Search Documents

By R. F. Korcak

There exists a wide array of industrial byproducts that produce beneficial responses in the soil/ plant environment. These materials range from clean-coal-technology residues produced during the generation of electric power (particularly those high in gypsum) to mineral fines produced by the aggregates industry (i.e., sand, gravel and crushed stone). A number of these materials are examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems are discussed.

Jan 1, 1997

By J. W. Merks

At mineral processing plants the accuracy and precision characteristics of assays in mill feed, tailings and concentrate largely determine the reliability of the metallurgical balance. The accuracy of measurements is ensured by selecting effective sampling methods and efficient sample preparation procedures, and by effecting each phase without introducing a systematic error while the precision of measurements is determined by the sampling regime. Sampling systems and components, sampling methods and regimes, and sample preparation procedures will be reviewed. Different techniques to determine variance components for sampling, preparation and analysis, and to detect systematic errors in assays at mineral processing plants, will be discussed.

Jan 1, 1986

By K. A. Natarajan, M. K. Yelloji Rao

Significance of grinding media wear and its effect on chalcopyrite flotation are discussed. Laboratory marked ball wear tests were conducted grinding chalcopyrite ore and quartzite dry, wet, and with collector added during grinding. The effects of oxygen and nitrogen on ball wear were evaluated by the addition of chalcopyrite mineral while grinding quartzite. The effect of dry and wet grinding on chalcopyrite flotation was also studied. Results show abrasive wear is greater in quartzite grinding than in grinding chalcopyrite. Oxygen increases the corrosive wear of high carbon low alloy steel balls in the presence of chalcopyrite ore. Chalcopyrite flotation was retarded due to wet grinding in the presence of oxygen. Though collector reagent increased the media wear, it improved the flotation of chalcopyrite. Probable electrochemical reactions encountered in a grinding mill are outlined.

Jan 1, 1991

By R. Stanevich

Studies by the National Institute for Occupational Safety and Health (NIOSH) and the Bureau of Mines (BOM) have demonstrated that: (1) 90% of diesel particulate is less than one (1) micrometer in aerodynamic diameter; (2) more than 90% of the respirable mass in electric coal mines was greater than one (1) micrometer in aerodynamic diameter; and (3) in coal mines using diesel equipment, average diesel concentrations can represent up to 53% of the MRE respirable coal dust standard. For mines approaching the 2 mg/m3 standard, compliance may be easier to attain by controls directed at diesel exhaust particulate as opposed to coal dust control. First, however, a Simple instrument is needed to measure diesel exhaust particulate concentrations. This paper describes such a sampler, its construction, and use. While results from this sampler are primarily utilized to identify control areas, NIOSH is also using the sampler for estimating worker exposures in epidemiologic studies.

Jan 1, 1988

By Glenn H. Damon

Concern about environmental pollution goes back many centuries, but until recently most efforts to control it have been perfunctory and spasmodic, aimed largely at coal smoke and other visible pollutants. Air pollution is to a large degree a byproduct of our economic development, and scientific knowledge of the causes and character of such pollution is more extensive than the technology to handle the waste byproducts of our industrial civilization. The removal of all constituents foreign to the air from the effluents produced by an industrialized society is obviously impractical at this time. There is widespread difference of opinion regarding acceptable ambient air concentration levels for the Various pollutants produced by combustion processes, but there is basic agreement that the pollution of the atmosphere must be controlled and eventually reduced. The magnitude of the air pollution problem has been increasing rapidly because our expanding economy calls for an ever-increasing consumption of energy, and fossil fuels are a principal source of energy. For example, the consumption of electricity has been increasing at an average annual rate of approximately 8 percent over the last 10 or 1.5 years. Table 1 shows the estimated emission of the principal pollutants into the atmosphere in 1966. The approximately 90 million automobiles, trucks, and buses on American highways contribute the largest proportion of pollutants to the atmosphere, but that fact does not alter the growing problems of the coal industry. You will note that sulfur oxides, particulates, and nitrogen oxides are all products of the combustion of coal. Of these air contaminants, sulfur oxides are now receiving major emphasis in terms of research to develop effective means for control, Table 2 shows that the combustion of coal produces approximately 60 percent of the sulfur oxides discharged to the atmosphere. While the utilization of coal is the principal source of particulate matter, this is not considered as serious a problem as it was in the early part of the century because of technological developments that have produced sound methods for the removal of particulates from waste gas streams.

Jan 1, 1968

By S. R. Maynard

The Ortiz Mountains lie 25 mi (40 km) northeast of Albuquerque, New Mexico in Santa Fe County (Figure 1). Approximately 350,000 ounces (11,000 kgs) of gold have been produced from the Ortiz Mountains since the 1820s. The 100 square mile (260 square km) Ortiz Mine Grant was secured from the Mexican government in 1833 by Jose Francisco Ortiz for the purpose of mining gold. The Grant has remained more or less intact to the present. The mineral rights are currently owned by Ortiz Mines, Inc. of Joplin, Missouri and are leased to LAC Minerals, USA, Inc. (west half) and to Gold Fields Mining Corporation (east half).

Jan 1, 1989

By M. Z. Rashad

The intersection of joint sets and excavation planes leads to removable blocks which can be expected to fall or slide. The amount and cost of supports required to stabilize these blocks of excavation are related to the number and dimensions of key blocks, the mechanical properties of joints and the active forces present. In this work, the application of the block theory in the study of the kinematics and stability of removable blocks is investigated considering any number of sliding faces for some Egyptian limestone quarries.

Jan 1, 1993

By F. Milton Lewis

In this paper an attempt has been made to review the cost trends in producing copper by conventional milling. smelting and hydro-metallurgical means during the last five years. The primary objectives of this cost analysis are to provide a base for future projections as well as to indicate which cost items are more volatile in their influence on overall cost of producing copper.

Jan 1, 1977

By Viktor Tokle, C. W. Dawson

The Devico directional core drilling system and its capabilities are described, with reference to other directional drilling technologies and the advantages and disadvantages of these systems. The advantages and disadvantages of a number of borehole navigation systems are also presented. A discussion of the applications of the technology follows, illustrated by case histories. Finally, the environmental impacts and benefits of the technology, in comparison to more conventional systems, are presented.

Jan 1, 1999

By W. H. Wilson, G. Bjarnholt, D. C. Holloway

This paper describes the results of field tests conducted on a 5x25m bench face to evaluate several new concepts for improving smooth wall blasting. These ideas involved the use of notched boreholes to direct the fractures and unconventional types and placements of explosives. The notches were made with a mechanical broaching tool, a water jet and with shaped charges. Borehole pressures were measured with an inexpensive and expendable pressure transducer developed for this program. The testing showed that at hole spacings 38% greater than normal practice, notched holes with half the normal loading density produced equivalent results.

Jan 1, 1986

By Mark Cadzow, Rodney Lamb

CARBAD is a recently developed Australian process for the recovery of gold and platinum group metals (PGM). The process relies on the selective agglomeration phenomena of the gold and PGM to capture the mineral in a carbon-hydrocarbon media. The precious minerals are then extracted from the loaded media by a solvent gold room process producing a relatively pure concentrate. The media is then reformed and recycled. The process development from batch test work to a 5 t/h commercial scale CARBAD plant is discussed. The operation and results of processing a variety of ore types at several alluvial and hardrock gold mines is examined. The operating and capital costs for the CARBAD process shows that it is significantly less than that the conventional CIP/CIL. The environmental safety of the process is a major feature where precious metal deposits are located within urban environments or within wilderness areas.

Jan 1, 1989

By B. K. Parekh, R. H. Mehta

Handling of fine coal is an importance issue for coal as well as the utility industry. Reconstitution in form of pellet or briquet would be desirable if it could be done economically. This paper evaluates the effectiveness of three binders e.g., asphalt- emulsion, corn starch and Brewex, in forming pellets of ultra-fine clean coal. It was found that asphalt emulsion and corn starch were not effective binders for ultra-fine clean coal, however, Brewex provided excellent quality of pellets, which exceeded all the minimum quasi requirements of coal pellets. INTRODUCTION Advanced coal preparation techniques (physical or chemical) are designed to process ultra-fine (minus 200 mesh or 74 pm) coal. The average particle size of the clean coal product is about 25 pm. Currently available dewatering techniques are effective in providing a 25 to 30 percent moisture product of this size coal slurry (Parekh et al. 1989). Handling and utilization of this dewatered ultra-fine size coal is difficult. Reconstitution, which includes pelletization, briquetting, extrusion, etc., of the dewatered coal product provides an ideal answer to handling and transportation problems. However, reconstitution of fines in the coal industry has not been successful due to various reasons. The most important criterion for its unsuccessful application in the coal industry is the cost of the binder (Capes et al. 1965). Various methods of reconstitution, such as briquetting, disk pelletization, extrusion pelletization and roller and die-pelletization, have been tested for fine coal agglomeration (Conkle et al., 1991) (Richards, 1990). Conkle et al., (1992) have provided a detail analysis of each technique in terms of moisture and operating cost requirements. According to Conkle, briquetting requires a product containing very low moisture, whereas pelletization can be done with coal containing up to 30 percent moisture. Currently available dewatering technique provides about 25 percent moisture product, thus, pelletization appears to be an ideal route for reconstitution. In this paper, results are presented on the comparison of three different binders i.e., asphalt-emulsion, corn starch and Brewers condensed solids (BCS or Brewex), for fine coal pelletization.

Jan 1, 1995

Table A. Conversion of English to SI Units Table B. Strength Properties of Rocks Table C. Engineering Properties of Rock Table D. Properties of Common Minerals Table E. Material Properties and Characteristics Table F. Heat Value of Various Fuels Table G. Geometrical Relationships and Mensuration Formulas Table H. Standard Sizing and Meshes Table I. Ship Measures Table J. International Atomic Weights Table K. Time Value of Money Factorsfor Discrete Compounding

Jan 1, 2008

By D. R. Lanners

Samples of the same coal measure overburden spoil were obtained from three different mine sites. Site A used a 27-m3 tub-mounted dragline, Site S used a front-end loader and truck combination, and Site C used a 6-m3 crawler-mounted dragline. The spoils were analyzed in the laboratory for the strength parameters using drained triaxial tests conducted on 150-mm diameter specimens. Regression analysis was utilized to determine the appropriate failure criterion for the strength data from each site. Spoil obtained from Site S yielded higher shear strengths than Sites A and C.

Jan 1, 1993

By R. Haecker, S. Gupta, P. Somasundaran

Rock disintegration processes are usually inefficient and costly operations in mineral beneficiation, mine development and oil well preparations. Thus, there is a strong need for improving the energy efficiency of unit operations such as drilling and comminution. The effects of selected cations and anions on drilling efficiency in a hard rock formation (Dakota Sandstone) were studied. The zeta potentials and the tensile strengths of the drilled samples were measured under similar chemical conditions. The chemicals tested included MgCl2, Na2CO3, AlCl3, NaCl and Dodecylammonium chloride. The results indicated that drilling rates can be enhanced or retarded depending on chemical conditions such as the solution pH and the type and concentration of reagents. Drilling data are correlated with mechanical (tensile strength) and interfacial (zeta potential) properties of the rock formation. The mechanisms involved are discussed in light of Rehbinder's and Westwood's theories.

Jan 1, 2000

By J. van der Walt

In hot deep mines the ventilation and refrigeration requirements are determined primarily by the magnitude of the various sources of heat, and where in the mine they arise. Refrigeration is expensive, and in order to ensure that it is utilized effectively and at the lowest possible operating costs it is important that careful attention be given to the selection of plant, and how the cooling is to be distributed. The paper outlines the essential features of the highly effective strategy that has evolved in recent years in cooling deep mines in South Africa.

Jan 1, 1980

By Paul F. Ph. D. Ziemkiewicz, Courtney D. Black

According to the American Coal Ash Association, 105 million tons of coal combustion products (CCP) were produced by the power generating utilities in 1997. Of that total, 1.68 million tons were used in mining applications (ACAA, 1997). Results have ranged from the environmentally beneficial to neutral and, in some cases, detrimental. Twenty years ago coal ashes: bottom and fly ashes constituted nearly all CCPs. With the shift to new emission control technologies at power plants, however, large volumes of new products are being generated. Many do not lend themselves to traditional ash applications such as cement formulation. Many CCP disposal sites are not documented with reliable pre and post application monitoring. In this report we discuss types of CCP, their relevant characteristics and the mining environment. We have attempted to identify a range of documented applications and to draw conclusions about their environmental effects including benefits and adverse impacts.

Jan 1, 2000

By Wayne Wride, Amy Lamb, Debra Sonntag

In today's "information age", we have the ability to collect volumes of data about a company's performance. The challenge is to turn that data into information employees can understand and use to fine-tune equipment, modify work processes, and ultimately manage production. Software programs have increasingly given end users control over what data is used and how it is presented. Kennecott has implemented an information system capable of collecting and storing data at the primary level. This enables plant personnel to transform historical data into information for action. Kennecott plans to expand its data collection and use trending and reporting capabilities to move toward a fully optimized operation.

Jan 1, 2000

By Gösta W. Diehl

During the past five years the use of all-hydraulic drilling equipment has increased rapidly, and we have now reached a point where the hydraulic drill has become an alternative to be seriously considered for every drilling operation. The hydraulic drills have many advantages over pneumatic drills, but they also have certain characteristics, which makes a potential user hesitate before making the switch. And when the decision to use hydraulic drills has been made, the user then faces another choice of equal difficulty: the choice between different hydraulic systems. This paper discusses some of the factors to be taken into account when considering hydraulic drilling equipment for rapid tunneling in hard to medium hard rock. THE CHOICE BETWEEN HYDRAULIC AND PNEUMATIC EQUIPMENT The choice between a hydraulic and a pneumatic drill is much more than just that: It is a choice between two different systems. The choice is usually based on the productivity, economy or ergonomy of the system. However, also other factors should be considered, such as service capabilities and training requirements. And finally the choice will be influenced by the need to acquire know-how in the new technology. Productivity If the prime consideration is to achieve the highest possible tunneling speed, then the high penetration rates of the hydraulic

Jan 1, 1979

By Lucien Duckstein

The purpose of this paper is to give recommendations for utilization of water resources in a mining region, considering also water supply and environment; the case study of mining for coal and bauxite under the karstic aquifer of the Transdanubian mountain of Hungary is used to illustrate the approach, which consists in formulating a static multiobjective control model and solving it by compromise programming. The three activities of regional mineral resource exploitation, water supply and environmental protection are represented by different objectives which cannot be expressed in commensuerable units. Thus, a solution which is optimal for one objective is usually far from being optimal with respect to the other two objectives. As a result, we are not seeking an optimal solution for the conjunctive regional system, but a good compromise, trade-off or "satisfactum" (1), (2).

Jan 1, 1979