Search Documents

By Robert Underwood, Boleslaw Tolwinski

In 1965 Helmut Lerchs and lngo Grossmann presented to the mining community an algorithm to find the optimum design for an open pit mine. In their words, "the objective is to design the contour of a pit so as to maximize the difference between total mine value of the ore extracted and the total extraction cost of of ore and waste." They modeled the problem in graph theoretic terms and showed that an optimal solution of the ultimate pit problem is equivalent to finding the maximum closure of their graph based model. In this paper. we explain how a dual simplex algorithm can be used to solve the same problem. We show how this algorithm is closely related to Lerchs and Grossmann's and how the steps in their algorithm can be viewed in mathematical programming terms. This analysis adds insight to the algorithm of Lerchs and Grossmann and shows how it can be simplified.

Jan 1, 1996

By G. S. Dobby, N. J. Contini, S. W. Wilson

Scale-up and simulation of flotation columns requires construction of mathematical models which employ, as a minimum, rate constants for quantifying particle recovery in the collection zone as well as split factors for quantifying froth zone performance. To date, measurement of these rate parameters has proven to be difficult, due to the interdependent nature of the collection and froth zones. This paper describes a technique for making these measurements. The method requires recovery data from two modes of operation: countercurrent and cocurrent. In cocurrent flow slurry is fed at the bottom of the column and tailings are withdrawn a short distance below the froth interface. Countercurrent mode is conventional operation. The critical difference is that particles which are dropped out of the froth in cocurrent mode are immediately lost to tailings, while in countercurrent mode the particles are subjected to recollection. Fitting of the measured recoveries to the equations that describe flotation in the two modes yields rate constant or recovery values for both the collection and the froth zones.

Jan 1, 1988

By J. Alvarez, S. H. Castro

The feasibility of chalcopyrite-pyrite separation in the flotation of a chalcopyritic copper ore, at reduced surface tensions regulated by methanol, was investigated. It was found that with methanol dosages from 0.5% to 1.5% v/ v, the chalcopyrite might be effectively separated from the pyrite, without use of other flotation reagents and pH regulators. However, under this simple condition, the chalcopyrite recovery was only around 50%, recommending the use of other reagents to reinforce the collector action. Low dosages of different collectors were tested, including SF-323 (Shell Float), S-6588 and S-7251 (Cytec), and S-701 (Molycop). Very promising results were obtained with low dosages of the collector S-701 and 1% v/v of methanol in the pulp, which evaluated against a reference test, gave similar copper recovery, higher Mo recovery and higher depression of pyrite. Consequently, this is an alternative process which does not require the use of lime to depress pyrite.

Jan 1, 1995

Energy Developments Ltd. (EDL) has developed power plants at two Australian coal mines that featuring 94 gas-fueled Caterpillar G3516 engine/generator sets. They will convert to electricity 145 kt/a (160,000 stpy) of coal-seam methane gas for sale to a local utility. The $100-million project will cut the sites' methane emissions in half, provide a low-cost energy source and offset mine operating costs. The project began in May 1995. It is located at the Appin and Tower longwall underground mines, 80 km (50 miles) south of Sydney in New South Wales. The installation is one of the first to capture coal-seam gas from mine ventilation air and gas drainage systems. Coal- seam gas contains 40% to 60% methane, which fluctuates constantly. The system is expected to convert 578,000 m3/d (20.4 million cu ft/d) of coal-seam gas to 94 MW. It will also reduce greenhouse gas emissions by 3.5 Mt/a (3.8 million stpy) of CO, equivalent emissions. The Appin and Tower mines each produce 2 Mtla (2.2 million stpy) of clean coking coal. They operate around the clock with about 400 workers per site. The mines are owned by BHP Steel, Collieries Division, which will share the revenues from energy sales. The Appin Power Partnership consists of EDL and Lend Lease Development Corp.

Jan 1, 1997

By Bern Klein, Richard W. Lawrence, Scott Frostad

A laboratory study was conducted to evaluate the effects of various kinetic test protocols on sulfate production, NP depletion and time to acidity. Six test protocols were evaluated including standard humidity cells, non-aerated cells, tall cells, shaken cells, simulated precipitation cells, and NP depletion columns. The study indicates that test protocols which disrupt the oxidizing environment, such as extreme wetting and drying cycles, shaking the cells, or the high addition of acidic water will create an unnatural environment that affect the results. Trickle leach and non-aerated test protocols create an oxidizing environment that more closely represents field conditions and are therefore recommended.

Jan 1, 2000

By M. Prasad, A. K. Majumder, T. C. Rao

The depletion of high-grade phosphate ores is bringing about a search for a suitable, economically viable technique that con process the abundant low-grade phosphate reserves. About 75% to 80% of the world's low-grade phosphate reserves are associated with carbonate gangue that is not amenable to treatment by the simple techniques of physical separation. The processing of sedimentary dolomitic/calcareousphosphate ore has numerous problems, including similar surface properties of the carbonate and phosphate. Two-stage reverse anionic flotation of carbonates (dolomite/calcite) has appeared to be a promising separation technique ,for the removal of carbonates from sedimentary rock phosphate. In reverse fatty-acid anionic flotation, the depression of phosphate mineral with orthophosphoric acid produces satisfactory results for calcareous as well as dolomitic phosphate ores from several locations of sedimentary origin.

Jan 1, 2000

By Dilip K. Sinha

In the paper some interesting cases of applications of Operations Research and Computer Methods as worked out by the author and accepted by the management of some of the newly formed Indian mining organisation for implementation are highlighted. The main emphasis on the application cases was to use simple techniques and methods which yield the result in shorter time period, The case problems mainly deals with the production system optimisation in unit mines, areas/divisions and at the corporate levels. Also the management decisions regarding reorganisation of transport and distribution system of material and mineral are attempted to be optimised. Further, the case of management system development with computer aided decision making worked out for single large Iron Ore Project captive to a steel plant is outlined. Finally, the case of a large mining company having decentralised units and divisions geographically dispersed throughout the country, computerised management decision-information system designed on the basis of inputs and outputs of decision models relevant for different levels of management in the organisation is depicted.

Jan 1, 1986

By K. Tempel

In December of 1999, Newmont Mining Corporation’s Eastern Nevada Operations commissioned its commercial biooxidation facility. The commercial biooxidation facility is a refractory gold whole ore heap process that uses bacteria to assist with the oxidation of sulfide minerals thus liberating occluded gold for further processing by cyanide for gold extraction. Before the commercial biooxidation facility was started, a decade of research went in to developing this state-of-the-art process. During final design and construction of the commercial facility a decline in gold price necessitated cost saving and project scope changes. As a result, the biooxidation process experienced many challenges. Some of the more significant challenges include poor heap permeability due to haul truck stacking, unhealthy bacteria population due to a lack of solution aeration, and insufficient biooxidation time because of limited pad space and high carbonate content in the ore. This paper discusses the many challenges encountered and addressed during the first 2-3 years of commercial biooxidation operation.

Jan 1, 2003

By K. N. Han, M. C. Fuerstenau, T. B. Onlin

A mathematical model describing the concentration profile of fine particles in the axial direction in liquid fluidized beds has been developed for the removal of fine particles. A forward finite differentiation technique has been used to solve a continuity equation with a source term to predict the concentration profile and, hence the recovery as a function of time. With the aid of experimental results obtained using a fluidized bed of 3-cm diam, dimensionless parameters were identified. These parameters were used to predict the concentration profile of fine particles in fluidized beds of larger sizes. Four different sizes of fluidized beds, namely, 1.3, 3.0, 4.0, and 7.5 cm in diam, were used in this investigation. The amounts of bed particles used included 4, 8, 16, 24, 59, and 120 g, and the size of bed particles were 48x100, 100x150 and 150x200 mesh.

Jan 1, 1987

By N. D. Cristescu

An analysis of the interaction between a creeping rock and a yieldable lining is presented. The following cases are considered: an elastic lining, a lining made of circular shaft rings that may slide at their joints, a lining made of circular reinforced concrete panels with wooden compressible strips inserted between the longitudinal joints and a yieldable support that has a compressible broken-rock stratum between the support and plane rock. By formulating a mathematical model for the rock-lining interaction, one can optimize the sequence of excavation-lining application. To keep costs to a minimum, one can also choose the most appropriate lining for the corresponding rheological properties of the rock.

Jan 1, 1997

By A. D. Davis, C. J. Webb, F. W. Beaver

The proposed National Underground Science Laboratory will be housed in the former Homestake Gold Mine at Lead, South Dakota. Uses will include underground neutrino experiments that must be shielded by several thousand feet of rock, as well as ground-water research in fracture-flow environments, and investigation of the microbiology of extreme environments. The Homestake Mine has about 300 miles of underground workings. Seepage of ground water into the mine openings is approximately 500 gallons per minute. Average annual precipitation in the northern Black Hills is approximately 28 inches per year. The majority of this becomes surface-water runoff or evapotranspiration, with little ground-water recharge because of the low permeability of the Precambrian rocks in the area. Dewatering of the workings over the 125 years of operation of the mine has influenced the subsurface hydrology of the 8,000-footdeep mine.

Jan 1, 2003

By Alberto Sarmentero

Venezuela, once a world's top gold producer until 1886 Witwatersrand discovery, did let fall its role then because of a serious lack of infrastructure and population, and lately (since World war II times), because of discouraging mining and taxation laws, laying upon an oil prizes bonanza. Recent research leading to estimates of about 5.000 mt. of gold, mainly related to the greenstone belts of the Guiana Precambrian shield outcropping in Venezuela, are opening the scope for both Government and international investing and mining companies, for gold exploration and development projects in the country. This paper overviews Venezuelan Gold mining industry, as seen from the point of view of a participating mining company.

Jan 1, 1989

By Charles T. Staniek

Following a dragline relocation at Agrico's Fort Green phosphate mine in 1986, the recovery plant experienced a significant decrease in flotation performance. Through weeks of trial and error testing, we discovered we could restore recoveries by conditioning feed at pH's higher than we had used historically. The higher pH's essentially increased flotation cell kinetics, although we still do not understand the exact mechanism at work. Armed with new-found appreciation of pH modification, we initiated a program to determine the optimum modifier for us, from both a performance and environmental perspective. Environmental considerations were important because ammonia, the standard industry modifier, is a plant nutrient and higher usage rates could affect the quality, of our recycle process water. This paper describes the research and development work spanning a 3 year period that culminated in making a major change in our reagent suite when we replaced ammonia with soda ash on a permanent full-time basis.

Jan 1, 1993

By John Marsden

JIM ARNOLD: Our next speaker is John Marsden. John runs the concentrator complex at La Candelaria Project in Chile. John's a Royal School of Mines graduate and he wrote the book on gold metallurgy, The Chemistry of Gold Extraction, which, by the way, he dedicated to me-at least that's what my copy says. [laughter] John, go ahead. (Message shown on Projection screen) ‘Raulerson’s Rules Plant operators and maintenance personnel should be asked to participate early in the design process. This ensures that the plant will never be completed on time or within budget.’ JOHN MARSDEN: Good afternoon, everybody. My presentation this afternoon is going to be very short. It won't be as funny as Joe Keane's, but I guarantee you it will be a lot quicker. [laughter] That transparency isn't mine, actually. [laughter] You're trying to throw me off.

Jan 1, 1998

By R. Hogg, R. H. Weiland, P. Bunnaul

The dewatering of flocculated clay suspensions by compression in a centrifugal field was investigated. The results were analyzed with respect to the direct applicability of centrifugal dewatering (as in solid-bowl centrifuges) and indirect applications to gravity sedimentation systems. An important objective of the study was to evaluate the self-weight effect using centrifugal forces to simulate consolidation of deep sediments. Experiments were conducted in which the sediment mass and initial structure were maintained constant while the effective sediment weight was varied by centrifuging at different speeds. The relationship between the limiting sediment density and the applied consolidation stress was found to be the same for both gravity and centrifugal consolidation, indicating that small-scale laboratory tests can be used to predict consolidation in deep beds. The effects of the initial structure were also studied using controlled variations in flocculation conditions. The results imply that, for the flocculated suspensions studied, the longterm consolidation behavior is relatively insensitive to the actual extent of flocculation.

Jan 1, 1995

By Yoginder P. Chugh, K. V. K. Prasad, R. Missavage

This paper presents results of field monitoring and finite element studies to analyze and improve a room-and-pillar retreat mining system. Fie1 d instrumentation was utilized to monitor pi11ar load changes, roof to floor convergence and differential roof strata movement as retreat mining progressed and to determine in-situ horizontal stresses. A two-dimensional finite element model depicting strata behavior at this mine was developed and used to analyze existing and alternate improved mining geometries. The results showed excellent correlation between fie1 d observed and model predicted behavior. Some of the recommended changes in mining geometry based on the study were incorporated in the mining system.

Jan 1, 1986

By M. L. Gupta, S. P. Banerjee, D. C. Panigrahi

The paper describes the computer simulation of climatic conditions in the longwall workings in India. For this simulation work the longwall panels have been divided into two segments, viz; the intake gate segment and face segment. Two computer models, one based upon transient heat and moisture transfer algorithm of McPherson (1986) and the other on quasi-steady algorithm of Starfield and Bleloch (1983), have been developed for intake gate segments. Similarly two computer models, one based upon the transient heat flow in cylindrical tunnel with certain modifications of McPherson algorithm (1986) and the other on linear heat flow concept, have been developed for face segment. The models incorporate the necessary running and spot heat sources present in their respective segments. In addition to this the goaf heat flow parameters have been incorporated in the models for the face segments. Continuous recording of important thermal parameters have been carried out in several longwall faces in India to validate these models and the results have been presented.

Jan 1, 1993

By Robert L. Bates

An industrial mineral, says the Glossary of Geology, is "any rock, mineral, or other naturally occurring substance of economic value, exclusive of metallic ores, mineral fuels, and gemstones; one of the nonmetallics." Probably most geologists and engineers would accept this simple and straightforward definition, at least as a general statement. On analysis, however, certain anomalies crop up. For example, what is metallic and what is nonmetallic? Bauxite and ilmenite certainly qualify as metallic ores, but both are also raw materials of important nonmetallic substances; hence they are included in this book. Another anomaly is that, by common consent, the term industrial minerals may include not only rocks and minerals but also certain manufactured products, such as cement and lime, and even mixed groups of natural and artificial products, such as abrasives and refractories. Thus the central realm of the industrial minerals is clear enough, but its boundaries tend to be indefinable. Since a definition that allowed for every irregularity in the outer fringes would be excessively unwieldy, the one quoted above may be considered satisfactory. The expression industrial minerals is commonly equated with nonmetallics, and with the somewhat more precise phrase industrial minerals and rocks as in the title of this book.

Jan 1, 1994

By G. T. Adel

This paper presents the highlights of a general-purpose simulator for mineral processing plants that is being developed at the University of California, Berkeley. The state-of-the-art structured design methodogy based on a top-down design approach is being used to construct a modular and completely structured simulator such that it is independent of the unit operation models and routines. The simulator provides for two levels of operation allowing prebuilt or user-built simulation flowsheets depending upon the degree of computer knowledge expected of the user. The philosophy used in designing this simulator appears to be unique in the field of flowsheet simulation. The paper also includes a mini-example demonstrating the usage of the simulator.

Jan 1, 1982

By S. C. Suboleski, J. W. Oberholzer

This paper describes research being undertaken by the Chamber of Mines Research Organization (COMRO) to assist the continuous miner operator and section foreman in the performance of their jobs. The project will initially provide visual assistance to the miner operator, and later it will semiautomate the mining (cutting) process. Using a technique known as "RF tagging," the project will also provide the section foreman with real-time or near-real-time information about the performance of the loading and hauling units. This data will allow the section foreman to quickly detect problems and take action where appropriate. The project is based upon the application of currently available technology, and in-mine testing results from the first phase are now available.

Jan 1, 1994