Search Documents

By III Feeley

Coal is the nation's most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

By Steven J. Schatzel, James Addis, K. Vaibhav Raj, Berk Tulu

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to enhance methane control and mine ventilation practices at coal mines, as a method to mitigate hazardous work conditions. NIOSH researchers conducted case studies to investigate the effectiveness of existing systems and improve performance to decrease the potential for unplanned or excessive methane emissions. At one mine, drainage was influenced by hydrofracking inefficiencies where two of the six wells showed good frack development. Methane content was variable, from 300 ft3/t to 600 ft3/t. This paper also summarizes overburden movement during undermining and the estimated quantities of gas transported to the mine using FLAC3D and CFD modeling. The findings from this research effort highlight considerations based on specific mine conditions that may also be applicable to most longwall mines utilizing methane control systems.

Feb 1, 2025

By Muhammad Azeem Raza, Samuel Frimpong

Underground mining environments are inherently hazardous and can lead to emergencies where effective rescue and self-escape become critical. Missouri University of Science and Technology is pioneering new technologies for effective self-escape. The rescuers and miners need to be trained in these new technologically driven environments. Previous research in fields like aviation, medical surgery, and oil and gas drilling has demonstrated the effectiveness of virtual simulation training, but the mining sector has yet to fully adopt advanced tools such as eye-tracking and immersive training modules. This research proposes a comprehensive training infrastructure incorporating these technologies to enhance situational awareness and decision-making during emergencies. The novelty lies in the application of advanced miner escape and communication technologies, specifically designed to monitor and enhance cognitive responses in high-stress situations. By leveraging these technologies, the proposed training infrastructure aims to prepare the next generation of underground miners and operators, by equipping them with the necessary skills to manage emergencies effectively.

Feb 1, 2025

By Frank Ruskey

Many problem associated with potential hazards in a proposed mining area may not be adequately appraised because of the complexity of trying to evaluate them in terms of production requirements. Frequently, encountered hazards have to be dealt with by day-to-day operational schemes that require the miner to either force a way through them or avoid them by blocking off the area in which the hazards are known to exist. These considerations, after the mine is in full production, can be costly to the mine operator and can increase the danger to the miners. A hazard-evasion computer program for mine planning that will appraise proposed mine layouts on the basis of existing or potential hazards has therefore been developed. The program is intended for use during the planning phase of a mine, where it should assist the mining engineer in making decisions in mine design. With the output from this program, the mining engineer should be able either to corroborate his judgments made on the basis of mining experience or to find unanticipated solutions to design problem. The program tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on a criteria of minimum-abandoned-coal) limits the number of choices that need to be considered and appraised for applicability to a given mine scheme.

Jan 1, 1973

By A. T. Stroebel

Diatomite deposits, the skeletal remains of tiny aquatic plants called diatoms, are found in many parts of the world. Only a few of these de- posits are of commercial value. Open pit mining is used in nearly all deposits now being worked. Processing methods range from simple drying, crushing, sizing and packaging to carefully controlled and highly sophisticated calcining and air classification procedures, employing the latest control and testing techniques. The major uses of processed diatomite are in filtration as filter aids and fillers and extenders.

Jan 1, 1979

By W. E. Bardelmeier

The high speed conveyor type self unloading bulk carrier concept has been around for about 70 years. Although the design was developed, refined and steadily improved in the Great Lakes, to date limited numbers of such vessels have emerged in the bulk ocean trades, and these have tended to concentrate within specific mineral trades. For example, North American gypsum companies have embraced conveyor self unloaders to the point where such vessels almost exclusively carry the gypsum requirements of this part of the world. One major aluminum company has developed an impressive fleet capability in self unloaders. Application of other ships tends to be fragmented through several mineral trades. A few years ago a new phenomonen began to appear on the Great Lakes. Whereas it had historically been accepted in that region that self unloaders were effective vessels for the minor bulk trades including limestone, coal, salt, gravel and sand; they had seldom been employed heavily in the big volume iron ore trades. Suddenly, however, the new generation of 60,000 ton Lakers which emerged were all designed as high speed self unloaders. The new vessels intended to trade especially in ore, or alternatively especially in coal, have somewhat different internal features, but the important point is that all are self unloaders.

Jan 1, 1979

By John M. Hill

Automation technology has many facets, some well tested and proven, some yet to be put to the acid test of economic reality. In this paper, we will limit our purview to the former. Consider, if you will, an automated handling system combining high-speed conveyors and automatic devices on-line which not only provide signals for routing and sorting, but also format those signals for the production of manufacturing, inventory, shipping and billing paperwork. This is not futuristic, but practical and a realistic accomplishment. Therefore, the following discussions will address today's challenges not with tomorrow's solutions, but rather, with an established technology which is playing an increasingly prominent role in materials handling systems. Until recently, relatively modest importance has been attached to the timeliness of information feedback from the production or assembly line, warehouse or distribution center. Thus, initial applications of automatic identification equipment focused almost exclusively upon the control of materials flow - that is, routing, sorting, etc. However, these systems have performed successfully and quietly established an enviable track record as reliable materials control tools.

Jan 1, 1973

By Martin B. Treuhaft

Expectations for coal in the early to mid-1970's prompted the government and industry to pursue research and development programs to increase underground and surface mining coal productivity and net coal recovery. Several programs concerned advanced surface mining methods for thin seam coal recovery. Three such programs, along with related areas of interest, are presented in this paper, namely: (1) extended depth augering for trench-strip applications; (2) high recovery auger heads for enhanced recovery; and (3) variable wall mining in low cover longwalls. Conceptual development is examined, prototype testing is discussed, and potential operations are considered.

Jan 1, 1983

By E. Maré

Some of the members will probably ask themselves what close relationship exists between hydro-metallurgy and a wet scrubber, but we are sure that as soon as deeper thought is given to the matter it will be realised how vital scrubbing, operations are in metallurgical plants. In ordinary metallurgical installations or pyro-metallurgical processes ore concentrates are first of all shifted from place to place and dust is created. In other cases the ores or concentrates are crushed or dried or roasted, and in each one of these operations dust and fumes, are created. All suspended particles and fumes originating from the abovementioned conditions not only, in many instances, provide health hazards which disrupt production and endanger the personnel in the plant, but also are the source of economic losses through extra maintenance and wear to moving machinery due to abrasion and corrosion. Further losses are incurred by the waste of fine, very often valuable, components. The Party who once said that in several metallurgical plants the bulk of the profits was discharged into the atmosphere by the stack wasn't stretching the truth. There is a place in Africa where a gold producing concern used to lose over 5 oz. of fine gold per day out of a total production of 3000 oz. per month. In another instance, copper concentrate going as high as 80% Cu was discharged into the atmosphere at the rate of 4 tons per day. Realising the value of removing and collecting solids and fumes created in metallurgical plants, a thorough study was made of the available plant and equipment offered on the market. Some units were found very efficient, but very expensive; some others also very efficient but with temperature and maintenance limitations. Some others were also efficient but prohibitive from the point of running costs.

Jan 1, 1963

By T. W. Martin

The use of conveyors in large, open pit mines and their drawbacks are discussed. Technological developments such as long distance conveyors capable of handling large rocks are explored. The development and testing by the Bureau of Mines of a prototype crib and cable conveyor for handling large rocks are discussed, and possible modifications of the concept for a production model are examined.

Jan 1, 1984

By Richard L. Bullock

Believe it or not, mine evaluation and feasibility studies are as old as the industry itself. In the first recorded writing on mining by Agricola (1556), he gave several clues as what to look for in evaluating a mine, to determine if it was economically feasible. Below is the guidance from Agricola, with my interpretation of what he would include today. Now a miner, before he begins to mine the orebodies must consider seven things, namely: ? The situation (the geography/topography). ? The conditions (the geologic/mineralogic and mining conditions). ? The water (availability, hydrology and ownership). ? The roads (plus the railroads, power lines, all other infrastructure). ? The climate (the weather-rainfall/environment). ? The right of ownership (the land and legal entitlement). ? The neighbors (the social environmental concerns of the area). It is amazing how much of his guidance has not changed in 455 years. Yet Agricola gives no guidance on determining the correct cost, or determining the correct commodity pricing. But he does give a few words of caution on the related ethics involved on buying mineral properties: ?A prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him.? Three hundred years later (1866), to further amplify this point, in the most famous thing that Mark Twain never said, as an introduction to a lecturer to an audience of gold-miners at Red Dog, CA, the famed author/humorist allegedly described a mine as ?a hole in the ground owned by a liar? (Farrar & Rinehart, 1935). So, one might conclude that between these two dates, the mining industry did little to improve its reputation. Unfortunately, since Mark Twain allegedly made those remarks, we have not done near enough to gain accountability for the mineral industry.

Jan 1, 2011

By Yuemin Zhao, Wenxuan Liu, Maoming Fan, Zhanyuan Long

"Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium and phosphorus. These coalassociated elements are significantly enriched in coal combustion byproduct fly ash because the majority of the main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main element oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides and unburned carbon.Chinese coal fly ash usually contains about 5 to 15 percent of unburned carbon, which are generally chars with irregular shapes and wide particle size distribution. In addition to unburned carbon, XRD analysis of four Chinese fly ash samples from Liaoning, Shanxi, Guizhou and Shandong provinces indicates that the fly ash samples are composed of minerals such as quartz (SiO2), mullite (3Al2O3.2SiO2 or 2Al2O3.SiO2), hematite (Fe2O3), maghemite (gamma form of hematite, ?-Fe2O3) and magnetite (Fe3O4). The mullite and quartz particles are usually present as spherical particles because they are formed by melting clays, feldspars, quartz, calcite and other common minerals in coal during coal combustion. The silicate particles have usually entrapped gas to yield hollow spherical particles because their lower melting point facilitates gas entrapment.The iron oxides are usually spherical also. The magnetite (Fe3O4) is derived from pyrite (FeS2), hematite (Fe2O3), siderite (FeCO3) and limonite (2Fe2O3.3H2O) in the coal. Maghemite (?-Fe2O3) is formed by dehydration of the mineral hydrohematite (?-FeO(OH)) and/or oxidation of magnetite (Fe3O4) during coal combustion. Maghemite (?-Fe2O3) and magnetite (Fe3O4) are strongly magnetic, so they are recovered from Chinese coal fly ash and widely used for coal processing in China (Fan et al., 2005, 2000)."

Jan 3, 2018

By J. S. McEwan

This paper describes the derivation of a set of simultaneous algebraic equations that can be solved to produce a rigorous theoretical mass balance around solution mining wells. This mass balance can then be compared with a mass balance calculated from field measurements to provide the percentage of mass balance closure. Significant deviations from the closure can be an indication that the wells are either gaining or losing circulation fluids. The equations also provide calculations for the amount of water and dissolved mineral that accumulates in the well during the mining process, as well as the net mining rate. Equations for both single mineral mining and multiple mineral mining are discussed. They can easily be formatted into spread sheets for rapid calculation of field measurement data.

Jan 1, 2010

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic meters per hour) for dozers operating in hard-rock bulk push applications. The particle size distribution of the material employed in the test rig was modeled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard-rock dozer push operations. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 to 40 m.

The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure of roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations and trial-and-error testing. Both the prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh, PA before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

By M. Sadegh Safarzadeh, Erich U. Petersen, Jan D. Miller

"An acid bake-leach process has been identified and applied to an enargite concentrate containing ~67% enargite, ~27% pyrite (FeS2), ~3% chalcopyrite (CuFeS2), ~6% sphalerite (ZnS) and <1% galena (PbS). Sulfuric acid baking of this concentrate resulted in the transformation of the concentrate to S8, As2O3, HFe(SO4)2•4H2O, PbSO4 and Cu0.47Fe0.53SO4•H2O, all of which (except elemental sulfur and PbSO4) dissolved during the water leaching step. More than 87% Cu and 64% As were leached when the concentrate was baked at 200°C over 7 hours with a sulfuric acid-toconcentrate weight ratio of 1.6. Less than 1% As was lost to the gas phase. Upon water leaching, copper and arsenic were released to the solution at a concentration ratio of about 3:1. While enargite is very reactive during the sulfuric acid baking reaction, other minerals present in the concentrate such as pyrite, galena and sphalerite may compete to consume sulfuric acid and be converted into their corresponding sulfates at different concentrations. The purpose of this paper is to present our examination of the effects of sulfuric acid dosage on the extractions of Cu, Fe, and As from an enargite concentrate. In this regard, the concentrate, baked concentrate, and the leach residues are characterized and a conceptual process flowsheet is described for the acid bake-leach process for the treatment of enargite concentrates.IntroductionThe occurrence of enargite (Cu3AsS4) in copper ores and concentrates and the associated high arsenic values in such resources have resulted in a considerable decrease in the demand for such concentrates because they cannot be economically processed using conventional technologies such as smelting and atmospheric leaching (Mihajlovic et al., 2011). The exploitation of such problematic deposits through competitive treatment strategies will be required in the near future in order to satisfy increasing pressure from the copper market. It is expected that the average arsenic grade of copper concentrates will increase from 0.17% in 2008 to 0.22% by 2020 (Mayhew et al., 2011).The acid bake-leach process was identified and selected for further investigation at the University of Utah as a possible process alternative for the treatment of enargite concentrates. In this case, adequate amounts of concentrated sulfuric acid are mixed with the concentrate and heated to the temperature range 150-300°C. Subsequently, the baked material is leached with water/weak acid and the acid bake-leach process has some advantages over conventional sulfuric acid leaching (Prater et al., 1970). During water leaching, metal sulfates are released in solution, after which they can be extracted through well-known hydrometallurgical techniques. While the majority of the work has been done on oxide minerals, there is a limited record of sulfuric acid baking of sulfides."

Jan 1, 2015

By Collon C. Kennedy, Frances C. Hartogh, C. Joel Casburn

INTRODUCTION During the nineteenth century, the federal mining law was enacted with the objective of promoting the development of the western United States by providing unrestricted access to vast areas of federal land for mineral exploration. Prior to the advent of comprehensive federal, state and local land use plans, there was little, if any, regulation or restriction of mineral exploration activities. Today, the laissez-faire policies of the past that encouraged mineral exploration have gradually given way to the public&apos;s legitimate concerns regarding environmental protection, multiple use and planned land development. As a result, the contemporary prospector confronts a maze of statutes, ordinances and regulations with which he must comply to obtain the requisite approvals and permits before commencing mineral exploration on federal, state or private lands. This presentation will provide a broad overview of the exploration permitting process. The first section of this paper recommends certain general management practices to follow when attempting to obtain exploration permits. The second section presents two hypothetical cases, one involving a drilling program on private property in California and the other involving a drilling program and the removal of a bulk sample for metallurgical tests from federal land in Nevada. The cases are used to discuss jurisdictional issues and application of certain federal, state and county laws and regulations that pertain to mineral exploration. The final section contains a brief analysis of three important recent United States Supreme Court decisions. These decisions address the scope of the federal pre-emption doctrine as it applies to activities conducted on unpatented mining claims and the constitutional limits of permissible state and local land use and zoning regulations. PERMITTING PRACTICES The environmental impacts associated with mineral exploration generally result from the construction of drill sites, roads or trenches. Consequently, after the regulatory authority has considered the issues of permissible land use, the primary emphasis of the permitting process is to address problems related to pre-construction site identification and clearance, and post-construction site reclamation. The approaches taken to address these and other related issues vary with the scope of proposed work, the site, the appli-

Jan 1, 1987

By VÍCTOR VÁZQUEZ-VÁZQUEZ, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, JESÚS L. VALENZUELA-GARCÍA, OFELIA HERNÁNDEZ-NEGRETE

The present study examined a process for precious metal recovery (silver and gold) from difficult minerals which exhibit refractory characteristics to cyanidation and ammonium thiosulfate leaching (low extraction and high consumption of leaching agent). It is well known that mangano-argentiferous minerals are mainly composed of manganese, silver, gold, and iron. In this research, a mineral sample from Monte del Favor mine, located in Hostotipaquillo, Jalisco, Mexico, was physically and chemically characterized by X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), fire assay, and atomic absorption spectroscopy (AAS). Two-stage leaching was carried out: first to eliminate manganese from the sample using sodium sulfite (Na2SO3) as a reductive reagent and sulfuric acid (H2SO4) and a second stage to dissolve silver and gold with sodium hypochlorite (NaClO) and hydrochloric acid (HCl); the results show extraction around 96% for Mn and 98.73% and 83%of Ag and Au, respectively. The usefulness of high acidity and Na2SO3 to obtain good results in Mn and Ag leaching is discussed along with the roles that HCl and NaClO play in the dissolution of Ag and Au values.

Apr 15, 2020

By Jiawang Hao, Qinglong Zhang, Liang Han, Chuhan Wang, Shenfang Chen, Lan Qiao

The surface collapse and surrounding rock failure caused by goaf instability are the mining disasters that cannot be ignored. It is of great value to evaluate the stability of goaf accurately and treat it economically for the mine safety and the maintenance of ecological environment. However, in previous studies based on numerical simulation methods, the spatial complexity and the irregularity of actual goaf were not considered. Therefore, based on the internal space data of goaf obtained by high-precision laser detector, the goaf stability was comprehensively analyzed through Plaxis software and two-stage fuzzy judgment theory in this study. To effectively improve the goaf stability, the optimal backfill parameters for the goaf treatment were obtained by a series of mechanical tests. The research results provide some good references for the stability evaluation and the treatment of underground goaf.

Sep 26, 2023

By U. S. Geological Survey Staff

"In 2017, the total estimated value of nonfuel mineral production in the United States increased by 6 percent from 2016 (Table 1). The value of metals produced domestically increased by 12 percent and the value of industrial minerals produced domestically increased by 3 percent. Some metal commodity values (cobalt, magnesium metal and palladium) increased by more than 35 percent in 2017 from 2016 owing to higher prices.Some U.S. metal mines and processing facilities remained idle in 2017, including three primary aluminum smelters in Indiana, Missouri and Washington; a titanium sponge facility in Utah and a byproduct vanadium production facility in Utah. In contrast, new gold mines opened in late 2016 and 2017 in Nevada and South Carolina, respectively, and iron ore mines in Michigan and Minnesota restarted or operated for the full year. In addition, increased oil and natural gas drilling activity led to increased production of some industrial mineral commodities that are used for oil and gas drilling. Production of some industrial minerals, especially those used in infrastructure and residential construction, remained essentially unchanged in 2017, a reflection of the limited growth in construction activity. The production of some metals, including iron and steel, aluminum and other nonferrous metals and nonmetallic mineral products increased. Overall, mining activity trended upward as the result of increases in coal mining, oil and gas extraction and metal mining (Table 2).Discussion of mine production is commonly segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, such as crushed stone or construction sand and gravel, which have higher production quantities but are lower-valued materials. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of natural aggregates are orders of magnitude larger than those for most other mineral commodities, thus making direct comparisons based on weight meaningless (Fig. 1)."

Jan 5, 2018