Search Documents

By J. Chai, Q. Yuan, B. Qiu

"Overburden strata deformation monitoring is one of the key problems in ground control. Using geophysical method through surface drilling to detect strata deformation is commonly used in the industry. In this paper, a geophysical method based on the distributed optical fiber sensing (DOFS) system were conducted in the laboratory, where a DOFS-based strata deformation monitoring experiment was performed with three physical models. The results show that the DOFS method precisely detects the rock mass deformation and strata structure forming with the Brillouin frequency shifts (BFS) representation. The BFS curves are divided into three phases, which reflects the horizontal three zones developed in the overburden. The BFS distribution presents a multiple stages form, the 1st stage corresponds to the caving zone and the 2nd stage corresponds to the fracture zone. Based on the multiple stages form, the evolution of the water flowing through fractured zone have been determined and the controlling effect of key strata over the water flowing fracture has been pointed out. In the end, the comparison validation proves the accuracy and reliability of this method, and it could be a new approach for the ground control research. INTRODUCTION Overburden rock strata above the work face space will propagate from slight deformation, part destruction to violent movement because of the underground coal mining. It is fundamental and an intrinsic requirement of ground control to monitor the mining-induced rock mass deformation.[1] Overburden strata have their significant mechanical behaviors and movement under damage deformation and fracture. Overburden strata deformation affect the mining ground pressure control directly, and performance in the relationship of supporting equipment and the surrounding rock, the mining-induced fracture distribution and the loss of underground water resource, the ground surface structure stability and the ecological environment.[2] From the perspective of the concept of safe and efficient scientific coal mining: the overburden strata deformation is an important part of mining method selection and reasonable supporting solutions decision which can solve the issues like the roof supporting force calculation, overburden fracture distribution and gas drainage, ground subsidence, separation of coal and rock control and top-coal recovery rate and so on. From the perspective of green and ecological mining: the overburden strata deformation is the key basis of studying the mining-induced ground subsidence and mining area ecological damage, and such engineering problem like environmental protection in mining area, ecological restoration in mining subsided land and the water conservation in fragile ecology area of mining could be solved based on it.[3-6] Therefore, the mining-induced overburden strata deformation is the key of ground control and needs to be controlled artificially."

Jan 1, 2017

By Sharad Mathur

The purpose of this paper is to present the benefits of high reactivity meta kaolin (HRM) in high performance cement-based systems. HRM, unlike other pozzolans, is manufactured from selected naturally occurring kaolin ore and carefully processed under stringent conditions to result in a consistent product with highly pozzolanic properties. HRM is an ultrafine pozzolan that enhances the mechanical properties (workability and strength) and chemical stability (durability) of Portland cement concrete and cement-based products. HRM is unique with respect to its white color which makes it an ideal choice for architectural applications where visual and aesthetic concerns are critical.

Jan 1, 2003

By Chris Mills

El papel de la separacion gravimétrica en la industria minera es brevemente considerado en perspectiva. Las pruebas e intentos de laboratorio y mineralógicas para el diseñio de los procesos gravimetricos son examinados poniendo especial énfasis en la selección de la tecnologia del proceso. Es tratado y comentado el material disponible en equipos para pequeña escala y trabajo de pruebas-piloto, particularmente en relación a la escalacion y a la adquisición de datos precisos y fiables. El transporte del comportamiento de los datos desde la planta piloto a la planta a escala es igualmente explicado. Son resefiados todos los tipos de equipos a escala total existentes para la separacion gravimétrica, poniendo de relieve las unidades de alta capacidad. Es considerada la disposicion de la planta y la seleccion de 1os equipos auxiliares.

Jan 1, 1982

By J. R. Hurley

The continuous flow, horizontal drum blender has dynamic properties which may be described by the same type of equations which often arise in electrical filter analysis. Furthermore, the equations may be readily solved by the same techniques used in electrical control analysis. For this reason the blender model developed is termed an "Electric Analog", although strictly speaking it is a mathematical model. Presentation of the dynamic performance of the blender as an electrical (or mathematical) model is desirable for several reasons. The model can be of assistance in correlating performance data with equipment design parameters. The model 'can be used with other process equipment models for simulation of an entire plant operation or in stability studies. In addition, the model may be useful in providing insight into the actual blending mechanism, or it may suggest a similar method of analysis for other closely allied equipment.

Jan 1, 1967

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"The history of Duluth commences with Daniel de Greysolon du Lhut, one of the explorers of the Upper Mississippi who came to the head of the lakes in the summer of 1679. Radisson and Groseillier, and Claude Allouez, a Jesuit priest, are supposed to have visited the head of the lakes, -but there is no authentic record previous to that of du Lhut.In 1792, the fur traders established a fort at Fond du Lac, fifteen miles up the St. Louis River from Lake Superior, but within the limits of the present city •of Duluth. In the early 50's, there were a few scattering settlers at Oneota and around the George Stuntz trading post on Minnesota point. In 1855-6, the settlement on Minnesota point was called Duluth, commemorating the name du Lhut, and organized as a town in 1857. The first board of trustees and town council consisted of -William Nettleton, J. B. Culver; Robert E. Jefferson, Grin W. Rice and William Old: In 1870, the city of Duluth was incorporated, and five years later a portion of the same territory was incorporated as the village of Duluth, and the two municipal corporations were still in existence on March 1, 1887, when the city and the village of Duluth were incorporated as the present city.The first saw mill in Duluth was erected in 1856-57, on the present site of the ship canal. It cut logs from a virgin forest at the upper end of Minnesota point.The first railroad was built to the head of the lakes in 1870. The charter for this road had been granted in 1861 to the Lake Superior and Mississippi Railroad Company, afterward called the St. Paul and Duluth, and which is now a part of the Northern Pacific Railroad."

Jan 1, 1920

By A. G. Naguib

In essence, any magnetic separator operates on the basis of imparting a preferential magnetic force on particles of higher magnetic susceptibility which are to be separated from particles of lower magnetic susceptibility. A certain amount of directional deviation to the particles takes place thus allowing for collecting each category of particles separately. The forces in action on particles in a wet magnetic separator of the established designs can be analyzed in a simple manner as shown in Figure 1.

Jan 1, 1972

By John R. Wright

This paper reviews the increased use of mechanization in order to develop lateral headings efficiently and economically. Particular emphasis is placed on the role of the Electric-Hydraulic Drill Jumbo in achieving this goal. Also, the use of modified mining equipment to suit various operating conditions is discussed.

Jan 1, 1981

By D. Tao

Coal is a major source of energy in the U.S. and more than 51% of the electricity used in the country is generated from coal. Coal cleaning prior to combustion is necessary and often accomplished using wet physical processes at coal preparation plants to remove impurities such as ash, sulfur, mercury. However, the resultant clean coal product still contains a significant amount of impurity due to the fact that impurities are not well liberated from coal particles ranging from several millimeters to inches in size at which wet cleaning processes take place. A cleaner coal product can be obtained if a cost-effective dry process is developed to further clean pulverized and thus better liberated fine coal at the power plants prior to its combustion. The benefit of such a process is a significant reduction in the cost of expensive post-combustion chemical cleaning processes such as flue gas scrubbing employed to meet the stringent environmental air quality regulations. In this study, a novel rotary triboelectrostatic separator (RTS) was investigated for its application to dry cleaning of fine coal samples acquired from the power plants in the state of Illinois. The pulverized fine coal contains well liberated ash and pyrite minerals and is an ideal feed to the triboelectrostatic separator for further cleaning without the use of water or any chemical reagents. The proprietary rotary triboelectrostatic separator (RTS) is characterized by an innovative high efficiency rotary charger, charger electrification, laminar air flow, and specially designed electrodes. Compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator offers significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range, etc. Testing with several fine coal samples has demonstrated that this technology can significantly reduce ash content with a process efficiency similar to or better than froth flotation. Important process parameters such as charger rotation speed, injection and co-flow rate, feed rate were investigated for their effects on separation performance.

Jan 1, 2010

An insufficient hydrologic data base exists for most large and small coal basins in Alaska owing to the lack of need in the past to collect data. The runoff process is insufficiently understood which is complicated by specifically northern phenomenon, and the lack of understanding of hydrologic relationships in permafrost environment. This paper presents an understanding of the hydrologic effects of frozen ground and presents methods by which the influence of surface mining upon the hydrologic balance can be analyzed.

Jan 1, 1988

By R. E. Brewer

Phelps Dodge Mining Company (Phelps Dodge) is operating a pressure leach vessel (PLV) for copper concentrates at the Bagdad Mine facility in Arizona. This single PLV unit was engineered and constructed based on continuous laboratory testing, reaction chemistry and kinetics, and available pressure vessel technology. The challenge of designing for optimum process retention time, agitation, oxygen mass transfer, temperature and pressure will be reviewed in this paper. The PLV interior lining, agitation equipment and compartment configuration chosen for the PLV will also be reviewed.

Jan 1, 2004

By E. W. Hawk

The power generation industry may be required to reduce CO, emissions if regulations related to global climate change are enacted. Coal-fired generation, which emits 82% of the power sector CO2, would be a likely target for CO2 reduction. Compliance with the Kyoto protocol will require a 30% reduction from the projected year 2012 emission level even with moderate load growth. This paper describes an analysis of power industry CO2 reduction options and their costs to assess how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered.

Jan 1, 1999

By D. M. Larsen

Since start-up in 1985, the Cannon Mine has produced and shipped a 170-g/ton (5 oz/ton) gold flotation concentrate to various smelters for gold and silver recovery. Several processes have been investigated to economically produce done' at the mine site from the refractory concentrate. This paper describes laboratory and pilot scale test work used in the process design and engineering. feasibility study of a 73-t/d (80 stpd) pressure oxidation and carbon-in-leach (CIL) facility. The designed pressure oxidation circuit utilizes a series of verti¬cal autoclave units operating at 170°C (338F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1993

By J. M. Keating, R. L. Wiegel

Those processing plants which depend on flotation for their mineral separations are always looking for reagents which are cheaper, more selective or in some other way may provide improved economic performance. This paper describes the rationale for and some results from applying a statistically based approach to reagent testing in those flotation plants which still rely on experienced operators for manual flotation control.

Jan 1, 1986

By S. K. Kawatra

It has been observed in some mineral processing plants that grinding circuit efficiency varies seasonally, such as in some plants which are located in the northern U. S. and Canada and undergo large seasonal temperature changes, with the grinding circuit efficiency different between summer and winter. This indicates that the temperature of grinding circuit slurry has a noticeable effect on grinding performance. The effect has rarely been studied. To this end, an investigation to examine the effects of changing temperature on efficiency and determination of the mechanism responsible has been carried out. Plant investigations and laboratory experiments have been conducted in order to study hydrocyclones. It was demonstrated that under otherwise constant operating conditions, the d50(c), size decreased linearly with increasing temperature, while the shape of the reduced efficiency curve remained constant. This effect was determined to be due to changes in slurry viscosity with temperature.

Jan 1, 1988

By W. F. Quirk

The Missouri-Oklahoma tripoli district was discovered and first mined in 1869 near Seneca, Missouri. Tripoli is a microcrystalline form of high-purity silica that is porous, light- weight, and friable and is derived from a parent siliceous sedimentary rock from which soluble minerals have been leached. Tripoli deposits, 2 to 20 feet thick, occur in cherty limestones of Mississippian age beneath 2 to 10 feet of overburden. They are mined in open pits up to 9 acres in size. The color of tripoli is white, but it also commonly is light pink or red where stained by red iron oxides and clays. Ground tripoli is used commercially as an abrasive or in buffing and polishing compounds and is prized for such physical characteristics as its abrasiveness, porosity, permeability, absorption, and specific gravity.

Jan 1, 1978

By Robert J. Mac Kinnon

A moving grid finite element model for the analysis of transients in a rock mass surrounding an underground coal conversion cavity is presented. Major model components are outlined, including a special element formulated to account for internal discontinuities. A numerical example is described.

Jan 1, 1986

By Robert F. Droullard

The U. S. Bureau of Mines (USBM) has investigated instrumentation and methods for measuring exposure to radon daughters in underground mine atmospheres. Both personal and area monitors have been studied through in-house and contract research. A field study in uranium mines identified some reliability problems that required additional work for the personal dosimeter systems. Improved versions of continuous working level detectors have been developed and tested for use as area monitors in underground mines. Test results for the personal and area monitors were satisfactory for underground mine applications.

Jan 1, 1981

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By J. Launay

In order to control and dispatch the sewage water coming from 3 tunnels toward 2 downstream sewage tunnels, a large cavern has been excavated in a suburb of PARIS. Located at a depth of 47,00 m, it has been excavated using the NATM procedure through swelling clay, weathered sandstone, and marl and chalk. It is 16,50 m high, 12,40 m wide and 60, 00 m long, with an elliptical cross-section and its two ends are egg-shapped. The final lining of the cavern is composed of 30 to 40 cm of shotcrete, steel ribs and passive anchor bars. The excavation stages and related movements were surveyed by extensometers, pressure cells and convergence devices. The design, method of construction of the cavern and the results of the measurements made are commented.

Jan 1, 1989

By E. S. Peterson, M. K. Harrup, K. A. Dolbeare, J. E. Wey

Efficient methods for removal of copper from heap leach solutions without mobile organic phases are a current mining industry need. To satisfy this need a selective, high-capacity, durable solid material is required. The INEEL has developed a set of materials based upon current solvent extraction chelates that provide selective copper concentration in the presence of high concentrations of iron. In contrast to conventional solvent extractions, our strategy anchors the chelators to a non-polymeric solid substrate through the use of a custom designed linker molecule. The fundamental synthetic routes to these materials have already been established and attachment to the solid surfaces achieved in an efficient manner. Our continuing research is focused on the optimization of the synthetic pathways to these solid materials and the evaluation of their copper capturing capabilities.

Jan 1, 2002