Search Documents

By S. S. Pathak, S. Mishra, M. H. Tyeb, A. K. Majumder

Roping in hydrocyclones is a well-known phenomenon in mining and mineral industries which put serious restrictions on their continuous and maintenance free operation. Roping is mostly observed in association with high underflow solid concentrations which can be attributed to higher fraction of solids reporting to the underflow or the feed solid concentration itself being higher. This paper proposes a newly designed spigot with a truncated conical geometry which can allow for a rope-free discharge at higher feed solid concentrations. The experimental observations revealed that in the operation of a 50.8-mm-diameter hydrocyclone, roping ensued at 10% to 12.5% (wt%) feed solid concentration depending on feed inlet pressure for the cylindrical spigot, whereas with the modified spigot, rope free discharge was attained even at 25% (wt%) feed solid concentration.

Jan 8, 2022

By R. S. Olson

The operation of a series wash thickener-two stage filtration circuit determines the soluble loss in many hydrometallurgical operations A study of this circuit yielded expressions which permit calculation of soluble loss for almost any condition of operation. The soluble loss over a range of the circuit variables is presented to illustrate and evaluate circuit performance, The interrelation of factors affecting filter performance and some of the wash circuit, variables are quantatively described. Filter wash, which is governed by wash zone size, filter pulp level and filter feed pulp density, has the greatest affect on soluble loss. Excepting clothing blinding and flocculation the factors which decrease filter capacity also decrease soluble loss. Repulping with water, under some circumstances, can bean important means of soluble loss reduction. Water for primary filter wash, leach pulp density repulp density and wash thickener underflow density have little effect on soluble loss. The dilution of both o the filter pulps with wash solutions is suggested as a means of reducing soluble loss, and at the same, time, controlling the performance of the filters. Blowback and filter cloth blinding seriously increase soluble loss.

Jan 1, 1962

By Ranajit Kumar Sahoo, Shatrughan Soren, Surendra Kumar Biswal, Soumya Sahoo, Sachida Nanda Sahu

The presence of appreciable quantity of clay mineral in Indian hematite ore needs an attrition technique using screw scrubber in the beneficiation circuit to remove the ultrafine clays and avoid downstream operational problems. Spectroscopic analysis revealed that iron ore samples obtained from the Barbil region of Odisha contain a high amount of silica and alumina in the form of clay minerals (e.g., kaolinite) contributed as a loss on ignition (LOI) in the iron-making process. Iron ore fines of below 10 mm size were subjected to a laboratory-scale screw scrubber, and the effectiveness of scrubbing as well as the pelletization of the scrubbed product was investigated. The screw scrubber in the beneficiation circuit helps to remove the clay minerals, causes an increase in iron values from 63.65% Fe(T) to 66.18%Fe(T), with improved physical (CCS of 325 kg/pellet) and metallurgical (RDI of 2.24%) pellet properties.

Aug 31, 2020

By John W. Sweeney

Florida is usually thought of as a vacation State, not a mining State, yet Florida has been the leading producer of phosphate rock in the United States for 85 consecutive years and in 1978 supplied over 80 percent of the national output and over 30 percent of the world's output. It is estimated that the Central and South Florida phosphates contain 412,800 short tons (374,000 metric tons) of U308, that 115,000 short tons (104,000 metric tons) of U308 will be contained in the wet-process phosphoric" acid procsssed in the United States through the year 2000, and that 54,000 short tons (49,000 metric tons) of U308 will be available from Florida. In 1978, two companies in Florida and one in Louisiana went on-stream recovering uranium oxide from wet-process phosphoric acid and three others started construction of U308 extraction facilities. These six companies will have the capacity to recover 2,137 short tons (1,900 metric tons) of U308 annually in 1980, which will account for about 15 percent of our domestic requirements.

Jan 1, 1979

By Wei Luo

Nickeliferous laterites were characterized by particle size analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDX), Fourier transform infrared (FTIR) spectroscopy and thermal analysis. Results showed that the laterites consist mainly of nickel-substituted lizardite with cobble-like morphology and traces amounts of magnetite and phlogopite. As fluoride ions can react with silicon in the lizardite crystal structure and form metal-fluoride complexes, as well as increase the equilibrium constant of the lizardite dissolution in acid solution dramatically, the addition of minor fluoride salts (0.2wt.% NaF) gave a markedly enhanced metal extraction rate (Ni 81.7% and Co 52.3%) under the experi-mental conditions of particle size d50= 25 µm, 10% (v/v) H2SO4, reaction time 2 h, reaction temperature 90°C, liquid-to-solid ratio 3 mL g-1 and stirring at 500 rpm compared with H2SO4 alone (Ni 69.6% and Co 30.8%).

Jan 1, 2010

By David L. Kuck

Siderophyle platinum-group metals and sane gold are a thousand times more abundant in metal and chondritic meteorites than in terrestrial or lunar rocks. Type I and II carbonaceous chondrites contain granules of the high boiling point metals W, Re, Mo, Ir and Os. Metal meteorites and the metal fractions of other chondrites contain siderophyle Pt, Pd, Ru, Rh, Os, Ir and Au. Spectra of sunlight reflected from asteroids, when compared with those of meteorites and specific minerals, provide a rough classification and guide to sources of precious platin-group metals.

Jan 1, 1982

By A. E. Sears

The intent of geomorphic landform design is to mimic the function of the natural landscape. In a surface mine reclamation application, geomorphic landform design has the potential to mitigate stream loss. This research quantified features of reference landforms and performed computer modeling of a conceptual valley-fill design using geomorphic landform principles. A design was created using published design parameters with a software design tool (Carlson Natural Regrade with GeoFluv). Three additional designs, incorporating field-obtained regional geomorphic landform parameters, were completed and resulted in a geomorphic landform design specific to southern West Virginia. This work illustrates the importance of field determination of the ridge to head-of-channel input and drainage density parameters. Values of ridge to head-of-channel distance measured in this study were consistently an order of magnitude greater than software recommended values (SRV); SRV = 24 m (80 ft) versus field= 220 m (720 ft). Similarly, for the drainage density parameter, the software recommended range is 6 to 9 km-1 (80-120 ft/ac). The field measurements for central Appalachia quantified the drainage density to range from 5 to 5.3 km-1 (67-70 ft/ac). This affects Appalachian valley-fill stream construction by making the stream lengths shorter and the land slopes steeper with straighter headwater channels compared with areas in the southwestern United States. While the application of geomorphic landform design to surface mine sites presents challenges, this work provides support for future applications.

By R. E. Lindstrom

The mineral bastnasite is utilized to describe alternate processes for the extraction and separation of the rare-earth elements by solvent extraction. The rare earths can be acid-leached directly or fused with NaOH before acid leaching. Cerium, the major constituent, can be recovered by fractional precipitation, fractional leaching, or solvent extraction with tri-nbutyl phosphate. The latter process is capable of producing 99.5-percent pure CeO2 at 98+ percent recovery. Lanthanum is subsequently recovered by fractional precipitation or solvent extraction with a nitrogen-based extractant. A 20-stage mixer-settler operation with a primary amine extractant results in a 95-percent pure La203 fraction at 96 percent recovery. Europium is amenable to extraction from most of the remaining rare earths with an organophosphate extractant. Selective stripping of the europium, followed by reductive precipitation, produces high-purity Eu203. Another possibility for europium purification involves the differential extraction of europium with an amine followed by a sub- sequent reducing strip. Separation of the remaining elements is more difficult but can be accomplished with amine or quaternary ammonium extracts. Typical separation factors achieved are 3. 8 for praseodymium-neodymium and 10. 5 for neodymium-samarium.

Jan 1, 1967

By E. Yigit

Hydrometallurgical production of zinc from concentrates is generally carried out by H2SO4 leaching. For the smooth operation of this process, some harmful components must be removed from the leach solution before the electrolysis stage; MgO is one of these compounds. Zinc concentrate samples from the Mount Isa mines were used in leaching tests. Leaching tests with an aqueous solution of H2SO4 and SO2 gas were carried out at various temperatures, pH levels and leaching durations. While duration and the pH value of the solution were effective parameters in H2SO4 leaching, temperature and pH were more effective in SO2 leaching for the removal of MgCO3 and CaCO3. Removal of MgCO3 and CaCO3 was generally achieved at low pH values. The results show that SO2 gas can be a good alternative to sulfuric acid in the leaching of MgCO3 and CaCO3

Jan 1, 2010

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Jan D. Miller, Chen‑Luh Lin

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of cm size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of mm size. Based on Micro-XCT, it was expected that 85% of the copper for sample A could be recovered at 65% of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual energy (DE) X-ray radiography was used as a basis for sorting. Previous DE X-ray radiography of a drill core sample demonstrated that this rapid detection method can be used to identify rich or poor Cu-bearing coarse particles. Pilot scale X-ray sorting of sample A (10 × 1 cm) showed 31% rejection of a 0.08% Cu gangue product with a corresponding recovery of 90% copper.

Nov 30, 2021

By Alireza Ayoubian, Richard Finno

The network of freight tunnels in Chicago consists of about 62 miles of horseshoeshaped tunnels constructed typically less than 50 feet below ground surface. These tunnels serve as repositories of much infrastructure and should remain serviceable. The tunnels are often impacted by adjacent excavations and the question arises as to the existing state of stress in the final liner. This paper discusses construction of these tunnels and presents the results of finite element analyses which were used to obtain ranges for axial forces and bending moments that have developed in the final liner of the freight tunnels since their construction.

Jun 13, 2023

By Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides: chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 1000 to 150°C. The rate of dissolution of chalcopyrite becomes so rapid under these conditions that the rate of recovery is no longer limited by the rate of chalcopyrite dissolution, but by the degree of exposure and other factors. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, size of sulfide particles, and fraction of sulfide exposed to solution.

Jan 1, 1972

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Laramide porphyry copper deposits are large, low grade (<0.8% Cu) deposits that contain disseminated copper minerals, breccias, and stockwork veinlets of copper and molybdenum sulfides associated with porphyritic intrusions in Southwestern New Mexico. Critical minerals, such as PGEs, tellurium, indium, germanium, and gallium are recovered from the anode slimes remaining after copper is refined. Detailed age dating, mineralogy, geochemistry, along with geologic mapping could refine the location of critical minerals within specific systems and could identify porphyry systems with elevated critical minerals that could become economic, in addition to the already produced copper, gold and molybdenum.

Feb 1, 2023

By J. Jorge, J. Mariño-Salguero, B. Álvarez-Rodriguez, J. M. Menéndez-Aguado, J. J. de Felipe

"This work focuses on the characterization of heat generation during dry fracture by direct impact of a tantalum ore. Moreover, an attempt was made to quantify the heat energy loss to the environment during the grinding process of a ball mill. The study was carried out using mineral samples from a Spanish mine that were characterized by measuring their density and specific heat. During the experiments, increases of temperature ranging from 5.9 to 7.3 °C after the fracturing process were observed. A numerical model was then applied to calculate temperature distributions through the mill wall. Three possible combinations of heat transfer coefficients were analyzed, from (1) Kapakyulu and Moys, (2) Duda and (3) the heat transfer laboratory of Universitat Politècnica de Catalunya. The models with the coefficients from Kapakyulu and Moys and the heat transfer laboratory of Universitat Politècnica de Catalunya were found to provide results that were in best agreement with the experimental data. IntroductionEvery year, several billion tons of metallic ores, minerals, cement and other solids used in the ceramic and chemical industries are subjected to size reduction in ball mills around the world. The U.S. Department of Energy (2005) reported that in the United States about 29 percent of the total energy used by the mining industry, or 0.4 percent of total U.S. energy consumption, is used in comminution. In Canada and Australia, comminution is responsible for about 2 percent and 1.5 percent of total energy use, respectively. In nonindustrialized countries where mining constitutes higher fractions of their industrial sectors, comminution costs represent a significant contribution to mine operating costs. The specific energy consumption values for the grinding of these materials typically range from 5 to 50 kWh/t. Thus, a significant amount of electrical energy is consumed in the ball mill grinding operation (Aguado et al., 2006; Gupta and Sharma, 2014). Grinding can represent up to 50 percent of the direct operating cost in a mineral processing plant, especially as comminution devices operate in highly inefficient ranges of 4 to 8 percent (Wang, Yang and Yu, 2012)."

Jan 1, 2017

By John Dodd

Advances in the technology of abrasion resistant irons and steels, which could help in combating abrasion and wear in mining operations, are reviewed. Nodular irons alloyed with nickel or copper and molybdenum, with acicular, bainitic or bainitic-martensicic microstructures are described. These alloy irons combine excellent castability and relatively easy machinabilitv with good resistance to wear. Recent progress in the development of high chromium molybdenum alloy irons is outlined, by which high temperature heat treatment of massive castings can be eliminated, alloy costs can be reduced and cracking problems avoided. Data is also given on the erosion-corrosion resistance of these irons. Trends in the development of improved cast steels are outlined. Factors influencing the toughness and abrasion resistance of manganese steels are considered. The 6% Mn 1% Mo manganese steels are shown to have a useful combination of toughness and abrasion resistance. Composite castings are seen as a means of com- bating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1981

By K. S. Radcliffe

Results are presented for the first phase of an experimental program to study the feasibility of using acoustic velocity for predicting the state of stress in a rock mass. Compressional wave velocities were determined axially in cylindrical samples during uniaxial compression for several rock types conditioned in dry and water-saturated environments. Results indicate that in rocks containing compressible voids or cracks, substantial velocity change occurs with the application of stress in the lower (below 100 MPa) stress regime. The effect norm- ally is nonlinear, however, and diminishes to asymptotic values when cracks or voids become closed or with saturation. Empirical prediction equations were derived for each rock type by linear and nonlinear regression analyses, and correlation coefficients were calculated to determine the equations that best fit the stress- velocity data. The operational range for predicting stress using compressional-wave velocity appears to be within the range of vertical stress expected in most shallow to intermediate depth mining operations (less than 1,000 m). Based on the experimental results to date and theoretical considerations, it appears that the technology can be advanced to predict in situ stress based on acoustic P-wave velocity determinations in most mining situations.

Jan 1, 1986

By Neil H. Bostick

This research, sponsored at Stanford Research Institute by the Grand Junction Operations Office of the U.S, Atomic Energy Commission, was an outgrowth of the concern that presently-known ore reserves may be inadequate to meet the projected demands of nuclear power reactors. The original program at SRI was to design a comprehensive geological information system and use it to store and analyze the very great quantity of data needed to estimate uranium ore reserves. Study of the problem showed that it could be solved only by use of modern electronic data processing techniques, so such a comprehensive system was designed and tested. The system test was satisfactory, but input lead time and total expense were shown to be too great for the system to be practicable for the AEC under present circumstances. Thus, based on results of the earlier research, a specialized and simplified procedure for predicting approximate uranium ore reserves was devised. The prediction is based on general geology of specific area cells of the earth, in order to provide complete volume coverage; the strata in these ores are evaluated for uranium ore favorability on the basis of a few selected criteria in order to allow rapid data input. Since the bulk of U.S. reserves are in clastic host rocks only such strata are considered in this work. This paper describes the structure and some details of the resource system and how it was tested in rn area of the western United States.

Jan 1, 1969

By James E. Lawver

Part I describes the general geology of the Florida deposits. As the lucrative Bone Valley Formation is depleted, replacement production will move progressively into areas of total Hawthorn production. The reserves of the immediate future are a mixture of two distinct ore types referred to as the upper (high grade) zone and the lower (low grade) zone. The upper zone is somewhat similar to the Bone Valley Formation that has been Florida&apos;s source of production for the past 100 years and will respond favorably to present beneficiation practices. By contrast, the lower zone ore contains significant quantities of dolomite that must be removed in order to produce an acceptable grade pebble or flotation sized product. Part II reviews past practice and describes future trends in mining and ore transportation. This presentation (Part III) is confined to the problems of beneficiation, waste disposal, and environmental regulation.

Jan 1, 1983

By Erik Klohn

The El Soldado copper deposit occurs in volcanic rocks of alkaline affinity of Lower Cretaceous age. The orebodies are discordant and show strong structural and lithological control. The mineralizing event was accompanied by hydro- thermal alteration expressed as carbonatization, silicification, and chloritization. Individual orebodies contain bornite-chalcopyrite cores which are surrounded by haloes dominated by chalcopyrite and pyrite respectively. The sulfur isotope composition of copper sulfides strongly suggests the sulfur is of magmatic origin. Fluid inclusion studies show the mineralizing fluid to be a highly saline NaC1-CaC12, brine. No evidence of boiling was found. The deposit is most likely of epigenetic origin. Hydrothermal fluids were produced during crystallization of a sodium rich trachytic magma during the waning stages of an episode of alkaline magmatic activity. Similar copper deposits along the Chilean Coastal Range may also be associated with alkaline host rocks.

Jan 1, 1986

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

During the past 15 years, roof fall rates have fallen dramatically in US coal mines, particularly in regions where the roof is weakest. The remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present a design methodology that builds on and quantifies the basic roof support concepts that have been successful in the USA. The methodology starts by defining three modes of roof support, based on the roof strength relative to the stress level: (1) suspension, where roof bolts mainly provide skin control for strong roof; (2) beam building, where moderate strength roof can be supported by roof bolts alone; and (3) supplemental support for weak roof. Next, a large database of roof fall histories at a number of mines is used to define the approximate boundaries of these three regimes based on the coal mine roof rating and the depth of cover. Finally, guidelines are presented for site-specific design of support systems within each regime. The new computer package, analysis of mine roof support (AMRS), implements the design methodology.

Sep 29, 2020