Search Documents

By J. F. Edwards

In situ extraction of copper through borehole injection presents a new technology for the mining of copper. For the successful application of this technology, copper recovery at the surface must be specifically designed for borehole injection and the general conditions of the well field. This paper describes the design of a solvent extraction / electrowinning facility specifically designed for in situ leaching of copper. This design is based on commercial solvent extraction / electro-winning with considerations of the requirements of this specific application.

Jan 1, 1988

By J. Hanna

Four Ca-bentonitic clays from Alabama were evaluated for use in Diammonium Phosphate (DAP) or Urea Ammonium Nitrate (UAN) fertilizer suspensions. The viscosity and gel strength of suspensions prepared with different proportions of a Western bentonite clay and sodium exchanged Alabama clays, were measured as a function of clay content and dispersant concentration. The results obtained suggested that three of the Alabama Ca-bentonites would replace about 40% of the more expensive Western bentonite in UAN and DAP fertilizer suspensions. The performance of the Na-modified clays, prepared according to the TVA soda ash method, was as good or even better than those observed for the Mg-, Na/Mg-or K-modified clays. The TVA clay modification procedure appears to be reliable and cost effective.

Jan 1, 1989

By Marc Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molbydenum and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper price; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1980

By Lok W. Home

HISTORICAL DEVELOPMENT At the beginning of the 1970 more than 90% of pro¬duction drilling in open-pit mining was obtained with the use of rotary drills. At the same time, the use of rotary drills underground was virtually nonexistent. Several progressive mines began questioning whether efficient rotary drilling could not be adapted to under¬ground applications. In the late 60s and early 70s at¬tempts to use rotary drilling were made by Inco, Ltd. and Meramac Mining, utilizing drill units designed as a combination of small diameter raise drills and rotary drills. These initial attempts were unsuccessful primarily due to the immobility of the equipment and low degree of dependability. At the same time, experiments con¬ducted by Inco and Meramac using large diameter in¬the-hole percussion drills produced immediate encourag¬ing results. The first serious attempt at utilizing rotary drilling underground was made by Texasgulf in 1971 at Kidd Creek mine in Canada. An experimental stope 15 m wide, 36 m long, and 30 m deep was drilled using 200-mm diam rotary drilled holes. The machine used was a Robbins' Model 11 D. The Model 11D is a rotary drill designed to drill drain and utility holes under¬ground. The results of this test revealed that large diameter blasthole stoping was feasible. The indications were that the major areas of concern-fragmentation and pillar damage-could be controlled and a new low-cost stoping method resulted. At this point Texasgulf and Robbins entered into a cost-sharing agreement to develop a rotary drilling unit specifically for this stoping method. Drilling of the trial stope required pouring a concrete pad at each drill hole plus anchoring the derrick to the pad by means of rock¬bolts. Utilization expressed in terms of drilling time to available time was less than 20%. It was obvious that the required unit had to be mobile, setup time had to be minimized, and rod handling had to be improved. The first attempt at an underground production-type rotary drill consisted of mounting the basic 11D on an air-powered Eimco 600 Series crawler. The crawler was equipped with four screw-type leveling jacks operated by an impact wrench; rod rack facilities for 60 m of 1.2-m long, 170-mm diam rods; a rod handling facility consisting of an air-lift swing boom and a pipe loader which automatically positioned the rod under the float¬ing drive box; a turnbuckle anchor system requiring in¬stallation of four rockbolts in the drill drift floor and placing turnbuckles from the rockbolts to the corners of the drill; and trailing power units containing the electrics and hydraulics required to operate the drilling unit. Operation of this unit revealed a vast improvement in drilling time but some problem areas remained. The anchoring system required secondary drilling and proved difficult to adapt to the localized irregular floor surface and the trailing power unit was difficult to maneuver and was causing unnecessary maintenance costs. Addi¬tional improvements resulted in the standard 11MD rotary blasthole drill. DESCRIPTION OF UNIT This standard model consists of the drill and the power unit integrally mounted on an air-powered crawler chassis (Fig. 1). The rod-handling and leveling¬jack systems are similar to those used on the prototype Texasgulf unit and remained relatively the same. The anchoring system has been replaced by the roof jack, initially screw type but now hydraulically actuated. The anchoring system is necessary as the drill exerts more thrust than the weight of the unit. During operation it is found that the two front jacks adequately anchor the machine. The complete unit's operational dimensions are: height, 3.2 m; width, 2.1 m; and length, 4.2 m requiring a 3.5- x 3-m drill drift. The derrick is pivot mounted and raised and lowered by a hydraulic cylinder reducing the transport height to 2.5 m. The derrick is also turnbuckle mounted to allow dip angle drilling from vertical to 0.52 rad (30°) off vertical. The drill derrick can be mounted to allow dip axis to be parallel or perpendicu¬lar to the long axis of the unit. The standard rods are 1.2 m in length and are contained in racks of 10 which can be removed for transportation. Drilling torque is produced by a 56-kW (75-hp) electric motor driving a double vane pump which in turn drives a Robbins high torque gear-type hydraulic mo¬tor. In addition to the hydraulic motor, the machine drive system has a 3.9:1 planetary gear reducer. This results in six speeds with the following minimum and maximum range: Maximum rpm 112 Torque 3725.5 J (380 kg m) Minimum rpm 10 Torque 14 706.0 J (1500 kg m) Drilling thrust is provided by two bootstrap cylin¬ders pressurized by a variable volume pump. This sys¬tem can produce from 0 to 267 231.2 N thrust in either direction. Bailing air (approximately 17 m3/min at 382.2 to 490.3 kPa) is introduced through a rotary swivel pass¬ing directly through the center of the drive system to keep efficiency and losses to a minimum. Hole annulus is also kept to a minimum by using 170-mm rod when drilling a 200-mm hole. A small amount of water is added to the air for dust suppression. The machine has to be supplied with air, water, and electrical power. It does not appear feasible to provide an integral air power supply with the rotary drill such as is done with open-pit rotary drills. Air is required and installed during the primary development of the drill drift. The machine can be adapted to drill hole diameters from 170 to 228 mm for blasthole operations. The drill string consists of the rotary bit, crossover stabilizer, roller stabilizers, and standard rods. The operator controls speed and thrust pressure from an operating console which can be mounted in a conve¬nient position. Mount Isa has made an adaption to the operating console to permit remote collaring of drill holes in an uncleared floor.

Jan 1, 1982

By J. A. Pigott

Undercut-and-fill mining is a method developed by the International Nickel Company to deal with abnormal pillar mining conditions at one of its mines. Results have been such that its use has been extended to normal, pillar recovery operations in other mines of the Company as a replacement for conventional square-set pillar mining. It is anticipated that the method will also largely replace square-set stoping at INCo mines, especially for mining at deep horizons.

Jan 1, 1962

By Barry R. Doyle, Emma C. Ross

This paper presents a 20-year global account of tunneling in gassy ground demonstrating high probability of schedule delays, cost overruns, worker injuries and fatalities. Causes of these failures are systemic. Gas is seldom characterized in terms relevant to design of effective ventilation systems. Control measures deployed in tunnels are often based on outdated industrial safety codes. A change in approach is needed. This paper describes how to perform a desk study to determine if field investigation for gas is warranted, and lists the content of an effective characterization of gas in a geotechnical report.

Dec 1, 2022

By R. W. Lai

Cyclic voltammetry (CV), flotation response, evolved-gas analysis (EGA), and X-ray photoelectron spectroscopy (XPS) were employed to evaluate the major differences in the surface property and surface reactivity of coal pyrite and mineral pyrite.

Jan 1, 1989

By A. L. Hannaford

Previous production at Spektakel was undertaken during the periods 1854 - 1888 and 1892 - 1901. During this period a total of 41,7 kt of ore grading 32% Cu was hand-sorted from 270 kt to 360 kt of ore mined. Initial open-pit mining was followed by underground mining, access being by means of an inclined shaft to the 85 fathom level. During the period 1946 - 1952 cement copper equivalent to 5,452 kt of blister was produced by leaching of oxidized ore. The Spektakel ore-body branches and coalesces both in plan and in cross-section which accounts for its remarkably complex configuration. Constituent rock-types are andesenite and various varieties of biotite diorite and of ?norite? (biotite-hypersthene diorite). Closely related spatially, and possibly genetically, but predating the above-mentioned basic rocks are bodies of biotite-bearing monzoritic rocks, locally termed shonkinita.

Jan 1, 1981

By Brian J. Gorva

The key objective of forming a cartel is to increase profits to members of the cartel by taking the following action: a) control output; and b) control price. However, while attempting to obtain monopoly profits the cartel members have to contend with costs associated with cartelization and such costs include the following: political costs; the cost of coordinating output and price; organizational costs (such as cheating); and administrative costs (such as the cost of attending cartel meetings). The objective of commodity exchanges is to provide an open, free market where buyers and sellers may openly complete transactions and pricing information can be immediately disseminated. These transactions include the following: a) to provide facilities for "hedging", or transferring price risk from buyers and sellers of physical commodities to "speculators" through the medium of buying and selling futures contracts, and b) taking physical delivery of metal on due dates.

Jan 1, 1983

By Christopher Nelsen, Daniel Dobbels, R. Zachary Hollenbeck

Recent major floods have inundated Historic Ellicott City, Maryland, resulting in loss of life and property damage. Howard County, Maryland, has developed the Ellicott City Safe and Sound Plan to mitigate the risk of flash flooding in the Historic District, including a proposed stormwater conveyance tunnel. Challenges to overcome include thick zones of saprolite along the alignment, multiple near-surface structures, and minimal rock cover under an active railroad, while minimizing impacts to the public and historic structures. The project will also pursue recognition through the ISI Envision verification process.

Dec 1, 2022

By Karoly (Charles) Kocsis, Jeff Johnson, Felipe Calizaya, Tulio Dias, Natanna Nunes

Two pressure balancing chambers were constructed at a Colorado coal mine to reduce the risk of spontaneous combustion. Each chamber was established by installing a Kennedy stopping at about 10 ft (3 m) in front of an isolation seal, and equipped with two safety doors, a nitrogen injection system, and a set of environmental monitors. Several pressure balancing tests for different ventilation conditions were conducted in these chambers. During each test, pressurized nitrogen was injected into the chamber and the pressure differentials across the stoppings and seals monitored. This study presents a summary of the results achieved, lessons learned, and the basic requirements to operate a pressure chamber effectively.

Feb 1, 2024

By Gerald W. Elger

Research at the Albany Metallurgy Research Center has shown that high-purity rutile can be produced from relatively low-grade ilmenite obtained from a massive rock deposit. Ilmenite is first smelted in an electric-arc furnace to separate the iron and produce a slag enriched in titanium dioxide. Titania slag mixed with a phosphate flux is then oxidized to synthesize rutile and form a phosphate-glass matrix which contains the impurities. Attrition scrubbing the treated slag in dilute solutions of phosphoric or sulfuric acid liberates the rutile, which is concentrated by physical methods. Tests show that synthesized rutile containing 95 to 97 pct titania responds to chlorination at the same rate as natural rutile.

Jan 1, 1973

By Thomas R. Kuesel

Just south of the L'Enfant Station in Seventh Street, the WMATA system splits into two branches, each comprising twin single-track soft ground tunnels. Immediately at the beginning of the section, Interstate Route 95 crosses transversely over the alignment in open cut, removing most of the cover over the tunnels. Seventh Street spans I-95 on a bridge whose abutments and pier also cross transversely over the four tunnels, with their footings as little as 7 feet above the tunnel crown (Figure 1). Soil investigations revealed that the tunnels would have to be driven through mixed face, with a clay invert and a waterlogged sand crown. Thus, there was a good chance that the roof would fall in, leaving 1-95 and the Seventh Street Bridge in a crater. Since there was no roof that could be counted on, these were figuratively (and potentially truly) Washington Metro's Topless Tunnels (Figures 2 and 3). DESIGN ALTERNATIVES Faced with this situation, the designers considered several options, including temporary detours that would permit demolition of the bridge and building tunnels under the 1-95 Freeway by cut-and-cover methods. They also investigated structural underpinning of the bridge and freeway pavement, and strengthening the bridge abutments and center pier by post-tensioning to enable them to span over any subsidence trough.

Jan 1, 1976

By J. C. Bradbury

The Illinois State Geological Survey's program in industrial minerals is twofold-the gathering of information on mineral raw materials and the generation of data on the use of these materials. The first function is carried out by the Industrial Minerals Section and the Clay Resources and Clay Mineral Technology Section of the Geological Group, and the second is the responsibility of the Chemical Engineering Section of the Chemical Group. Gathering in formation on raw materials includes both mapping of resources and fundamental geological research. Recent and current research projects include studies relating lithologies of limestones to their physical properties, investigation of sulfur dioxide reactivity of various types of limestone, lithostratigraphic studies of limestones of Mississippian age, investigations of heavy minerals in Cretaceous, Tertiary, and Pleistocene sands, studies of the environments of clay deposition, electron microscope studies of clays and limestones, and investigation of long-term expansion in ceramic products. A relatively recent development that relates more to dissemination of information than to research is environmental geology. This affects the Survey's industrial minerals program chiefly by stimulating the study of rock and mineral resources in metropolitan areas and reporting the results for the land- use planner as well as the engineer or mineral producer. The Survey's program of research on the use of industrial minerals was expanded and diversified in 1966. Incorporating a minerals beneficiation lab, the program is designed to develop new uses for existing mineral resources and to assist producers in implementing these ideas: Projects of the minerals engineering program have included the separation of a feldspar concentrate from certain glacial outwash and river sands, recovery of kaolinite from the waste from silica sand operations, development of the use of an Illinois clay as a binder for pellets, and investigations into the use of fly ash and fluorspar mine tailings.

Jan 1, 1970

By Milan Yekich, Emanuele Cauda, Justin Patts, Cody Wolfe

A worker’s personal exposure to respirable dust in occupational environments has traditionally been monitored using established methodologies which entail the collection of an 8-hour representative sample that is sent away for laboratory analysis. While these methods are very accurate, they only provide information on the average exposure during a specific time period, generally a worker’s shift. The availability of relatively inexpensive aerosol sensors can allow researchers and practitioners to generate real-time data with unprecedented spatial and temporal granularity. Low-cost dust monitors (LCDM) were developed and marketed for air pollution monitoring and are mostly being used to help communities understand their local and even hyper-local air quality. Most of these integrated sensing packages cost less than $300 per unit, in contrast to wearable or area dust monitors specifically built for mining applications which have been around for decades but still average around $5,000 each. At the National Institute for Occupational Safety and Health (NIOSH), we are leveraging the power of high-volume data collection from networks of LCDM to establish baseline respirable hazard levels and to monitor for changes on a seasonal basis as well as following any application of control technologies. We have seen the effective use and advantages of monitoring live data before, during, and after events like shift changes, operational changes, ventilation upgrades, adverse weather events, and machine maintenance. However, many factors have prevented a systematic adoption of LCDMs for exposure monitoring: concern for their analytical performance, the complexity of use, and lack of understanding of their value are some factors. This contribution outlines a one-year case study at a mine in Wisconsin USA, covering the installation, maintenance, data visualizations, and collaboration between NIOSH researchers and the industrial hygiene professionals at the mine.

Feb 1, 2024

By Biswajit Samanta, Rahul Kumar, Pranjal Pathak

The Open Pit Mine Production Scheduling Problem (OPMPSP) is a complex optimization problem that seeks to determine the best sequence for extracting mineralized material from the ground in order to maximize the Net Present Value (NPV). This process must take into account various capacity constraints, such as mining rates, processing limits, stockpiling capacities, blending requirements, and precedence constraints, which dictate the order in which blocks can be extracted. Traditionally, the OPMPSP has been formulated as a mixed integer programming problem, employing binary and continuous variables to represent the extraction of each block. However, this approach has limitations, particularly when it comes to addressing the stockpiling issue. In response, some researchers have proposed mathematical models, which offer a more accurate representation of the problem but come with their own set of challenges. In this study, an alternative approach to tackle the OPMPSP with stockpiling by employing constraint programming (CP) is explored. The method was carefully tested on the Newman1 dataset from the well-known Minelib library. The results show that the CP-based model obtained a production schedule having about 2.69 % higher NPV than the NPV of the solution, which is recorded in the Minelib Library.

Jun 25, 2023

By W. P. Blacutt

A financial-economic model incorporating physical, market, and policy variables is developed for mining investment in Bolivia. Additional risk criteria emanating from political instability. new mining legislation, recent environmental regulations, and a new minerals taxation system are accounted for and are integrated into the investment decision model. Results of the model indicate that geologic and market variables have the dominant effect on the investment-worth function. Among policy variables, exchange rate and taxation policies have the most significant influence. Depreciation allowance for infrastructure development has negligible weight in the investment-worth function. The business structure of the firm considering investing in the Bolivian Polymetallic Project is found to be an instrumental factor in the investment-worth outcome. Specifically, undiversified mining companies whose operations exclude zinc production as the primary source of revenue would benefit most from adoption of this project.

Jan 1, 1993

By W. A. Hoyer

Neutron activation analysis for mineral identification has attracted the attention of numerous investigators, judging from the publications on this subject in the past few years. 1-9 The appealing aspect of this method of mineral analysis is its proven sensitivity in the laboratory. In principle, activation analysis is one of the few petro-physical methods whereby a direct analysis for a mineral itself is possible in a borehole. The successful application of activation analysis requires the use of particular neutron reactions, measurement of selected gamma-ray energy intervals, and optimum bombardment and detection times. For copper analysis, Labanov et al., 10,11 using a low-energy PuBe source, reported an acceptable logging means. On the other hand, Pradzynski12, in analyzing ores and process tailings, used high-energy neutrons and photons for surface measurements of process samples. The work of Labanov et al. was based on measuring the rate of decay of the activated copper and hence was not as definitive as might be desired. Equipment is commercially available to carry out activation studies in the field 13,14 Gamma-ray spectra can be successfully transmitted over ordinary logging cables and, with borehole high-energy neutron accelerators and lower-energy chemical neutron sources, a variety of neutron activation methods can be studied. The purpose of the study discussed in this paper was to determine the feasibility and practicability of logging for copper using neutron activation techniques and commercially available equipment. The laboratory study showed that Cu could be detected in rock samples in the laboratory by high-energy neutron activation of 63 Cu. In the field, however, due in part to the large volume irradiated, the direct detection of copper using high-energy neutrons was not as promising. Detection of copper by measuring both the direct gamma-ray emission and the excessively strong low-energy gamma-ray absorption appears promising. Copper was not detected either in the laboratory or

Jan 1, 1972

By W. Blake, J. Whyatt

Sixty years of rock bursting in the Coeur d'Alene district has taught painful lessons and led to a number of practical advances in controlling rock-burst hazards. This paper summarizes these lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rock-burst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rock-burst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d'Alene district experience.

Jan 1, 2003

By Su Yang, Pang Shun, Xiaoding Xu, Guodong Yang, Hengfeng Liu, Meng Wu, Yuejin Zhou

By introducing the hydrochemical damage variable of coal gangue granular material, this paper analyzed the evolution law of gangue mechanical parameters with hydrochemical damage. By constructing a gangue damage model considering multifield coupling, the damage mechanism of gangue under multi-field coupling was revealed from the microscopical aspect, and the influence law of gangue damage mechanism on the dissolution of toxic substances under multi-field coupling was obtained: the conditions of Test 1 have the greatest influence on the porosity of coal gangue, and the damage of coal gangue is the greatest. Cu, Zn, Cd, and Pb are more easily leached under acidic conditions. The coupling effect of seepage, temperature, and chemical field can promote the formation of secondary voids, change the voids, and form migration paths in coal gangue. The kinetic model of toxic leaching of coal gangue under multi-field coupling can be well characterized by Elovich equation. The release mechanism of heavy metals is mainly manifested as delayed diffusion or dissolution in the early stage, diffusion and dissolution in the middle stage, and depletion in the late stage.

Nov 23, 2023