Search Documents

By Jinke Li, Fenghua Wang

"While coal fueling China's economic growth it has already been causing severe pollution and amounts of CO2 emission. How to make deep reductions in carbon emission is not only a huge challenge for the greatest consumer of coal, but also a revolution for China’s coal industry. The paper explores how to shrink CO2 emissions during the lifetime of coal. The paper points out that increase of coal mine efficiency and productivity, green mining, utilization of coal mine methane and environment-friendly disposal of coal gangue can reduce CO2 during coal mining; coal preparation and coal by wire can decrease CO2 during coal preparation and transportation; improving combustion efficiency, CO2 capture and storage (CCS) and coal transformation can lessen CO2 during coal utilization. The paper also points out that Circular Economy Park is a practical way to develop a low carbon economy for coal industry. An econometric model for total coal industry and each sector are constructed to measure carbon emissions based on CO2 equivalent emissions, then with detailed calculations, based on potential greenhouse-gas emission's reduction, a most likely low carbon roadmap of China's coal industry is depicted with scenario analysis method.Introduction Global warming poses a profound threat to humanity and the natural world and is one of the most serious challenges humankind has ever faced. According to the 2007 Fourth Assessment Report by the Intergovernmental Panel on Climate Change (IPCC), global surface temperature increased 273.89 ± 273.33K during the 20th century (IPCC 2007). Increasing concentrations of greenhouse gases have caused most of the observed temperature increase since the middle of the 20th century (United States National Academy of Sciences 2008), and CO2 is the most important cause of global warming. In 2005, CO2 contributed 76% of global greenhouse gas emissions, CH4 contributed approximately 16%, N2O contributed approximately 6% and the combined F-gases contributed approximately 2% (IEA 2010). Among the many human activities that produce greenhouse gases, energy use is by far the largest source of emissions. Since 1870, CO2 emissions from fuel combustion have risen exponentially (IEA 2009). Of the three types of fossil fuels - coal, natural gas and petroleum - coal constituted only a quarter of the world total primary energy consumption in 2007. The situation is even more critical in China than in the rest of the world, as energy-intensive industrial production is growing rapidly, and large coal reserves exist in combination with limited reserves of other energy sources. The development and production of the coal industry provide stability in China's economic growth. There are more than 7000 coal enterprises in China; the coal enterprises are the main contributor to China's ""economic miracle""."

Jan 1, 2017

"The 33rd annual American Mining Hall of Fame Awards Banquet and Fundraiser sponsored by the Mining Foundation of the Southwest (MFSW) will be held at the JW Marriott Tucson Starr Pass Resort & Spa on Saturday, Dec. 5, 2015. Each year, one living Hall of Fame inductee, two Medal of Merit recipients, several honorees from Mining’s Past, an Industry Partnership Award and a Special Citation are recognized for their respective contributions to the mining industry.Conrad E. Huss, cofounder of M3 Engineering & Technology Corp. located in Tucson, AZ, will be honored as the 2015 Hall of Fame Inductee and will serve as the keynote speaker at the awards banquet. Huss has served his company as chairman of the board for its entire 30 years and guided M3 to become a full discipline firm. Now M3 offers complete project execution through engineering, procurement and construction management procedure and has become a major engineer of large observatories around the world. The company now has more than 1,000 employees with offices in Arizona, North Carolina, Mexico, Argentina and is incorporated in Guatemala, Peru and Canada.The Medal of Merit will be awarded to Charles Michael (Mick) Lownds, founder of his eponymous consulting firm in Salt Lake City, UT, for his 42 years in commercial explosives following tenure at Sasol and at Orica. Originally from South Africa, Lownds immigrated to the United States in 1998 and has made significant advancement on electronic initiation systems. Lownds has published numerous technical papers, is an inventor with 12 awarded United States patents and was also the recipient of the President’s Award from the International Society of Explosives Engineers in 2000.Medal of Merit for young professionals will be awarded to Fiorella Giana, Freeport- McMoRan Inc.’s (FCX) mine manager at Bagdad. Born in Buenos Aires, Argentina, Giana left the small cattle farm where she was raised in 2001 to pursue higher education in the United States. For the past decade at FCX, as a result of her extraordinary combination of technical skill, leadership and commitment to excellence, she has been given positions of progressively greater responsibility from an entry level engineer to senior mine engineer, to chief engineer and now as mine manager, a position rarely held by woman."

Jan 1, 2015

By L. T. Larson

Had the blank on the Abstract form been sufficiently spacious a more appropriate title for this paper would be: Neogene Tectonism, Magmatic Activity and Hydrothermal Precious Metal Mineralization in Anatolian Turkey; an Analog with the Basin and Range Province of the Western U.S.? Like the alternative title no thing in Turkey is simple. Its history is long and convolute; its culture fascinating; its metallogeny diverse and its geology very complex. This paper will focus only on the geology of western' Anatolia and the precious metal potential of this third of Turkey. The argument is in the article but to save the reader time and suspense I'll put my conclusions up front- the potential is great and the possibilities exciting.

Jan 1, 1989

By Dapeng Zhang, Brij Moudgil, Shibo Zheng, Chunhui Feng, Wenyi Song, Wending Xiao, Patrick Zhang

The separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. More than 50 percent of the phosphate reserve in Florida contains too much dolomite to process using current industry practice. The current way of producing phosphoric acid requires less than one percent MgO in the phosphate concentrate as the feed material. The Florida Industrial and Phosphate Research (FIPR) Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered three feasible options. Option I entails three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand, which could reduce MgO content in the final concentrate by 20 to 40 percent. Option II involves the crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9 percent MgO at about 87 percent P2O5 recovery. Option III is a gravity separation technique using an innovative separation jig, and its full potential remains to be demonstrated.

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

Over the past 15 years, roof fall rates have decreased by two-thirds in U.S. coal mines and by even more in regions where the roof is weakest. This remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present an empirical design methodology that uses real-world data to quantify the basic roof-support concepts that have been successful in the United States. A new computer package, called Analysis of Mine Roof Support (AMRS), implements the design methodology.

By Ryan Marsters, Adam Pring

The Rawah Ditch is a mountainous water supply diversion which supplies Larimer County, Colorado with water since 1903. The ditch includes two historic tunnels excavated by drill and blast through a gneissic rock buttress. Both rock tunnels were failing with annual convergence. After a snowshoe-accessed eld investigation, nite element modeling, and an alternatives analysis, a diameter DE pipe was inserted within each tunnel and the annulus lled. The proect was implemented in an Alternative Delivery contract lasting ve months from eld investigation through procurement and construction.

Jun 23, 2024

By A. Ferreira Morgado

The sodium smectitic clays (bentonites), have more industrial applications in that class of mineral, a driving force to obtain this mineral. In Brazil, there are several occurrences of smectitic clays, unfortunately they are polycationic, with a distribution of several exchangeable cations, where the cation sodium occurs in minor quantity. In this work, the original polycationic smectitic clay was firstly proper characterized and then treated with sodium carbonate obtaining homoionic sodium smectitic clay. The rheological tests in the optimized sodium smectitic clay showed good results for drilling fluids, typical of a sodium bentonite ones.

Jan 1, 1999

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

Polysaccharides have been used as depressants for naturally hydrophobic talc in the flotation of base metal sulfide ores, precious metal sulfide ores and platinum group metal (PGM) sulfide ores. The results of this surface chemistry study confirm guar gum as a preferred polysaccharide for talc depression in the flotation of these ores. In addition to the practical application of the research results, the surface chemistry results are of academic significance, providing further information to understand how polysaccharide depressants function in these complex sulfide flotation systems.

By H. I. Meyer

The mine is a large open-pit copper mine located near Tucson, AZ. Mining operations involve shovels digging at relatively fixed locations and haul trucks moving the muck to a primary ore crusher, a primary waste crusher, and directly to waste dumps. The total investment in shovels and trucks is some $100 million. Fig. l is a schematic drawing of the operation. A static method of truck assignment is used; i.e., each driver is given one particular shovel to serve until reassigned by the dispatcher. A dynamic system is one where trucks are reassigned after each trip. The problem is to compute a near optimum assignment of trucks for efficient operation.

Jan 1, 1979

By P. G. Martin

"As the speed of business has continued to increase over the last decade, the focus on real-time control of the performance of both stationary and mobile assets has become an increasing priority. Traditionally the maintenance team has been focused on the management of the availability of assets while the operations team has been focused on the throughput of those same assets. Typically operations and maintenance teams worked almost independently in spite of the fact that they were both working with the same assets. Part of the problem has been their traditional performance measures which have often been diametrically opposed. Recent advancements in the area of real-time performance measures and decision support have helped to drive higher levels of collaboration between operations and maintenance leading to real-time asset performance control and higher levels of business performance. This paper will explore the forces driving the need for changes, present an effective approach to the definition of the most appropriate business performance measures, and examine the effectiveness of contextualized real-time decision support resulting in asset performance control. TRADITIONAL APPROACHES TO ASSET PERFORMANCE MANAGEMENT In most industrial operations the phrase asset performance management is synonymous with maintenance of the industrial assets. This is the way industry has viewed asset management and asset performance management for decades. This is a very limited perspective that is serving to constrain the profitability of industrial operations. As industrial organizations began to form following the Industrial Revolution, the complexity of the operations forced an organizational design based on specialization. No single person could understand all of the aspects of an industrialized operation. This was particularly true at the plant floor level where the operation and maintenance of the industrial equipment required very different skillsets and training. To accommodate the vast differences most industrial organizations set up operations teams to run the equipment and maintenance teams to keep the equipment available to the operation. Both teams were dealing with the same industrial equipment but from very different perspectives and with very different performance measures. Typically the operations team was measured on maximizing the output of the equipment – or throughput. On the other hand the maintenance team was measured on the uptime – or availability of the equipment."

Jan 1, 2015

By M. P. Valoski

In the United States, the occurrence of underground mine fires/explosions continue to decrease; however, they pose great danger to the miners and any subsequent mine rescue teams and/or fire brigades. Tragically, 19 coal miners lost their lives in 2006 at fires or explosions. Fires/explosions can devastate a mine and cause its permanent closure. It is vitally important to obtain accurate information on the gas content (concentration and composition) of the mine atmosphere after the event so that appropriate action can be instituted to rescue any trapped miners while not exposing the mine rescue teams to unnecessary hazards. Additionally, the fire fighting techniques (spraying water, sealing, etc.) will be dictated by the gas content. Finally, the gas content will determine when it is safe to recover the mine. The gas content of the air can be determined using detector tubes, handheld instruments, portable instruments, or gas chromatographs. No single instrument is suitable for all analyses. Each type of instrument has its advantages and disadvantages. This paper discusses these attributes.

Jan 1, 2010

By S. R. Clark

"INTRODUCTION Of all the natural resources being taxed by the needs of the modern world, perhaps the most important is the continually expanding demand for water resources. As water becomes scarcer, and increasingly important, new technologies are needed to find innovative ways to preserve this precious resource. In Chile, for example, the mining industry is investing billions of dollars to build desalination plants and pipelines; bringing ocean water as far as 200 kilometers inland to meet their demand and maintain operations. It is a full-blown crisis for that nation and a top priority for their government and economy. It has been reported that world water consumption will increase by 40 percent in the next 10 years, representing nearly exponential growth. In the U.S., as more and more communities continue to be built, more drain on the current water infrastructure is created. For 25 percent of people and operations that rely on water from aquifers, this source is being consumed at a rate that will create significant problems meeting the demand in as few as two generations.1 A PROACTIVE APPROACH When it comes to controlling dust at your operation, whether a landfill, a transfer station, a haul road or another ancillary area, what are the options? We know watering is not the answer, but at the same time, we need to prevent dust from flying to ensure a safe environment and keep our skies clear of pollution, for both regulatory requirements and neighbors. Creating a Dust Mitigation Program instead of looking to buy the first dust control product off the shelf is a first step to conserve water and, at the same time, maintain the operational demands and environmental standards for a given site. The program concept is straightforward enough. However, the process of effectively constructing and executing a program is quite involved. When undertaking a program, each manager needs to work with their team and their partners/vendors in analyzing the following elements: 1. Site Expectations—It is important to understand how to balance your internal standards with your regulatory requirements, as well as how to keep your neighbors satisfied. 2. Site Aggregate—Variations in native soil, such as clay content or gravel levels, greatly affect the approach that will yield the highest results. 3. Climate—Relative humidity and seasonal variations are critical to achieving predictable results through product choice, application frequency and timing. 4. Daily Traffic—The type and frequency of traffic is an essential variable for site management. 5. Environmental Responsibilities—If you have additional, specifically defined responsibilities, the approach to your site may vary. 6. Budget—While efficiency is the goal of any program, some sites will have more stringent restrictions than others. 7. Current Usage Rates—Document and understand where you’re starting from, both with water, supporting products, and maintenance so that effective measurement of results is possible."

Jan 1, 2018

By Christophe Bragard, Jason Choi, William H. Hansmire

This case history provides a physical benchmark of tunneling technology progress comparing an old hand-mined tunnel to a modern 20-ft-diameter EPB TBM that mined in the same ground. This rare opportunity to see how tunnels were constructed many years ago occurred when an old 10-ft-diameter storm drain tunnel in the way of os Angeles subway construction was demolished and replaced with obas berglass pipe. Steel rib and lagging initial support was exposed showing solid-sawn 2" × 12" × 48" redwood lagging. This paper documents the as-built old tunnel, how it was successfully replaced, and some lessons learned.

Jun 23, 2024

By Adrianus Halim, Jenni Hooli, Bartłomiej Skawina, Fredrik Sundqvist

Transitioning from diesel-powered loading and hauling machinery to battery-electric vehicles (BEVs) responds to the need for deepening underground mines as regulations become tighter. When using BEVs, exhaust gases and diesel particulate matter (DPM) emissions can be eliminated, and the energy required for the machines is used more effectively. Unlike their diesel counterparts, which are refueled, BEV loading and hauling machines — specifically, load haul dump (LHD) machines — can use battery swapping. This brings additional aspects to the operation that need to be considered, which have not yet been studied extensively. This study used discrete event simulation (DES) to analyze how the different numbers of BEV LHDs affect queueing and productivity when using different numbers of batteries and different swapping times in an underground block cave mine. The results identified the formation of working groups, where the machines swapped their batteries concurrently within each group, and their relation to the queueing time. Additionally, the minimum number of batteries per machine was identified to maximize productivity while minimizing queueing time. This study demonstrates DES as a powerful tool to assess and analyze conceptual systems and identify their underlying structures, which can enhance the deployment of BEV LHDs in underground block cave mine operations.

Apr 1, 2025

By Sotiris N. Kamenopoulos, Zach Agioutantis

Rare earth elements (REEs) are considered critical minerals for the industrial and defense sectors. In 2018, the U.S. Department of the Interior presented the final list of critical minerals that are vital to the U.S. economy and defense [1], which included REEs among other mineral commodities. REEs are not rare, despite their name, but economically viable deposits of REEs can be found only in certain geographical areas, and the political and social conditions characterizing these areas may not always be in favor of mining operations. Mining operations may be placed in great operational and financial risk if operations are planned in such areas. Erroneous decisions by decision makers may lead to a chain of events that can completely shut down a mining project. 

By Jayson Ripke, Peter Amelunxen, Brandon Akerstrom, Fernanda Solís

It is commonly known in the industry that one of the key challenges for a greenfield project, such as Capstone Copper’s Santo Domingo project, is the obtention of samples for metallurgical testing and subsequent plant design. To face this challenge, the Santo Domingo project completed 169,692 meters of drilling. The material collected has been used for a variety of analysis including the economic recovery of iron, which contributes significant economic value to the Santo Domingo business case. Composite and variability samples, covering the main geological units considered in the life of mine (LOM) plan, were selected for bench and pilot scale testwork. Davis Tube Tests, small scale Low Intensity Magnetic Separation (LIMS) tests and a pilot utilizing a 48 in (1.2 m), diameter magnetic separation drum were completed. The testwork demonstrated that the Santo Domingo ore could achieve iron concentrate grades of 65% Fe - suitable for blast furnace, and 67% Fe - suitable for Direct Reduction, primarily by concentration of magnetite. The outcomes of this work have informed the iron concentrator plant design and scale up.

Feb 1, 2025

By Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyoming, was completed on July 30, 1976. During the experiment production reached 0.32 Mm 3/d (12 Mft3/d) of 6.9 MJ/m3 gas (175 Btu/ft 3 ). Approximately 6100 tonne (6700 ton) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, cold gas - thermal efficiencies of 76 to 89 percent, and overall process efficiencies of 65 to 74 percent were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-1974.

Jan 1, 1977

By B. Alegria

The depressing effects of different inorganic chemicals on the flotation of pyrite have been investigated in this study. The results of the flotation tests indicate that pyrite can be depressed by oxidizing as well as reducing agents under controlled conditions of pH and reagent dosage. Oxidizing reagents such as potassium chromate and potassium dichromate were found to cause complete depression of pyrite in the acidic pH range. These effects are similar to those obtained in the pyrite-cyanide system. A less stable oxidant, potassium permanganate, inhibited the flotation of pyrite at a concentration as low as 0.1 mol/L at all pH values, Addition of reducing chemicals such as ferrous chloride or manganous sulphate to the flotation of pyrite were found to produce depressing effects depending on the additive concentration and pH of the solution.

Jan 1, 1982

By Ying Lu, Jeffrey C. Johnson, Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Energy dissipation and fragmentation of rock is of interest for mine-to-mill operations in order to understand breakage and to minimize energy consumption during blasting at the mine site, and comminution at the processing plant. In this regard, high velocity impact breakage of long granite cores, called bars, has been studied with instrumented strain gages to follow the energy dissipation gradient along the bar length resulting from the strain waves generated by impact. As a result of high velocity impact, three zones have been identified (fragmentation, fracture, and elastic) and these three zones have been characterized in 3D using X-ray tomography. The fragmentation zones of the granite bars were studied in detail to describe the particle size distribution and the particle shape characteristics. Finally, the experimental energy dissipation for the fragmentation zone was found to be in close agreement with the expected energy calculated from the Bond work equation, if the anisotropic granite particles are defined by length rather than by sieve size.

By R. Venugopal, V. K. Saxena, A. K. Mukherjee

"Coal, iron and manganese ore samples were exposed to different ultrasonic intensities of 250, 300 and 350 W/L for five minutes and to an ultrosonic intensity of 270 W/L for different time durations of 3, 5 and 7 minutes. The ultrasonically treated samples showed reductions in D80 particle diameters of 6 percent for the coal samples, 5.95 percent for the iron ore samples and 35.63 percent for the manganese ore samples during grinding. The ultrasonic treatment was also observed to assist in reducing ash content in the coal product by 8 percent and to reduce manganese losses in rejects by about 5 percent. Ultrasonic treatment was concluded to be capable of assisting in the comminution of friable ores more prominently than the hard and porous materials.IntroductionComminution is an important unit operation in the mineral-processing, cement-making, powergeneration and pharmaceutical industries. But most of the milling technologies are considered to be energy inefficient, with less energy consumed in real size reduction and most of the energy consumed in the machine. This is more critical for the mineralprocessing industry because of the growing need to exploit lower-grade ore bodies and process rejects (Blazy et al., 1994; U.S. Department of Energy, 2005). Low-grade ores require crushing and grinding to liberate the valuable minerals, which are further separated from gangues by various beneficiation methods such as gravity separation, flotation and leaching. Various studies have been carried out to minimize energy consumption during milling by developing pretreatment methods that can initiate new fractures or improve the fracture density in materials before comminution. These studies were mainly focused on chemical additives; thermal, ultrasonic and microwave treatments; and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman, Briggs and Kojovic, 1997; Gaete-Garreton, Vargas-Hermandez and Velasquez-Lambert, 2000; Kumar et al., 2010; Wang, Shi and Manlapig., 2011, Singh et al., 2012).The fragmentation effect of ultrasonic fields in solids has been investigated since the 1950s, and Gärtner was probably the first researcher who attempted it (Gaete-Garreton, Vargas- Hermandez and Velasquez-Lambert, 2000). Sound waves can propagate in solids in the form of longitudinal waves, shear waves and surface waves, and in thin materials as plate waves.In surfaces, fractures and interfaces, various types of elliptical or complex vibrations of the particles make other waves possible. During ultrasonic-vibration treatment, cavitation bubbles nucleate, grow and collapse, generating microjets, whose impacts on the particles initiate microcracks. The ultrasonic waves can enhance the nucleation, growth and coalescence of flaws, caused by tensile or shear stress. The mechanisms operating in the materials and inducing these stresses have been identified as spall and compression-induced tensile microcracks, nucleating at preexisting flaws. These mechanisms are driven by the shock wave and cavitation effects in the surrounding fluid (Chen, Huang and Shih, 2003)"

Jan 1, 2016