Search Documents

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By T. Negeri

Flotation is the most efficient and preferred solid-solid separation method in mineral processing. However, enhanced production of high-grade concentrates at sufficiently high recovery still poses technological challenges to-day. A novel flotation method to produce final-grade concentrates from finely-ground ores in a single step is being developed and tested by CANMET. For the complex sulphide ores tested, grades are superior while recovery is considerably improved. Furthermore, concentrate production rates, at similar recoveries, are faster than for the conventional rougher-scavenger-cleaner configuration. This paper discusses the physical operating parameters affecting Cu-Zn flotation metallurgy.

Jan 1, 1995

By Arthur B. Johnson

Potassium, is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production. Potash is found throughout the world in both soluble and insoluble forms. It is only the soluble forms that are economically attractive to process, primarily chlorides and sulfates, with potassium chloride by far the most important potash salt. Sylvinite ore, a mechanical mixture of sylvite (KCl) and halite (NaCl), is a natural mineral of potassium. This ore is found in commercial quantities in the Permian sin region near Carlsbad, New Mexico. Vast tonnages of high-grade de, low-clay-content ores have been mined and concentrated during the past 40 years; however, these deposits are rapidly being depleted leaving high-clay, low-grade ore reserves of over 135 million tons. These ores, containing 13 to 22 percent K20 and 3 to 8 percent clay slimes; cannot be effectively processed by current commercial flotation methods. The present concentration processes for potash minerals in Carlsbad relate mainly to ores containing 1 percent or less of clay-slimes with a K20 content of 20 to 25 percent to yield products to meet the requirements of the agriculture market, namely, 95 percent KC1 equivalent to 60 percent K20. Discoveries of potash ore in Saskatchewan, Canada, have shifted the emphasis on expansion outside the United States. Presently, the American companies are looking to Canada for future growth, expenditures, and expansion. Four of the seven companies operating near Carlsbad are produces of Canadian potash despite the large investment sons required for shaft sinking and milling installations.

Jan 1, 1970

By J. C. C. C. Menezes, R. A. S. Silva, A. V. Colling, I. A. H. Scheneider

"Coagulants rich in ferric sulfate can be obtained from pyrite-containing coal tailings using a biohydrometallurgical process. The aim of this study is to evaluate the relationship between quantity of pyrite and rate of oxidation, with regard to the consequent production of ferric sulfate for potential use as a coagulant for water and wastewater treatment. Leaching experiments were carried out on the laboratory scale on four coal tailings with different concentrations of pyrite. Characterization of the coal tailings was conducted for the following parameters: total sulfur, pyritic sulfur, sulfate sulfur, organic sulfur, and elemental analysis of CHN (carbon, hydrogen, nitrogen). The samples were also subjected to X-ray diffraction analysis to assess their mineral compositions. The leaching experiments were accomplished using a laboratory column constructed as a packed bed reactor with a sprinkling system in a closed circuit. After four weeks of leaching, the liquor was filtered and evaporated to an iron concentration of about 12 percent w/w, which is typical of the ferric sulfate coagulants commercialized in Brazil. IntroductionCoagulants used for the treatment of water and wastewater are predominantly inorganic salts of ferric iron and aluminum. Aluminum salts, including aluminum sulfate and aluminum chloride, and prehydrolyzed metal-ion reagents, such as polyaluminum sulfate (PAS) and polyaluminum chloride (PAC), are the coagulants most widely used for water treatment (Bratby, 1980; Tchobanoglous et al., 2003; Buzin et al., 2014).However, the presence of residual amounts of aluminum in drinking water has been controversially implicated in neurological diseases (Association of California Water Agencies, 2000; Becaria et al., 2006; Campbell, Hamai and Bondy, 2001; Rondeau et al., 2000; Walton, 2006). A possible alternative is to use iron-based coagulants, such as ferric chloride, ferric sulfate or polyferric sulfate, instead of the aluminum salts (Jiang, Graham and Harward, 1996; Jiang and Graham, 1998). Iron-based coagulants are commonly produced by the acid dissolution of iron scraps or iron ore (Tchobanoglous et al., 2003).Recent studies have shown that it is possible to produce ferric sulfate coagulants from the pyrite present in coal tailings through a biohydrometallurgical process (Colling et al., 2011). The main advantage of this process is that it does not require acid addition, which can be favorable in terms of production costs. Acidophilic bacteria, such as Acidithiobacillus ferrooxidans, can increase the rate of pyrite oxidation and dissolution by several times (Kontopoulos, 1998; Brett and Jillian, 2003; Johnson and Hallberg 2003). They can be highly significant in the bioprocessing of coal tailings for the production of ferric coagulants, as their action favors the acidification of the medium and iron leach (Colling et al., 2011)"

Jan 1, 2016

By C. A. Carroll

In February of 1989 the Mission Complex of ASARCO Incorporated completed an expansion of its concentrator, raising the base mining rate from 25,900 TPO (28,500 STPD) to 37,200 TPO (41,000 STPD). The expansion was accomplished by extending the twelve existing Mission ball mills in length, by installing the grinding circuit from Asarco's idled Sacaton Concentrator along with various auxiliary equipment, and by modifications to the flotation circuit and water systems. This paper will give a brief history of the consolidation of the ore body which made the expansion possible and explain the various parts of the expansion.

Jan 1, 1990

By Leo R. Love

A comprehensive study of the environmental conditions of the area affected by the Colfax and Cheswick Power Stations is of extreme importance to Duquesne Light Company. The residents in the valley where the two plants are located have complained for many years about the emissions from the Colfax Plant which is of the 1920 to 1930 vintage and which has a capability of generating approxi¬mately 200 Mw. They were extremely happy to hear that the Company had plans for shutting it down, however, they were extremely unhappy to hear that we were planning to build another even larger one to take its place in the same vicinity, namely the Cheswick Plant with a capability of 570 Mw. They had visions of a plant twice the size of the Colfax Plant and belching out twice as much smoke. A few of the citizens from that area were most vehement at the public hearings that were held by the Allegheny County Air Pollution Bureau for obtaining an installation permit. With two power plants already existing in that area (Duquesne Light Company's Colfax Plant and West Penn Power's Springdale Plant), the primary concern of the Allegheny County Air Pollution Control Bureau was that the Cheswick Station might increase air pollution levels beyond what they considered to be dangerous limits. It became very evident that the Allegheny County Air Pollution Control Bureau would be extremely reluctant to grant installation and operating permits unless they were satisfied that the new plant would not increase local pollution levels and that we were taking sufficient steps to monitor the emissions from our plants and also the ambient air in the general area. We concluded that an extensive air pollution monitoring program must be conducted in the area to determine the effects of the operation of our plants. The program was conceived with our consultants, NUS Corporation of Rockville, Maryland, and was begun in June, 1968. It was designed to accomplish several things: 1. Determine the effect on the ambient air of the operation of each of

Jan 1, 1972

By J. L. Brinkman

"One of the most common emissions from detonating explosives are nitrogen oxides (NOx), which are potentially deadly if inhaled. Lab studies estimate emission quantities, though great variation is shown based on site-specific conditions, and lab tests may not fully represent field results. Field VALUES (have not been measured due to the vast area affected. OSMRE recently promised to release a ruling regarding surface mine NOx production. Once the ruling is implemented, it may eventually be necessary to monitor site-specific NOx production from blasting. A small unmanned aerial vehicle system (sUAS) is able to carry a NOx gas monitor, rapidly travel to the blast location, and to follow resulting clouds of dust and emission gasses. This project will perform laboratory tests to expand on current estimations, determine an optimal method for collecting data, and evaluate the ability for this unique application of sUAS to assist in health risk assessment for mine employees and nearby communities. Additionally, large initial NOx concentrations do not necessarily correlate to unsafe conditions, and this project will be ground breaking in observance of surface blasting emission dispersion. The project is still in early phases at the time of submission for this paper (Nov 1, 2017). Therefore, this paper focuses primarily on summarizing background research related to the project and a description of the project plan. INTRODUCTION Nitrogen oxide gases (NOx) are common emission by products of surface mine blasting. These gases can potentially cause risk to human health and safety, both for mine workers and communities near the blast site. However, these emission quantities are largely unmeasured and no attempts have been made to relate these VALUES (to human health risk. The primary objectives of this project are to determine actual quantities of emission gases produced during surface blasting, to evaluate immediate and long-term risks to nearby people, communities, and ecosystems, to develop a system for mine employees to easily monitor emission and risk levels, and then provide guidelines for mitigating health risks based on a location’s emission results. BACKGROUND Current research regarding health risk produced by surface mine blasting NOx emissions is extremely lacking. Estimations have been made based on laboratory research, though these same test results show wide ranges of possible gas quantities produced based on site-specific conditions. Even if these estimations are accurate, no method has been created to relate gas quantity produced to human exposure concentrations. To further understand this field, background research was studied pertaining to blasting emission gas formation, laboratory and field measurements, harmful effects of blasting emission gases, and relevant government regulations. Background on Blasting Emission Gases"

Jan 1, 2018

Australian underground coal mines predominately use the longwall method for coal extraction. In longwall mining at least two parallel roadways known as gateroads are mined to delineate the sides of the longwall block, a longwall installation face is then driven connecting the gateroads to enable the longwall mining equipment to be installed. Roadway development should ideally be ahead of the longwall so that the longwall equipment can be installed into the newly developed panel with minimal delay to coal production. A discrete event model of roadway development can help assess how a particular configuration may perform with high levels of variability and uncertainty in operations. One of the major delays associated with roadway development is caused by the shuttle car due to its cyclic stop-start nature. Shuttle car travelling paths and machine interactions are normally constraint by the mine?s roadway layout and mine safety issues. This paper presents simulations of shuttle car route options which can be considered at the design stage to minimize the cycle time of a shuttle car as part of a general roadway development simulation model developed using 3D Flexsim.

Feb 23, 2014

By M. S. Davis

The Tek Process can produce masonry products such as bricks, roof or wall tiles, and block from virtually any inorganic waste. In the process the aggregate raw materials, portland cement, water and common chemicals are first mixed together; then mechanically subjected to several thousand pound pressure per square inch. This causes a novel chemical reaction between the cement, chemicals and water; producing the "patented" Tek adhesive binder which holds the aggregate together in a stone-like mix. Simultaneously, the desired product shape is formed. The building modules can have strengths of 8000 p.s.i. (pounds per square inch) with completely sound aggregates utilizing air curing for a period of 28 days. With most aggregates, 3000 p.s.i. is achieved within 24 hours. Eventual strengths usually exceed 5000 p.s.i. with almost any raw material. Water absorption ranges from 5-7.5 percent. Both absorption and strength figures are superior to the most rigid of any and all A.S.T.M. specifications for the highest quality bricks. In most locations, the product (when brick shaped is called Tekbrik) can be produced significantly more economically than can comparable grades of clay or other bricks, be- cause almost any inorganic waste materials or pollutant can be used as a raw material. The process results in a lower manufacturing cost as compared to clay bricks; fuel cost to operate a clay kiln represents a substantial portion of the total cost. Capital expenditure for a Tek plant also is lower due to the large investment in clay kilns. Transportation savings also are important, clay brick factories must be very large because the kilns are uneconomical unless they are large. Most bricks are manufactured at the sites of clay deposits in relatively uninhabited areas. The cost of transportation to the job site represents a considerable percentage of the selling price.

Jan 1, 1974

By M. F. Goodrich

The concept of using water-only cyclones as a clean coal scalping device preceding a heavy media cyclone circuit shows considerable promise, as it can considerably reduce the feed to the heavy media cyclone circuit. The system will not perform as well as a heavy media cyclone circuit alone, but the resultant loss in yield is small and may be negligible under some conditions. The concept of water-only cyclone scalping has previously been suggested by others. By reducing the amount of raw coal to be processed in the more expensive circuits overall capital and operating costs may be reduced. There are a few commercial plants with circuits operating on this concept. In the Warwick and Rowland plants water-only cyclones are used to scalp the feed to a heavy media vessel and Deister tables respectively while Amherst Coal Company's McGregor plant uses them to scalp the feed to a heavy media cyclone circuit. The system was evaluated on a technical basis, both from a theoretical viewpoint and by analysis of a computer simulation, in order to gain a fuller understanding of its usefulness and limitations.

Jan 1, 1977

By Charles Stone, Eric Wang

A method for estimating geotechnical rock loads for shallow cut and cover subway stations is presented. Localized geotechnical conditions lead to extreme variations in rock loading on the walls of subway structures. Actual lateral rock stress on these structures can range from near zero to over four times the vertical in-situ rock stress. The primary factors affecting the actual lateral stress are intact and rock mass mechanical properties, excavation sequence, localized tectonic conditions, and potential future adjacent structures. The authors recommend using the AASHTO code value of 65 pounds per cubic foot (10 kN/m3) during concept design, followed by numerical analysis of rock wedges and stress measurement for final design.

Dec 1, 2022

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilize crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realize reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By George Mandarakas, Johan van Zyl, Karl-Heinz Becker

The world’s climate today has changed compared to 10 or 20 years ago. Many countries face water shortages; water sourcing for mining activities has become harder to secure. ESG’s focus on the industry has made us more aware of the need to preserve and responsibly use the water needed for wet processing in our milling and sorting activities. In a recent greenfield project in South Australia, 10 Gigalitres per annum would be required to process 5Mtpa of magnetite [1]. Published information indicates that the mining industry consumes approximately 12 EJ per year—or 3.5% of total global final energy consumption globally [2] or 3.33 trillion kilowatt hrs. This energy consumption is significant, considering the critical role mining plays in extracting and processing essential minerals for economic development and human progress. The perception of the mining industry is that not only does it consume significant power, but it also consumes a lot of the freshwater in the world. In fact, it consumes approximately 5% [3] of the total freshwater demand. According to the Intergovernmental Panel on Climate Change (IPCC), by 2050, 60% of the world’s population will be living in countries that are classed as water-stressed [3]. As more and more emphasis is placed on renewable energy sources, the amount of water used in mineral processing will increase because more and more raw materials require a water-intensive process. This increases the pressure on the mining industry to try and find water-saving initiatives. As part of this review, recent advancements in magnets have enabled magnetite processing facilities to achieve between 30 to 40% dry gangue material rejection before the wet beneficiation process (grinding and sorting). This reduction in energy consumption allows the reduction of energy consumption. Secondly, there is less material ground in the mills, which requires less water for mineral downstream processing.

Feb 1, 2025

By Walter E. Dean

Deep-sea manganese nodules are considered to be potential ores of manganese, nickel, cobalt, and copper. Considerable time, effort, and funds have been applied to the study of Se distribution of nodules on the sea floor and the location of economically important areas, but little effort has been spent in understanding the origin of nodules. Most theories that have been proposed to explain the origin of manganese nodules have been based on inorganic physicochemical processes. It is not by coincidence, however, that the area considered to be most economically feasible is in the zone of high biological productivity in the eastern equatorial Pacific Ocean and underlain by siliceous biogenic sediment. The genesis of manganese nodules and the concentration of many trace elements are intimately associated with biological processes.

Jan 1, 1982

By Robert J. M. Miller

Thank you Mr. Chairman. For more than 15 years a debate has been taking place among students of massive sulphide deposits as to the origin of these deposits. Prior that time it was widely accepted that the deposits were of hydrothermal, epigenetic and even replacement origin (Wilson, 14). Kinkel, Knight, Stanton and others advanced hypotheses which would explain the, formation of the deposits by different, largely syngenetic, volcanogeric processes. I was fortunate in having become involved in exploration for these deposits at about the time the debate was beginning and thus had an opportunity to apply with some success, some of the new and old ideas for formation of massive sulphide deposits. The deposits which I will discuss today are all located n northwestern Quebec, in the Abitibi orogenic belt. Mattagami Lake Mines is about 100 miles due south and Noranda's Horne Mine about 200 miles south of James Bay. In 1959 I prepared a talk which was presented to the 1960 CIM Convention calling attention to the spatial and possible genetic relationship between the ore sulphides of the Mattagami Area, Quebec and the tuffite, as well as the structures which controlled the ore. In this present paper I would like to cover the following points: (1) The general criteria used by the epigeneticists to support their contention that the deposits were formed after the enclosing rocks.

Jan 1, 1973

By A. I. Johnson

This paper describes," the application, of a modular or building block approach to the analysis, design, and control of complex mineral treating processes. The main purpose of the paper is tutorial, to show the reader how such processes can be modeled using a modern digital computer" and, not to discuss in any detail the results that may be achieved in such studies. It is proposed that, the main techniques be illustrated by reference mainly to the Bayer process for alumina extraction and purification; in cooperation with the Aluminum Company of Canada Ltd. the author and his Colleagues at McMaster University and their students have studied this, process as a means of applying new computer techniques to extractive metallurgical processes. The plant described was studied by the author and his colleagues as a senior undergraduate project in cooperation with the Aluminum Company of Canada. It is one of several studies that have been carried out with Canadian industry. (1)

Jan 1, 1972

By V. C. Koppe, J. F. C. L. Costa, D. M. Marques, A. Amaral

Errors associated with estimating the grade of an attribute of interest in a deposit can compromise planning, sequencing, and mineral beneficiation decisions. Several factors are associated with estimation errors. Among them, we can highlight the factors associated with sample spacing, the size of production volumes, and the variability of the attribute considered in the estimation. The access to estimation error can be obtained by some geostatistical methods, for example, by stochastic simulation. However, this is a process that in some situations is computer intensive and takes time. Previous works have proposed a simplified method to access the Maximum Estimation Error (MEE) associated with different types of grade variables, depending on the sample spacing, at small production volumes and considering specific coefficients of variation ranges. This paper presents an approach to assess the MEE associated with long-term volumes. Considering the methodology proposed, it is possible to approximate if a specific drilling pattern used in a deposit provides an acceptable pre-determined estimation error for Resource Classification. Results and considerations on the impact of the geometry of larger production volumes on the MEE calculation are also presented.

Jun 25, 2023

By Roberto Pimentel de Souza

CURD started producing pellets in 1969, with one two-million ton straight grate plant. In the beginning of April '73, the second unit came on stream with an additional capacity of 3 million TPY of pellets. In January '77, the third unit started, bringing the annual capacity to 8 million TPY. For the present year 3 more units, 3 million each, are expected to begin production. CVRD's experience is given about the use of different binders and additives. Over the years several kinds of pellets have been produced to satisfy the market requirements. General quality information is given regarding each.

Jan 1, 1978

By W. A. McKinney

The U.S. Bureau of Mines, Kennecott Copper Corp., and New Mexico Institute of Mining and Technology are cooperating on a research project to improve extraction of copper from previously leached waste dumps that are in part compacted and impervious to leach solutions. The field work is being done at the "J" leach dump, Chino Mines Division, Kennecott Copper Corp., Santa Rita, N. Mex. The laboratory percolation leaching tests were made at the U.S. Bureau of Mines Salt Lake City Metallurgy Research Center on drill core samples from the "J" dump to determine how much copper might be leached if permeability could be restored by explosive heaving or other means. The core samples from nine drill holes on "J" dump contained from 0.06 to 0.14 percent copper. Copper extractions ranging from 15 to 3 percent were obtained in 75 days by percolation leaching of minus-1-inch material with dilute sulfuric acid. The tests results indicate that about 2'7 percent of the copper remaining in the "J" dump could be extracted under ideal leaching conditions.

Jan 1, 1970