Search Documents

By M. Kumral

Raw material fed into a processing or refining plant is required to be uniform in composition for several reasons. When the mined ore is highly variable in quality the only way to ensure consistency is to homogenize the ore prior to the process. The problem is more complicated in the case of multiple ore sources. The idea behind the research is that theoretical blending ratios can serve not only to meet predefined specific criteria but also to reduce grade fluctuations of variables under consideration. In this paper, the problem is formulated as a quadratic programming problem, whose objective function is in quadratic form and constraints are linear. A case study was conducted on a data set from an iron orebody to demonstrate the technique. The objective was to minimize the blend variability in terms of each variable (in this study, iron, silica, alumina and lime) grade of ores extracted in three different production faces. The stockpile capacity, lower and upper limits of each variable satisfying operational requirements and non-negativity were constrained to the model. A modified simplex method developed by Wolfe was used for solving the blending and homogenization problem. The promising results can be used as apart of the stacking and reclaiming design. Keywords: blending and homogenization problem, quadratic programming, Wolfe method.

Jan 1, 2005

By A. Bhattacherjee

The Shewhart [X]?and R charts are still the most popular control charts in use today for continuous monitoring of quality data. However, for these charts to function properly, the underlying assumption of normality and independence of data must be satisfied. When either independence and/or normality of data are not present, which is a common feature of ore quality data, an application of the conventional Shewhart [X]?and R charts may introduce false alarms in the analysis of the data. To address these issues, a guideline is proposed for construction of appropriate univariate and multivariate control charts for a variety of situations. A use of this guideline to a bauxite mine suggested the construction of special cause control chart for the analysis of individual variables namely, Al2O3% and SiO2%; whereas, the multivariate T2 chart based on residuals is proposed for the bivariate analysis of the variables. The case study clearly revealed that without considering the data correlation, one may be in a state of false impression about an out of control condition while using the Shewhart [X]?and R charts for univariate and the Hotelling T2chart for multivariate analysis. To compare the effectiveness of the control charts, specifically the Shewhart [X]?and the special cause control charts, a simulation study was conducted. It was found that the conventional Shewhart chart provided lower probability of coverage than the special cause control chart. It was also revealed that the quality specification of Al2O3% is met as the variation of Al2O3% is well within the specification limits; whereas, it is difficult to meet the quality specification of SiO2% on a regular basis.

Jan 1, 2002

By A. Feather

Avmin have developed a flowsheet for the refining of copper, nickel and cobalt from Nkomati concentrates. Cobalt is recovered from calcium-saturated solution using Cyanex® 272. Nickel is subsequently extracted using versatic acid. The loaded organic is stripped using spent electrolyte, producing advance electrolyte for recovery of nickel by electrowinning. Cobalt was recovered with >99.5% extraction efficiency, reducing cobalt from 1.8 g/l to <10 mg/l. The cobalt/nickel ratio in the cobalt product solution was >1500. Nickel solvent extraction was optimized to recover 99%, reducing the nickel concentration from 32 g/l to <0.3 g/l, while minimizing calcium deportment to the nickel electrowinning circuit.

Jan 1, 2002

By M. J. Nicol

Mr Vegter has analysed, in some depth, the approximations made in the treatment of the kinetic data presented in the original by ourselves (ref.1) and has come to the conclusion that ?under the experimental conditions used by Adams and Nicol (1986) the steady-state assumption was inaccurate?. We are acutely aware of the fact that the experimental method adopted does not permit the attainment of a true steady-state in the elution reactor. However, this does not eliminate the attainment of a pseudo steady-state by a suitable choice of the experimental parameters with the accompanying simplification of the analysis of the data with the aim of drawing the reader?s attention to the most important objective of the paper viz. the effect of various operating parameters on the rate of elution of gold.

Jan 1, 1997

The paper deals with the results of dynamic tests carried out on a range of surface support liners consisting of combinations of mesh (various types), shotcrete, and wire rope lacing. The testing was carried out over the period 1993 to 1998. The dynamic testing method made use of drop weight impact loading of test samples which attempted to simulate realistic in situ conditions, and the range of loading imposed was equivalent to small to severe rockburst conditions. The results of the testing provide quantitative data, in the form of input energy, which is relevant for support design and for the choice of support types appropriate for situations in which significant mine-induced seismicity occurs or is expected to occur. In addition to the wire mesh and shotcrete liner systems tested, estimates of energy capacity are made for other, untested, systems.

Jan 1, 2001

By F. H. Abd EL-Rahiem

A selective dispersion process is presented and the work carried out to find optimum process conditions to minimise the colouring material in ground calcium carbonate (GCC) is described. The feed material is the overflow product from a hydrocyclone which results from using a Denver Attritioning machine with semi-autogenous grinding for one hour and a 1:1 ore/water ratio. By using sodium silicate (SS), with pH 9 and pulp density 5%, the iron content (as colouring impurities) is decreased from 0.21% in the original concentrate to 0.12% in the final concentrate. The degree of whiteness reached is improved to 85% from 63% in the original material. However, by using hexametaphosphate (SHMP) at pH 10 at the same pulp density, the iron content decreased to about 0.073% and hence the whiteness degree increased to about 96%.

Jan 1, 2004

By J. P. Theron

Paper written on project work carried out in partial fulfilment of Phd.(Process Engineering) degree Process modelling is an essential element in the development of advanced (model-based) process control systems, accounting for up to 80% of the cost of development. Often, models based on historic process data are the only viable option when dealing with processes that cannot be modeled cost-effectively from first principles. Despite major advances that have recently been made in the field of nonlinear process modeling, some basic idea of the dynamic behaviour of a process system is important prior to system identification. While many process systems seem unlikely to be linear, the possible nonlinear aspects of their dynamics are not necessarily supported by the data. This may have significant implications for subsequent system identification or interpretation of the data. For example, it is quite possible that an underlying nonlinear deterministic signal may be obscured by a high degree of measurement or process noise, to the extent that it may be critical in the choice of model to fit to the data. The method of surrogate data analysis has recently been proposed as a means to classify the underlying dynamics of complex systems, and in this paper the use of Fourier transform surrogates to classify process systems is explored. Keywords: modelling, process control, simulation, surrogate data analysis, nonlinear systems.

Jan 1, 2004

By P. J. Bhonde, R. D. Angal, R. H. Tupkary

Manganese imparts numerous beneficial mechanical properties. Hence it finds extensive application in iron, steel and non-ferrous sector. Prevalently, it is incorporated in the form of master alloys i.e. &apos;ferromanganese&apos;. In India, ferromanganese is mainly the inexpensive and paramount source of availability of manganese. Various conventional and non-conventional techniques of ferromanganese production have been adopted in past and present. However, these techniques have demerits viz. high refractory, energy consumption, losses of valuables in slag and fumes. Also geographical co-ordinates of the plant restricted the manufacturer to prefer an appropriate process. Accordingly, the industrially implemented methods had reliance on availability of infrastructure, energy, mineral resources, grade of raw material, outlay of labor, environmental compatibility of technique etc. In view of the liberalized economy and the gap scenario in the supply and demand of ferromanganese, the authors felt it indispensable to explicitly bridge up this vacuum by initially designing a simple energy conserving, eco-friendly, low capital investment technique for decarburization of ferromanganese. Measurement of the data involved studying the impact of rate governing parameters on the process kinetics. This laboratory scale investigation is expected to escalate the Mn/C quotient of high carbon ferromanganese. Key Words: ferromanganese, carbon, carbide, decarburization, rate, kinetic

Jan 1, 2007

By A. J. Van Der Merwe, N. A. Barcza, M. Boyes, N. R. Clarke

Oriel Resources has with the support of SRK (Cardiff) and DRA and Mintek (South Africa) carried our a Definitive Feasibility Study (DFS) to recover high grade chrome ore from its Voskhod deposit very close to Chromtau that is near to Aktobe in Kazakhstan. Voskhod is a large podiform ore body that contains nearly 20million tons of chromite grading about 48% Cr2O3 and with a Cr/Fe ratio of over 3/1. Selected bore hole core samples were obtained from the confirmation drilling programme during the DFS phase of the project in 2005 for pilot plant test work to design the mineral beneficiation plant. The chrome ore is characterised by four main types, namely high grade lumpy and chip sized ore, high-grade fine ore, lower grade (subordinate) lumpy ore and lower grade fine ore. Gravity separation tests carried out by Mintek showed that the large density difference between the high grade (at over 3.7t/m3) and lower grade ore (at less than 2.97t/m3 ) should ensure very good separation in the DMS drum and DMS cyclone stages resulting in high recoveries of Cr2O3 - rich chromite ore products. Very high chrome ore grades of up to 64% Cr2O3 and Cr/Fe ratios of 4 to 1 were obtained at an 80% mass yield from selected samples of lumpy and chip ore size fractions. The overall predicted recovery from the design work on the mine and plant is expected to be closer to about 70% of the ROM (Run of Mine) feed. DRA has completed the design of the mineral processing plant to recover about 900 kt/a of chrome ore from the 1.3 Mt/a of ROM feed. The plant has been sized to handle up to 1.5 Mt/a and will also be able to address the variability in ore feed as different regions in the deposit are mined. The lumpy high-grade product and the chips size fraction is expected to grade around 48% Cr2O3 and the fine concentrate between 56 and 58%Cr2O3 The ratio of products is expected to be about 70, 15 and 15 percent respectively but will vary to some extent during the expected 20 year life of the mining operation based on including the associated adjacent Karaagash deposit together with the Voskhod deposit. The prediction of the product split from the processing plant depends on many factors such as the geology, mineralogy, mining, handling and metallurgical processing. An overall process flow model has been developed that covers the ROM ore, the various types of chrome ore feed to the mineral beneficiation plant, the projected products and the subsequent smelting of the chromite ores to produce High Carbon Ferrochromium. The model allows the optimisation of the quality of the chrome ore in terms of Cr2O3 content, Cr/Fe ratio and recovery to be studied. This information can also be evaluated in terms of the economic requirements for smelting High Carbon Ferrochromium (HCFeCr) at a given location. Oriel is planning to supply chrome ore to Ferrochrome plants mostly in China and Russia. The use of the model will assist to maximise the value of the Voskhod project to its owners and also assist the users of the chrome ore in selecting the appropriate supply quality to meet their needs for a given smelter operation. The smelting of high grade Voskhod ore requires a limited addition of about 5 to 7% quartz to flux the MgO and Al2O3 and about 25% coke as a reducing agent to produce an alloy containing from about 65 to 74%chromium depending on the Cr/Fe ratio.

Jan 1, 2007

By X. Yu

Although many investigations of the deformation behaviour of rocks have been carried out, most of them are carried out in compression. In all rock engineering practice it is usually assumed that the deformation of rocks in tension is the same as that in compression. However, data from numerous researchers have shown that this assumption is not correct for some rocks. A new loading frame for testing rocks in compression and direct tension has recently been developed by the authors, with the capacity to conduct both compression and tensile tests on the same rock sample. The results obtained show that the ratios between the average Young?s modulus in compression (ECA) and in direct tension (ETA) are 1, 1.16, 2 and 6 respectively in four rock types tested. For Poisson?s ratios, analogous relations were obtained. It was observed that, in all cases, the tangent Young?s modulus intension reduces with an increase in the applied tensile stress, while the behaviour of Poisson?s ratio is similar, but shows greater variability. The difference between the Young?s modulus of rocks in tension and that in compression could lead, large errors in calculating induced stresses around underground openings, as well as in determining the Brazilian tensile strength of rocks. This may have a significant influence in rock engineering and therefore more investigation is necessary into the tensile deformation behaviour of rocks and its influence.

Jan 1, 2005

By M. D. Mwema

Copper oxide ores deposits in the Katanga province of the Democratic Republic of Congo (DRC) contain at variable level cobalt oxide minerals. In contrast to copper oxide minerals which readily dissolve in the sulphuric acid solution, the cobalt oxide bearings are difficult to dissolve, especially if cobalt is present in the third oxidation state (Co2O3). This species become soluble after reduction of Co+3in Co+2. In practice, the use of reducing agent is therefore necessary in order to transform the insoluble minerals into soluble cobalt sulphate species. The following reducing agents are currently used at the Shituru plant: ferrous ions, which are present in leach solutions, pulverised copper or sodium meta bisulphite (MBS). Due to the high consumption of reducing agents (0,8 t MBS/t of solubilized Co; 1,2 t Cu/t-Co), cobalt production is expensive. The use of sulphur dioxide as reducing agent was then investigated in order to reduce operating cost. This reagent also presents the advantage of sulphuric acid production during the leaching process. It has been added in the leaching vessel (tank). From the laboratory and industrial tests, selective leaching of cobalt (78%) has been performed. The cobalt leaching kinetic depend on sulphur dioxide dosage. Dissolution of copper, iron and manganese remained very low. No emanation of SO2 gas was observed during the process.

Jan 1, 2002

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By R. T. Jones

The 20 Mt reverberatory furnace slag dump at Nkana in Zambia contains a substantial quantity of cobalt. A 40 MW DC arc furnace has been built at Chambishi for the purpose of recovering cobalt from the slag. The technology was jointly developed by Mintek and Anglovaal Mining Ltd (Avmin), and the furnace was designed by Bateman Titaco. Testwork at the 150?250 kW scale was conducted at AVRL, and larger scale piloting was conducted at Mintek (in partnership with Avmin) in a 3 MW DC arc furnace. Approximately 840 tons of Nkana dump slag (ranging from 0.66% Co) was processed at power levels around 1-2 MW. Good overall cobalt extraction was achieved, and approximately 100 tons of cobalt-bearing alloy was produced (containing 5 to 14% Co). This testwork demonstrated that the Nkana dump slag could be processed in a DC arc furnace of suitable design, to produce a cobalt-bearing alloy suitable for further hydrometallurgical processing. Bateman Titaco were contracted to design and build the furnace, and the design team contained representatives from Avmin and Mintek. The project was conceived as a fast-track exercise, and many activities had to be run in parallel. Notable features of the furnace include an ABB power supply, a Concast conductive hearth, the refractory design, and copper cooling in the sidewalls. Power to the furnace was switched on during January 2001.

Jan 1, 2002

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

By R. M. Whyte

The Konkola Deep Mining Project (KDMP) seeks to exploit the deep level potential of the Konkola Deeps orebody, producing high grade copper concentrates for treatment at the Nkana Smelter and Refinery. As an alternative to smelting, Konkola Copper Mines (KCM) has examined a processing route involving pressure leaching of the Konkola concentrates at Nchanga, with the leach liquor being treated by solvent extraction and electrowinning to produce high purity copper cathode. The solvent extraction circuit would be operated to achieve a high ?delta? copper, thereby providing a strong acid raffinate which can be used in the existing Tailings Leach Plant (TLP) to treat Nchanga oxide copper materials. The main focus of the hydrometallurgical option is to capitalize upon the synergy that exists between the treatment of sulphide copper concentrates (acid producing) and oxide copper ores (acid consuming). The paper discusses the key features of a comprehensive piloting campaign carried out at Anglo American Research Laboratories, which involved the co-treatment of Konkola copper concentrates and Chingola refractory ore in a fully integrated pilot plant circuit.

Jan 1, 2001

By Marco Barla, Mariacristina Bonini, Giovanni Barla

ABSTRACT: The paper describes the characterisation studies of Tectonised Clay Shales at laboratory and in situ scale. The interest relates to tunnelling under squeezing and swelling conditions, in Italy, along the Apennines. The results of monitoring during full face excavation are presented in conjunction with numerical modelling. RESUME: Cet article présente la caractérisation, à l&apos;échelle du laboratoire et in situ, des Argiles Chaotiques. L&apos;attention est portée sur le creusement, dans ces milieux gonflants, des tunnels, dans les zones montagneuses des Appennini, en Italie. Enfin, on présentera les résultats de la modélisation numérique et la comparaison de ces derniers avec les mesures effectuées in situ. KURZFASSUNG: Die Arbeit beschreibt die Charakterisierungsstudien von tektonisierten Schiefertonen, sowohl im Labor als auch vor Ort. Das Interesse gilt dem Tunnelbau unter Quetsch- und Schwellbedingungen in Italien entlang der Apenninen. Die Überwachungsergebnisse des ganzflächigen Ausbruchs werden mit numerischen Modellen präsentiert.

Jan 1, 2003

This paper addresses the methodology of introducing risk into the development of mine plans for open pit mines. Recommendations are put forward for achieving a risk balance between mineral resource estimates and slope design. A design process identifying criteria for different stages of planning is presented. Business risk is separated from geological/geotechnical risk and procedures to address these within the development of mine plans are suggested. It is concluded that a formal design process improves communication between key decision makers and adds value to shareholders, investment.

Jan 1, 1997

By J. H. Schubert

Mintek has developed a level-control system, FloatStar, for use in flotation circuits. Instead of controlling levels separately in each unit, the controller monitors levels throughout the circuit. It can thus take account of the global effects of any control actions. A collaborative project between Mintek and Karee Platinum Mine has begun, looking at aspects of flotation control. Karee plant was chosen as the site for this work because of its good existing control infrastructure. As a first stage of the joint project FloatStar was installed. Analysis during installation and running of the FloatStar has illustrated how circuit design and measurement technology can affect process control. Severe interactions have been observed in the levels of adjacent banks. The effect of FloatStar on flotation performance was tested and an improvement in level control was observed. Similarly, a faster settling of the plant after start-ups was observed. Both the improved level control and faster start-ups lead to higher platinum recovery.

Jan 1, 1999

By J. Rivoirard

Historically, linear and lognormal krigings were first created to estimate the in situ mineral resources of blocks. Nonlinear geostatistics and indicator kriging were subsequently developed to evaluate also the portion recovered when applying a cut-off on selective mining units (SMUs) within blocks. In practice these methods are generally based either on the Gaussian model with a transformation generalizing the lognormal case or on the indicators above cut-offs. Very often the indicator approach is simplified by kriging separately each indicator, and when starting from a continuous variable, a practical advantage of the discretization into classes lies in the easy treatment of a zero effect and of the high values. However, a number of so-called isofactorial models have also been developed for a discrete or continuous variable, where the full cokriging of indicators (i.e. disjunctive kriging) simplifies to the separate kriging of factors. Moreover, these models are equipped with a change of support, allowing a consistent estimation of recoverable resources on SMUs. Min-Max Autocorrelation Factors (MAF) analysis of the indicators offers a new approach for indicator modelling. In particular the first factor, the one with the highest spatial continuity, can help in choosing the type of model. For example a monotonic experimental first factor can be used directly as the basis of a discrete diffusion model, unless a continuous diffusion model such as the Gaussian model can be used on the original variable. This approach is illustrated on a uranium deposit mined selectively: estimates of recoverable resources by discrete disjunctive kriging and uniform conditioning in a Gaussian model are compared locally to short-term estimates based on two areas densely drilled.

Jan 1, 2014

By L C. Pretorius

Pipe pigging is a technique for the in situ (field) coating application, to create a seamless internal anti-corrosive lining of long pipelines. The technology originated in the cleaning of pipes, and these proven cleaning methods continue to be used today. Firstly mechanical cleaning of the pipeline is performed, using wire brush, razor back, course stud and fine wire pigs, then foam pigs, or criss cross pigs, and urethane blade scrapers to remove loose debris, wax, residual hydrocarbons and corrosion products from the pipeline. Part of the proprietary techniques and expertise is to ensure that these cleaning pigs do not get stuck Next chemical cleaning of the pipeline is performed, using repeated pig runs with detergents, solvents, acid etching, corrosion inhibitors, consecutively batched between two pigs, to ensure a clean, dry metal finish to a visual cleanliness standard of ISO SA2½. These in situ techniques were developed, 40 years ago to apply internal corrosion protection to pipes using a thin layer of epoxy based paint (50 to 100 micron). Until recently these old techniques were never improved upon. Although many thousands of kilometres of pipes were successfully coated with these thin film epoxy based paints and old application techniques, these thin paint films had problems in weld coverage, and were also unable to fill pits caused by pitting corrosion, and unable to replace metal loss caused by channel erosion. New coating material developments, revised application methods and modified pigging equipment have now made it possible to apply thick film coatings as corrosion barriers to the internals of pipes in the field, using these pigging techniques. The thick coating films can be up to 1 mm (40 mils) thick in a single coating run over long distances. The new thick film coating materials and application techniques are similar to continuous screeding, creating a far more robust seamless internal pipe lining when compared to the old technology of thin film paints. With thick film polymers the option now exists to create a structural GRP pipe within a pipe, be it steel or cementicious. It has been preferable, even necessary, to move away from the traditional epoxy paints and coatings. It was found difficult or impossible to use epoxy materials for these pipe coating applications due to the requirement for achieving a suitable viscosity with adequate hold up. In order to reduce epoxy viscosity a solvent or reactive diluent is required. This inevitably lead to solvent entrapment and poor cure characteristics in cold climates. Further mud cracking in over thick areas, the inability to extend or reduce pot life, poor control of cure time and limited resistance to aggressive or chemical environments made solvent based epoxy resins a poor choice.

Jan 1, 2006