Search Documents

By Yuan Le, Dominic Reda, Vojtech Ernst Gall, Kurt Zeidler, Tomasz Kecerski

High Speed 2 (HS2) mandated that Building Information Modelling (BIM) processes be implemented during design and construction. Gall Zeidler Consultants (GZ) was responsible for developing the BIM Models for the portals, tunnels, and cross passages of the of the 16 km-long Chiltern twin-bore Tunnel. In addition, GZ developed the GBR for the Chiltern Tunnels and incorporated the relevant information into the Project’s BIM framework. This paper presents the implemented BIM framework, describes the modelling approach, and discusses the advantages and challenges of implementing BIM, particularly how BIM improved interface coordination and how BIM was used in feasibility assessments of different construction options.

Jun 13, 2023

By K. H. Lee

The rate of beryllium dissolution from a low-grade ore was studied in sulfuric acid solutions. The effect of stirring speed, sulfuric acid concentration, particle size and temperature on the rate of dissolution of beryllium was established. The results of the study showed that the dissolution rate is independent of stirring speed within the range of 250-1000 rpm but depends on 1/2 power of the sulfuric acid concentration. The dissolution rate increases exponentially with decrease in particle size and the maximum attainable rate of extraction with respect to particle size is 6.6 x 10 mol dm min. The apparent activation energy (^E) for the dissolution reaction is 54.4 kJ/mol (13.0 kcal/mol). Based on this magnitude of the activation energy, it is concluded that a surface chemical reaction is the rate limiting step for the temperature range (70° -100°C) investigated.

Jan 1, 1988

By E. F. Klein, R. L. Eacret

Introduction In contrast to the general type of crushing mechanism in which the crushing surfaces alternately approach and withdraw from each other, described earlier in this section, and continuous-pressure break¬ers such as rolls and roller mills that will be described in a later chapter, impact crushers load by striking pieces of rock while in free fall and hurling them at high speed against stationary surfaces. Because the impact crusher depends for its effectiveness upon high velocity, wear is greater than in the slower-moving jaw and cone¬type wear parts, and for this reason its use is strictly limited to rela¬tively soft, friable, and sticky rocks that are characteristic of many nonmetallic mineral deposits. A few of these are phosphates, lime¬stone, barite, clay, asbestos rock, and coal. However, several examples of their use on soft lead-zinc and precious metal ores have been known. Although the use of impact crushers is expanding today into the range of ores containing as much as 15-18% silica, Taggart16 set the practical limit at 5%, and in the 1940s and 1950s several installa¬tions in the US and western Europe exceeded the limits of economical maintenance and were quickly superseded by the slower-moving, con¬ventional crushers. A rock that tends to be plastic or bouncy in a jaw or gyratory crusher when the force is applied slowly to reach ultimate strength, may become brittle with rapid loading and thus increase the effective¬ness of the applied forces. For this reason it is to be expected that as the quality of hammers, grates, plates, and cages improves with advances in steel technology, the use of high-speed crushers of this kind will increase. Terminology Modern usage differentiates between the impactor and the hammer mill, the former relying primarily on the impact of hammers (fixed or free-swinging) and secondarily upon pieces striking one another or steel surfaces; the hammer mill relies on both the centrifugal impact force of free-swinging hammers and the attrition and shear action between these hammers and well-placed grates suspended at the bot¬tom just below the hammer circle. The hammer mill, because of its grate discharge, restricts discharge of oversize rock to the grate open¬ing, while at the same time providing a trap for removal of tramp iron or other uncrushables. The impactor discharges free, so generally works with a screen to control product sizes. The question of terminology, impactor vs, hammer mill, creates difficulties because the similarities appear to outweigh the differences by far; if one were to list the similarities in order of importance and then the differences, he would be forced to conclude that they would best be dealt with as a single kind of crusher. Taggart16 gave it four names and added "as it is variously known," but it must be remembered that in 1945 the machine was nearly exclusively of the flailing-hammer type, while today the fixed-hammer rotor is also com¬mon. In this chapter the terms impactor and hammer mill will be used where they seem to apply. It is perhaps unfortunate that this terminology is being confused with rock breaking at the mine, usually with hand-held tools, e.g., the article "High-Energy Impact Rockbreaking" by Grantmyre and Hawkes, CIM Bulletin, August 1975. General Description Impact breakers, impact crushers, and hammer mills accomplish material breaking and reduction primarily through impact action of the material with fixed or free-swinging hammers revolving about a central rotor. The material to be crushed enters through an opening at the top or top side known as the "feed opening" or "hopper opening" and falls into the path of rotation (hammer circle) of the hammers. Initial breakage is accomplished in midair by collision of the dropping feed material with high-speed hammers. The second stage of breakage occurs when the pieces hit plates or breaker bars which line the crusher boxlike frame. Hammer mills rely further on a shearing and attrition action between free-swinging hammers and grid bars or grates at the crusher bottom which restrict discharge of oversize material until it is broken sufficiently to pass through the grid opening. The term hammer is used in reference to the piece which strikes the material, whether it is fixed on the rotor or free-swinging. It

Jan 1, 1985

By Nathaniel Wollman

About nine years ago the President's Materials Policy Co commission under the chairmanship of William Paley released its report entitled "Resources for Freedom." Not long ago the Senate Select Committee on National Water Resources under the chairmanship of Senator Kerr released a study entitled Water Supply and Demand. Both reports contained projections of future water user the report for 1975, and the Select Committee print for 1980 and 2000, It is my task to compare the two reports. In the initial letter from Mr. Kazmann arranging for thus session he suggested that I present "a critical evaluation of the Paley Report's section on water ?ten years later,? which might include a comparison of predicted and actual water-use rates and would spotlight the assumptions which lead to errors in the predictions , . ." It is possible to compare the results of both studies, and it possible to explain art of the differences that can be found between them. The remainder must remain shrouded in doubt, since the Paley Report did not give all details of the methods used in estimating the com¬ponents of water use.

Jan 1, 1961

"The 34th International Conference on Ground Control in Mining (ICGCM) was held July 28–30 at the Lakeview Golf Resort and Spa in Morgantown, WV. Ground control experts have gathered at this location since 1981 to share ideas and successes for improving designs and technologies to enhance the stability of surface and underground mining operations. Ground control is important to all mining operations but is particularly crucial to underground mining to ensure miner safety and operational viability.The year’s event had 240 registered attendees with 20 pecent of that attendance being from the mining industry. A remarkable number of industry representatives attended given the challenges currently faced by the mining industry. A true testament to the value of the conference, the performance of Tom Barczak and Steve Tadolini as co-chairs and the drawing power of the many exceptional speakers that have attended the annual event for many years.The conference operates under the direction of a board of directors with the cooperation, wisdom and assistance of a large organizing committee. Visit the conference website, www.icgcm.conferenceacademy.com, to view the membership of the board and the committee and to access previously published papers."

Jan 1, 2015

By Robert C. Ellman

Lignite and subbituminous coals are utilized essentially as mined without beneficiation. Most of the present production is used to generate electric power and the major problem in this use is ash deposition on fireside surfaces. The preparation at existing mines involves principally crushing and screening operations. Blending of production from different locations within the mine is practiced in several mines to control ash composition. Drying and oil treatment for freezeproofing, of lignite are used to a limited extent during winter. Future processing may involve both washing and drying operations to alter ash composition by ion exchange and upgrade the low-rank fuels to higher heating values. Research has been initiated to determine the feasibility of such processing.

Jan 1, 1969

By Nick Tessitore, Ryan Marsters, Alex Warren, Dylan Fawaz

The West Gates Deicing Industrial Waste Pond Expansion project at Denver International Airport seeks to expand utilities to accommodate additional terminal gates. The project includes six tunnel crossings beneath taxiways and runways with lengths ranging from 239 to 2,025 linear feet. Excavation methods include shielded tunnel boring machines and steerable auger boring. Designed initial support includes liner plate, steel ribs and lagging, steel casing, and Fiberglass Reinforced Pipe and ranges in size from 24" to 132". This paper will discuss challenges associated with the overall layout and design of the project, including contingencies to protect critical infrastructure. In addition, a construction update is provided.

Jun 23, 2024

By Douglas M. Smith

The town of Tayoltita, Durango is located at the bottom of the 2000 m. deep Rio Piaxtla canyon on the axis of the rugged Sierra Madre Occidental mountain range. Throughout most of the year access to the town is restricted to travel by mule or STOL aircraft. Silver and gold have been produced from epithermal veins in the north side of the canyon since 1757. During the last seventy-three years more than 4,588,000 kg. of silver and 76,322 kg. of gold have been produced from approximately 6,000,000 metric tons of ore. The Tayoltita mine is developed within a fault block bounded by normal faults which strike north-northwest and have opposing dips. A thickness of at least 1300 meters of late Cretaceous or early Tertiary volcanic rocks is exposed in the mine. These range in composition from andesite to rhyolite. Andesite predominates in the upper 750 meters of the section. The volcanic rocks were passively intruded by quartz-monzonite and andesite stocks during middle (?) Tertiary time. Mineralization spatially and temporally (?) related to the stocks occurs along the east boundary fault and in intersecting footwall fissures which strike east-west and northeast. Ore was deposited over a vertical range of up to 600 m. prior to tilting of the volcanic rocks 35 to 45° to the east. With few exceptions, the ore bodies are found within the lower 400 to 500 m. of the andesite. Argentite (acanthite), stromeyerite, jalpaite, electrum and native silver are the principal ore minerals. They occur in gangue composed of one or more of the following: quartz, calcite, bustamite, adularia, chlorite, and albite. Base-metal sulfides make up less than 1.5 percent by weight of the ore.

Jan 1, 1974

By Stanley R. Riggs

The rocks exposed in the phosphate district are of Neogene age and consist of clayey quartz and phosphorite sands overlying phosphatic dolomite. The Bone Valley Formation is redefined as a marine phosphorite containing primary phosphorite and abundant terrigenous sediments. It contains a Middle Miocene vertebrate and invertebrate fauna and conformably overlies the Hawthorn Formation containing similar invertebrate fauna. A new, unnamed formation, with Pliocene and Pleistocene fauna and containing reworked phosphorite, overlies the Bone Valley disconformably. Its phosphorite is derived from the subjacent Bone Valley by post-Middle Miocene erosion and deposition in stream channels and marginal marine environments. The Bone Valley contains two main types of primary marine phosphorite. Orthocbemical phosphorite, a direct precipitate of microcrystalline phosphorite (microsphorite), occurs as a cement or binder in thin beds. Allochemical phosphorite consists of clastic phosphorite particles that were originally formed as microsphorite on another part of the shelf. Microsphorite was deposited in a very shallow open marine environment which had an abnormally high phosphorous content caused by upwelling currents. The mechanism of deposition is still in doubt, but organisms probably were a major factor. Soon after deposition, microsphorite was indurated, periodically torn up, and the resulting fragments transported and deposited elsewhere on the shelf. These processes account for a great portion of the clastic phosphorite in the Miocene deposits of Florida. The primary fossil skeletal material is of minor importance.

Jan 1, 1965

By Steven M. Puricelli

In recent times, smelter off gases treatment plants have become more efficient and environmentally friendly. Where in the past it was acceptable to process only high strength, treatable furnace gases, new smelters must now treat primary gases and abate dust and SO2 from secondary gases: Processing smelter gases can present some interesting challenges. Some equipment can see varying concentrations of sulfuric acid, up to the boiling point, with a periodic table of contaminates thrown in for good measure. Treating weaker secondary gases have, in the past, been cost prohibitive. Nowadays, new technology, like physical absorption or catalytic carbon, show promise for economically treating low strength secondary gases. Modem smelters do a much better job of treating the SO2 laden gases generated by the smelting process but significant challenges remain.

Jan 1, 1998

By P. A. Korpi

In March of 1978 the first set of Angular Spiral Liners utilized in grate discharge ball mills for wet grinding was put into service in the San Flanuel Concentrator of Flagma Copper Company. The use of these liners has decreased grinding media consumption by 19.2% and grinding energy consumption by 15.8%. In addition a 1.1% increase in grinding throughput is being realized through the use of the system. This paper describes the Angular Spiral Lining System and reviews the test program at the San Manuel Arizona Concentrator. Operating parameters are discussed in addition to the current testing program to futher optimize the system.

Jan 1, 1982

By Ernest L. Ohle

Since the first recorded discovery of lead in southeast Missouri near Fredericktown about 1720, knowledge of the deposits has advanced in spurts as a result of outlying discoveries: 1864 Bonne Terre 1890 Flat River, Desloge, Leadwood 1948 Indian Creek 1955 Viburnum The original discoveries at Bonne Terre consisted of residual galena in clay, similar to that in the previous finds at Fredericktown. Occurrences in solid dolomite were not noted until mining of the clay pits exposed the walls of the weathered depressions. The St. Joseph Lead Co. had been established to conduct the operations and it was J. Wyman Jones, first president of St. Joe, who at that time brought about the first of the technological advances that were to occur in the district. He proposed use of the newly invented diamond drill to explore the bedrock showings, after observing the machines in the Vermont Marble Belt.

Jan 1, 1991

By J. David Lowell

The discovery of the Kalamazoo (Arizona) ore body was a comedy of errors and coincidences and luck -as most discoveries probably are. The story began in early 1965 when Quintana Petroleum decided to diversify from petroleum into minerals and decided to do this by the route of minerals exploration. Quintana Petroleum is owned by the Cullen family of Houston and has Geen successful over the years in discovering oilfields. In 1965, the president and general manager was Corbin J. Robertson, son-in-law of Harry Cullen, founder of the company and a famous Texas wildcatter. But, in 1965, Quintana's financial advisors suggested that the company go into several mineral commodities, including copper, with Tucson, AZ, as the jumping-off point for copper exploration, and with a geological consultant (me) as the point man. The stage was now set! (See Fig. 1, location map of the San Manuel District, Arizona.)

Jan 1, 1991

By K. N. Han

The leaching behavior of palladium in ammoniacal solutions was investigated by using the rotating-disk technique in an autoclave. The study included the effects of rotation speed, temperature, oxygen pressure, composition of ammoniacal solutions and catalysts on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in terms of the thermodynamics and a kinetic model. Even though the Eh-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was very slow at temperatures below 100 °C but was significantly improved at higher temperatures. It was also found that the rotating speed of the palladium disk had no effect on the leaching rate. The apparent activation energy was found to he 69.7 kJ/mole. Based on the results obtained, it was concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1999

By Richard F. Roethe

Surface coal mining productivity in the U.S. and Illinois has shown a general declining trend since 1969. The U.S. Department of Energy conducted an analysis in 1980 of the causes of declining productivity in different states. This paper presents a detailed analysis of changes in overall productivity and productivity in different functions such as overburden preparation, overburden stripping, reclamation, coal handling, etc. during the period 1970-1982. Statistical analysys techniques including multiple regression were utilized in the study.

Jan 1, 1983

By Wallace N. Thomas

The present interest in large diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a seven to eight thousand horsepower mill will cost from 1350 thousand to $600 thousand which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functions -- establishing a realistic compromise between cost and performance.

Jan 1, 1969

By AMIR EHSAN KIANFAR, Moritz Ziegler, TOBIAS HARTMANN, ELISABETH CLAUSEN

Accurate positioning information is a central step in the process of increasing automation and digitalization in the mining industry. Underground mine environments are prime examples for GNSS-denied environments that pose several additional challenges for the employed indoor positioning system (IPS). This work presents an ultra-wideband (UWB)- based system specifically tailored for underground mine environments. Initially, the UWB technology is reviewed and basic concepts of IPS are explained. Both software and hardware are described in detail, including positioning algorithms, electrical circuitry and the mining-compatible enclosure. Finally, the results from field tests in an underground mine are presented and positioning performance and the influence of dilution of precision (DOP) on positioning results are empirically evaluated. The results show that the localization errors are mostly below 1 m. Individual zones of high localization errors are suspected to be caused by noise interference. Significant DOP influence due to the mining drift geometry can be confirmed. The system shows promising localization results for different mining applications, while influences negatively impacting the accuracy are presented as items for future research.

Jan 1, 2024

By W. L. O?Connell

[Patent Issue No. Date Issued To Subject 386,504 July 24, G. Sweanor The separation of quartz from a 1588 metal with a liquid such as CS2 or CHC13 under water by introducing mixture into water layer. Quartz will stay in water layer while metal sinks through organic.]

Jan 1, 1963

By Earl M. Frizzell

Investigation of mined land characteristics, evaluation of irrigation systems and evaluations by the mining industry determined that irrigation is a feasible method for aiding the revegetation of coal mined lands in the western arid and semi-arid regions (Sherman, et al. 1980). The various regions studied displayed a commonality of characteristics which enables, independent of the site or region, the recommendation of solid-set irrigation. Irrigation should be supplemental by complimenting natural precipitation and should be implemented on a temporary basis. For germination, the vegetation requires application of small amounts of water in a gentle, frequent, and timely manner. For the establishment phase of growth, moisture should be applied and stored in the soil either through pre-irrigation or deep irrigation.

Jan 1, 1985

By Taner Aydogmus

The A$29 billion Chevron-operated Wheatstone Project is one of Australia’s largest resource projects. Located at Ashburton North, 12 kilometers west of Onslow in Western Australia, the project will consist of two Liquefied Natural Gas (LNG) trains with a combined capacity of 8.9 million tons per annum and a domestic gas plant. The LNG Plant will serve the offshore gas fields, which are situated some 250 km off the coast of Onslow in Western Australia. Once operational and on-stream, the Wheatstone Project will contribute to Australia becoming the world’s second largest exporter of LNG. For crossing the environmentally sensitive shore area, a micro-tunnel with an internal diameter of 2 m and approx. 1,242 m in length has been constructed by means of the pipe-jacking method. The micro-tunnel will accommodate a 1.1 m diameter pipeline (trunkline) to deliver gas from the offshore fields LNG Plant. The Wheatstone shore crossing design involves a number of unique challenges owing to its coastal location, where the alignment crosses through a shore area and terminates in a marine environment. This paper provides an overview of the Wheatstone Shore Crossing Project, presents the key features, and discusses the main aspects of the micro-tunneling design.

Jun 13, 2021