Search Documents

By Walter C. Labys

This paper reports on recent modeling efforts to analyze the eastern U.S. steam coal market with a cross-sectional econometric as well as a quadratic programming approach. The background to coal modeling is examined first. The particular aspect of the steam coal market to be modeled are then presented and the corresponding coal model described. Both empirical results and rigorous mathematic pertubation analysis are presented. Conclusions are then drawn regarding potential modeling applications in the policy area.

Jan 1, 1979

By Jiang Su, Michal Uhrin

"The use of composite linings, consisting of permanent sprayed primary and secondary linings with a sandwiched spray applied waterproofing membrane is expected to improve efficiency and reduce lining thickness, but it also brings complex primary-secondary lining interaction. This issue is further complicated by the uncertainty regarding the long-term behavior and parameters of the sprayed concrete–sprayed membrane interface.This paper aims to address this issue by presentation of a series of numerical analyses of a typical shallow SCL tunnel in soft ground with a range of design assumptions on the interface behavior: (1) compression only; (2) compression and tension; and (3) compression, tension, and shear.The results demonstrate that the assumed interface behavior has a significant impact on the primary-secondary lining interactions. A design approach of ignoring the tension and shear bond at the interface may not be conservative particularly for serviceability. This paper explains the rationale behind these conclusions and discusses the implications for design.INTRODUCTIONSprayed Concrete Tunnel Lining SystemsSprayed concrete linings (SCL) have been used in conventional tunneling for decades. However, details of SCL systems may differ to a large extent depending on ground conditions and specific tunneling methodologies.In hard rock conditions, for example, drill and blast excavation is typically supported by rock bolts and sprayed concrete (NGI 2014). Such tunnels are usually designed fully drained and the above-mentioned support elements considered permanent without the need for a further inner liner. Therefore, there is no structural interaction between separate lining shells to consider.In conventional tunneling in the European Alps, a double shell lining is typically utilized, consisting of an outer (primary) sprayed concrete lining and an inner (secondary) cast-in-place concrete lining, separated by a waterproofing system. The primary lining normally includes rock bolts and may include other support elements. The waterproofing system is usually based on a plastic membrane and a geotextile fleece. The tunnel may be designed fully or partially drained or fully undrained. Although there are two structural lining shells interacting, investigation of such interaction is generally irrelevant to designers because the primary lining is considered only temporary (fully sacrificial in the long term). An overview of reasons for this assumption is given, for example, by Lemke (2014). The secondary lining is designed to resist all foreseeable loads on the tunnel. The primary lining may, in reality, interact structurally with the secondary lining during the life span of the tunnel. However, since the secondary lining design must cover all possible (extreme) scenarios, investigation of such interaction does not bring any value to the design."

Jan 1, 2016

By R. Asmatulu

According to Darcy?s law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By B. A. Slaker, T. Miller

"An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys, to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in) was measured by the extensometers, photogrammetric reconstructions, and laser scanner over a 6-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls was significantly lessened. INTRODUCTION Limestone formations in the United States can be subject to relatively high horizontal stresses due to the presence of tectonic loading of the strata. Horizontal stresses have a documented history of causing stability issues in underground limestone mines. Kuhnhein and Ramer (2004) discussed the influence of horizontal stress on complex ground control interactions associated with limestone pillar design and mine layouts. Esterhuizen et al. (2008) documented roof damage observations associated with high horizontal stresses such has roof guttering, beam instability, oval-shaped falls, and failure propagations. There have also been a number of documented case histories of horizontal stress causing unexpected roof and pillar failures at shallow depths (Stacey and Yathavan, 2003). To the knowledge of the authors, there has only been one well-documented case of floor failure causing stability issues in an underground limestone mine. Murphy et al. (2015) documented the role that a weak, moisture-sensitive floor had in the development of a massive roof collapse. For this paper, the study site neighbored, and was in the same general geology of, the site in Murphy et al. (2015). However, the weak, moisture-sensitive floor was not present for the current study. The current study site has experienced significant floor instabilities caused by high horizontal stresses. The instability area was monitored using two different methods to determine if the floor failure would eventually propagate into roof or pillar failure. The objective of this paper is to analyze displacement monitoring measurements from string potentiometers and remote sensing techniques in an area experiencing active movement. Based on the measurement trends and observed damage from inside of the mine, the presumed failure process will be discussed."

Jan 1, 2017

By C. M. Marquardt

The materials handling systems in the large concentrating plants have required the employment of a considerable number of workmen, many of whom had very little to do except to act as watchmen to avoid bad spills at belt junctions and to operate tripper cars, shuttle belts, etc. Much time also was spent in watching bins to make sure they were properly filled. Approximately four and one-half years ago the author, Yin coopera¬tion with the engineering and supervisory personnel of The Anaconda Company at Anaconda, Montana, began to give this problem serious consideration. Prior to this the author had developed, at the request of The Anaconda Company, a transistorized resistance-sensitive probe relay system for detecting the level of ore in bins. With this system cables or chains were suspended from insulators above the bins and were of suitable length to determine the elevation of the ore in the bins.

Jan 1, 1962

By P. I. Prescott

Ground calcium carbonate (GCC) is used in the paper, plastics, paint, rubber, caulks, and sealants industries. The favorable properties of GCC include high whiteness and brightness, low hardness, and outstanding rheology in water systems. The quality of calcitic GCC ores, which include chalk, limestone, and marble, is dependent on calcite purity and the nature and quantity of ancillary minerals. Wet and dry grinding is used in the manufacture of GCC. Ore processed by optical sorting, flotation, and/or particle size classification has higher brightness and lower abrasion. GCC markets are a function of the product's properties, purity, and cost.

Jan 1, 1995

By Katherine Hynard, Colin Eustace

Development quarterly mine plans is generally time-consuming and requires consideration for many operational constraints and competing objectives. With lengthy turnaround times, there is often limited opportunity to adjust the quarterly plan details to account for differences between actual state of the mine operation at the time of execution and expected state at the time that the plan was developed. Actual mining task completion times can vary significantly from the expected task completion times, due to many factors. In the absence of revision to account for differences between the planned and actual state, resource allocations and mining sequences, embodied in the quarterly mine plan may no longer be the best approach at the time of execution to achieve an efficient mining operation. Simulation and optimisation tools can be used to support rapid refinements for development and execution of weekly mine plans. When initialized with an operations data feed to establish the actual state of the mine operation, optimisation models can be used to facilitate both automation and revision of the quarterly plan to produce a weekly or daily plan for execution. This approach can remove much of the manual burden of revision if the existing quarterly plan no longer represents the best approach to meeting production objectives. Following initialisation with mining actuals, simulation models can provide a representation of the range of likely mine operations outcomes. The models can be used to accelerate the planning process by providing visibility of future performance and identifying likely operational issues. They can also be used to test the robustness of the plan with respect to performance variability and response to disturbances. Following identification of issues, simulation models can also be used for evaluating mitigation measures, through automated testing of alternative plans. Integration of mine data feeds with simulation and optimisation tools enables automated optimal responses to variations between the quarterly mine plan and actuals to be tested prior to release of and execution plan and implementation. The use of simulation and optimisation in weekly mine planning will be discussed in this paper with reference to surface mining examples.

Jun 25, 2023

By G. Blackwell

In the 1980's the Canadian surface mining industry was confronted by declining competitiveness in the face of low cost foreign producers and alternative materials. Low metal prices undermined profits for many mining companies. Restructuring, rationalization, capacity reduction, technology transfer, as well as favourable currency rates and higher commodity prices, helped revitalize the industry by the close of the decade. Now in the 1990's, however, the need to improve competitiveness for profitability has re-emerged in greater intensity. In the current climate it is considered that there are three strategies available to industry to ensure profitability: continued rationalization and restructuring; optimization of operating practice; and technology development and transfer.

Jan 1, 1993

By J. Yao

Synthetic indium-bearing zinc ferrite (IBZF) was mechanically activated by a tumbling mill. Subsequently, the behavior and kinetics of leaching zinc and indium from the initial IBZF and activated IBZF in sulfuric acid solution were investigated. The results demonstrate that the tumbling ball milling enhances the leaching reactivity of IBZF and increases the zinc and indium extractions. The reaction temperature and H2SO4 concentration have an important effect on leaching zinc and indium from the initial IBZF and activated IBZF. The kinetic model -ln(1-x) = kt was used to describe the kinetics of leaching zinc and indium from the initial IBZF and activated IBZF and to calculate the kinetic parameters. The tumbling ball milling causes a decrease in activation energy and reaction order, which indicates that the dissolution of IBZF after mechanical activation by a tumbling mill becomes less sensitive to temperature and H2SO4 concentration. For the zinc leaching, the activation energy decreases from 73.9 to 70.3 kJ/mol and the reaction order decreases from 0.72 to 0.70. For indium leaching, the activation energy decreases from 78.1 to 73.5 kJ/mol and the reaction order decreases from 0.82 to 0.69. It is found that the dissolution rates of the initial IBZF and activated IBZF are controlled by surface chemical reactions.

By E. A. Devuyst, G. Robbins

A unique process for removing cyanide and base metal complexes from industrial waste streams was patented by G.J. Borberly et al. (1984). The process uses SO2 (liquid or gas, or solutions of sulfite salts, or from burning elemental sulfur), plus air that is dispersed in the effluent using a well agitated vessel. Acid produced in the oxidation reactions is neutralized with lime at a controlled pH generally in the range 7 to 10. The reaction requires the presence of soluble copper as a catalyst which can be supplemented by copper sulfate if necessary. The process can be applied to the detoxification of gold and silver mining waste streams, such as carbon-in-pulp (CIP) tailing pulps, barren solution bleeds, pond waters and heap leach rinse solutions and also to plating shops wastewaters. The SO.jAir process has substantial advantages over two of the main alternative methods of cyanide destruction, namely alkaline chlorination and hydrogen peroxide. Alkaline chlorination is highly penalized in terms of reagent consumption. Chlorine is a strong oxidant reacting with species other than cyanide present in the effluent such as thiocyanate and sulfides. Furthermore alkaline chlorination is an incomplete detoxification process. Iron cyanide is not removed and the potential for harmful by-products species exist. Consequently final effluents may be subject to additional treatment in order to comply with regulatory demands.

Jan 1, 1991

By R. J. Roman

Controlled and uniform distribution of the leach solution to a heap is of primary importance to achieving the desired rate of metal recovery and PLS grade from the heap. The step used to engineer the irrigation system are the same whether drips, wobblers or sprinklers are to be used. The mining rate, leach cycle time and heap height influence the heap cell size which along with the irrigation method selected controls the design of the irrigation system. The steps in the design procedure are explained as are the advantages and disadvantages of each irrigation method.

Jan 1, 1996

By R. Q. Honaker

Although the fundamental principles of hindered bed classifiers are relatively simple, the complex interactions between the operating parameters provide a degree of difficulty that hinders the ability for on-line plant optimization. Thus, a dynamic population balance model was developed for determining the hindered settling velocity of particles varying in density and size. The steady-state results of the model include partition curves as a function of particle size and density as well as metallurgical data. A statistical comparison of the simulation results with those obtained from industrial units reveal a high level of accuracy with adjusted R2 values greater than 0.95.

Jan 1, 1999

By Rolf N. Schulz

The recently completed major modifications and additions to Reserve Mining Company's taconite concentrating process incorporate a totally new control system. Design of the new control scheme is centered on reliability, versatility, centralization, and optimization. The design objectives were achieved through a distributed control system based on a network of independent field located micro-processor based control systems connected to a central control room. Operation of each micro-processor can be interrogated and modified from the central control room by the operator or by either of two computer systems. The two computer systems handle logging, alarming, specialized sequenced controls, and complex process optimization routines.

Jan 1, 1980

By T. Karlkvist, H. R. Kota, F. Andreas, B. I. Pålsson

"Separation of different calcium minerals have long been an interesting and challenging problem. In this investigation calcium mineral separation is examined by: microflotation, zeta potential measurement and adsorption, using novel collectors having two functional groups instead of one. In theory, by varying the distance between the functional groups, it could be possible to preferentially target one calcium mineral by matching the spatial distance between the sites on the mineral surface. In this investigation two new surfactants have been tested to estimate their ability to float apatite and/or calcite. Preliminary findings show that an increase in distance between the functional groups favors one mineral over the other, and this might be due to differences in the mineral surface structure. INTRODUCTION Apatite is a strategically important mineral which has both great value for industrial use as a precursor to phosphoric acid; and in the agricultural industry as an important source of phosphorous in fertilizers. This has led both the European Union and the United States to recognize it as an important resource for the future. Currently there is no lack of apatite in the world, but it is important to develop the beneficiation to ensure future supply. A common problem in apatite flotation is the selectivity towards calcite, which it is commonly associated with. Although calcite is an important industrial mineral its abundance makes it not usually worth to extract from apatite ores unless it is easy to separate1,2. Both apatite and calcite are semi soluble minerals with calcium as one of their constituents. The most common way to separate apatite and calcite is to use flotation. A process that involves making the mineral particles to extract from the system hydrophobic by adsorbing a collector on the mineral surface. One way to study collector adsorption on a mineral surface is by zeta potential measurements. The zeta potential is the charge at a slip plane a short distance from the surface. By measuring the zeta potential with and without the presence of collector it is possible to investigate if the collector is present at the surface or not, a change is indicative of collector adsorption. The zeta potential of fluorite, apatite and calcite without collector can be seen in Figure 1. The small difference in zeta potential between apatite and calcite shows the similarity in their surface properties and gives an indication of their separation difficulty. One additional problem with semi soluble minerals is their tendency to slightly dissolve in the pulp and thereby change the ionic composition of the solution. This makes separation and research problematic as the freed ions may readsorb on the mineral surface and interfere with the collector adsorption on the mineral surfaces3–5."

Jan 1, 2016

By Dean Treweek, Anthony Harding

"Creating stable, safe, constructible and cost effective support to openings in segmental linings is often an important component of successful delivery of a tunnel project. The many constraints on successful implementation include operational, spatial, geotechnical, structural, and constructability. Failure to address these adequately can lead to significant impacts on cost, schedule, and safety. With reference to past project experiences, this paper provides a guide to the most commonly deployed solutions and their pros and cons to help designers quickly identify the most appropriate solutions for a particular project, or act as a starting point for developing new and/or project specific solutions. It highlights the challenges that designers and contractors must address together for successful support of tunnel openings, and the constraints that arise. It then describes the common structural forms of support, and how each form can mitigate the constraints, allowing an effective opening support system to be implemented. INTRODUCTION While only a small portion of the total excavated volume of a typical tunnel, cross passages are often one of the most complex elements of a bored tunnel to construct. Cross passages in soft ground typically involve ground improvement, groundwater control, and multiple temporary support measures to ensure safe construction in ground that has been overstressed due to the construction of the running tunnels. Permanent lining construction requires careful detailing of waterproofing and reinforcement to support both long term ground and water loads and support the broken out rings of the main lining. While there is not a great deal of literature specific to cross passage construction, the main issues are discussed in some detail by Lawrence and Taylor (2011). However, the temporary support of the running tunnel segmental linings during cross passage construction is not always given the attention it deserves. The authors have been unable to find much literature on the design of such systems, much less the considerations that have led to a particular solution. Lawrence and Taylor only mention two potential methods of support. It may be easy to dismiss the opening support as an inconsequential item, but selection of the wrong support type can have significant impacts on both cost and schedule."

Jan 1, 2016

By R. L. Bleifuss

The object of this study was to evaluate the oxidized taconites of the western Mesabi iron range and to establish a correlation between the various basic taconite types and their concentratability. This study was made at the Mines Experiment Station of the University of Minnesota under the sponsorship of the Great Northern Railway Company. The initial work included a study of the original mineralogical and stratigraphic facies of the fresh taconite and traced the oxidation and leaching patterns developed during the conversion of this material to oxidized taconite. Subsequent studies have extended this work to include the semi- taconites and also the wash and heavy media ore types widely developed in the area. Each basic, original mineralogical facies or taconite type produces during alteration an equivalent secondary oxidized facies which has a unique mineralogical composition and texture. These control the concentratability of the oxidized taconites. Actually the influence of the original mineralogical composition of the iron formation extends even further and determines whether the most likely product of oxidation and leaching will be a wash ore or a heavy media ore and even to the direct shipping ores where the ratio of hematite to goethite is largely determined by the original taconite type.

Jan 1, 1964

By R. Musu, J. A. E. Bell

P.T. Inco has constructed a smelter to produce 45 000 tonnes (49 500 tons) of nickel per year as a nickel matte from the lateritic ores of Sulawesi, Indonesia. The facilities include mines, five screening stations, two dryers, three novel reduction kilns, three electric furnaces, three top blown rotary converters, and associated infrastructure of port, towns and a hydroelectric generating station. The screening stations and converters are unique in the industry. The problems encountered in the construction and operation of this complex facility in remote Indonesia are described.

Jan 1, 1979

By Madan M. Singh

Increasingly, geotechnical data are being collected for various types of coal development projects. In many cases, a specific design concern is addressed. However, many data collection programs are not intended to immediately support mine design activities or to resolve a specific concern. The following discussion describes some current geotechnical approaches in mine planning, development of reserves, and peripheral activities. Types of Data Collection Programs Geotechnical data collection is increasingly becoming a part of standard coal exploration programs, performed along with stratigraphic evaluations and coal quality tests. The aims of such programs vary. The purpose of the exploration may be to fill out the portfolio on a block of reserves that is to be sold, leased, or held for potential future development. In such a case, a generic suite of geotechnical data are collected. The resulting engineering reports may touch on the more well known mining problems of the area, but detail may be lacking. The geotechnical data are mostly intended to enhance the saleability of the package. Mine design alternatives are generally not addressed.

Jan 1, 1985

By J. A. Organiscak

Enclosed cab filtration systems are typically used on mobile mining equipment to reduce miners? exposure to airborne dusts and diesel particulates generated during mining operations. Various filter configurationscan be used within the heating, ventilation and air conditioning (HVAC) systems of cabs to remove the airborne contaminants. The air cleaning performance of cab filtration systems is highly dependent on the efficiency of the air filters, the number of filters used and their placement within the HVAC system. This paper shows how to mathematically model cab filtration systems and illustrates a methodology for developing other cab filtration system design models. Node diagrams of several filtration system circuits are illustrated with their mathematical models at steady state airflow and concentration conditions. Laboratory and field data are presented to demonstrate the validity and utility of modeling enclosed cab air cleaning performance. The paper concludes that incorporating multiple filters throughout the HVAC system improves the air cleaning performance and robustness of the cab filtration system design

By C. P. Blair

In discussing so-called "volume rates" for the movement of coal, I start from one basic premise: That it is the job of the railroads to devise rates which will move the traffic, while at the same time assuring a fair return on their investment. No matter how reasonable and nondiscriminatory freight rates may be, if they fail to attract and hold traffic to the rails, they are utterly useless - both to the carriers and the shipping public. And it will be my purpose here to show that under certain circumstances the use of volume rates by the railroads enables them. to hold traffic which would otherwise be lost, and to avoid needless dissipation of revenues, Properly employed, volume rates should benefit both the coal industry and the railroads, I do not, however, advocate the discarding of the carload as the basic rate-making unit. Far from it. Sound operating reasons dictate the making of rates based on car- loads, and the tradition of carload rates has a firm foundation in railroad operating costs, many of which vary directly with cars handled. In short, the carload was, Is and, in my opinion, will continue to be the basis for most rail rates on coal, as well as on other commodities. But change is an inevitable result of progress, and we should not be so bound by tradition that we are unwilling to try novel methods of ate making, should the circumstances require, The modern rate maker must, now and then, run the risk of being called an iconoclast if he is to keep up with the times. As T will point out, volume rates were for many years rejected by both the Interstate Commerce Commission and the railroads, But now both the Commission and the carriers have come to recognize that under proper circumstances and conditions volume rates are a powerful and effective tool.

Jan 1, 1959