Search Documents

By Carrie Pourvahidi

The California High Speed Rail Authority (Authority) was created by the State of California through legislation in 1996. The purpose of the Authority is to plan, construct, finance and operate a statewide intercity high speed passenger rail system. In 2004 the Authority prepared a programmatic level environmental document in compliance with the California Environmental Quality and National Environmental Protection Acts (CEQA and NEPA).The Authority and Federal Railroad Administration (FRA) were the lead agencies overseeing the development of the environmental documentation. The resulting document includes two volumes and 64 supplemental technical reports analyzing the transportation needs for California and the selection of an approach to meeting the project transportation needs. The Programmatic Environmental Impact Report and Environmental Impact Statement (EIR/EIS) identified High Speed Rail as the most environ-mentally protective, sustainable and economical approach to meeting the state?s projected transportation needs.

Jan 1, 2008

By E. H. Cho, B. Conner

Three sulfide minerals, chalcopyrite, sphalerite, and pyrite, were leached using a bioleaching mode and an electrobioleaching mode. The former mode was used to leach the minerals with the bacterium A. ferrooxidans in a bioreactor. In the latter mode, the leaching of the minerals was performed in a combination of a bioreactor and an electrochemical cell. In this set-up, the solution was circulated between the bioreactor and the cathode compartment, the two reactors were in series, and the cell was operated intermittently. The mechanism is such that an increase in Fe(II) concentration, which is a nutrient of the bacteria, by electrochemical reduction of Fe(III) would increase the bacterial population and in turn would accelerate the leaching of the mineral. It has been found that the electrobioleaching of chalcopyrite is an improvement over the bioleaching with respect to the fact that leaching conversion is higher and a high level of Fe(II) concentration can be maintained. However, the electrobioleaching of sphalerite does not show any improvement over bioleaching. The electrobioleaching of pyrite is similar to that of chalcopyrite, and this has potential to be used in applications such as coal desulfurization and pretreatment of refractory gold ore in heap leaching where fine gold particles are entrapped inside pyrite particles.

Jan 1, 2006

By Steve Kral

The upswing in prices for base and precious metals, industrial minerals and coal has allowed the global mining industry to ramp up production at existing mines and begin construction of proposed projects. In addition to satisfying shareholders, the industry is also providing good paying jobs and creating needed infra-structure in places that previously did not have either. However, the industry has learned that the prospect of jobs and infrastructure is not necessarily a guarantee that communities will allow mines to be built. The industry must maintain even higher environmental and reclamation standards. And mining companies must help communities plan for life after a mine is closed and the company moves out.

Jan 1, 2005

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), the authors showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/tonne of REEs occur in AMD and AMDp respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. Geospatial analysis identified a total resource of 340 tonnes stored at the 141 sites sampled in this study. While this analysis did not quantify the basin-wide REE inventory, it does indicate the impact that processing cut-off grades will have on the overall AMDp resource base.

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), the authors showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/tonne of REEs occur in AMD and AMDp respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. Geospatial analysis identified a total resource of 340 tonnes stored at the 141 sites sampled in this study. While this analysis did not quantify the basin-wide REE inventory, it does indicate the impact that processing cut-off grades will have on the overall AMDp resource base.

By C. H. Bucknam

Classical acid-base accounting using modified Sobek titration methods has resulted in interpretation of results for materials with neutralization potential (NP) less than 20 tons of CaCO3/1000 tons of material (2% CaCO3) as "uncertain" due to lack of sensitivity within that content range. Standardization of a "fizzless" acid neutralization potential (ANP) method was undertaken in the American Society for Testing and Materials (ASTM) International using two ranges of sulfuric acid additions based on reaction pH and carbonate carbon estimates rather than subjective fizz testing as well as hydrogen peroxide additions to correct for mineral acidity. The method is identified as the acid neutralization potential acidity (ANPA) titration method. During interlaboratory testing a positive bias was discovered within the "uncertain" range which was further investigated and resolved by increasing the test sample weight from one to five grams for samples needing improved accuracy in materials with ANP <2% CaCO3. Test results from the interlaboratory testing of the low range method is presented and compared with the results from the original ANPA method in the paper.

Feb 27, 2013

Seven legendary figures of American mining will be enshrined in the National Mining Hall of Fame in ceremonies on Saturday, Sept. 7 at the Little America Hotel in Salt Lake City, UT. The 15th annual induction banquet will begin with a reception at 6 pm, followed at 7 pm by the dinner and the program. Of the seven inductees, one is living. He is Alexander Murray (Bud) Wilson, 80, of Los Altos, CA. Wilson led Utah Construction (later Utah International) to become one of the world’s most diversified and successful mining companies in the 1960s and 1970s. It was acquired by General Electric in 1976.

Jan 1, 2002

By E. Giama, A. Macridis, A. M. Papadopoulos

ISO 14031 is an international standard that describes a process for measuring environmental performance evaluation by setting quantitative indicators and providing a structured approach for organizations to follow, independent of location, size, complexity and type of activity. It is not a standard for certification as ISO 14001 is, but it fits into the ISO 14000 series of standards and is intended to assist organizations to apply environmental management systems and obtain environmental evaluation. This case study’s main objective is to identify the interaction between ISO 14031 and ISO 14040-42. ISO 14040-42 is referring to Life Cycle Analysis (LCA) methodology. More specific, LCA is applied (based on the ISO 14040-42 standard) to stone wool’s production, the market dominating thermal insulation material, produced by bauxite and amphibolite. LCA is used as a decision making tool for the development of environmental indicators (based on ISO 14031 guidelines) and for environmental performance evaluation.

Jan 1, 2005

By S. M. Jasinski

Peat is a natural organic material of botanical origin. Peatlands are situated predominately in shallow wetland areas of the Northern Hemisphere. Commercial deposits are formed from the gradual decomposition of plant matter under anaerobic conditions for about 5,000-years. In 2004, peat was harvested in 16 states. Florida, Michigan and Minnesota accounted for more than 80 percent of the U.S. production. Reed-sedge was the dominant variety of peat harvested in the United States, comprising almost 80 percent of the output. This was followed by humus, hypnum moss and sphagnum moss.

Jan 1, 2005

By S. Solar, G. Tiess, K. Nielsen, H. Wagner

The paper summarises the results of a recent study of minerals planning policies of the Member States of the EU. The study has shown that contrary to the public opinion the production of industrial minerals and construction minerals is significant the former accounting for about 20 percent of global production, the latter amounting to about 3 billion tonnes per annum. In contrast the importance of metal ores has diminished although metal production in some European countries can still be significant. The study revealed that very few Member States have clearly defined mineral policies. Common to most mineral policies is the emphasis on reducing minerals consumption and recycling whereas the important aspect protecting access to minerals resources is not adequately addressed by most policies. Access to mineral deposits is regulated in most Member States by land use legislation and administration. Information on mineral deposits in land use planning data bases tends to be scarce. This together with the absence of formal mineral policies places minerals at a disadvantage in land use decision making. The emergence in the recent past of environmental legislation and in particular environmental impact assessments has had a crucial effect on the duration of the authorization process for new mineral projects. Examples are given how minerals planning is handled in some of the Member States.

Jan 1, 2005

By I. Nimmo

Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. Communications issues were resolved, better coordination of materials, improved situation awareness during startups, abnormal operations and an opportunity to make improvements during normal operations characterize the changes at the Worsley Refinery. This presentation will review the reasons for the change. Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. This presentation will review the reasons for the change, what changed and the process of changing the culture from reactive to predictive and what difference that has made.

Jan 1, 2011

By Marvin V. Damm, Lloyd C. Venburg, Dan Sokol

Analytical and computer models are used to evaluate information obtained from existing data and investigation programs so mine water control systems can be designed and developed. These models allow the geohydrologist to predict the amount of groundwater inflow and the impact of dewatering and stream diversion on the hydrologic regime, and to determine the schedule and equipment needed for mine dewatering. This article describes uses of the model and the essential components necessary to construct an effective and practical one. Hydrologic models are constructed to determine the extent that mining activities will affect the ground water and surface water hydrologic regime. These models range from basic analytical, mathematical models to the more sophisticated finite difference and finite element groundwater models. Many factors determine the degree of sophistication, including the mining stage, the complexity of the hydrologic regime, the mining process, and regulatory requirements. Model Uses The geohydrologist and engineer construct models so the entire ground and surface water handling and supply system can be integrated and optimized. These models can provide the following data: • Information for water balance studies-the entire hydrologic regime for the area, including precipitation, transpiration, evaporation, infiltration, runoff, and the effect of geologic features. • Data on seepage rates during mining. • Information to design the depressurization and dewatering system, including water well spacing, location of sumping systems, need for grout curtains, and possible horizontal drain and underdrain locations. • Data needed to schedule dewatering and mining operations. • Prediction of initial and long-term impacts of mining and dewatering, including local and areal drawdowns, effects on existing wells, and modifications to the surface-subsurface hydrologic regime. Potentiometric surface maps and hydrographs can be prepared from these data. • Prediction of the effect of discharge from the water control system on the surface hydrology and data input to design systems for water discharge, storage, recharge, or reinjection. The results of a computer study that illustrates the effect of dewatering and reinjection into an aquifer to confine the cone of depression are shown on the accompanying figure. • Information to forecast potentiometric surface recovery after mining ceases. The accompanying figure shows the pumping and reinjection rates in a program that is adequate to dewater a mine and permit the recovery of potentiometric levels to approximate premining levels after mining ceases. • Documentation and design information for monitoring systems to be installed during all mining phases. • Water quality predictions and geochemical changes, including the possibility of brackish or saline water intrusion because of extensive dewatering or depressurization operations. • Documentation and data for acquiring permits from regulatory agencies. Model Input Program For any model to be effective, detailed hydrologic and geologic data must be gathered from a review of existing information and from an investigative program. These data should cover entire model limits. Data updating, revising, and refining should occur as new information is received from the investigation and monitoring programs, and from the mining operation as it progresses through the pre-mining, mining, post-mining, and reclamation

Jan 8, 1982

By Donald D. Murphy

My first contact with underground, bolt conveyors came when I was hired as a draftsman by the La-Del Conveyor & Manufacturing Company in 1935. At that tine relatively few nines were using haulage belt conveyors. Wore they were in use, they were usually loaded by chain or shaker type room conveyors which in turn were hand loaded at the working face. Duo to the low room tonnage, a gathering belt might receive who output of from six to eight rooms. For several years belts 26 and 30" in width were the favorites for coal mine use. Belt speeds very seldom exceeded 200 ft. per mm. at that time. Conveyor lengths for the majority of units lay between 1.000 and 2000 ft. For a number of years 25 H.P. drives were adequate for those conveyors. From 1940 until about 1950 loads and speeds went up slightly and 40 H.P. drives became the standard. Since the majority of mines were then using direct current power systems, we were able to use controllers with 3 or more steps of starting resistance. The slow belt speeds coupled with relatively long starting cycles kept the rate of acceleration low and gave us smooth, easy starts.

Jan 1, 1963

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation, which often requires that the primary ventilation system is upgraded with additional shafts and surface fans. The use of booster fans underground is a potentially practical alternative. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room and pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By J. Darlington, A. K. SenGupta

Water-swellable layered silicates, namely, the smectite clays can remove suspended materials (called herein as debris) and metal ions from aqueous streams. The present study shows that the flocculating and metal extracting abilities of smectite clay-based flocculants can be enhanced when these clays are used in conjunction with a specific anionic polymer. Such performance enhancement is attributed to the following: i) the clay-dispersing ability of the polymeric additive, that would translate into an increase in the clay-surface area available for the attachment of the debris particles onto the clay particles; ii) the possibility of dispersant-to-coagulant transition of the polymer during the later instants of the treatment process, as a result of reduction in solvency of the wastewater for the polymer due to the release of cationic species from the clay-based flocculant solids; iii) metal-complexing ability and adsorption properties of the polymer.

Jan 1, 2002

By Richard P. Graff

Author?s note: Diversity in practice exists in the application of Generally Accepted Accounting Principles (GAAP) for purchase price allocations with respect to the recognition of Value Beyond Proven and Probable Reserves or VBPP, as defined by the Emerging Issues Task Force (EITF) in EITF 04-3: ?Mining Assets: Impairment and Business Combinations?. This diversity appears to arise from differing interpretations of what constitutes sufficient information to value components of VBPP in business combinations. Concerned with this diversity in practice, respected members of the mining community formed a working group which prepared an issues paper that discussed this diversity and provided recommendations for recognition and valuation of VBPP in business combinations. The working group then submitted this paper to the EITF, requesting further guidance be issued on the concept of VBPP. In conjunction with the submission to the EITF, the working group also provided this paper to the United States Securities and Exchange Commission (SEC) for review and comment. The EITF discussed this issue at its May, 2008 agenda committee meeting. However, it declined to add this topic to the EITF agenda for further consideration. Absent additional guidance on VBPP from the EITF, the working group submitted a proposed definition of VBPP to the U.S. Securities and Exchange Commission for its consideration. The following article, which is consistent with the issues paper that was submitted to the EITF and the SEC, discusses the components of and valuation techniques for VBPP. The correspondence with the U.S. Securities and Exchange Commission, which includes the proposed definition of VBPP by the working group, is attached as Appendix 1 to this article.

Jan 1, 2008

By R. C. Bratton, R. Q. Honaker

Hindered-bed separators are recognized as low-cost, high-capacity devices for both classification and density separation; however, since their inception, there have been few significant advances in the fundamental technology. Recently, Eriez has shown through modeling and pilot-scale testing that the innovative approach to feed presentation offered in the CrossFlow teeter-bed separator provides improved metallurgy when compared to traditional hindered-bed classifiers or single-stage coal spirals. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Most recently, a side-by-side industrial scale evaluation has verified that this technology improves overall efficiency and simultaneously reduces the separation cut-point. With regards to coal processing, data from full-scale units indicate that the CrossFlow offers good separation efficiency, high unit capacity, and metallurgical results consistent with laboratory- and pilot-scale separators.

Jan 1, 2006

By V. I. Kefeli

Public-private partnership efforts are working to create green landscapes from abandoned industrial sites. Fabricated soils, potentially an essential element of such landscapes, are designed to substitute for topsoil on the areas free from ground cover and plant community. The aluminosilicate matrix and humus form the soil micelle - the primary unit of any soil complex. Humus formation is a process based on carbon-nitrogen interaction. Sources of carbon can be materials rich in easily composted products like cellulose and polyphenols (plant leaves) or aged lignin polymers (saw dust from different woody plants). The pathways of carbon-nitrogen complexes are discussed. Properties of the fabricated soil components were examined by bio-tests and plant models.

Jan 1, 2002

By J. Hunter, E. Jackson

This paper describes work done by Placer Dome Technical Services Limited, a subsidiary of Barrick Gold, and Nautilus Minerals Inc. in support of the conceptual design of a subsea mining system. It describes an overall concept design plus specific studies into mechanical excavation at depth. The concept design includes one or more subsea excavators connected to a suction riser, which transports the cut material to a shipboard dewatering and offloading system. A multi-phase investigation was performed into the mechanical excavation of seafloor massive sulphides at depths of around 1600m. Rock samples were recovered and tested for rock properties and cutting behaviour. A small pick drum cutter was procured and tested on a representative concrete slab in a lab and tested again while submerged in a test tank. Finally the cutter was tested on a massive sulphide ore body at 1600m depth. The cutting performance results, e.g. pick forces and specific energies, should provide valuable input to the design of future full scale subsea mining systems.

Jan 1, 2007