Search Documents

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Jamal Rostami, Tala Tahernia

TBM utilization rate is a component of machine performance prediction and critical for developing a reliable estimate of the construction completion time and cost of the tunnel. Estimation of the utilization rate involves identifying and quantifying the time dedicated to each activity in a tunneling jobsite. Ring building is a common activity in TBM tunneling and takes a large amount of tunnel excavation time when using shielded TBMs. This paper concentrates on the effect of tunnel diameter on the duration of downtimes related to ring building and examines the impact of machine diameter on downtimes. For this purpose, the dependency of segment installation time to segment configuration, and also the diameter of the tunnel was investigated. Furthermore, the ring building time for four tunnels with different sizes of diameters and a variety of ring arrangement were analyzed and the relationship between TBM diameter and segment installation time and consequently TBM utilization was evaluated.

Jun 13, 2021

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

To provide critical scientific data and engineering guidelines to federal and state regulatory agencies as well as the coal and gas industries, the National Institute for Occupational Safety and Health (NIOSH) initiated a Gas Well Stability Research Program in 2016. This paper summarizes the critical scientific data acquisition, interpretation, and modeling by NIOSH regarding the stability of unconventional shale gas wells influenced by longwall mining. Currently, NIOSH is the only organization in the U.S. conducting such fundamental and impactoriented research, which receives input and collaborations from MSHA, PADEP, WVDMS, OHDNR, the coal industry, and the gas industry. Results from the NIOSH field instrumentation programs—which include surface, subsurface, and underground instrumentation—and the parallel three-dimensional numerical modeling programs indicate that, under shallow and medium covers, the measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Casing couplers are found to play an important role in longwall-induced casing deformations. Cementing alternatives are found to have significant impact on longwall-induced casing stresses and deformations. Measured 60-arm caliper logging results are in good agreement with three-dimensional computer simulation results. Engineering guidelines on longwall-induced deformations, casing and cementing alternatives, gas well setback distances, as well as risk assessment strategy are proposed.

Mar 2, 2022

By A. M. Johnson

Although known primarily for native copper, the Keweenaw Peninsula of northern Michigan also has deposits of copper sulfide (chalcocite) ore. A number of small, but rich, deposits are present at relatively shallow depths near the base of a thick, steeply dipping sequence of volcanic and sedimentary rocks. Because much of the ore is fracture-controlled, the deposits appear to be ideal candidates for in-situ leaching. Fracture mapping from drill core and borehole logs coupled with borehole packer permeability tests are being applied to evaluate the suitability of the ore for in-situ leaching. A leaching scheme utilizing a bacterial-assisted ferric iron lixiviant is being tested at bench scale. A pilot scale test is being designed to evaluate the system in the field.

Jan 1, 1988

By Y. C. Guan

In an attempt to replace the traditional cyanide process of extracting gold, a new technology using ammoniacal solutions has been developed. In this study, the electrochemical behavior of gold in ammoniacal solutions at temperatures above 100°C has been investigated. An electrochemical cell in an autoclave has been introduced to carry out this study. The system consists of a gold working electrode, a platinum counter electrode, and an external saturated calomel electrode (SCE) which is connected to the autoclave system through a Birch wood plug. Techniques used in this study included potentiodynamic polarization, galvanostatic polarization, cyclic voltammetry, and Tafel polarization. The electrochemical reaction mechanisms governing the dissolution process are presented.

Jan 1, 1996

By Chester R. McKee, Amar C. Bumb, Kohei Kawakita

Unlike many other heavy metals, gold can be profitably mined in small operations because of the prices. One mining technique that seems ideally suited for small deposits of gold and for certain large, lowgrade oxidized disseminated deposits is solution mining. Solution mining generally requires lower capital investment and operating costs than conventional mining and milling and is safer and less degrading to the environment. Although gold has long been recovered by cyanide leaching following conventional milling, solution mining as discussed here gained momentum only in the past two decades, during which time alternative lixiviants instead of cyanide have been researched. Chamberlain and Pojar (1981) classified solution mining systems used today as three types, namely heap, dump, and in-situ leaching.

Jan 1, 1990

By G. H. Jardine

Mine planning and production scheduling in surface mines are basically iterative processes which are ideally suited to the use of computer-based techniques. Both processes are truly three-dimensional and lend themselves to the application of 3-D interactive graphics. Until recently, this has applied the need for the costly, dedicated graphics screens and mid range minicomputers. However, ongoing advances in processor chip design led to the emergence of inexpensive and powerful 5 to 10 Mips desktop work- stations. These workstations have the processing power to support rapid, high resolution, 3-dimensional graphics. By combining these workstations with powerful 3-D CAD software and, with a suite of comprehensive mine planning and scheduling applications, Mincom has developed a most cost effective solution to modern mine planning challenges.

Jan 1, 1989

By J. Szarkowski

"INTRODUCTION The Butte district of Montana is well-known as one of the biggest historic producers of copper in the world. It is also a classic example of a porphyry Cu-Mo system that has been overprinted by zoned, polymetallic (Cu-Zn-Pb-Ag) lode mineralization. After copper, silver was the next most important metal mined from Butte, with over 700 million ounces of total Ag production between 1880 and the present day. Although many papers have been written on the mineralogy of the early porphyry Cu-Mo mineralization and the high-grade Cu-rich lodes in the center of the district, relatively little information exists on the mineralogy of silver in Butte. The purpose of this paper is to summarize past and present silver production trends for the district, and to combine previously published work with new research to examine the mineralogy of silver in the Butte mining district. BUTTE HISTORIC SILVER PRODUCTION According to a recent USGS compilation1, Butte is one of the most Ag-rich porphyry deposits in the world, both in terms of average Ag grade (8.6 g/ton) and total production + reserves (Fig. 1). It is also the 2nd biggest Ag-producing mining district in the U.S. (after the Couer d’Alene district, Idaho). Annual silver and copper production data for the Butte district, compiled from various sources2,3,4, are summarized in Figure 2. Peak production of Ag and Cu was in 1917. While Ag production gradually declined in the ensuing decades, Cu production remained strong until the years leading up to the closure of the Berkeley Pit in 1982. In 1984, mining of the nearby Continental Pit resumed under a different operator, and continues to the present day. The Continental mine produced an average of 35,000 metric tons Cu and 575,000 oz Ag per year between 1984 and 20044. These figures do not take into account a period of mine closure in 2001-2003 due to an unexpected hike in utility prices. The long-term decline in Ag/Cu ratio of ore mined in Butte (Figure 3) is due to several factors, including: 1) changes in metal prices; 2) a downwards decrease in Ag/Cu ratio of most of the lodes with depth below surface; and 3) a shift in mining methods from selective underground mining of high-grade veins to open-pit mining of the bulk rock."

Jan 1, 2016

By S. Eugene Sankey, Geoffrey L. Payne

Fundamental choices in flocculant selection often come down to the lower cost of solid grade products versus the convenience of liquids. The ideal product would be a low cost solid grade flocculant which requires minimal handling and no sophisticated dissolving equipment. Recent polymer developments have lead to the commercialization of a limited range of dry polymers that can be screw fed at controlled rates directly to process streams without the need for predissolving. Other developments include dry polymers that can be directly added to mix tanks without the need for sophisticated wetting systems. The latter will make dry flocculants especially attractive for smaller users. Examples of these new products and their application in industrial and municipal waste treatment will be provided.

Jan 1, 1994

By L. B. Phelps

This paper focuses on the use of an integrated mine planing software package entitled "REMINE" which was constructed to provide a project evaluation tool for analysis of remining projects. Coal remining constitutes the affecting of sites which have had a past history of mining and have a pre-existing pollutional discharge. Such sites require a Best Professional Judgement (BPJ) analysis. The program was written to provide such an analysis with flexibility in the mine plans which can be analyzed. The process required for a BPJ analysis will be detailed and mine plan simulation performed to demonstrate the analysis.

Jan 1, 1990

The Putnam Coal Mine, at design capacity, will be the third largest underground bituminous coal mine in the world and will feature the world's longest single flight belt conveyor. Construction is now in process; initial mining will commence in early 1969 and design capacity will be reached in 1971. I'm Jerry Workman, Assistant Mining Manager for the Coal Group of the Mining and Metals Division of Union Carbide Corporation, and I am acting as Project Manager for installation and start-up of the Putnam Mine. The Putnam Coal Mine reserves are located in south-central West Virginia and contain approximately 27,000 acres of prime Pittsburgh No. 8 coal; reserves are sufficient to support a 3.5 MM tons per year operation for over 30 years. The mine portal area is located some six miles inland from the Kanawha River. The river loading facility is located approximately 156 miles by way of river from the market.

Jan 1, 1968

By Patrick Shea

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management, U.S. Forest Service and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the National Park Service, U.S. Forest Service and Bureau of Land Management. The U.S. Department of the Interior has worked with the U.S. Geological Survey, the U.S. Forest Service, the U.S. Environmental Protection Agency, and western state governments to identify and prioritize these sites on Bureau of Land Management, National Park Service and U.S. Forest Service administered lands. This presentation will discuss the accomplishments we have made to date to clean up inactive and abandoned mine sites, focusing primarily on lands administered by the Bureau of Land Management.

Jan 1, 2000

By F. T. Paleari

Radial gas holdup profiles have been measured in a 50x400 cm flotation column using a multi-cell conductivity probe. Three different bubble generation systems were examined: up to eight vertical filter cloth spargers, three horizontal filter cloth spargers, and three (horizontal) Cominco-type spargers. The variables tested were: number of spargers, symmetry of their arrangement, and height above spargers. Batch water with up to 20ppm frother concentration was used. The general observation is that the profiles tend to be uniform (i.e. flat) with some exhibiting a slight wavy shape. The vertical sparger arrangement proved the most difficult to achieve profile symmetry. The horizontal spargers gave uniform profiles at right angle to their length but a decreasing gas holdup along their length; the Cominco-type spargers gave slightly less scatter in the data. Switching off selected spargers (to simulate malfunction) did not produce strong asymmetry in the profiles.

Jan 1, 1993

By V. O. Tenorio, A. M. Sanzana

"INTRODUCTION This report summarizes a research about mines which are transitioning from surface to underground mines. It is a guide to make strategic decision in these increasing amount of mines. Capital and operating costs are linked with major strategic decisions in the exploitation of an ore body. This is the reason to analyze costs related to this transitioning world trend. There are multiple reasons for transitioning from Open-Pit (OP) to Underground (UG) mining. The primary economic incentive for going UG is that the cost per unit of ore from OP mining eventually exceeds that from UG extraction. This is due to the excessive amount of waste that must be extracted when the depth of the pit increases. In addition, the reduced footprint of UG operations contributes to diminish the environmental impact on the surface. Furthermore, it becomes more difficult to find new, easily accessible ore deposits. Then, a cost model helps to guide strategic decisions in the transition from OP-to-UG mines. Objectives • Propose a methodology to guide strategic decisions in the transition from OP to UG mining. • Create an integrated cost model based on existing OP and UG individual cases. • Identify and characterize a group of mines transitioning from OP to UG. • Analyze operating and capital costs of a particular transitioning from OP to UG mine. MAIN CONCEPTS Open Pit Mining (OP) The main decisions in OP mines are: Cut-off grade, Stripping Ratio (SR), equipment size, stockpiling, pushback sequencing and processing capacity. The stripping ratio is measured as the tonnage of waste required to be removed to reach and extract one tonne of ore. The material extracted from an OP exploitation can be classified as waste and ore. This classification depends on the cut-off grade. The cut-off grade indicates the minimum amount of material with economic value in a block. The waste from the mine is going to the waste dump and the ore is going to stockpiles where will be store and then going to the processing plant (leaching or concentrator). The waste of this process is going to the tailing pond big pools. And the product is sell in the market. Another important issue is the mining capacity which is going to define the investment in mining equipment. Underground Mining (UG) The first decision to be made in order to open an underground mine is selecting the mining method. Caving methods are the more productive and have lower operating costs. There are three caving methods: Block Caving (BC), Panel Caving (BC) and Sublevel Caving (BC). The access development could be an horizontal adit or a straight or downspiral decline. A shaft could be used for inclined or vertical access. Other key issues are: equipment capacity, cut-off grade and production sequencing."

Jan 1, 2016

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995

By E. Fidler

A recent headline in the Wall Street Journal declared, "trendy management schemes very often fail." Many of the management techniques addressed in the accompanying article are associated with quality management including reengineering, benchmarking, total quality management, and employee empowerment. The article made the point that executives, employees, and customers who are involved in such programs rate the effectiveness of these programs very low, and the programs often fail. Yet, we all know of companies that have made significant advances in their operations using these same quality management practices. Why do a few succeed while many fail? History has shown that the companies that successfully carry out quality management programs have two things in common: 1) Strong leadership committed to the success of the program. 2) A comprehensive plan for carrying out and maintaining the program. Stated another way -the reason many companies fail is the lack of committed leaders and inadequate planning. It is ironic that the title of the Wall Street Journal article is "The Best Laid Plans."

Jan 1, 1994

By T. Acton

The Zarafshan/Newmont Joint Venture is currently operating in the Republic of Uzbekistan producing in excess of 400,000 oz. of gold per year from low grade oxide ore stockpiles adjacent to the Muruntau open pit gold mine located in the Kyzylkum desert of central Uzbekistan. Four stage crushing and screening produces a final product for heap leaching, Merrill-Crowe processing, and local refining for International market export. The Zarafshan/Newmont Joint Venture is the first major commercial project of its kind in the former Soviet Union to be successfully negotiated, engineered & constructed, and placed into continuous operation,

Jan 1, 1997

By Wendell E. Bearce

At the, Crescent Valley Mine of the Hanna Coal Company, several 10,000 ton unit trains of 41" x 0 strip coal are loaded per week during the lake season. This is accomplished without the use of any accumulation of prepared coal. A large raw coal pile is built up during the winter months adjacent to two truck dump bins. This is added to whenever trucks are coming in from the pits and trains are not being loaded. During the loading of trains, trucks from several pits dump into the truck hoppers and coal is also dozed in from the pile. At a rate up to 3200 tons per hour this coal is screened, the plus 6" hand picked, the plus 4" crushed, and' all weighed and sampled as it goes directly to railroad cars being handled on two tracks by car retarders. With such an arrangement it is possible to exercise some control over coal quality, if it can be assessed rapidly. For instance, if the moisture rises to a level where it seems probable the BTU per pound will be reduced to the point where the contract calls for penalties, the trucks from, the wettest pit may be stopped, more or less coal may be moved in from the stockpile, or other measures taken to assure that the average BTU of the trainload will be satisfactory.

Jan 1, 1967

By P. Moyo, S. Dixon, R. Norcross

The separation and recovery of copper from cyanide solution has been investigated since the early 1900s. The precipitation of copper using sulfide ion was patented in 1911 by Williamson, published by Leaver & Woolf of the USBM in 1931 and Cyanamid in 1960s. The current practice of sulfide precipitation is used in various processes such as “SART" for cyanide regeneration and copper recovery. The precipitation of copper sulfide requires the pH of the clear solution to be in the range of 4-6. The precipitated copper sulfide can be sold to smelters. Alternatively, copper cyanide can be precipitated from clear solutions in the pH range of 2-3. However, selling copper cyanide is challenging because of its cyanide content. Past work has focused on the use of boiling sulfuric acid to convert copper cyanide to copper sulfate as published by Seracini in 1991. This paper describes a simple process to convert copper cyanide to copper oxide using sodium hydroxide at ambient temperatures. The cuprite can be sold to smelters or used as a feed to an electrowinning circuit to produce copper cathodes. The process provides an effective method to recover copper from cyanide solutions with a lower capital requirement.

Mar 2, 2022