Search Documents

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

By Arne M. Myrvang

Rock stress measurements have been carried out by the Mining Department, the Norw. Institute of Technology (NTH) since 1964. Before that time rock stress measurements were carried out at a few locations by the Swedish professor Hast as early as 1958. From the very beginning the NTH engagement in the rock stress measuring field has been very practically aimed, and we have all the time enjoyed a very good cooperation with the Norwegian mining industry. At a very early stage the industry realized that proper measurements with proper equipment could be a very valuable practical tool. Hence the industry also was willing to grant considerable funds for the education of experts and development of measuring techniques. Since 1964 measurements have been carried out in the great majority of Norwegian mines. During the last years a large number of measurements have also been carried out in connection with hydro-electric power plants, road tunnels etc.

Jan 1, 1981

By Mary Nelima Ondiaka, Kayode Henry Talabi, Oladunni Oyelola Alabi, Fatai Olufemi Aramide, Francis Gitau

Iron ore is essential in steel making; however, high-grade ores have diminished, making low-grade ores inevitable. These lowgrade iron ores need further beneficiation to upgrade the iron content. Currently, traditional physical and chemical methods are utilized and are not environmentally friendly. Bio-beneficiation techniques have emerged as a sustainable alternative for mineral recovery. This review delves into recent bio-beneficiation advancements for enhanced low-grade iron ore recovery using microbes. Research has revealed that bio-beneficiation methods such as bio-leaching, bio-flotation, and bio-flocculation have proven successful in iron recovery from ores. The bio-beneficiation process occurs in mild conditions using bio-reagents derived from microbes and offers a reduction of chemicals used in processing. Bio-beneficiation of iron ore potentially offers a relatively energy-efficient, cost-effective, and environmentally friendly method of maximum iron ore recovery. However, this review has identified a scaling-up difficulty in which a future approach for industrial-use applications is offered following a thorough sustainability assessment. Bio-beneficiation, using microbial processes, provides a viable avenue for maximizing iron ore recovery while tackling the constraints of dwindling high-grade iron ore resources and environmental sustainability.

Mar 16, 2024

By Andrew Stafford, Kate Willa Brown Requist, Eric Lutz, Simon Lotero Lopez, Moe Momayez, Jeffrey Gordon

This formal literature review identifies strengths and shortcomings of current literature related to mine rescue, self-rescue, and self-escape technology. Key concepts and factors that influence the decision making behind mine rescue and self-escape were identified. Historically, underground mining has been one of the most dangerous occupations due to the harsh nature of working environments. During the latter half of the twentieth century, and into the twenty-first century, mining fatalities have declined, yet large-scale mine emergencies persist. The emergence of new technologies, in combination with evidencebased mine emergency research, is resulting in new training methods, monitoring systems, and self-escape approaches being tried in operating mines. This review identifies areas in which substantial research is being conducted, such as the use of virtual reality and game-based training and areas that warrant further development such as the measurement and information gathering capabilities of unmanned ground and aerial vehicles, as well as emergency management and incident command systems. This paper summarizes the current underground mine rescue and self-escape landscape in the USA, including the breadth and depth of mine rescue and self-escape training and practices as evident in the literature.

Nov 2, 2023

By Borje Bjorkvall

At LKAB's plants in Lappland, Sweden, sintered pellets are manu-factured according to three different industrial processes, viz. shaft furnace at Malmberget, straight-grate at Kiruna and grate-kiln at Svappavaara. At present the total annual capacity amounts to 4.7 million tons. However, since it has been decided to erect a new straight-grate plant (2.5 million tons) at Malmberget, and because of the decision to extend and rebuild the existing plants, it is estimated that the annual capacity will be increased to somewhat over 8 million tons by 1973. The great majority of the pellets produced is exported. They are thus reloaded several times and generally speaking roughly handled, resulting in larger or smaller product losses on arrival at the point of use. It is there-fore of great economical interest to have a good control over the transport strength of the pellets by appropriate quality testing at the point of production. In addition to good transport strength, further demands are ob-viously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of in addition to good transport strength, further demands are obviously made on pellets destined for blast furnace operation. The blast furnace burden must maintain a good permeability for the gas. The pellets must thus have a favourable size distribution and must not be so weakened by reduction that they disintegrate under the stresses and clog the blast furnace shaft. Furthermore, the burden must have good reducibility. An increase of the rate of reduction can obviously mean increased blast furnace capacity and reduced coke consumption. In order to optimise the properties of the pellets in these respects, the producer must also be thoroughly familiar with their behaviour during reduction, particularly as the customer's interest in the reduction properties of the pellets' has increased over the last few years. Up to now the only quality demands the customer has made have generally had to do with the cold strength and the screen analysis. Thus a quality control of

Jan 1, 1972

By K. D. Dill, S. D. Rosenthal

"This project analyzed the efficiency of incorporating the use of directional drilling technology into coal overburden blasting. Directional drilling is currently in use in the petroleum industry and it is believed that it will be a valuable asset in the mining industry. This project has shown that directional drilling can be a viable technology for use in the coal overburden removal process resulting in increased drill utilization and potential for cost savings. Future work regarding blasting and geotechnical evaluation should be performed to solidify the concept. INTRODUCTION Determine the Potential Drill Utilization Improvements and Rock Fragmentation Requirements Using Directional Drilling in a Coal Mining Overburden Highwall Application was a project funded by Atlas Copco Drilling Solutions (Atlas Copco) based in Garland, Texas. The project was developed and researched by Montana Tech of the University of Montana. This project was intended to show how the use of directional drilling can increase drill utilization, while decreasing costs, without sacrificing overburden blasting results. This paper discusses a review of the literature, the methods performed, conclusions and future work Background Atlas Copco theorized that an alternative approach to drilling a cast blast pattern would be beneficial to coal mining operations by increasing drill utilization and therefore, decreasing overall costs. Increasing drill utilization results in an increase in the amount of time the drill is being productive, more drill bit time in ground. Atlas Copco’s theory is that by incorporating directional drilling in the design of a cast blast pattern, a drill rig could drill multiple directional holes, which are the length of the cast blast, from a single drill set up. A drill goes through a series of steps to complete a blast pattern, these steps include: tramming to the hole location, leveling the drill, drilling the hole, cleaning the hole, and retracting the drill steel. This process is repeated hundreds of times until the whole pattern is completed. The most time intensive part of this process is drilling out the blast pattern. Integrating directional drilling into this process could decrease the overall time it takes to drill out a blast pattern by minimizing the amount of time spent tramming and setting up for each subsequent hole. Tramming and drill set up are two aspects of the drilling process where the drill tool is not engaged with the ground and, therefore, not being utilized. A cast blast pattern designed to utilize directional drilling will allow the drill tool to be “in the hole” longer and will improve drill utilization. This change in drill utilization was analyzed. Drilling and blasting is an integral part of the mining process, without it mining would be a slower process and less material could be mined. Drilling provides holes for explosives to be loaded and then blasted. Blasting has been found to be the most cost effective method of fracturing rock in mining for material removal. Blasting is also used as a low-cost method to move the rock in open cast mines, commonly referred to as cast blasting. A cast blast is a large blast designed to allow for the maximum amount of overburden to be removed using explosives in a single blast thereby uncovering more coal at a lower cost. Not all the material is blasted to cast-to-final, which requires that material to be moved with large mining machinery. Material that is considered cast-to-final is material that has been thrown far enough to never be moved again in the coal extraction process, therefore it is in its final resting place. A typical cast profile and cast-to-final area is shown in Figure 1."

Jan 1, 2017

By D. Robert Weir, M. J. H. Ruscoe, R. M. Berezowsky, M. A. Clegg

The metallurgical processing involved in the produc-tion of the new Canadian one dollar coin is reviewed starting with the hydrometallurgical production of pure nickel powder, followed by the powder metallurgy process for the production of nickel strip and coinage blanks, and concluding with the Aureate bronze electroplating and heat treatment procedure. Coinage requirements are then reviewed with regard to economic, public acceptance, and service requirements. Finally the properties of Aureate nickel coinage are presented in the light of the many and varied coinage requirements, and it is concluded that the new Canadian dollar coin exceeds the requirements admirably.

Jan 1, 1990

The mining industry, like most other industries, has had a difficult couple of years. What are your thoughts on the industry?s direction in the next few years? I am bullish on our industry. There is no question in my mind that the quality of life we enjoy today is largely a result of our past successes in the minerals and mining sector. I am equally certain that the sustainability of that quality of life and the aspirations of the rest of the world to attain that same level of lifestyle will depend hugely on our future successes and will be the driver for our industry to continue to excel and prosper. Surely, there are going to be challenges along the way. These challenges are not only from the public, regulators and various governing bodies, but also from our industry?s own self regulating efforts. However, we have demonstrated throughout the past several decades that we have the capability to meet these challenges head on and come out ahead.

Jan 3, 2010

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

By R-H Yoon

The MicrocelTM column flotation technology has been developed based on the fundamental understanding that the first-order flotation rate constant increases approximately as the inverse cube of bubble size. In this technology, bubbles in the range of 100-400 pm are generated by pumping aerated slurry through an in-line static mixer. The high-shear agitation provided by the in-line mixer produces small air bubbles without requiring large frother additions. This column has been tested successfully for processing a variety of non-metallic minerals including kaolin clay, graphite, phosphate, and feldspar.

Jan 1, 1993

By C. Flores

The most common experimental approach of studying one variable at a time while holding all others constant is extremely inefficient. Use of statistical methods enables engineers and scientists to obtain meaningful information with the fewest experiments, reducing cost and wasted effort. In particular, the Taguchi method can be more efficient than traditional full factorial experiment designs, as it can study more variables with fewer nuts, and it is more robust against process "noise." Taguchi designs are also simple to formulate and the results can be analyzed by simple PC spreadsheets. The role and benefits of using the Taguchi method in experiments to develop and optimize processes is discussed.

Jan 1, 1998

By R. C. Troxell

Alternative methods of analyzing data acquired by the Morenci copper concentrator process control instrument-computer system are presented. Experimental measures of ore characteristics, for proposed feed forward control, are introduced. These include on-line indexes of ore hardness, ore density, ore dusting, and ore color. Comparison of metallurgical results before and after computerized process control implementation, allowing for differing ore grades, oxidation, hardness, and fineness of grind, also is described.

Jan 1, 1979

By R. L. Grayson

Focusing on relationships between severity measure versus productivity and other factors, this paper presents a comprehensive study of injuries for U.S. underground coal mines in 1996 by mine size. Based on analyses of data, generally the larger the mine, the more productive it is (in tons per employee-hour), but the more severe is its injury experience (r = 0.65). Within very large, large, and medium mine sizes, however, the more productive the mine, the less severe is its injury experience (r =-0.43, -0.36, and -0.26, respectively). For small and very small mines, a more deeply nested analysis is required to understand relationships. Other interesting relationships and comparisons are presented.

Jan 1, 2000

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By Jay Nopola, Christopher Johnson, Matthew Minnick, Erik Hemstad, Erik Walega

Mining data collection, storage, and interpretation methods have progressively changed over time. Data collection, for the most part, has transitioned from handwritten notes and logs based on manual gauge readings to real-time data streaming through instrumentation capable of directly communicating with site-based data historians or cloud storage. Data collection and storage have had to adjust commensurately with the volume of data, leading to more complex database architecture. Geoscience interpretation methods have also changed; however, the first goals of modeling and understandings from first principles remain the same and are typically deeply rooted in historical academic work. Machine learning methods are becoming more common, available, and implemented by industry and practitioners. Despite the wide accessibility of machine learning methods, the population of geoscience subject matter experts in the underlying theory of this analysis type is limited. This form of analysis, therefore, must be conducted carefully and in conjunction with subject matter experts, on both machine learning theory and the field it is being applied to. This paper aims to provide background history on data analytics and machine learning, current methods and practices, and high-level geoscience case study examples, as well as take aways regarding the mining industry, potential pitfalls specific to geosciences, and possible perspectives on the direction of artificial intelligence in the future.

Jun 25, 2023

By Qingqing Huang, Mohammad Rezaee

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the 12th MPD Student Poster Contest on March 2, 2022, during the MINEXCHANGE 2022 SME Annual Conference & Expo. The event showcased the work of 32 graduate and undergraduate students from U.S. and international institutions. The contest began in January when the students submitted one‐page abstracts for judging. In February, they prepared and presented posters that explained their research, and each student had five minutes to explain their research to a panel of judges during the conference. Recognizing the students’ efforts in working hard on their research topics and setting aside time to complete the necessary steps to enter the poster contest, the MPD provides monetary rewards to all participants. For graduate students, first place receives $1,000, second place $500, and third through seventh places $200 each, and for undergraduate students, first place receives $1,000 and second place $500. The main authors of nonplacing entries receive $125 each. Participation in the contest includes a free ticket to the MPD Luncheon, where the winners are announced.

Nov 22, 2022

By R. Barthel, O. Nitzsche, J. Pateiro Fernández, T. Cramer

The Hong Gai coal field in northeast Vietnam has been the main coal mining area of Vietnam for more than 150 years. Anthracite coal is produced from several open pit and underground mines situated close to the UNESCO world natural heritage site Ha Long Bay. The mining-induced environmental impacts such as dust emissions, acid mine drainage, and visual impairments due to waste dumps resulted in severe conflicts of interests regarding future land use and the protection of the world natural heritage site Ha Long Bay. Within the RAME project (Research Association Mining and Environment in Vietnam), Brenk Systemplanung is contributing to an improved environmental and sustainable planning in Vietnam's mining industry and the reduction of environmental impacts on Ha Long Bay by developing suitable and sustainable technology and planning measures (e.g. for dump construction/rehabilitation, predictive modelling, and/or monitoring) for Vietnam's leading coal producer.

Jan 1, 2011

By Juan J. Monsalve, Mario Karfakis, AMAN SONI, Nino Ripepi, Jim Hazzard

Pillar collapses are events that due to their severe consequences can be classified as high risk. The design of pillars in underground room-and-pillar operations should migrate to risk-based design approaches. The authors of this work proposed a risk-based pillar design methodology that integrates stochastic discrete element modeling for pillar strength estimation, and stochastic finite volume modeling (FVM) for stress estimation. This paper focuses on the stochastic FVM component for stress estimation. The mining and geomechanical aspects of a case study mine (CSM) are described and pillar stresses are estimated by using three approaches: (1) analytical solutions, (2) 2D finite element modeling, and (3) 3D finite volume modeling. This operation extracts a 30° dipping deposit, which makes current underground stone mine design guidelines inapplicable for this CSM. This work compares results from each stress estimation approach and discusses uses the point estimate method as a simplified stochastic approach to evaluate the effect of rock mass elastic properties variability on pillar stress distribution. Results from this work show that the three estimation approaches lead to different estimations, possibly, due to the wide range of assumptions each estimation approach considers. It was also determined that the horizontal to vertical stress ratio has a significant impact on pillar stress magnitude. Therefore, it is recommended to perform in situ stress measurements, or assume worst-case-scenario values to account and reduce uncertainty due to this parameter. The stochastic stress estimation approach used in this paper provides results that can integrate a risk-based pillar design framework.

Sep 24, 2022

By Richard E. Gertsch

If you believe that the goal of the space program should be a permanent, manned presence in space, then you believe in space mining. Historically, mining has been an integral part of the frontier. For the space frontier, mining is absolutely necessary. Any large-scale space facility must be built from materials mined in space. The reason is simple: the cost of getting material off the earth overwhelms all other costs. The cost of launching a pound of material from earth into low earth orbit ranges from $5000 to $10,000. Multiply this number by three to get to geostationary orbit. With the added expense of landing on the moon, an object is worth more than its weight in gold. Most space projects are impossible if materials must be hauled out of earth's enormous gravity well. For example, habitats (large structures in free-fall that simulate earth's gravity) and massive solar power satellites will take millions of tons of material to construct. Transportation economics alone dictate space as the source for oxygen, construction materials, and metals, among others. Space mining is not concerned with introducing materials for terrestrial use. The need for materials in space is infinite. The challenge for the mining industry is enormous.

Jan 1, 1991