Search Documents

By S. C. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photoelastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface, and (3) the effects of subsidence on tension in the truss members.

Jan 1, 1987

By Frank E. Dalton

The Metropolitan Sanitary District of Greater Chicago (MSDGC) serves an area of approximately 860 square miles and collects and processes used water from the city of Chicago and 116 surrounding communities. As a public agency, the MSDGC -Serves a population equivalent to 10 million people which is composed of 5.5 million people and an industrial wasteload equivalent to an additional 4-1/2 million people. -Provides 400 miles of intercepting sewers and tunnels ranging in diameter from 12 inches to 24 feet. -Operates 71 miles of navigable waterways and channels conncecting the Atlantic Ocean and the Great Lakes with the Gulf of Mexico and 6,000 miles of inland waterways. -Maintains the largest water reclamation plant in the world. -Processes 1,380,000,000 of used water daily and removes approximately 1,000 dry tons of organic solids each day. -Has spent approximately 700 million dollars in capital improvements to date, and will require expenditures in excess of 3 billion dollars (including over one-half billion dollars in tunnels) to meet existing federal and state water quality standards.

Jan 1, 1974

By J. M. Kruger, P. Berendsen, A. Martinez

High-resolution ground-penetrating radar (GPR) was used to image the near-surface extent of two exposed Late Cretaceous kimberlites intruded into lower Permian limestone and dolomite host rocks in northeast Kansas. Six parallel GPR profiles identify the margin of the Randolph 1 kimberlite by the up-bending and termination of limestone reflectors. Five radially intersecting GPR profiles identify the elliptical margin of the Randolph 2 kimberlite by the termination of dolomite reflectors near or below the kimberlite's mushroom shaped cap. These results suggest GPR may augment magnetic methods for the delineation of kimberlites or other forceful intrusions in a layered host rock where thick, conductive soil or shale is not present at the surface.

Jan 1, 1998

By M. G. Karfakis, K. P. Chong

Determination of fracture toughness using the semi-circular specimen, the chevron edge notch round specimen, the short rod specimen and the cylindrical burst specimen, are critically reviewed. These methods, among all, are the most applicable for fracture toughness determination of rocks. They require minimum machining. Samples are small, and testing procedures are simple. They have a sound analytical basis and allow the fracture toughness to be determined without measurement of fracture length.

Jan 1, 1986

By K. Y. Haramy, B. T. Brady

A scale-invariant theory of the strength and deformability, of rock masses in static equilibrium and at incipient failure is proposed The theory provides a rationale, for designing structures in rock. This paper presents results of experiments conducted by the US Bureau of Mines and presents theoretical methods to determine and interpret the in situ strength of rock masses using the borehole shear tester.

Jan 1, 1996

By Donald S. Clarke

The Umuna epithermal precious metal deposit has provided the target for a simulated rock geochemistry exploration program, directed at bedrock exposed in the drainage system of eastern Misima Island. A geochemical halo to the deposit is readily recognised in the mafic meta-volcanic country rock. This halo is defined by anomalous results for both major (K, Na, Ca, Mg) and minor (Au, As, Sb, Cu, Pb, Zn, Ba, Rb, Sr, Cs, Bi, Ga, S) element geochemistry, extending further than 1km from the deposit. Such halos are sufficiently extensive to provide adequate exploration targets in the search for epithermal mineralisation, complementing mineralogic and secondary media geochemical investigations.

Jan 1, 1989

By Kenneth R. Miller

Surface mine equipment operators in the Campbell County region of Wyoming's Powder River Basin have found new ways of solving old problems. Technology, experience, competitive pressures and an increasing grasp of economies of scale have driven mine operators, equipment manufacturers and suppliers to specialization of applications. In economic terms, today's coal price of $4.95/t ($4.50/st) equates to $2.53/t ($2.30/st) in 1980 terms - an incomprehensible value at that time. This article describes some examples of change and adaptation made by Powder River Basin coal operators in overburden stripping equipment and techniques. It focuses on the evolution of the design and use draglines, shovels, trucks, scrapers and dozers.

Jan 1, 1998

By J. Alton Burks, Robert R. Stein

This paper focuses on the noise exposure levels of miners employed on longwall production faces. Along with the increased production from longwall units has come the potential for greater noise exposures. Typical noise levels are given for the various noise sources that are present on modern longwall faces. Exposure times have typically increased since the introduction of longwall technology in this country. Representative exposure times and patterns are analyzed. Possible solutions are presented for generalized cases. Engineering controls developed by the Bureau of Mines are explained and their potential effectiveness is calculated for the cases presented. The role of hearing protectors in an overall hearing conservation program is also investigated. Recent research performed by the Bureau suggests that the actual performance level of muff -type protectors may be less than the manufacturers ratings under certain circumstances. The use of muff- type protectors is discussed and analyzed with respect to their use on longwall operations.

Jan 1, 1992

By L. M. Klimov

In recent gears in the coal industry a great deal of attention is attached to the questions of elaborating and introducing the problems of planning and management and, first of all, in the sphere of mine production. The basis for planning of mi- ne production is complexes (sets) of problems for planning the development of mining operations based on different time periods, ensuring the follow-up of changes of mine productive capacities. Complexes of problems for planning, the development of mining operations at existing underground and surface mines within the OASUugol system (Coal Industry-wide Automatic System of Management) are aimed at ma- king decisions close to optimum, i.e. general lay-out of panels, blocks and pillars; transport and ventilation networks; schedules for working out parts of mine take; coordinated mining operations with limited labour and material resources; control of mining operations and ultimately maintaining productive capacities of existing mines at the required level.

Jan 1, 1979

By Greg Blerie

The requirements placed on belt conveyors grow increasingly complicated No longer is it sufficient for the conveyors to merely move material from "Point A" to "Point B. " Now these systems must be able to produce a specified flow, guaranteeing a plant can operate as scheduled without peaks and valleys in material flow and production rate. In addition, the conveying system must provide effective control, to minimize the problems and costs associated with the escape of fugitive material these problems include unscheduled shutdowns, premature equipment failures, regulatory headaches, poor neighbor relations, and health and safety issues. The key to accomplishing these goals is the loading and discharge of the conveyor belts. Fortunately, new designs for the chutes that accomplish conveyor loading and discharge can move material efficiently, without blockages and while minimizing the amount of dust generated This innovation is the development of engineered flow chutes

Jan 1, 2004

By C. Bazin, D. Hodouin

Dynamic experiments were performed in a continuous open-circuit 40x40-cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transferfunction and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model, a minimum variance controller with constrained input is designed and its performances are compared, by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By J. A. Brierley, Arpad E. Torma, Victor C. Storhok, C. L. Brierley, Batric Pesic

Chemical and electrochemical studies were performed during bioleaching of cobaltite concentrate with Thiobacillus ferrooxidans. The two principal minerals present in the concentrate were pyrite and cobaltite (CoAsS). During chemical studies, the effect of pH on dissolution rates was examined under uncontrolled and pH-controlled conditions. It was found that in the pH range 1.5-3.0 there was no pH effect if the initial pH was not controlled (maintained). When the initial pH was controlled, the leaching of Co, As, and Fe depended strongly on pH. Electrochemical studies were performed by using cyclic voltammetry and constant potential techniques. A sequential reaction mechanism was proposed for dissolution of cobaltite.

Jan 1, 1993

By John B. Comer

Compelling evidence indicates that at least the plateau bauxite of northern and central Jamaica formed from volcanic ash. The predominance in plateau bauxite of zircon grains younger than the host limestones and the relative abundance of zircon grains having idiomorphic form support a direct ash-fall origin for much of the bauxite parent material. Based on revised mass balance calculations, not enough of the middle Eocene to lower Miocene host limestones have been dissolved to make an important contribution to bauxite. Likewise, the pre-middle Eocene rocks of Jamaica have made only a very small contribution to plateau bauxite; they may have made a more significant contribution to the graben bauxite of southern Jamaica.

Jan 1, 1984

By T. Seal

The Hydro-Jex technology has been used by Newmont Mining Corp. on the gold heap leach pads on the Carlin Trend - Nevada for three years to recover the inventory gold and change the chemistry in the pads. This research and development patented process is complete with the resultant data presented. Information on drill sampling, geophysical surveying, followed by leach pad stimulation with impacts on solution chemistry and gold recovery are discussed. Can this technology be used to rinse and close heap leach pads faster with reduced pump energy costs and improved recovery?

Jan 1, 2007

By Les T. Zoschke

Over ten years ago, Modular began development and implementation of its DISPATCH System for haulage optimization in open pit mines and now has over two dozen systems in operation worldwide. The so-called 'top down' approach used in system design and implementation was deliberate. This foresight now allows addition of features which would otherwise prove infeasible - without complete system redesign. Until recently, truck and shovel operator input provided timing data needed for optimal allocation. Now, addition of a high-speed, general purpose token ring loop controller and infrared (IR) transponders to each piece of mining equipment automates these important functions. Here, we discuss new devices, systems, and subsystems comprising mining's future.

Jan 1, 1992

By Tomb. T. F., R. A. Haney

During the past several years, the Mine Safety and Health Administration (MSHA) has conducted studies in underground mining operations to obtain information on occupational exposures to diesel particulate (DP), mine environmental DP levels and on the effectiveness of methodologies used to control DP. The studies conducted were representative of four coal mines and 10 metal mines. The metal mines included two lead-zinc mines, one limestone mine, two potash mines, one zinc mine and four salt mines. Three of the four coal mines were using disposable diesel exhaust filters to remove particulate from the exhaust and one was using a reusable wire mesh filter. Results of these studies indicate that average DP levels in coal mines not using exhaust filters range from 0.9 to 2.1 mg/m3, The use of exhaust filtration devices reduced these levels by about 50% to 90%. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1996

By Timms. Greg P., John W. Bennett

A field-based method for measuring the diffusive oxygen flux through covers placed on sulfidic waste rock dumps has been developed and applied at a number of mine sites. The technique provides a means of quantifying oxidation rates in dumps and can thus be used to assess the effectiveness of cover systems. Two instruments can be used. The first is portable and easy to set up, enabling a picture to be built up of the overall diffusive flux into a dump by making measurements at a sufficient number of locations. The second is installed beneath a cover and is preferred in situations where oxygen is consumed in the cover since it provides a direct measurement of the oxygen flux into the underlying waste rock.

Jan 1, 2000

By J. B. Hiskey, P. H. Qi

Activated carbon loaded with gold from different halide solutions was characterized by thermal analysis (TA) techniques. The mechanism of gold uptake by carbon varies from predominately adsorption for gold iodide to predominately reduction for gold chloride. Thermogravimetry analysis (TGA) and differential thermal analysis (DTA) measurements confirm the existence of adsorbed gold-halide species within the micropore structure of carbon. These results suggest that the ratio of reduced to adsorbed gold increases for gold halides in the following order: Au-I < Au-Br < Au-Cl. In the case of Au-I, TA results for the loaded carbon were compared with pure compounds of 12, Aul and Aul3.

Jan 1, 1998

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. This sludge is a result of reacting limestone with sulfur dioxide to precipitate calcium sulfite and calcium sulfate. The majority of the sludge is simply landfilled, but with increasing landfillimg costs this can cost the plant millions of dollars per year. As a result, this option is rapidly becoming less attractive. Producing marketable materials from the sludge is a far more promising avenue, provided that the products can meet the necessary specifications at a reasonable cost. In this paper, a method is described for using froth flotation and water-only cyclones to remove unreacted limestone from scrubber sludge. The water-only cyclone was found to be very effective for removing the coarser unreacted limestone, grinding ball chips, gravel, and similar coarse impurities. Froth flotation was found to remove fine unreacted limestone, with a minimum of reagent addition.

Jan 1, 1995

By Y. K. Yen, J. D. Miller, C. L. Lin

A PC image-based, on-line coarse particle size analysis system is being developed for the control of crushing and grinding circuits. Initial results had indicated that the system is accurate when tested with irregularly shaped particles which are stationary and do not overlap with each other. Now the system has been successfully tested in the dynamic mode with a moving belt conveyor. On-line size analysis for actual plant operations is discussed and includes: (1) the video system with respect to lighting and data acquisition requirements for a rapidly moving belt and, (2) image sampling, specifically the number of observations needed for accurate sampling and the total time required to perform the calculations for a representative data set.

Jan 1, 1993