Search Documents

By Chris Chmura, Ketut Karmawan, Ian J. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of West Papua, Indonesia. Present production from PTFI’s DOZ Underground Block Cave Mine is approximately 40 thousand tonnes per day (ktpd). This paper describes the design process and recommended ventilation infrastructure necessary to expand the DOZ Mine reserves and to increase sustained daily production above 50 ktpd. The enlarged footprint will feature longer production panels of up to 650 m in length, more active draw points, a second large gyratory crusher, and additional men and mobile equipment. The increased ventilation capacity will be achieved through the development of new, dedicated ventilation drifts, and primary Underground exhaust fans.

Jan 1, 2005

By B. H. Richard, P. J. Wolfe, T. G. Holdeman

Guided seismic wave propagation was studied in the Lower Freeport (6A) coal seam in the Oak Park No. 7 mine near Cadiz, OH. Three component geophones were implanted in the coal at distances ranging from 72 m to 183 m from the seismic source. Both Love- and Rayleigh-type modes were observed but the Love-type mode produced the best data. Detailed analysis was performed on the best Love data and a Dziewonski map of group velocity vs. frequency was constructed. This map was in excellent agreement with a theoretical dispersion curve calculated for a model of the coal seam. The Love wave group velocity was found to have a minimum value of 510 m/sec at 275 Hz. Only the fundamental mode contributed significantly to the observed signal and it was observed up to the maximum distance available.

Jan 1, 1987

Changes have been made in the Bulletin, Section I., for this month ; Personal and Employment columns have been added, and a Forum, in which will be included letters and discussions of general interest to members of the Institute ; live news and new matter have been inserted near the front; lists of officers and committees are placed next to the technical section, while standing matter and other information which is interesting chiefly when sought for, has been segregated as much as possible. Members are urged to co-operate with the Editor by sending in news items of themselves and others, and by giving some of their spare time to this department each month.

Jan 4, 1913

By Hugo J. Garcia, M. C. Fuerstenau, D. M. Lupan, J. L. Hendrix

Biodegradation of cyanide by microorganisms isolated from solids previously exposed to cyanide has been investigated. The anaerobic cyanide biodegradation showed good, short-term removal of cyanide in the presence of nutrients (medium A). This system retained metabolic activity at cyanide concentrations up to 300 ppm at pH 10.5. Microscopic examination of stained specimens revealed that the bacteria were Gram-negative, rod-shaped bacilli. Strains capable of cyanide decomposition were identified as Pseudomonas and Alcaligenes. The kinetics of biodegradation were found to be first order with respect to cyanide concentration, and the overall reaction rate constant is k = 0.102 day-1. Studies with Na14CN showed that 17 % of 14C transformation went into the cells, 18 % into carbonate and 47 % into bicarbonate.

Jan 1, 1995

By O. Fernandez, M. Vesely

Abrasive grinding, leading to ultrafine product and "critical size" material buildup inside the mill, is proposed as the cause of high power consumption and low capacity in many fully autogenous grinding processes. Addition of steel balls (hence, semiautogenous grinding) or pebble removal and separate crushing have been used, with different efficiencies, to overcome the problem. Information and data for the conceptual analysis, basic design, and operation of a pebble crusher at the Los Bronces semiautogenous grinding plant is presented along with data showing a production increase of 1000 t/d (1100 stpd) and significant operating costs savings.

Jan 1, 1987

By Bekta? Uz

In this research, geological characteristics of sand quarries around the village, Kemerburgaz Akpinar, are studied and the mineralogical, petrographical, chemical and technological characteristics (such as sieve analysis, relative density, water absorbtion etc.) of the sand samples, obtained from the area are explained. In the general area sand' quarries, being in lacustrine formations belonging to Neogen, the stratigraphic location of the sand occurences take place at high levels of these formations, geologically. All of this pattern, being under 1 mm with a ,particle dimension, it ranges from 0,5 mm in the quantity of 99 % to 0,25 mm in the quantity of 15 relative density is 2,65 g/cm3 ; water absorbtion is 0,9%. Mineralogically, the sand samples contain Quartz (84%), Feldspar (3%), Calcite + Aragonite (10%), Pyroxen+Amphibole (1-2%), Garnet+Tourmaline (0.5%), Olivine (0.1-0.5%). Besides, sand samples contain SiO2 with the quantity of above 90%. Containing Quartz at high levels for mineralogical, petrographical and chemical characteristics, Akpinar sand will be evaluated as silica sand when the carbonate mineral is removed with the method of ore preparation such as leaching.

Jan 1, 2005

By Antti J. Niemi

Radioisotope tracers have so far been used for extraction of residence time distributions of flotation devices. They have also been proven applicable to evaluation of rate coefficients k of industrial flotation. It is now shown how values of k are scaled up on the basis of laboratory data on flotation and chemical conditioning, and of laboratory testing of samples from output of industrial conditioning vessel. Subsequently a model of conditioning and flotation is obtained which may be used for simulation and control of the steady state of the combined process. Discussion extends to modelling, simulation, CAD and opti- mization of flotation plants with re- circulation, and of ore dressing systems which consist of grinding and flotation plants.

Jan 1, 1990

By John O. Marsden

The project development metallurgist is faced with an interesting dilemma: The use of overly conservative metallurgical projections and cost estimates can kill a project that has the potential to provide needed jobs and growth to a company's bottom line. On the other hand if the metallurgist uses a highly aggressive approach by trimming capital and operating cost estimates to the bone and by applying highly optimistic metallurgical projections, there is a risk of creating a project that can never live up to expectations. The metallurgist must walk a tightrope between "sandbagging" and "overoptimism," and this tightrope is fraught with political intrigue and difficulty. This paper takes a some- what lighthearted look at some of the political aspects associated with this issue, and other issues, and offers a few guidelines for walking the "political metallurgical" tightrope.

Jan 1, 2001

By D. R. Schmitt, B. L. Jensen, T. J. Ahrens, C. L. Smither

The in situ elastic moduli of rock are measured holographically by a borehole instrument in marble and oil shale. A point force induced displacement field is recorded with double expo- sure holography. Data consists of a fringe pat- tern on the viewed hologram. The elastic moduli are determined by modelling of the fringe pattern. Only Young's inodulus is fairly constrained by the present data reduction. For an applied force of 520 [ ] 50 Newtons, a marble was found to have a Young's modulus of 56 [ ] 8 GPa, near an ultrasonically determined value of 48 [ ] 6 GPa. In an oil shale, an applied force of [ ]

Jan 1, 1986

By V. K. Karra

Research by various workers has shown compressive comminution to be significantly more efficient than impact comminution. Based on the work being done at Nordberg, wet compressive crushing in cone crushers producing finer and finer products, shows the feasibility for partial substitution of conventional tumbling mills. For further substitution, major challenges are processing of fine feed slurries in cone crushers to realize a significant size reduction of the particles, and understanding the limitation of the gyratory type units in terms of finest product achievable. The paper addresses the challenges involved, efforts at Nordberg, and the implications to conventional comminution flowsheets.

Jan 1, 1989

By F. M. Doyle, S. M. El-Raghy, M. F. El-Demerdash, E. Peters

The Activity Distribution Diagrams (ADD) developed by the authors are computed for Cu-S-H2O and Mo-S-H2O systems. The distributions of metal and sulfur between all species are estimated against pH at different potential levels. Both M-H2O and S-H2O distributions are compared to the M-S-H2O distributions to estimate the changes occurring due to the presence of sulfur. The method of computation follows the Activity Term Criterion, taking into consideration the multi-equilibrium interrelations and conservation of mass. Results are analyzed in terms of dividing a distribution curve into three basic segments. These segments are formation, stability, and dissolution.

Jan 1, 1993

The primary goal of a maintenance information system should be to aid the maintenance department in providing the required equipment or plant availability at the lowest possible cost. To achieve this goal, the system must provide information in support of the following objectives: (1) establishing the best fleet, equipment, and component configuration; (2) establishing the best maintenance program; (3) executing the defined maintenance program efficiently; and (4) monitoring equipment availability. These objectives can be satisfied with five groups of reports. Each of these groups should provide regular, periodic reports to aid in planning and monitoring trends, exception reports to identify problems, and on-request reports to provide analytical capabilities.

Jan 1, 1979

By Malcolm J. McPherson

This paper describes the algorithm used in a BASIC program for an IBMXT microcomputer, to simulate the underground mine climate. The program called CLIMSIM has been developed and refined over several years as a result of considerable use at operating mines. The program has been designed to be easy to use and be understood by the practicing mine ventilation engineer. It provides predictions of the work place climate, so that the optimum ventilation/cooling system can be designed to obtain a certain air cooling power or effective temperature at the work place. An example is given of the application of the program to a mechanized cut and fill stope at the Homestake gold mine in South Dakota.

Jan 1, 1986

By W. Petruk

Mineral liberations that would be obtained by grinding an ore to a specific size can be predicted by analyzing unbroken ore pieces, and mineral liberations in ground ores and mill products can be determined directly by image analysis. Predictions of mineral liberations are made by measuring size distributions and textures of mineral grains by image analysis and using liberation models. Ground ores and mill products are analyzed to determine the proportion of mineral that is liberated, and the data are used to evaluate mineral behavior during mineral beneficiation. The liberation data for minerals in a suite of mill products from a circuit are processed by a materials balancing technique to calculate recoveries of minerals in different types of particles throughout the circuit. The liberation-materials balance data define mineral recoveries; define the behavior of an ore in a concentrator, pilot plant or bench test: and indicate whether recovery improvements are possible and/or feasible.

Jan 1, 1992

By S. C. Bandis, N. Barton

During drilling of deep boreholes, local mechanical failures of the wellbore walls may occur due to the inability of the incompetent overburden and reservoir rocks to withstand drilling-induced changes of the stress environment. At present, borehole failure mechanisms in three-dimensional stress fields are poorly understood. Our experimental investigations based on 3-D physical models demonstrate the stabilizing effect of the intermediate principal stress. The latter may play a dominant role in maintaining the integrity of the stress relieving failure zone around the borehole. However, this will depend on the stress anisotropy, the angle of hole deviation and on the angle of internal friction. Our tests also indicate that the failure zone can accomodate high extensional strains. Finally, relations between the physical models and closed-form elasto-plastic solutions are discussed.

Jan 1, 1986

The purpose of this paper is to describe two systems designed to provide estimations in stratigraphic orebodies for the purposes of detailed mine planning. The first is a completely geostatistical approach and the second is a combined geostatistical/deterministic approach. The essential features of both systems are the estimation of stratigraphic ore boundaries and the subsequent use of those boundaries to provide stratigraphic (or zonal) control for block and point grade estimation (kriging). Both systems are illustrated by application to a section of, the Hilton orebodies, Queensland, Australia.

Jan 1, 1989

The objective of the fines flotation step in a coal preparation plant is to maximize coal recovery subject to a constraint on the allowable ash in the concentrate. The objective is achieved when the incremental ash is driven to a target value determined by an economic constraint. In this paper, a phenomenological flotation model and ash analyzer combination are identified that allow the development of a soft sensor for incremental ash and subsequently a model-based strategy which manipulates key flotation variables to achieve the control objective. A combination of plant tests and computer simulations are presented to evaluate control-system performance in one operation.

Jan 1, 1999

By Po-Wei Tun, Kuen-Yuh Wu, Tso-Min Shih, Hsi-Chiang Fang

The purpose of this study is to investgate the coal dust explosion characteristics and to search for the prevention methods of the coal dust explosion as well as the propagation of the explosion flame of the middle-bearing coal formation in Taiwan by an open type coal dust explosion apparatus in laboratory. The coal samples were taken from the typical middle-bearing formations of the Sam-Ming,Tai-Ho and Lee-Fong coal mines The rock dusts, the free water mixture with coal dust samples and the interval clean out the coal dust in the testing chambers were applied for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1993

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process nominal 1.2 x 0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm. Keywords: Coal recovery, Coal refuse, Dense-medium cyclone, Hindered settling, Spiral concentration

Jan 1, 2003

By Prasannarao Dontula, Kal V. S. Sastry

Advances are made in the field of mineral processing on a continuing basis both in the industry and the academia. These advances do not always get used fully because of the inherent difficulties in the transfer of knowledge and reduction to practice. In recent years, knowledge engineering is being increasingly employed in other fields to overcome some of these difficulties. This paper presents a vision of how knowledge engineering can be applied to the benefit of the mineral processing industry and includes a discussion of associated principles, techniques, and advantages.

Jan 1, 1993