Search Documents

By Harry E. LeGrand

The purpose of this paper is to outline briefly some basic principles of ground-water hydrology that have application in mine hydrology and to suggest that an understanding of these principles can help to forestall problems that are internal as regards mining operations and external as regards damage or harm to surrounding areas. The development of a mine below the water table pleads for accurate values to answers of hydrologic problems. Such internal problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required mining or milling use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by homogeneous rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where rocks are not homogeneous. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground-water occurrence and movement should be helpful to mine operators. Mining operations that extend below the water table disturb the natural hydrologic regimen. Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine, The behavior of the cone of depression, as it tends to deepen and to increase in areal extent when the mine is deepened, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised. The geologic and hydrologic settings of mines range greatly so that a simple standard procedure for dealing with problems

Jan 1, 1972

By Louis M. Schlesinger

KMG Minerals, Inc., a mica-feldspar-quartz producer in Kings Mountain, N.C., uses about 50% of its plant's -200 mesh slimes to manufacture brick. However, the company is unable to market the remaining 50% of this fine mineral mixture. The NCSU Minerals Research Laboratory operated a pilot plant to process these slimes to produce an additional product. The process, consisting of blunging and hydraulic sizing, was designed to separate a kaolin-enriched -270 mesh product from the bulk of the coarser +270 mesh "grit" minerals. Size analysis showed that this product was 80% finer than 20 microns and 50% finer than 6 microns (in equivalent spherical diameter). An evaluation indicated that it is a hydrous aluminum silicate that might be suitable in the filler and extender markets for traffic paint, some types of plastics, joint cements, and dusting compounds. Because of its high viscosity, it will be difficult to use more than a small percentage in cast ceramic bodies. However, it might be possible to use up to 10% in extruded ceramic bodies (i.e., electrical porcelain). The 15.2 cm (6 in,) diameter Linatex Hydrosizer was tested using a range of teeter water flowrates, so that the net rise velocity was varied from 0.10 cm/s to 0.40 cm/s. The solid feed rate to the sizer was maintained at approximately 1.1 t/hr/m2 (0.12 ton/hr/ft2). Tests were run using both "shallow" (i.e., 6 in.) and "deep" (i.e., 15 in. teetered beds. The best overall result was obtained when the sizer was operated with the "deep" teeter bed and a net rise velocity of 0.10 cm/s. About 97% of the +270 mesh material was rejected and approximately 79% of the -270 mesh material was recovered in a 14% solids slurry.

Jan 1, 1994

By Christopher Mark

Sixty years ago, underground coal mining was the most hazardous job in the United States. Roof falls were a big part of the problem. They killed about 100 miners every year, more than all other causes put together. Fast forward half a century to 2016, which is the first year ever with zero roof fall fatalities. Just three miners were killed by roof falls during the following 6 years. How was this historic goal achieved? This paper starts with a modern analysis of the causes of the roof fall fatalities in 1968. Then it follows the reductions over time by category, using snapshots of the fatalities occurring in subsequent decades. Along the way, it evaluates the influence of the regulatory environment, changing mining methods, and better ground control technology. The paper shows that in 1968, more than half of roof fall fatalities at large mines were attributable to an inadequate safety culture. The immediate effect of the 1969 Coal Mine Health and Safety Act was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof control plans, which the U.S. Bureau of Mines had been advocating since the 1920s, played a significant role throughout the process.

Jul 1, 2023

By Renee Royer, Allan Punkkinen

As mines progress to ever increasing depth, new challenges are encountered with serious concerns for rock excavations in highly stressed conditions. New procedures have been undertaken or are under way to remove workers from the workface, mitigating risk and exposure to hazardous conditions. Rockbolting crews are at particular risk as they are the first line of defense in the installation of the ground support systems. One such initiative for removal of workers from danger has been with remote bolting. Equipment manufacturers have had the ability to remotely inject resin pneumatically into boreholes for several years, but it has not been recognized as a very effective method due to a variety of complications. This makes the installation of dynamic support system components such as the D-Bolt® increasingly difficult. More recently, hollow-core bolts have become popular providing far more effective installation when installed with pumpable, two component urea-silicate injection resins. Normet has developed high energy dissipation self-drilling dynamic bolts (SDDB®) to meet these challenges. Following several inquiries as to the effectiveness of pumpable resins for use with dynamic support components, Normet Canada performed comprehensive testing of the bolt and resin system at CanmetMINING in Ottawa to dispel or substantiate any preconceived beliefs. Several dynamic and static tests in direct and indirect loading were carried out. Results include tests in shear and early strength UCS of the resin to measure the performance of the SDDB compared with the established D Bolt as an effective dynamic ground support component. Underground field observations, installation methodology and in-situ testing are investigated.

Apr 26, 2022

By W. W. Harvey

The work to be described was part of an exploratory research program directed toward identifying potentially useful but little known reactions in extractive metallurgy. In particular, the major copper sulfide minerals, as a group, have long been considered insoluble in nonoxidizing acids (e.g. Forward and Barren, 1J60; Parsons and Ingraham, 1970; Peters et al. 1972). This generalization was considered to include nonoxidizing conditions in warm aqueous MC1 solutions (Ingraham et al. 1972) and, indeed, was consistent with our own chemical and mineralogical experience. On the other hand, under hydrothermal conditions, copper and sulfide species are carried in solution and deposited as sulfides in mineralized veins. The question that poses itself is: what are the mildest conditions of temperature and fluid composition under which commercially important copper sulfide minerals can be solubilized in the absence of an oxidizing agent? A reference to H2S formation during oxygen-sulfuric acid pressure leaching (Warren, 1958) of chalcopyrite, when the oxygen partial pressure was allowed to fall, provided a clue. In the present study, experimentation with chalcopyrite concentrate in dilute hydrochloric acid, under re flux conditions (in Pyrex flasks) and with an inert purge gas, revealed substantial amounts of H2S production and iron solubilization, cite negligible copper solubilization, after 2 ½ -4 days. Under comparable conditions the extent of reaction with dilute sulfuric, acetic and phosphoric acids was markedly less.

Jan 1, 1976

By Joseph A. Dos Santos

The largest TBM (Tunnel Boring Machine) tunnels are typically along modest slopes, but not always. Occasionally high slope angles are required beyond the capabilities of conventional open trough trailing conveyors. A 2019 project required a large TBM to ascend to an incline angle of 25°. A Sandwich Belt high angle conveyor could easily solve the high angle conveying problem but such a system must include all of the features of the conventional trailing conveyor, particularly the ability to extend with the TBM advance. The writer responded to the challenge and developed a TBM trailing Sandwich Belt high angle conveyor with all of the needed features. The invention (U.S.A. patents awarded October, 2021 and November, 2022) however goes beyond the 2019 project requirements and extends to any high angle incline. This writing first presents the broad Sandwich Belt high angle conveyor development, then its use in various construction and tunneling projects prior to this TBM Sandwich Belt trailing conveyor invention. Finally we present the new TBM Trailing Sandwich Belt high angle conveyor with all of its features and implications.

Jun 13, 2023

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By Roy A. Grancher

Construction materials indeed face a dilemma...as does the building industry as a whole. A stop & go economy; a severe drop; in housing starts; lingering indecision over just what corrective steps are to be taken or to their degree of commitment; no less basic disagreement in regard to which of the, Nation's problems is really the most pressing -- inflation or recession? Optimism has become a rare quality these days. At moat the cautious view is that this new year will see a long, hard struggle back, with hopes that 1976 at least can truly mark a dual anniversary celebration for the United States and its economic health. Yet the paradox is that once recovery does return, those very construction minerals and materials --which in recent years have experienced the ups and downs of overcapacity, shortage, and now declining demand again-- will once more face the spectre of mass inability to service revived and growing needs for its product. Mounting costs, present marginal expansion investment, and substantial lead times required for new facilities to come into production, could well form a bottleneck to economic upswing. The result again can be another cycle of shortage-induced inflation, and with it continued gyrations within the demand supply relationships of the country's building industries.

Jan 1, 1975

By Denis Tepavac, Mark Trim

Structural performance of fiber reinforced concrete (FRC) depends on its ability to carry tensile forces after cracking. Australian Standards AS5100-2017 and AS3600-2018 are the only available design standards that establish a test procedure to determine strength and toughness of an FRC in direct tension. Direct tensile testing of fiber reinforced shotcrete samples was performed to determine if the model and guidelines in AS5100/3600 were applicable to shotcrete; all previous testing was from cast samples. In addition to direct testing, micro CT-scanning was also performed. The paper presents tests performed, results, and how the tests could be used on future projects. In addition, a brief summary is provided of the guiding structural mechanics used for estimating residual tensile strength and test methods utilized to verify those estimates.

Jun 13, 2023

By A. C. Barlow

The use of deep wells for waste disposal is not a new technique. The production phase of the oil industry has been using this method to dispose of unwanted oil field brine since the 1930's The adoption of this method by other branches of industry, however, to dispose of manufactured wastes is a relatively new development, but one which is finding increased use (2). Deep well waste disposal is not an ordinary technique even though it is finding relatively wide application. In fact, just the opposite is true; it is still a rather extraordinary measure. It is not now, nor is it ever likely to be a disposal method which can be assured of success before it is tried.

Jan 1, 1964

By Valérie J. Bertrand, Richard W. Lawrence, Marcos G. Monroy

Two cemented paste backfill (CPB) formulations containing pyritic tailings were leached in deionized water in flooded and alternating air-flooded environments and in a simulated acid rock drainage-type (ARD) solution. Scanning Electron Microscopy (SEM), solid phase chemistry and acid-base accounting measurements documented the weathering characteristics of the CPB samples. Short-term exposures of the portland-CPB samples preferentially dissolved the cement binder to a greater extent than slag-Portland CPB mistures. In all cases, the added neutralizing potential provided to backfill by cement was short-lived and insufficient to neutralize the acid generating potential of the mixture.

Jan 1, 2000

By M. L. Bricker

The Jim Bridger Mine is operated by Bridger Coal Company and is located in Sweetwater County, 35 miles (56 km) northeast of Rock Springs, Wyoming (USA). The general location of the mine site is shown on Figure 1. Bridger Coal is a joint venture of NERCO Coal Corp, the operator, and Idaho Energy Resources Company. The permit boundary encompasses in excess of 20,000 acres (81 km2) and is nestled against the western side of the Continental Divide. Production started on July 3, 1974, and the mine has produced approximately 90 million tons (82 million t) while moving approximately 450 million cubic yards (344 million m3) of virgin earth. Annual production averages 5 to 7 million tons (4.5 to 6.4 million t) of run-of-mine coal. Coal is consumed on site by the Jim Bridger Power Plant, a 2,000-megawatt generating station, and the electricity is transmitted to the Pacific Northwest power grid (Oregon, Idaho, Northern California, etc.).

Jan 1, 1991

By H. Colijn

Vibratory or oscillatory conveyors can be found in all types of industry, handling virtually any granular bulk material, often at elevated temperatures. These conveyors can be combined with other process functions, such as screening, cooling, drying and dewatering, while conveying. Although construction and installation is relatively simple, the engineering and design analysis of the vibratory mechanics is fairly complex. This paper will discuss the basic types of vibratory conveyors and the analysis of the material movement along the carrying trough.

Jan 1, 1985

By G. W. Johnston

INTRODUCTION For many years mining at the Stobie mine of the Inco Metals Co. consisted mainly of fill-type mining for higher grade ores and block caving or blasthole open stope mining for lower grade ores. Open stope mining, although quite favorable in the initial stoping phase, has always presented problems in the pillar recovery phase, especially at depth. In 1966, sublevel caving was introduced. This method is ideally suited for low-grade ore and can be applied very successfully to intermediate or higher grade ores providing proper controls are enforced. Sublevel caving has three distinct advantages: it is highly adaptable to mechanization; it recovers the ore in one operation; and it provides adequate ground sup¬port and safety regardless of mining depth. This method does, however, make extra demands, particularly for new types of supporting services. The constant presence of rock makes quality control of the grade of the ore being extracted essential. Increased de¬velopment, different types of ventilation, roadways, and maintenance are only a few of the many changes re¬quired. The care and maintenance of the fleets of diesel equipment and the modification of equipment is a con¬stant challenge. CHOICE OF SUBLEVEL CAVING The question arises, why mine by sublevel caving? Fig. 1 shows a typical problem encountered by the open stope or blasthole mining method. Near the surface there is little or no ground support problem. As mining progresses to an intermediate depth, however, ground failure starts to occur in the supporting pillars. If open mining is carried beyond this point, the critical depth is soon reached, accompanied by hanging wall caving, ex¬tensive pillar failure, and the danger of losing control of the mining cycle. The rock caved from the hanging wall mixes with and dilutes the ore being extracted from the blasthole stopes. Ore losses occur when pillar failure pre¬vents drilling and development of part of the ore. The interruption to the mining cycle causes serious curtail¬ment in production until ground failure is controlled and the mining method changed to adapt to the new conditions. Having recognized the limitations of open stope min¬ing, alternatives were sought. The first alternative (Fig. 2) was to fill the open stopes with sand fill be¬fore extensive pillar deterioration occurred, recover the pillar ore by fill mining, and then convert to total fill mining below. If the ore grade is high enough it can support the costly fill method. Recovery will be at a much slower rate and will therefore extend over a longer period of time. On the other hand, sublevel caving gives complete primary mining recovery in a short time and is very adaptable to mechanization, which is now a necessity to combat spiralling labor costs and give greater produc¬tivity per man. Sublevel caving is ideally suited as a mining method for low-grade ore bodies which eventually reach a criti¬cal depth for open stope mining. DEVELOPMENT The development phase comes first and of course its main purpose is to gain access to the ore and provide a route for ore removal from the mine. Initially a 20% inclined service ramp is driven in the footwall rock (Figs. 3, 4, and 5). It is preferable to start at the top of a mining block and drive the ramp down¬ grade so gravity can assist in mucking the blasted de¬velopment round, and also access can be gained more quickly to the initial production area. The ramp nor¬mally turns at 3.1 rad (180°) about every 152.4 m (500 ft) to keep it reasonably close to the rock disposal

Jan 1, 1982

By S. M. Carpenter

In an ever increasing ?carbon? society; management and growth will be measured by one?s carbon footprint (or output). Industries, especially mining, are under an ever increasing scrutiny of carbon, water and environmental mandates. These mandates are measured by the emissions caused by the combustion of fossil fuels. The fundamental building-block for any business, strategic or management decision must be based on an understanding of one?s ?footprint?. The scrutiny is most stringent for the commodities producers, power producers & fuel suppliers in the energy market. An overview of currently acceptable standards, application of those standards and nuances experienced in collecting the data necessary to analyze and complete a company?s carbon footprint will be presented. A lack of regulation, the fear and expectation of new and ever constraining rules, regulation and a change in the federal administration is a recipe for uncertainty in the marketplace.

Jan 1, 2010

By J. Helton, J. L. Bellanca, M. McNinch, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Accident data indicates that mobile haulage poses a significant pinning, crushing, and striking risk. Proximity detection systems (PDSs) have the potential to protect mineworkers from these risks. However, unintended consequences of mobile PDSs can undermine the safety benefit they provide. Soliciting iterative user input can improve the design process. Users help provide a critical understanding of how mobile PDSs may hinder normal operation and endanger mineworkers. Researchers explored users’ perspectives by conducting interviews with mineworkers from seven mines that have installed mobile PDSs on some of their haulage equipment. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance, and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure, and risk. Mineworkers also suggested that improved task compatibility, training, logistics, and PDS performance might help address some of these identified issues. This paper also gives additional insights into mobile PDS design and implementation. INTRODUCTION Pinning, crushing, and striking accidents are a large problem in underground coal mines, especially for mobile haulage. Between 1984 and 2014 there were 179 non-fatal and 42 fatal pinning, crushing, and striking accidents involving mobile haulage vehicles, including coal hauling machines and scoops [1]. Proximity detection systems (PDSs)—automated systems that decelerate and stop a vehicle in order to prevent a collision—have the potential to protect mineworkers in these situations. In fact, PDSs are now required on all place change continuous mining machines as of March 16, 2018, as a result of the final rule published in January 2015 (30 CFR 75.1732) [2]. To address mobile haulage, later in 2015 the Mine Safety and Health Administration (MSHA) also proposed a new rule that would require PDSs on mobile haulage vehicles [3]. Though there has been no additional actions related to the proposed rule and it is not currently required, mobile PDS can still help to save lives. MSHA estimates that the adoption of mobile PDSs could prevent approximately 70 injuries and 15 fatalities over the next 10 years [4]. As of June 2015, the underground coal industry had already equipped 155 of the 2,116 mobile haulage vehicles in use [1]. In order to capitalize on the projected safety gains afforded by PDSs, it is important that the systems are designed and implemented effectively. Along with others, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been exploring PDSs for more than two decades [5-7]. Throughout this time, NIOSH has also held several stakeholder meetings (2010, 2014, 2016, and 2017) in order to disseminate information and provide an opportunity to discuss on ongoing issues and concerns. Despite some progress, human factors remain a key concern. Previous research examined mineworkers’ attitudes towards PDSs on continuous mining machines [8] as well as how continuous miner operators’ perceptions of risk have changed as a result of PDSs [7]. However, stakeholders have still expressed a need to better understand how mobile PDSs affect the mining process, the mineworker, and whether and how they may present previously unidentified risks.

Jan 1, 2019

By C. Bailey Williams

Aragonite "sand," an oolitic lime-stone, is distributed throughout the Bahamas on the Grand Bahama Bank, adjacent to Southeast Florida. Bahamian deposits hold 75-100 billion tons of recoverable Aragonite. Aragonite's precipitation from seawater over 700 years ago assures low contaminates, making it a pure material for such industries as cement, glass, etc. A 90-acre, man-made production island was built south of Bimini, adjacent to ocean shipping channels mining is by cutterhead, suction dredge, dewatering, and stockpiling for further drainage and shipping. Aragonite is transferred to the U. S. East and Gulf Coasts via bulk carriers to points of sale.

Jan 1, 1978

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By M. Z. Mubarok, Z. T. Ichlas, A. T. Sugiarto, K. Sukamto

The use of ozone as an oxidant for the direct leaching of zinc sulfide (sphalerite) concentrate in sulfuric acid medium under atmospheric pressure was explored. The influence of acid concentration, feed gas injection rate, particle size distribution, stirring speed, temperature and slurry density on zinc extraction efficiency was examined. The experimental results showed that the leaching efficiency depends on all of these operating parameters except for stirring speed. It was found that essentially complete dissolution of zinc from the concentrate with the present method can be achieved in only about seven hours under the conditions of sulfuric acid concentration of 2 mol/L, particle size smaller than 74 µm, slurry density of 50 g/L, stirring speed of 420 rpm and feed gas injection rate of 1 L/min at ambient temperature. The experimental results suggest that the dissolution reactions produce independent elemental sulfur that is readily floated and can be easily separated rather than forming a layer on the surface of the reacted particle, as usually observed in a system with ferric-sulfate as oxidizing agent. It was therefore determined that the dissolved ozone play a key role in improving the rate of zinc dissolution from the concentrate. Analysis of the leaching kinetics indicate that the leaching rate follows the shrinking particle model, and the overall dissolution rate of zinc is controlled by a surface reaction.

By Preston McGrain

Geologic maps are indispensable tools in the modern search for mineral and fossil-fuel resources. They are the first essential step in understanding the lithologic nature and structure of rock units that form the land surface and that lie beneath it. They provide the basic foundation for planning mineral resource exploration programs and form the superstructure from which subsurface investigations are projected. In view of the economic application of such maps, the Commonwealth of Kentucky and the Federal Government entered a formal agreement in 1960 to map Kentucky geologically on a scale of 1:24, 000, or one inch map distance equals 2,000 feet on the ground. A 7. 5-minute quadrangle would comprise the unit map area. A resolution which urged the preparation of a new geological map of the entire State was passed by the Kentucky Society of Professional Engineers in February 1959, and was presented to the Governor of Kentucky, the Legislative Research Commission, Kentucky Department of Economic Development (now Department of Commerce), Kentucky Chamber of Commerce, and Kentucky Geological Survey with a request for support and action. The request was subsequently endorsed and actively supported by numerous civic and professional societies as well as representatives of various facets of Kentucky government, commerce, and industry. Monies to initiate the program were appropriated by the next session of Kentucky legislature; this appropriation was matched by federal funds (Hagan, 1961). Kentucky's state-wide topographic mapping project was completed in 1956, just four years prior to starting the geologic mapping program. The recently completed modern 7. 5-minute, 1:24,000 topographic maps made ideal bases for plotting areal geology. Had they not been available, it is doubtful if a geo- logic mapping program so large and comprehensive could have been undertaken.

Jan 1, 1966