Search Documents

By J. W. MacDonald

PROPERTY AND PRODUCTION: Around 100 Million Tons of Recoverable Coal are available from the approximate 10,000 acres allocated to the mine. Over 1300 acres of surface land holdings extend well beyond the limits required for plant site, storage tracks, water supply reservoir, settling ponds and waste disposal. COAL: Extensive core drilled testing confirmed the early indicated high quality of the #6 Seam Washability data show less than four percent of the' coal seam required removal to provide a superior product for the available market. PREPARATION PANT DESIGN: The limited needs enabled Preparation Plant Design to meet the requirements without inclusion of novel equipment. The simplified needs afforded ample opportunity for considering increased automation where advantage or economy was antioipated. Plant design included protection of opportunity for pre-drying in advance of air cleaning the fine coal and accommodations for addition of Dense Media separating equipment in event warranted or required by future market changes. Protection is also afforded for addition of Raw Coal Storage accommodations in event warranted. Figure I shows the Preparation Plant Flow Sheet.

Jan 1, 1961

By K. Saberyan

A technique is described for the solvent extraction of zirconium. In this method, zirconium has been extracted quantitatively from 0.005 M sodium salicylate solution at pH 2.5 - 3 using 0.01 M triphenylphosphine oxide dissolved in toluene as an extractant. Zirconium has also been recovered quantitatively from 0.2 M potassium thiocyanate solution, but extractions in nitric and hydrochloric acids (as media) were negligible. The resulting extracted metal ion has been stripped with sulfuric acid (0.5 M) and determined with inductively coupled plasma atomic emission spectrometry. This method has been applied successfully to achieve 95% recovery of zirconium from zircon concentrate.

Jan 1, 2010

By J. H. Gwynne

[ ]

Jan 1, 1962

By Jack G. Quade

During the summer and fall of 1973 a series of Skylab and high-altitude aircraft overflights provided excellent hard-copy photographs of the Great Basin. These photographs, with a wide range of ground resolution were used by the NASA Project of the University of Nevada, Reno, to conduct specific geologic studies. The principal objectives of these studies were to: select individual areas covered by Skylab photography for detailed studies, develop mapping techniques using varied film-filter products with a wide range of ground resolution, compare the results of the mapping techniques to existing geologic maps at comparable scales, verify the results wherever possible by direct field observations. These studies were conducted by Jack Quade and Dennis Trexler and by graduates and undergraduates of the Reno campus under a contract with the Manned Spacecraft Center Houston, Texas.

Jan 1, 1976

By John B. Jones

New concepts in shaft kiln processing are included in the design of two large diameter shaft kiln plants now under construction. One kiln will be used to produce cement clinker at the Boettcher plant of the Ideal Cement Company at Fort Collins, Colorado. The other kiln is for the semi-commercial oil shale plant for Petrobras, the Brazil National Oil Company at Sao Mateus do Sul, Parana, Brazil. Investigations on application of the new concepts are proceeding in a portable pilot kiln. The shaft kiln has long been recognized as a method of gas-solids contacting having the following principle advantages: l. High thermal efficiency 2. Ability to handle a variety of feed materials with a wide range of particle sizes 3. Minimum investment and operating cost

Jan 1, 1963

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By Raymond E. Riethmann

El clasificador de espiral fue diseñado originalmente para circuitos cerrados de molienda. Desde entonces se ha aplicado con éxito a otros trabajos de clasificaci6n donde se necesita realizar un corte de dos productos. Inherentemente a las cualidades especiales de este cla- sificador está especialmente preparado para: clasificar, lavar, o agotar materiales tales como minerales, roca fosfática, arenas, carbbn, conchas de ostra y sales fosfáticas. Presentamos ahora las características de operation, flexibilidad de diseiio y líneas maestras para una apropiada aplicación.

Jan 1, 1982

By Y. M. Jiang

Many underground instabilities, such as excessive shield loading and roof falls, occur at longwall faces causing safety problems and production losses. Such instability problems are directly related to roof conditions which can be categorized using geological information. . However, most geologic information describing anomalies and variations of immediate and main roofs are not available before mining resulting in unexpected problems in a longwall face. It is apparent that the evaluation of these geologic anomalies provides a great benefit for longwall stability. The purpose of this study is to evaluate roof categories associated with geological anomalies employing fuzzy set theory. The evaluation is based on real-time monitoring information, such as shield leg pressure, developing load on shields, intervals of periodic weighting, and the ratio of developing loads during periodic to normal times. This paper introduces the application of fuzzy set theory for characterizing roof conditions and evaluating of roof similarities.

Jan 1, 1995

The Witwatersrand reefs provide excellent examples of chemical and structural control on gold distribution. All mined gold appears to coma from a carbon -gold association and/or Fe-S-Au association, and also from immediately above or below unconformity surfaces. A total raliance on the current syngenetic model for Witwatersrand gold does not appear to be justified from the accumulated data and may be responsible for missed opportunities during exploration: consideration of other models is suggested especially where they better fit the data. The stratabound natura of Witwatersrand gold 1& critical to mining, but is emphasized in syngenetic models to the virtual exclusion of many other important observations. By analogy with other deposit types, stratabound character is probably a poor guide to genesis.

Jan 1, 1988

By A. J. Sinclair

Los métodos de desmuestre para estudios de viabilidad dependen de las características geológicas del yacimiento que ha de ser evaluado. Se requiere un estudio geoestadístico preliminar, teniendo en cuenta los aspectos de autocorrelación de las variables sometidas a estudio, con objeto de que el plan de diseño de muestras pueda ser optimizado para producir las estimaciones de ley y tonelaje dentro de los límites de errores establecidos. En general, debe de tenderse a una distribución regular de muestras para ello, y longitudes regulares de las mis¬mas (a partir de los testigos o cortes, por ejemplo) son preferidas con objeto de facilitar los análisis estadísticos. Los planes de desmuestre son modificados y mejorados (bien técnica o económicamente) a medida que avanza el programa y es obtenida información adicional. Las muestras a granel para pruebas metalúrgicas pueden ser evaluadas en término de va¬riaciones señaladas por todas estas muestras en un depósito y la variabilidad de la ley dentro de las mismas. Una atención adecuada sobre estas fuentes de variabilidad asegurará una evaluación adecuada de los resultados de las pruebas piloto de las muestras a granel. Por otro la¬do, un estudio mineralógico general del yacimiento es un requerimiento importante, a veces ignorado, en una evaluación más general pero semicuantitativa de la representatividad de una muestra a granel; y, además, proporciona una información muy útil para optimizar el diseño de la planta.

Jan 1, 1982

By D. L. Moellenberg

Under various state laws enacted mostly within the last 20 years, reclamation requirements and standards for hard-rock mining operations have been established virtually everywhere in the western United States. Unlike the uniform and detailed coal mine reclamation requirements under the federal Surface Mining Control and Reclamation Act ( "SMCRA" ) and state programs mode led after SMCRA, the various state law hard-rock mine reclamation requirements are based upon a variety of objectives, and therefore are subject to varying standards from state to state. While the diversity of reclamation requirements complicates the determination of what reclamation measures will be required at any particular mine, there are valid reasons for this diversity. There are dozens of different commodities mined in the United States, and mining methods are different for each commodity. Local natural conditions such as climate, precipitation, geology, hydrology, and biology vary widely across the county. Site-specific conditions also affect mining and reclamation methods. Also, factors such as economics, land use, and environmental protection issues receive different priorities in different states and communities within those states. State reclamation requirements in general provide the flexibility to consider site-specific circumstances, allowing operators to design and engineer the best reclamation measures for each mining site. To the mine developer or manager, reclamation requirements must be translated into design, operational, and closure measures for mine planning. Each of these measures must then be assigned additional costs to be factored into the economic decisions for a particular mining operation. On a broader level, reclamation costs must be factored into decisions such as where to invest in exploration and mine development. The purpose of this paper is to provide a summary of the state non-coal mine reclamation requirements in twelve western states. This summary comparison may be useful as a starting point in considering how local reclamation requirements will impact potential mining costs.

Jan 1, 1994

By David J. Akers

In past years, water drainage control in coal mines has been primarily directed on the basis of water quantity rather than quality. Due to the recent intense interest in total ecology and environment, emphasis has shifted to the point where the water exiting from a mining operation may be of better quality than when it enters. In most operations this has meant the use of treatment methods (neutralization) while the technology for the prevention of acid drainage is being developed or refined. To date, underground abatement of acid formation has generally been less expensive but also less effective than surface treatment of the mine water. It seems probable that total mine water pollution control will have to include both underground abatement and surface treatment methods. The general acid producing reaction involving the oxidation of pyrite - 2FeS2 (pyrite) + 702 + 2H20 ? 2Fe2S04 + 2H2SO4 - is well known, even though the individual steps are not clearly understood. The major implication of this reaction, that acid production can be eliminated by not allowing the contact of pyrite with free oxygen or water, has been well substantiated both in the laboratory (1,2) and in practice. (3) Underground abatement or control processes can be generally classified into two types: (1) the effective control or elimination of acid causing reactions within the mine, and/or (2) the reduction or prevention of water flow into and out of the mine. Recognizing the fact that these two types may be directly inter-related, this paper will, for the purposes of clarity and simplification, discuss each separately.

Jan 1, 1973

By T. Yukimasa

Hachinohe smelter, a zinc-lead blast furnace complex with the annual capacity of zinc plus lead of 100,000 tons, had originally treated normal zinc and lead sulfide concentrates. However, it is currently handling a great variety of raw feeds ranging from complex sulfides to oxidic recycled materials in view of resource economy, most of which are unsuitable for zinc electrolysis. This paper reports on some significant efforts recently carried out on improving sintering operation, i.e., the increasing use of secondaries against harmful ingredients like halogens, and the substantial reduction in energy use as the results of various modifications and improvements.

Jan 1, 1982

By Ottmar Burghardt

Sintering of iron ore has undergone a dramatic development world-wide. Today, the annual world production amounts to approximately 600 million tons. At present, the sintering process in competition with pelletizing, seems to offer certain advantages inasmuch as it allows the use of solid fuels. Also, its charging behaviour in the blast furnace is, in general, considered as being better than that of pellets. This is true, in particular, for the charging behaviour and the gas permeability in relation to the grain size. Moreover, instead of charging limestone into the blast furnace, for instance, the basic components which are necessary for the burden materials can generally be supplied in a simpler and more cost-effective way by using basic sinter instead of basic pellets. While in sintering, with basicity rising to the range of 1.6 to 1.8 CaO : SiO2, the capacity increases and the sinter quality shows improvements in most of its characteristics, the pro¬duction of basic pellets generally requires a higher fuel rate, when compared to acid pellets, while production capacity decreases and some of the quality characteristics deteriorate.

Jan 1, 1982

By Eric Lutz

"Great effort has been expended for more than 40 years to improve the workplace safety and health of surface and underground miners across the United States. When looking at the past decade, withstanding the 2010, Upper Big Branch (UBB) disaster that took the lives of 29 miners, this effort has resulted in a generally decreasing trend from 57 fatalities (22 coal; 35 metal/non-metal) in 2005, to 45 (16 coal; 29 m/ nm) in 2014. Through August of this year, there have been 23 mining-related deaths (eight coal; 15 m/nm). These results reflect continued diligence and perseverance on the part of miners that stay true to our legacy; and demonstrate significant investments from mine-site leadership, mining corporations, and state and federal regulators. However, over the past five years there have been an average of 32 fatalities per year, with a low of 36 (2011 and 2012) to a high of 45 (2014). If we know that there will be somewhere between 30 and 50 mining related deaths next year, which of us will volunteer to be counted as one of the numbered? Clearly, we all agree that one fatality is too many; and as evidenced by changes following UBB, deaths in any sector are deaths reflective of all mining across all sectors.The impact of each miner death touches us all. Miner’s deaths are felt deeply by family and friends, most significantly the children; their communities in which they served, supported, and worshiped; and by society that has lost a hardworking, dependable contributor. Further, to take a slightly cynical, but realistic view, miner fatality events impact the financial vitality of mining and contracting companies and broadly diminish investor confidence. Just as important, these events significantly impact our communities and result in negative public perceptions, which ultimately drive regulatory policy and related compliance pressures. This resulting pressure forces operations to broadly address safety and health gaps in very specific ways (i.e., see U.S. Mine Safety and Health Administration (MSHA) regulations regarding lids for trash cans) minimizing a mine site’s opportunities for operational flexibility. To break this cycle that is the operational reality, mining companies are focusing tremendous efforts on fatality prevention and specifically on dedicated investment to prevent multiple fatality events."

Jan 1, 2015

By J. V. G. Middleton

The paper gives a comprehensive review of the design considerations which determined the choice of the milling plant, a description of the plant and comment on the operating experience to date. Operating experience will include inter alia a description of the mill liners installed with subsequent changes due to wear patterns, the mill inlet sealing arrangement, steel ball addition, mill outlet sump design, cyclone feed pump liner wear patterns and comment on the efficiency of the linear screens for wood chip and tramp removal. Finally a view on future trends in South African milling practice with respect to type and size of plant.

Jan 1, 1989

By Gene Mattila

Each installed rock bolt costs in excess of 520.00. High cost in conjunction with the primary purpose of safety makes it only logical to install the highest quality anchors possible. Each bolt has designed support capabilities in axial, shear and fluctuating ground condition, if installed to manufacturers recommendations. The quality of anchor is not; however, only affected by material specifications, but by transportation, handling storage, installation procedure, machine performance and geology. The quality is not only affected by many variables, but reliability should be assured. Non-destructive methods of testing reliability are only available for several types of bolts.

Jan 1, 1985

By Gary E. McIntosh

This paper will discuss a U.S. Bureau of Mines project designed to assess and predict the impacts which surface coal mining will have on the regional shallow groundwater systems in the Powder River Basin. The primary objective will be met through the accomplishment of the following: (1) The design and establishment of a regional network for monitoring of shallow groundwater systems in the Basin. (2) Monitoring of the direction and rate of flow, water quality, and aquifer characteristics of the shallow groundwater systems. (3) Development of a regional groundwater simulation model with appurtenant subroutines to determine local effects.

Jan 1, 1978

By R. Schlüter

"The global mining industry is facing increasing challenges in terms of geological, technological and social aspects. Potential exploi-tation of deposits shows a tendency to increasing depth with complex ores and decreasing grades. A promising approach to deal with these constrains is by applying alternative extraction methods like (bio-)hydrometallurgy as in-situ leaching (ISL) technology. The Bergakademie Freiberg University of Mining and Technology established the “Biohydrometallurgical Center for strategic Elements” (BHMZ) to foster the interdisciplinary research along the entire biohy-drometallurgical process chain to extract indium from sulfide ores. The involved Department of Underground Mining Methods deals with the design and implementation of a pilot-scale underground testing facility for microbial in-situ stope leaching in its “Research and Educational Mine”. This paper discusses the potential of in-situ bioleaching under technological aspects. In addition, different conditioning approaches based on hydraulic and explosive methods for enhanced permeability in the formation are introduced and the gathered data will be presened. INTRODUCTION A reliable, substantial and sustainable supply of raw materials is of crucial importance for any industrialized country. This dependency applies to “strategic elements” including rare earth elements (REEs), platinum group metals (PGMs) as well as a variety of other metals like indium and germanium which are needed for high-tech industry and products such as electric and electronic devices, fibre optics and laser technology (Barakos et al., 2016; European Commission, 2010). Due to the economic growth of the BRIC-countries (Brazil, Russia, India, China), the resource policy of China as well as the volatile world mar-ket prices of different metals the availability of these critical raw materi-als and therefore the dependency of the high-tech producing countries has become increasingly important (Barakos et al, 2016). Adequate supply is often affected by the increasing depth of de-posits, lower metal concentrations and more complex ore mineralogy. In addition, mining activities are increasingly restricted by their envi-ronmental and social impact and footprints. As a consequence, con-ventional mining and processing methods are limited by high energy consumption and technical constraints."

Jan 1, 2018

By James T. Curry

The steady growth of the Northwest portion of the United States over the past two decades, and the very rapid development of Northern California, Western Nevada, and Oregon in particular, led the Calaveras Cement Company people to Shasta County, California in 1957. The presence of a large deposit of high calcium carbonate limestone had been recognized for many years, but it required the momentum of an expanding economy to make these long known reserves valuable. This, plus the availability of a reliable supply of fuel in the form of natural gas, and the ready means of shipping the product to the consumer both by highway and railroad, seemed to offer the proper combination to launch a successful venture. The Calaveras Cement Company had been manufacturing cement by the wet process since 1925 at their plant at San Andreas, California. Starting with two small kilns, the plant in Calaveras County started an expansion program in 1945 that ultimately resulted in the plant as it exists today, consisting of five kilns with a combined production of 4.5 million barrels annually.

Jan 1, 1967