw, we must be able to calculate the variance of xi, the covariance of xi and xj, and the covariance of xi and pµw. The purpose of this chapter is to show how these quantities can be calculated when we ignore the position of the samples in the block Wi. We consider the samples to be randomly distributed in Wi; kriging with this assumption is known as random kriging.

Jan 1, 1978

By Stephen Hughes

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in the lead and zinc industries, as an efficient and highly flexible pyrometallurgical reactor with accompanying excellent environmental performance. For the processing of lead and zinc bearing feed materials twenty one (21) Ausmelt furnaces are now in operation, under design or under construction. With recent increases in the value of both lead and zinc and an ever increasing focus on the sustainable use of resources, interest in the processing of secondary feed material sources as well as metal containing residues has substantially increased. Ausmelt Technology has proven to be well suited to the economic recovery of values from such sources. This has for example culminated in Ausmelt?s commitment to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This paper describes Ausmelt?s recent developments in the fields of lead and zinc processing, as well as further investigations into new processing areas, including the direct smelting of zinc concentrates. Ausmelt?s TSL Technology can now be regarded as Best Available Technology (BAT) for metal production.

Jan 1, 2008

By R. Hoare

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development team's processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement. TSG Consulting advocates a `total integrated system approach' to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007

By J H. Sullivan

Contents Background information Locality of Kumba?s Iron Ore Mines Sishen?s Product Specifications Geological Description of boreholes Sample Preperation Block delineations Production Geology Process Laboratory information Turnover times reached Inter Laboratory Comparisons Quality control activities in lab Purpose of laboratory Results attained Standard samples Monitoring of processes with QA/QC standards Mean paired difference of duplicates Duplicate samples Conclusion

Jan 1, 2005

By G. W. Holl, E. G. Fairon

A review of some aspects of shaft design by G. W. HOLL, Pr. Eng., Associate of the Mine Managers Association of South Africa (Fellow)- and E. G. FAIRON, Pr. Eng., F.S.A.I.E.E., M.I. Cert. M.E.E., M.I.Mech. E., (Visitor) The reasons for the choice of vertical shafts in preference to inclined shafts of comparable capacity are set out, and the conclusion that the former are superior in virtually all circumstances is substantiated. The shapes of vertical shafts sunk during the past sixty years are recorded, and the shapes of those sunk during the past decade are analysed. From this analysis it is clear that circular and elliptical (and quasi-elliptical) shafts are the shafts of the future and that the rectangular shape will conceivably become obsolete. The determination of the size of shaft is discussed and it is forecast that shafts of a diameter of 13 metres and over will probably be sunk without difficulty in the years to come. The depth of the shaft is determined intrinsically by the Mines and Works Regulations applicable to factors pf safety of winding ropes and the design of the winding system. The Blair winder is the most suitable winder for hoisting rock, men, and material from a depth of, say, 3000 metres on an economic basis. Tertiary shafts will, therefore, be unnecessary in future deep-level mining projects at the limit of depth now envisaged. A few other factors relating to shaft design are described.