Search Documents

By J. Yuan

Ground calcium carbonate (GCC) and chemically precipitated calcium carbonate (PCC) have become important mineral-based commodities in recent years. GCC manufacturing generally requires high purity and high brightness deposits of marble, chalk or limestone as the stone source. PCC usually uses limes made from lesser quality limestone deposits. GCC products have a wide span of particle size, with a d50 size ranging from sub micrometers to as large as several inches such as those used in landscaping. PCC products are typically limited to less than 10 µm (1,250 mesh). Each PCC product has a narrowly distributed size range. GCC and PCC products tend to have higher levels of whiteness com-pared with other traditional filler and extenders, such as kaolin and talc. Published statistics of GCC production volume often vary due to the exclusion of certain size range GCC products. According to Roskill’s latest estimate, world GCC capacity was believed to exceed 56 Mt (62 millionst) during 2004 for all grades.

Jan 1, 2005

By R. K. Singhal, H. Sahay

Introduction In terms of the world's recoverable coal reserves, Canada ranks 10th, providing 0.6% of the world's total. The US is first with 27.8% and the Soviet Union follows with 24.1%. Figure 1 shows the principal coal mines in Canada. Several provinces contain substantial coal deposits, but the largest deposits are found in the western provinces of Alberta, British Columbia, and Saskatchewan. Conservatively, 90% of the lignitic, 80% of high volatile bituminous, and nearly 100% of subbituminous, and low and medium volatile bituminous coals are located in these three provinces. During the past decade, Canadian coal production of all types increased from 18.8 Mt (2 million st) in 1972, to 25 Mt (28 million st) in 1975, to 61 Mt (66 million st) in 1984. About 38 Mt (43 million st) of this output was classified at thermal and 23 Mt (25 million st) as coking and metallurgical coal (Table 1). The three western provinces currently produce 57 Mt (62 million st) of coal - 95% of Canada's total. The remaining 3.6 Mt (4 million st) (5%) is produced in Nova Scotia and New Brunswick on the east coast. The majority of western coal (98%) is produced by surface mining methods. On the east coast, though, mining is predominantly underground and only 15% is produced on the surface. In 1985, Canada exported close to 28 Mt (30 million st) of metallurgical coal and thermal coal. During the same period, 15 Mt (16 million st) of coal were imported, mostly from western US for use in Ontario and Quebec. Almost 60% of the imported coal was used for thermal applications. The remaining 40% was metallurgical coal for the steel industry. It is generally cheaper to import coal into central and eastern Canada from the eastern US to augment local supplies rather than from western Canada. This is mainly because of high transportation costs. Mining methods The suitability of mining methods in a particular area depends largely on the geological setting. Geology, therefore, simplifies or adds complexities to mining operations, directly affecting the economics. It also influences the flexibility required from the min-

Jan 9, 1986

By J. Finch, R. McIvor

This paper presents the development of a new grinding circuit steady-state modeling system. It is fundamentally based on the “functional performance equation”, which has now been used to improve the performance of numerous grinding circuits. This equation characterizes the two distinct efficiencies that are at work in a ball milling circuit, and how these relate to overall circuit productivity. It does so based on the particle size chosen to distinguish between coarse and fine (product size) material. Now, by applying it to all the material size classes, a simple yet reliable ball mill model was created. Combined with cyclone recoveries, the complete, detailed grinding circuit performance can be exactly reproduced mathematically by the computer program. It can then be used with separate process equipment application engineering methods to systematically engineer grinding circuit improvements. The development, features, uses and limitations of the system are described.

Jan 1, 2007

By N. Akbulut, A. Anani

From the initial planning phases to the closing of a mine, mining is an industry where high attention, care, and sensitivity are needed in every step of the mine life. Since mining projects have a long-life span, exceeding a decade sometimes, managing a whole mine project is challenging, especially when challenges faced due to generational differences are considered, such as tracking and logging data, or the usage of different engineering solutions change over time. Along with the overall hardship caused by the time put into a mining project, the present-time operations are very costly where each minute counts. In present-time operations, every decision made, and every minute used during planning and operations has an impact on the efficiency, safety, and economics of the project. Having extremely harsh conditions in both the excavation and mineral processing operations not only slows down the processes but creates very dangerous environments that need to be handled with precise safety measurements. To support the already established processes, we could implement new technologies and use them to our advantage. Virtual reality (VR) is one of these technologies that we could implement in the mining industry. VR is a technology that emerged in the 1960s creating virtual environments and platforms. The user experiences these virtual environments from head- mounted headsets to rooms with 360 screens, all with different levels of immersion. These higher levels of immersion, create a higher level of presencemaking the users more engaged in the activity they are trying to accomplish. These two factors of immersion and presence are what make VR unique and beneficial. VR has some applications and case studies in the industry along with some research being conducted in universities. Unfortunately, there has not been a comprehensive literature review or analysis regarding only VR and its implementations for the mining industry in the last 5 years. This paper aims to describe what VR is and its relation to the mining industry, in the most recent years. The paper first gives a brief background on what VR is and its key concepts. Secondly, it will give information on how the initial stages of the literature review were conducted and the findings along with discussions. The paper will finish with the conclusion drawn from the discussion and potential future work.

Feb 1, 2023

By Martin Langenderfer, Catherine Johnson, Alexander Douglas

Mine haul roads degrade rapidly due to extreme loads on sub-optimal construction materials. Unmanned aerial vehicles (UAV) are suited to quantify large-area road-network conditions, such as surface roughness, defects, and grade to optimize remediation of poor conditions and reduce overall costs. Mine haul roads present unique challenges, such as material type and edge characteristics, to automatic road detection that often fail, requiring manual road input. This research proposes a new method for analysis using the road center determined by principal curve analysis of a haul truck’s Global Navigation Satellite System (GNSS) traces; analysis grids were created from this center line. A dense point cloud from UAV photogrammetry was generated, and multiple linear regression analysis was conducted on each individual grid. The root mean square error in each grid indicates the surface roughness, and the change of slope between grids indicates the road grade inconsistencies. This method was applied to 26 road sections, and the results were validated by images taken from the truck operator’s vantage point. Critical defects were identified including excessive pothole formation, corrugation, depressions retaining water, and narrowing of travel lane. The results demonstrate this is a valid method of road identification and quantification of road defects at a mine site.

Dec 19, 2023

By E. Petrakis, K. Komnitsas

The main objective of batch grinding modeling is the estimation of the product particle size distribution over time or specific energy input to the mill. So far, the developed analytical methods require often complicated calculations which are timeconsuming. Thus, more simple approaches that allow the reliable prediction of the complete product size distribution need to be developed. In the present paper, an approach, based on the population balance model (PBM), that reliably predicts the product size distribution is proposed. In order to enable this, the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (R-R) distribution, thus allowing the determination of the breakage rate for each grinding period. A time-dependent breakage rate framework was developed where the traditional linear theory of the PBM is considered a partial case. This approach allows the deviations from the linear theory to be categorized and the degree of the acceleration-deceleration of the breakage rate to be predicted. Modeling results were validated by laboratory grinding studies using two homogeneous materials, quartz and marble, and one heterogeneous, a limonitic laterite. The experimental data revealed that grinding exhibits non-first-order behavior and the degree of deviation from the linear theory depends on the tested material. The reliability of the proposed model was validated with the use of the distribution modulus n, the a value of the breakage rate parameter, and the optimum n values that minimize the sum of the differences between the experimental and estimated particle size distributions.

Feb 8, 2021

By Theodore S. Jordan

The discovery of a major porphyry-type copper deposit on the Papago Indian Reservation in Pinal County, Arizona was announced by El Paso Natural Gas Company in 1968. The deposit, known as the Lakeshore Property, contained an estimated 470 million tons of sulfides and oxides averaging 0.75 percent copper. History and Geology of the area have been described by Harper and Reynolds (1969). El Paso subsequently&apos; entered into the agreement for joint development of the property with Hecla Mining Company, with Hecla as the operator. The ore body consisted of three types of mineralization: 1) Disseminated Oxide Ore, <1% Cu 2) Disseminated Sulfide Ore, <1% Cu 3) Tactite Ore, >1% Cu

Jan 1, 1985

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Vishal Gupta, member SME, of EP Minerals LLC, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Vishal Gupta, member SME, of EP Minerals LLC, Agricultural Materials.• Joe Garska, member SME, of Imerys, ceramics and refractory materials.• Stanley Krukowski, member SME, of the Oklahoma Geological Survey, chemical raw materials.• Russell Winn, member SME, of R.E. Janes Gravel Co., chemical raw materials.• Justin Zdunczyk, member SME, of Pike Industries, construction aggregates.• Jerry Gauntt, member SME, of Golder Associates, fillers and pigments.• Ebrhaim K. Tarshizi, member SME, of the Michigan Tech, sorbents, filters and process aids.• Daniel T. Eyde, member SME, of St. Cloud Mining, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.Virta, R.L. U.S. Geological Survey, National Minerals Information CenterFour companies - H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. - mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer state accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.ConsumptionIn 2013, domestic ball clay producers sold clays to the following markets: ceramic floor and wall tile (44 percent); exports (21 percent); sanitaryware (18 percent); miscellaneous ceramics (9 percent); fillers, extenders, and binders, and unspecified uses (4 percent each), based on 2012 end use patterns and current markets. Other markets accounted for less than 1 percent of the remaining ball clay sales or use. Sales reported for the manufacture of fiberglass or most filler, extender, and binder applications were likely to have been mainly kaolin mined or purchased by the ball clay producers.PricesThe average value of domestically produced ball clay was approximately $47/t ($43/st) in 2013 compared with $46/t ($42/st) in 2012, on the basis of a preliminary survey of domestic ball clay producers. The unit values of exported and imported ball clay were $126/t ($114/ st) and $373/t ($338/st), respectively, in 2013, compared with $62/t ($56/st) and $314/t ($285/st), respectively, in 2012. Unit values for most large export shipments increased in 2013, and a larger number of low-tonnage, high-value export shipments were shipped in 2013 than in 2012, resulting in a doubling of the average export value. Two low-tonnage, high-value shipments in 2013 accounted for the increased value of imports."

Jan 1, 2014

By AMIR EHSAN KIANFAR, Moritz Ziegler, TOBIAS HARTMANN, ELISABETH CLAUSEN

Accurate positioning information is a central step in the process of increasing automation and digitalization in the mining industry. Underground mine environments are prime examples for GNSS-denied environments that pose several additional challenges for the employed indoor positioning system (IPS). This work presents an ultra-wideband (UWB)–based system specifically tailored for underground mine environments. Initially, the UWB technology is reviewed and basic concepts of IPS are explained. Both software and hardware are described in detail, including positioning algorithms, electrical circuitry, and the mining-compatible enclosure. Finally, the results from field tests in an underground mine are presented and positioning performance and the influence of dilution of precision (DOP) on positioning results are empirically evaluated. The results show that the localization errors are mostly below 1 m. Individual zones of high localization errors are suspected to be caused by noise interference. Significant DOP influence due to the mining drift geometry can be confirmed. The system shows promising localization results for different mining applications, while influences negatively impacting the accuracy are presented as items for future research.

Jul 7, 2023

By V. Svalbonas, S. M. Jones, A. Boughey

In June 1998, the world&apos;s largest grinding mill, the 40 ft (12.2 m) diameter 20 MW Cadia gearless SAG mill, was commissioned. This was a leap of over40% above the largest operating SAG mill. A significant saving in capital cost gave the incentive necessary for a single mill line at Cadia, resulting in the selection of the 40 ft (12.2 m) diameter mill. Now, after 18 months of operation, this paper will review the significant items involved in the development, design, manufacture, installation, and operation of this mill.

Jan 1, 2000

By J. Drew

Oregon Resources Corporation (ORC), an industrial minerals mining company, is currently engaged in the development of a new process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be mined efficiently and economically, creating an additional domestic source for chromite, garnet, and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America. Metallurgical study of the placer material was grouped into four distinct samples based on marine terrace deposition, geological facies, and mineralogy. Because the metallurgical samples represented the extremes likely to be encountered in all future Oregon paleo-beach placer ores, the process design is highly dynamic and will successfully adjust to meet the production needs. Water availability at the mining area is seasonal and will not support a typical placer operation?s water requirement needs for heavy mineral concentration. For this reason, ORC has developed a plan to construct the ore processing facilities near Coos Bay, where a municipal source of water is available. Raw ore will be transported from the mining sites approximately twenty miles one way to the processing facility with return loads hauling tailings back to the active pit. The need to haul dry tailings, return dry material to the pit for reclamation, and limit the amount of water being purchased from the municipality has driven the design of a unique water reclamation system. BACKGROUND Location and Access Economic concentrations of ?black sand? or heavy mineral (minerals with specific gravity greater than 2.85) have been recognized and studied in marine placers from Coos Bay to the mouth of the Rogue River, a distance of approximately 75 miles along the southern Oregon coast (Hornor, 1918; Griggs, 1945)(Figure 1). ORC will begin mining existing reserves approximately 20 miles south of Coos Bay in a region known locally as Seven Devils. Ore will be trucked north to the processing site near Coos Bay via use of existing county and state roads, including U.S. 101. The available facilities at the processing site include highway, rail, municipal water and electricity, natural gas, and a deep water port. At the time of this writing, the rail line had been abandoned, but was being pursued by the International Port of Coos Bay. It is anticipated that this will be serviceable at some time in the future. History The southern Oregon marine placers have garnered the interests of miners since 1852, when present day beaches were exploited for gold. The beach deposits were small and irregular in nature and were easily washed away by the major storms the coast endures during the winter months (Hornor, 1918). [ ] In the 1920?s, deposits at the beach were followed upstream to their paleo-beach terrace origins (Pardee, 1934). These terrace placers were mined, but with little success, as the cost of mining and processing was greater than at the present day beach deposits. The greatest effort to understand and delineate the paleo-beach terrace placers came during World War II. As the need for a domestic source of steel hardening chromite was evident, the heavy mineral bearing placers of southwestern Oregon provided just that. The U.S. Geological Survey, under guidance from the Oregon Department of Geology and Mineral Industries, began exploration drilling of the paleo-beach terraces in 1940 (Griggs, 1945). This work was part of the investigation of strategic mineral deposits and would ultimately supply much needed chromite for the war efforts. The first mining efforts began in 1943 by the Humphreys Gold Corporation and the Krome Corporation (Griggs, 1945). Black sand

Jan 1, 2009

By Peter Dowden, Trevor Carter, Allan Moss, Bruce Downing, Richard Beddoes

Traditionally (with a few exceptions) tunnel boring machines (TBMs) have been utilized on tunnel projects where the risks associated with deep tunnels (rock burst, squeeze, etc) are low (or expected to be low). This has generally been due to the extremely adverse consequences of entrapping or damaging a TBM under such conditions; but also due to the relative difficulty of dealing with these ground conditions in the confined working area of a TBM, in comparison to a drill and blast heading. This paper review the constraints of operating a TBM in a deep tunnel and discusses related project experience, particularly recent and current experience with TBMs in the deep Alpine Base Tunnels. Potential future applications of TBMs in the development of large, deep underground mines are also discussed.

Jan 1, 2007

By Vinícius Resende Domingues, André Pacheco de Assis, Bernardo Cascão Pires e Albuquerque

"The increasing demand for underground works in urban centers, and in particular the need to build undercrossing tunnels, requires constant evolution in building techniques in order to achieve success and safety. In the case of Brasilia, capital of Brazil, in order to preserve an important avenue (Eixo Monumental), where are located many historical monuments, the construction of a tunnel was envisioned as an option to interconnect the National Stadium (on one side of the avenue) to the Convention Center Ulysses Guimarães (on the other side). The excavation design is comprised of a coverage smaller than one diameter, height of 7.5 m, width of 9.0 m and length of 25 m. In order to enable a negligible influence on the avenue’s usage, the structure is designed as a portico system composed of pipe canopy. In this context, this study presents the portico analytical solution computed with the aid of the software Mathematica and a numerical solution using the software ABAQUS. INTRODUCTION Undercrossing tunnels are increasingly common in urban centers as alternative roads or as access to underground works of large dimensions (stations and parking lots). The geomechanical conditions of the soil mass, not always favorable, and the low distance between tunnel’s ceiling and the surface require intense treatment of the soil massif and execution of a rigid support system. The importance of the road just above the undercrossing tunnel emphasizes the need for a highly competent monitoring system because existing structures require minimum allowable displacement and do not allow the interruption of traffic. The soils that are excavated for the construction of undercrossing tunnels are composed, in most cases, of layers of fill and / or soft soil or weak rock, showing stability problems when subjected to tunneling operations. The combination of low coverage and week ground is solved by soil improvement techniques and strengthening of the excavated cross-section with further advance with the so-called New Austrian Tunneling Method (NATM). Another option is to build structural frames that support the surface. In this research, and based on the context of a case study, we propose the study of the construction technique comprising a portico structure composed of pipe canopy. For this paper, the technical standards used are the Brazilian ones as the case study refers to this country."

Jan 1, 2016

By G. B. Amicucci

Golden Sunlight Mines Inc. operates an open-pit gold mine and cyanidation plant about 11km (7 miles) northeast of Whitehall, MT. Golden Sunlight is a subsidiary of Placer Dome US Inc. Mining is accomplished with conventional open pit drilling, blasting and hauling methods. The mining rate is about 102 kt/d (113,000 stpd). Gold occurs as fine-grained disseminations in a pipe-shaped breccia and in immediately adjacent country rock. The ore body is low grade, averaging 2 g/t (0.059 oz per st) of gold. The metallurgical plant uses conventional carbon-in-pulp (CIP) technology. Daily throughput averages 6.5 kt (7000 st). Recoveries are enhanced through a sand tailing retreatment facility while a preaeration process reduces operating costs. The low grade ore dictates that maximum mill throughput at the desired grind size be maintained. Therefore, in October 1988, an Armco Autometrics (now Denver Autometrics) particle size monitor (PSM) 400 was commissioned. The PSM 400 is an on-line instrument. It measures particle size and percent solids in a slurry stream. The PSM pulls its own sample, deareates the sample and passes it through diametrically opposed ultrasonic sensors. The unit uses ultrasonic sound to measure the deareated slurry stream&apos;s particle size and percent solids.

Jan 1, 1991

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021

By Robert D. Thomson

The plastics industry runs into the billions, both in the dollar value of its finished, products and in the pounds of plastic raw material produced. It is, too, one of the fastest growing industries with a 300 percent increase in production in the past ten years. Informed estimates set 5.9 billions pounds as the plastic volume for 1959. Statistically, this is equivalent to a per capita consumption of 25 pounds in the United States. Plastics are man-made materials in contrast to natural materials like wood and are a family of materials -- not a single material - each member having special advantages. A generally accepted definition; for plastics is; a large and varied group of materials which consist, wholly or in part, of combinations of carbon with oxygen, hydrogen, nitrogen, and other organic and inorganic elements. This, while solid in the finished state, at some stage in its manufacture is soft enough to be formed into various shapes, most usually through the application either singly or together of heat and pressure. Many combinations and many different materials are thus possible. Therefore, for purposes of simplification, most plastics can be classified under one of 14 recognized basic family groups. These groups in turn generally can be further classified into one of two major subdivisions - thermosetting or thermoplastics. A few plastics are in between and they can be formulated to be either thermosetting or thermoplastic.

Jan 1, 1960

By Shuie Li, Taibai Li, Tao Hu, Zhongjie Wang, Xiang Ge

As one of the main power sources, lithium-ion batteries (LIBs) will continue to be applied on a large scale in the future market. Commercialized LIBs cathode materials contain various valuable metal elements including Li, Co, and Ni. The development of green and efficient recycling technology is essential. Deep eutectic solvents (DESs) have recently emerged as a new class of green solvents that could potentially be applied for the LIBs recycling industry due to their capability to leach the active materials without the introduction of environmentally hazardous reagents as used in conventional hydrometallurgy process. Considering the rapid progress, a critical review focusing on the progress and fundamentals about the overall efficiency has practical significance for the further advancement of this field. Herein, we briefly introduce the overall process of using DESs for LIBs recycling and specifically focus on the efficiency of each step. Current fundamental understandings and new experimental approaches to enhance the efficiency of the leaching process, the extraction process, and reusability are summarized. We expect this review article to inspire scientists to use DESs as powerful tools for advancing the frontiers of LIBs recycling.

Jul 30, 2022

By John G. Groppo, James C. Hower, Cortland F. Eble, Rick Q. Honaker, Alireza Valian, Stephen F. Greb

Coal and coal combustion byproducts are potential candidates for alternative resources of REEs (rare earth elements). The Illinois Basin is a major coal-producing district in the USA, but little work is available on speciation of REEs in the basin’s coals. In this study, a total number of 382 samples from known locations in the Illinois Basin coal beds were acquired, analyzed for their REE contents, and investigated for any spatial trends or chemical correlations. This study includes Springfield, Herrin, and Baker coal beds—the most heavily mined coals in the basin. An average coal ash from the basin contains 320 ppm REE, with Baker being the highest (407 ppm on average). However, the distribution of REEs in the coal beds was laterally and vertically heterogeneous. A number of trends were found in the REE variations. The most important trend was the relationships of the REE concentrations and fractionations with the distance from the syndepositional sandstones. The total REE concentrations were higher in the proximity of the sandstones, likely due to the increased deposition of detrital material. This increase was the most significant in Springfield coal (90%) and least in Baker (6%). Those coal samples from the Springfield and Herrin coal beds distal from the syndepositional sandstones had a heavy to light REE ratio (H/L ratio) of 0.40 on average, whereas in proximal locations, the ratio was dropped to an average of 0.30. This trend was not significant in the Baker coal bed. In general, higher mineral matter in the coals was associated with higher REEs. In coal preparation plants, refuse rocks can have up to 360 ppmREE. However, the ashes of the cleanest coals had higher REE levels. Such ashes also have a higher ratio of heavy to light REEs. The highest REE concentrations were found in the claystones and the shales associated with the coal beds. Since the naturally occurring calcite, quartz, and pyrite samples were depleted in REEs, an association of REEs with the clay minerals can be suggested.

Jul 20, 2020

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992