Search Documents

By CADEN VITTI, Barbara J. Arnold

Mine tailings, the byproduct of mining and mineral processing, are increasingly mass-produced as a result of increased demand for metals and minerals as well as the advancement in technology that allows for the exploitation of lower-grade ores. Lower grades can increase the volume of tailings that may contain new gangue minerals that should be evaluated for the presence of critical minerals and other valuable metals. The practice of reprocessing, while relatively new, is crucial to reducing environmental damages, obtaining valuable critical minerals from waste, and contributing to more sustainable repurposing and disposal methods. With the increase in tailings dam failures in recent years, there is a large motivating factor in remining and removing the potential hazard to benefit the safety of potentially impacted communities. In analyzing the perspectives of various domestic and international studies, this literature review will determine the feasibility of reprocessing and reutilizing mine tailings waste for a more sustainable future while exploring current practices that have benefitted ecosystems and communities.

By Weijie Wei, Jinwang Zhang, Shengli Yang

In longwall top-coal caving (LTCC) mining with an inclined seam, the recovery rate is low and equipment stability is poor due to the unbalanced top-coal drawing process. To address these problems, this paper proposes the dynamic group caving method (DGCM), whose basic premise is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Using particle flow code (PFC), the caving mechanism of top coal under DGCM was investigated. The results are of significance to realize high efficiency and precise caving in LTCC mining with an inclined seam.

By S. A. Saki, J. F. Brune

"INTRODUCTION Longwall coal mining leaves large areas where the coal has been made removed and the roof rock strata collapse, forming a zone of broken rock rubble called the gob. Figure 1 shows a typical longwall gob area along with the gate roads. The ventilation pattern for progressively sealed longwall panels follows a simple “U” pattern where fresh air is coursed inby to the headgate, flows along the face and exhausts through the outby tailgate as shown in figure 1(a). An important variation of this pattern is the back return (BR) arrangement where the exhaust air from the face is drawn inby and around the nearest open cross cut before it turns in the outby direction towards the exhaust fan. Figure 1(b) illustrates the use of back return. This arrangement moves the point of low pressure from the tailgate corner up to 60 m inby and thus maintains fresh air in the tailgate region that could otherwise be contaminated with gob air.The gob area may contain remnants of unmined coal or parts of overlying coal beds that continue to release methane, eventually filling the gob area with methane in concentrations far above the explosive range of about 4.5 to 15%. Many gob areas must be equipped with gob ventilation boreholes (GVBs) to extract methane, and GVBs often exhaust methane at concentrations from 50% to 90% (Saki, 2016). Due to oxidation processes occurring in the gob, the oxygen content is reduced to a low level, with nitrogen and CO2 making up the major remaining components of the gob atmosphere. FORMATION OF EXPLOSIVE GAS ZONES IN GOBS Since the longwall face area is ventilated with fresh air below 1% methane and the face and gob areas are not separated, an explosive fringe will form where the methane content lies within the explosive range and oxygen content remains above 12%. Figure 2 shows a typical development of such an EGZ. This figure is based on a computational fluid dynamics (CFD) model developed by CSM researchers to analyze gas concentrations and flow patterns in longwall mining. Figure 2(a) shows the formation of EGZ in the gob with a U type ventilation scheme, where EGZ lies right behind the shields in the tailgate corner. Figure 2(b) shows the formation of EGZ in the gob combining U type ventilation scheme with BR, where EGZ is pushed away from the face deep into the gob. The CFD modeling parameters and boundary conditions have been verified with field data from two cooperating, active longwall mines (see Worrall 2012, Marts 2015, Gilmore 2015 and Saki 2016). Other mine geometries, methane inflow rates and gob permeability distributions can be modeled to establish representative gob atmospheric conditions. Two GVBs were operating in the model, extracting 0.165 m3/sec each. The methane in the working areas and returns was kept below 1%. Methane flowing into the model from a rider coal bed above the mined seam was at the rate of 0.55 m3/sec."

Jan 1, 2017

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

Rutile ore is an important resource for the production of titanium products, and flotation is an efficient method to enrich rutile from its deposits. Motivated by strong commercial demand for titanium metal and alloys, substantial efforts have been made to improve the flotation efficiency of rutile. Styryl phosphonic acid (SPA) and salicyl hydroxamic acid (SHA) are commonly used as collectors for rutile flotation, and lead (Pb) ions can be used as activators for rutile flotation with SPA or SHA. Xanthates have a price advantage over SPA and SHA for the flotation of sulfides as SPA and SHA prices are higher than xanthate prices. In this work, we found that when rutile is activated by lead ions, amyl xanthate is an efficient collector for rutile flotation at pH 8. A slightly basic slurry can be readily obtained. Moreover, the price of amyl xanthate is lower than that of SPA or SHA. In this regard, this flotation strategy has the potential to be used in industry. Furthermore, the adsorption features of amyl xanthate on the Pb-activated rutile surface was investigated by experimental methods, which provides insight into the role of lead ions in rutile flotation.

By Roger L. Hulette

Mt. Newman Mining Co. is now completing an expansion program, begun even before initial construction was complete, which will result in facilities with the ability to ship over 30 million tons of iron ore per year by early 1973. Confidence in such rapid future growth was evidenced by careful planning for the future expansion of those facilities provided for initial operation of the project which first shipped ore on 1 April 1969. Ore sales contracts totaling more than 300 million tons have been negotiated, thus justifying the optimism which led the joint venturers to provide over $200 million in initial investment and a like amount in capital required to finance the continuing expansion program. Members of the Mt. Newman Joint Venture are: Amax Iron Ore Corporation - 25% (a subsidiary of American Metals Climax) Pilbara Iron Ltd. - 30% (a subsidiary of Colonial Sugar Refining) Dampier Mining Ltd. - 30% (a subsidiary of Broken Hill Proprietary) Seltrust Iron Ore Ltd. - 5% (a subsidiary of Selection Trust Ltd. of London) ? Mitsui C. Itoh Iron Ore Pty. Ltd. - 10% Mt. Newman Mining Co. Pty. Ltd. manages the project on behalf of the five companies which make up the joint venture.

Jan 1, 1972

By A. Moergeli, Philip Sander, John Reilly

"SUMMARY While the basic elements of risk management, including probability, consequences, risk registers, mitigation measures, etc., are now well understood, the process to include correlation, dependencies and linkage of risks and risk scenarios is less well defined and not well understood. To perform accurate and complete risk analysis and risk management, it is necessary to include correlation, dependencies and linkage between risk events, as well as risks that may occur multiple times. In this way, owners and contractors can more accurately determine risk-based costs, risk impacts and risk mitigation strategies. This paper will outline methods to deal with correlation, dependencies and linkage and will consider risks that may occur multiple times. Practical result comparisons – with or without these elements – will be presented. INTRODUCTION We believe the reader is familiar with basic concepts of risk, risk management and mitigation and the use of probabilistic cost-risk processes versus deterministic ones (Reilly et al. 2015; Sander et al. 2015). The probabilistic approach, compared to the simpler and more common deterministic approach (unit prices times unit costs plus a contingency), offers more useful information with respect to the range of probable cost as well as cost “drivers” and better quantifies the effects of risks, opportunities and variability – which improves understanding, leading to a better potential for profit (or loss) for contractors and added value for owners. In this context, a valid and sufficient quantification of correlation, dependencies and linkage of risk events, plus the impact of risks that may occur multiple times, is essential. Components of Cost Estimates – Base Cost, Risks and Other Uncertainties The components of cost that need to be correctly addressed in an estimate include (Moergeli et al. 2015): •,Base costs – the costs that will result if “all goes according to plan” (Reilly 2004) •,Risk costs – the resulting costs of threat and opportunity events, if they should occur •,Escalation costs – costs resulting from normally expected inflation with variability •,Other uncertain costs – costs that result from other events, normally external to the project team’s control, which may include unanticipated events, politically related changes and “black swan” events (Talib 2007)"

Jan 1, 2016

By J. F. T. Agapito

Experience at Energy West Mines in the Wasatch Plateau Coal Field, Utah, has shown that longwall face bursts occur mostly near the tailgate when extracting the third adjacent longwall in a panel section where depths exceed 610 m (2000 ft). It is believed that this is due to a combination of cover depth and side abutment stresses created by the widening of a pressure arch formed by interlocking and bridging of large blocks of" very competent strata. The 60-m-thick (200 ft) Castlegate Sandstone probably plays a key role in pressure arching. This paper presents a back-analysis of the location and magnitude of the stresses associated with face bursts that occurred when mining the 7th Right Longwall at the Deer Creek Mine. Improvement of these conditions may be achieved by widening the longwalls to attain critical subsidence width sooner while mining the second long-wall, and to reduce stresses at the face. Wider longwall faces, however, increase the chance of sandstone channel interception often associated with bursts. Satisfactory mitigation of face bursts beyond cover depths of 610 to 670 m (2000 to 2200 ft) may be difficult without using destressing techniques. The hydraulic fracturing/liquid infusion technique seems to offer the best possibilities for application in longwall mining.

Jan 1, 1997

By Zohreh Kazemi Motlagh, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Five-element style deposits are unusual hydrothermal systems that are typically characterized by a nickel-cobalt-arsenic- silver-bismuth metal assemblage. This mineralization is often represented by abundant native silver, arsenic, or bismuth, and followed by nickel, cobalt, and iron arsenides (skutterudite, safflorite, nickeline, rammelsbergite, and lollingite). The Black Hawk district in Grant County, New Mexico is one of the few examples of this mineralization style in the United States. Despite the differences in formation temperature, depth of emplacement, and host rocks between five-element style deposits worldwide, there are commonalities in mineralogy, ore texture, and composition. A detailed exploration of the native metal and arsenide phases will be performed to compare ore forming fluids between systems and the effects on styles of mineralization and paragenesis, as well as to aid in broader classification of the deposit style. Mineralogy and mineral relationships of the Black Hawk District and other five-element deposits worldwide will be characterized by reflected light petrography, scanning electron microscopy, X-ray diffraction, and electron microprobe analysis. Mineralogical phase diagrams will be generated to better understand the driving processes and evolution of the systems through native metal and arsenide precipitation.

Feb 1, 2024

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means of controlling gases and dust. In order to study longwall ventilation in a controlled environment, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers built a unique physical model called the longwall instrumented aerodynamic model (LIAM). The LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel. It has an 8.94 by 4.88 m (29 by 16 ft) footprint with a simulated face length of 220 m (720 ft) in full scale. LIAM is built with critical details of the face, gob and mining machinery, and scaled to preserve the physical and dynamic similitude. This paper discusses the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By William Gleason

"In a time that seems to be dominated with nothing but bad news coming from the mining industry, there is a success story that has been quietly happening in Southwestern Wyoming for more than 60 years, and it is one that is likely to continue for many decades to come.Beneath the wind swept high desert plains of Sweetwater County, WY, about 32 km (20 miles) west of Green River, lies the Green River Basin where five companies, including Tata Chemicals North America (TCNA), are mining the world’s largest known deposit of trona and, in turn, are collectively producing 15.3 Mt/a (17 million stpy) of soda ash.“We have a long-term growth story that has been, and will continue to be a steady earner for many years to come,” said J. Martin Keighley, managing director of TCNA who has been in charge of the mine, formerly known as General Chemical Industrial Products Inc., for Tata Chemicals for about three years.According to the U.S. Bureau of Land Management (BLM), Keighley is safe with his prediction of future success. The BLM estimates that there are enough reserves in the Green River Basin to last another 2,000 years. Currently, four trona beds in the Green River Basin are being mined and in all, there are 25 major trona beds that occur within the Wilkins Peak Member of the Upper Eocene Age Green River Formation. The trona deposit as a whole covers about 2,500 km2 (1,000 sq miles) within the Green River Basin.And imagine, this economic mainstay in the region was discovered accidently.Prior to 1948, soda ash, the salable commodity that comes from trona and is used in a host of products including glass and detergent, was produced synthetically. In 1938, an oil and gas exploration team working in the Green River Basin came away with a find that would change the soda ash industry and the physical and employment landscape of southwestern Wyoming forever. Within 10 years, the communities of Green River and Rock Springs, which were built largely on the back of coal mining and railroads, had another commodity beneath their feet."

Jul 1, 2016

By Steven J. Schatzel, Kayode M. Ajayi, Marcia M. Harris, Zoheir Khademian

Predicting rockmass permeability is critical in evaluating various engineering designs, including estimating gas inflow to a longwall mine in the case of a hypothetical breach in the gas well. This study conducted field permeability measurements to validate a geomechanical model capable of predicting rockmass permeability during longwall mining. A series of slug permeability tests were conducted in an active mine in Pennsylvania. A model of the mine was constructed in 3DEC numerical modeling software, and permeabilities were calculated. The modeling results agreed well with the pre- and post-mining permeability measurements, showing the applicability of this tool to evaluate gas well stability near mine workings.

Feb 1, 2024

By Vladimir Nikolić, Alex Doll

The Bond ball mill grindability test is one of the most common metrics used in the mining industry for ore hardness measurements. The test is an important part of the Bond work index methodology for designing and measuring the efficiency of mineral grinding circuits. In spite of being called “Bond’s Law,” the work index equations are not a law of nature; but rather an empirically measured regression of a large data set collected by the Allis- Chalmers corporation in the period between 1930 and 1952. As a regression, it is valid within a specific “calibration space,” and great care is required when deviating the test procedures or observing results that are outside of that calibration space. This paper is a collected summary of other works by the Authors that describe feed sizes, product sizes, quality control checks, and other information about interpreting the test and using its results. Examples of adjustments that are sometimes required when using the test are: changing the test product (P80), and coping with a feed that is too fine to apply the “proper” feed preparation steps (such as is sometimes observed from HPGR or SAGDesign product testing). Related metrics, like the Morrell Mib value and Levin B value will be discussed, along with recommendations for their use on design projects. The intended audience is any user of laboratory work index test data.

Feb 1, 2024

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor --will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Jan 1, 1997

By Gregory M. Rumbaugh, Todd R. Kostecki, Christopher Mark

The paper examines five massive pillar collapses in underground stone mines in the eastern United States from 2015 to 2021. These collapses caused significant airblasts, surface subsidence, and damage to mine infrastructure. The study identifies factors contributing to pillar collapses, such as slender pillars with width-to-height ratios of 0.8 or less, and proposes a framework for evaluating and mitigating collapse risks.

Nov 1, 2023

By Hamed Khodadadi, Hamid Ghadiri

The ball mill grinding circuit has widespread application in mining, metallurgy, chemistry, pharmacy and research. It faces some challenges because a grinding circuit is a multivariable system in which high interaction between loops, variation of system parameters with time, and time delays are problems. In this study, a fuzzy logic self-tuning proportional–integral–derivative (FLST-PID) controller based on an improved disturbance observer is designed for control of ball mill grinding circuits. It is combined with an improved disturbance observer (IDOB) to eliminate system interaction, attenuate internal and external disturbances and compensate the effect of system uncertainty on the performance of the ball mill grinding circuit.

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

For the first time, surface subsidence prediction theory was used to investigate roof movement around longwall face mining in a steeply dipping coal seam. A physical simulation experiment was conducted to quantitatively study the roof migration patterns, the gob materials, and the characteristics of bed separation and compression caused by mining two adjacent panels to gain a better understanding of ground control issues in multipanel mining in steeply dipping seam. This approach provides an in-depth analysis of the movement of the roof. Compared to movement observation of survey point using total station, the Photogrammetry Analysis for Physical Modeling of Mine Subsidence Program (PAPMMSP) method is easier to perform, faster and yields the much higher accuracy required for scale physical modeling. It is also a more effective observation method for underground-mining physical simulation experiments.

By Yi Luo, Hua Jiang

A roof bolting drilling operation in an underground coal mine can expose the operator to a high concentration of respirable coal and crystalline silica dusts (smaller than 10 µm). Overexposure of high-level quartz dust for a roof bolter operator can lead to the development of silicosis in as little as three years [1]. This study proposes a drilling control algorithm for the bolt hole drilling process. This algorithm can be integrated into a current drilling control system on the roof bolter machinery and is expected to reduce the generation of respirable dust while enhancing the energy efficiency of the roof bolter machine. In addition, the drilling efficiency and bit condition can be evaluated while drilling based on the real-time feedback parameters. This capability enables the algorithm to ensure the drilling is performed under a relatively high energy efficiency with less respirable dust generation and to avoid drilling with an excessively worn bit that can cause bit clogging or steel buckling failure.

By KAGAN BENZESIK, OMUR CAN ODABAS, SELCUK KAN, Onuralp Yucel

In this study, domestic molybdenum disulfide (MoS2) concentrate was roasted in a chamber furnace and then in a rotary kiln. The behavior of the roasting process was examined in both furnaces, and which type of furnace is more advantageous to use in mass production was investigated. It is theoretically possible to roast in a chamber furnace, but a major problem was observed when the amount of concentrate was increased in the chamber-furnace experiments. The problem was solved by using a rotary kiln. This study improves the understanding of the roasting of  MoS2 concentrate and presents a different perspective to the industry, showing that rotary kilns can also be used for roasting.

By David A. Greenhut

The Kubota surface melting system has been under development since 1975. It has found commercial application on the melting of municipal sludge, and ash from solid waste. The melted product has physical properties allowing its use as a substitute for aggregate in cement and asphaltic construction. This paper describes the surface melting system, its current use and anticipated future use.

Jan 1, 1991

By D. Yokom, T. Katsabanis, E. Tremblay

"The mining industry has always faced the problems of replacing retired mining professionals, retaining their knowledge, continuously developing the skills of local talent and employing under-represented groups. In expansionary scenarios the industry faces the additional challenge of increasing available talent. New talent has traditionally come from current mining programs; however, these programs have been declining in numbers, and those that remain face challenges such as fluctuating enrollments, and reduced budgets. Queen’s University and Northern College have partnered to develop an innovative new program that offers online mining education to engineering technologists seeking to upgrade their skills and obtain a Bachelor’s degree. The high quality, flexible curriculum, offered online, includes a wide range of learning activities that promote interaction (student-to-student, student-to-instructor, and student-to-content), and is enabled by modern learning technologies (an integrated learning platform, as well as a variety of types of purpose-built video, web conferencing, and simulation software). The program issues block transfer credit to college graduates, and consequently reduces the time to completion when compared to other Bachelor’s degrees in Mining. The curriculum has been carefully designed to enhance a balance of technical, managerial, and societal skills for students. The program also includes short summer field school sessions, where students gain practical application skills under the direct supervision of engineering experts. THE NEEDS OF INDUSTRY Canada is the world’s largest exporter of minerals, and the contribution of this sector to Canada’s gross national product is more than three times that of the automotive industry, representing approximately 4% of Canadian GDP (MiHR, 2015)1. According to a recent report by the Canadian Mining Industry Resources Council (MiHR, 2016)2, despite the recent downturn in commodity prices, the industry will continuously need to attract new engineers to replace talent retirements and prepare for the possibility of expansion when the industry recovers. As past experience indicates, the challenges during expansion times are severe and the effects on education counter-productive. For example, during the prolonged expansion cycle of 2006-2012, several new programs were started worldwide, and mining became the profession of choice for many young students. During the subsequent downturn in the industry, many of these programs face dwindling enrollments, placing their sustainability in question. However, there is a continual need by industry to retain employees, as well as attract and train local talent, while providing educational opportunities to its employees. High potential college graduates can find themselves reaching a ceiling in their advancement due to their lack of a University degree. Furthermore, there exists an under representation of women, immigrants, and Aboriginal peoples in the labour force, and engineering fields in general1,2. Traditional mining engineering programs have tried to respond to the needs of industry, as well as meet the needs of students seeking diverse and successful employment careers. These programs tend to cater to the educational needs and aspirations of a general population, and their ability to grow and respond to changing industry needs is constrained by the number of students they can attract, as well as the resources available to them in a steady-state scenario."

Jan 1, 2017