Search Documents

By H. Y. Sohn, M. Pérez-Tello, J. Löttiger

An investigation of the oxidation reactions of two industrial copper mattes was performed using dflerential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) at heating rates of 20°C and 8°C/min, respectively. The temperature of incipient reaction, the total exothermic and endothermic heats of reaction and the weight change during the oxidation process were measured as functions of the oxygen concentration in the oxidizing gas, matte grade and matte particle size. The temperatures of incipient reaction measured from the DSC experiments were found to increase monotonically with all three input variables. TGA experiments showed that Cu2O and CuO CuSO4 are formed before the complete oxidation of Cu2S to CuO.

Jan 1, 2000

By d&apos, J. A. Oliveira, A. K. L. Resende, L. F. G. Assumpção, J. D. Neto

Kaolin samples from Rio Capim Resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the impurity removal process. Two coating clays and a delaminated clay were tested. The variables studied were retention time (cross-sectional velocity), magnetic-field intensity and matrix type. The feed brightness ranged, from 84.7% to 87.6% ISO, for the coating clays and ranged from 80.7% to 85.4% ISO for the delaminated clay. Using a conventional magnetic separator with an applied, field of 1.5 to 2.0 T (tesla), the brightness values were higher than 88% ISO for the unleached coating claw products and were higher than 87% ISO for the unleached delaminated product. With a maximum field intensity in the superconducting machine of 5.0T unleached brightness values higher than 88.5 % ISO were attained for both coating and delaminated clays.

Jan 1, 1997

By H. Cho, P. T. Luckie

A study was undertaken to investigate the liberation behavior of coal macerals through size reduction and density separation. It was seen that the liberation of coal macerals could be achieved by size reduction, allowing selective separation of coal organic components. However, the degree of liberation was dependent upon the comminution history. Even for the same fineness, the extent of liberation might not be the same depending on how the material was generated. The liberation of coal macerals was analyzed by examining the liberation index. It was seen that, although comminution produced fine particles enriched in inertinite (primarily fusinite and semifusinite), these particles were less liberated than coarser particles. However, the liberation of macerals increased when all the feed was ground to a finer size.

Jan 1, 1999

By R. K. Amankwah, E. K. Asiam

Changes in the thermal-oxidation behavior and other properties of gold-bearing waste activated carbon when milled in both a ball mill and a vibratory mill were investigated. It was found that significant changes occurred in the oxidation temperature of the vibration-milled waste carbon as a result of increases in surface area and mechano-chemical activation. The mechano-chemical action brought about modifications in the crystal structure of the waste carbon. As a result, the vibration-milled sample was completely oxidized at a temperature of 450°C. Thus, the study established that vibration milling is a better way of lowering the temperature of oxidation of the waste carbon. Furthermore, the gold was found to be concentrated in the ash and, when leached with cyanide for 20 hrs, the gold recoveries from a sample having a head grade of 2 kg/t was 99.5% for the vibration-milled sample and 82% for the ball-milled sample. The lower gold recovery for the ball-milled sample was attributed to sintering of the ash, which was caused by the higher temperature required for its oxidation.

Jan 1, 1997

By Edward F. Fries

Computerized, real -time monitoring had its beginning in the U.S. coal industry in the early 1970's. Over the last 10 years, developments in technology have made systems available that are capable of monitoring and controlling many mine parameters that can increase safety and production. However, situations currently exist where computerized monitoring systems are not being utilized to their fullest capability. They produce reams of printed output that are not sorted in a useful format, and human operators are not able to react fast enough in emergency situations tn tile large amount of information that the systems generate. A solution is the application of an expert system as the interface with real-time monitoring. An expert system would use an extensive knowledge base and human-type reasoning ability to make decisions on optimum strategies. Expert systems have been applied successfully to problems in other industries, and could provide significant benefits to mine information management systems. The use of an expert system with real-time mine monitoring is discussed in this paper.

Jan 1, 1986

By C. E. Capes

Reduction in the quality of resources and attendant increase in the quantities of fines to be processed present a major economic and environmental challenge for resource - based industries. It is becoming evident that agglomeration by immiscible liquid wetting will play a significant role in the treatment of these fines. Liquid phase agglomeration can be adapted to separate solids or liquids in highly divided form from liquid suspensions and emulsions. Diverse opportunities in coal fines recovery, novel fuels technologies and oily waste water treatment are cited here. The oil agglomeration of extreme fines from coal tailings, with consequent dramatic reduction in refuse for disposal, is now a commercial reality. It is suggested that this approach can serve as a prototype for the processing of extreme fines in an economical and environment ally sound manner.

Jan 1, 1989

By Jed H. (Original by) Mosgrove

Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 ma/s (9000 cfm) of air at his last open crosscut.

Jan 1, 1981

By S. R. S. Sastri, D. K. Senguta, S. K. Bhaumik, G. V. Rao

The amenability of a calcite-bearing ore to the reduction of silica to below 0.2% by physical beneficiation was studied. The objective was to use the ore as a raw material for seawater magnesia production. The ore contains complex gangue minerals such as diopside, forsterite, phlogopite, clinohumite, graphite and quartz. These contribute to around 25% acid insolubles with 6% SiO2. Reverse-flotation studies using various cationic collectors with tannin as a depressant indicated the possibility of reducing the acid insolubles to around 5%. Direct flotation of calcite with anionic sodium oleate in the presence of sodium silicate and lactic acid as a depressant indicated the possibility of reducing the acid insolubles to below 3% and the SiO2 to from 0.2% to 0.3%. Lactic acid was found to be an effective depressant of the complex gangue minerals in the ore.

Jan 1, 2000

By Michael J. Martinson, John R. Larsen, J. Warren Andrews

Measurements reported in the paper were recorded in an active Green River, Wyoming, trona mine, partly as a teaching exercise and partly to provide the mine in question with additional input data for its ventilation network program. Measurements were made: - in representative three-entry intake airways in room and pillar sub-mains; - between the lower portion of a vertical down-cast hoisting shaft and the start of an intake airway system established in a room and pillar main; - in a representative downcast section of a divided vertical shaft, and of the collar entrance loss at the top of the same compartment. Pressure differences were measured with manometers and trailing hoses, air flowrates with calibrated anemometers, and barometric pressures and wet-and dry-bulb temperatures were recorded for density determinations. Where possible, results are quoted as Atkinson friction factors, and relevant measurements are recorded in some detail to show the magnitude of fluctuations in observed pressure differences.

Jan 1, 1987

By R. A. Jankowski, R. Gong, R. Bhaskar

Full-scale laboratory studies were performed to evaluate the effect of passive barriers and spray airmovers on airflow patterns at a continuous miner face and in reducing underboom boilout and operator exposure to dust. Tasks included baseline data collection, smoke trace tests, detailed performance testing using tracer gas, and data analyses. Data collection was performed using a state-of -the-art gas analysis system and custom-developed software. The data were used to calculate operator exposure at various locations and to develop gas profile maps to analyze airflow patterns. The effects of the proposed underboom airflow modification devices on operator exposure and airflow patterns were examined. Based on the results obtained from the study, the base case condition, with no barriers, appears to result in the lowest operator exposure.

Jan 1, 1992

By R. J. Sweigard, R. V. Ramani

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. A process has been developed that will aid mine planners and public planners in the evaluation of postmining land use potential. This process involves the application of site planning principles to surface-mined land in a way that ensures productive end use of reclaimed land. The process consists of 10 basic components and is iterative in nature. Termination of the process depends on the amount of data collected and the evaluation requirements of each mining site. The analysis centers around the economic, environmental, and social impacts of the alternative land use plans.

Jan 1, 1987

By S. Saklar, i. Bayraktar

The effect of the feed size distribution on the kinetic parameters in pyrite flotation was studied. The kinetic parameters of the particular sizes were determined as a function of whether other particle sizes were present. From the data, a relation between the pyrite flotation rate and the particle size distributions was obtained. It was shown that the flotation rate constant (k) is a function of the size modulus (dt) of the Gates-Gaudin-Schuhmann distribution, and its variation may be expressed as k = a • exp(b . d,) for either individual size fractions or composite feed. Parameters a and b are dependent on the particle size distribution of the feed. Specifically, parameter a increases linearly as the distribution becomes coarser. The above relationship was also tested under conditions in which the collector (KAX) dosage was varied from 130 to 278 g/t. It was shown that the established relation was not dependent on the collector dosage.

Jan 1, 2002

By R. W. Hutson

One of the fundamental precepts of experimentation is the isolation of a single variable to quantify its individual effect. Unfortunately, the variability of natural rock joints has frustrated such isolation. This variability and the high cost of securing a large member of natural joints has lead to increasing experimental dependence on stage shearing, artificial tension fractures and/or model materials. The new apparatus described herein allows for the first time replication of real joints with field scale asperities. It employs a diamond band-saw blade with computer controlled feed table to cut joints with high precision. The feed system is capable of placement to tolerances similar to those of a high quality computer plotter. The accompanying software allows the table to cut any desired joint shape (repeating or non-repeating) within certain, over-all size limitations. Resulting joint surface dimensions and roughness as well as shear resistance indicates that the joint surfaces are reproduced with a precision similar to that possible for the control of other experimental variables such as normal and shear forces.

Jan 1, 1986

By Dwayne K. Rowlett

A lysimeter designed to measure suction and collect a pore water sample from unsaturated waste rock has been developed and its performance has been verified in two large scale column tests. The test columns were constructed to bracket the envelope of grainsize curves for waste rock from Northern Saskatchewan. The suction profile within the columns was measured under a series of infiltration rates using tensiometers and these were compared to the lysimeter readings. The rate at which pore water samples could be collected was also measured under each infiltration rate. Lysimeter measurements of suction were found to be slightly lower than the tensiometers.

Jan 1, 2000

By Norbert Patzelt, Johann Knecht, Wolfgang Baum

High pressure roll grinding (HPGR) is a mature but still expanding comminution technology. In the metals mining industry, HPGR is slowly gaining acceptance as a cost-efficient, high-throughput alternative for plant optimization. The increasing need to treat ores with progressively lower grades, complex mineralogies, refractory metal occurrence and variable rock types requires an energy-efficient comminution technology that reduces metallurgical problems inherent in conventional crushing and grinding, while stabilizing leach and flotation circuits and increasing metals extraction. This paper will summarize our latest HPGR pilot test results for gold and copper projects in the United States and South America and their confirmation through the first HPGR operation in copper mining. This paper will also stress the use of the high pressure grinding roll as a metallurgical tool. The application of HPGR for the treatment of heap leach SX-EW ores, semi-refractory gold ores, waste rock material and concentrator feeds will be illustrated.

Jan 1, 1998

By Barbara C. Williams

U.S. Bureau of Mines researchers conducted field studies at an abandoned copper-gold mine tailings impoundment. Pore water quality was analyzed in the vadose and saturated zones. Three statistical procedures were employed to summarize the variability within and between the two zones. The results indicated that linear combinations of those variables reflecting sulfide oxidation and aluminum-silicate weathering best summarized the variability in each zone, and that the zones were most different on the basis of sulfide oxidation variables. The geochemical computer code WATEQ4F was used to assess the solubility status (saturation index) of minerals. Saturation indices of sulfide oxidation and aluminum-silicate weathering minerals were different in the two zones. It was demonstrated that the statistical analyses produced similar and complementary results to the geochemical code.

Jan 1, 1992

By D. B. Dreisinger, H. J. Sohn, J. S. Sohn, G. A. Kordosky

The transport of lithium through a supported liquid membrane was studied with a mixture of D2EHPA and TBP in kerosene as a mobile carrier. In the flat- sheet supported liquid membrane(SLM) system, experiments were carried out to investigate the effects of concentration of mobile carriers in the membrane solution, hydrogen ion in the feed solution, and temperature on the transport of lithium. Experimental results agreed well with a transport model for permeating lithium across the liquid membrane. The permeation rates of lithium can be explained in terms of diffusion of a Li-complex through the membrane phase. For a practical application of an SLM method, a hollow fiber module has been used and lithium can be concentrated more than three times in 24 hours.

Jan 1, 1993

By L. Henry Smith, David C. Arthur

The Williams Mine is Canada's largest gold producer, with annual production of 14,000 Kg (450,000 ounces) from 2,300,000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs. The Mine Ventilation System is modified to include a new Vent Raise and Variable Pitch Vane-Axial Fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved. Heating costs associated with underground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, mine water and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors. System design, energy savings data and payback calculations are presented.

Jan 1, 1997

By J. West-Hansen

The problem of long-term production scheduling in an underground coal mine is approached through the concepts of sequencing theory. Based on a typical layout of mining sections, the principles for the approach are: 1. The definition of mining sections as jobs, and mining methods as machines. 2. The reduction of the overall mining activity to the general problem of nonpreemptive scheduling of precedence related jobs on parallel machines. 3. The simplification of the layout to a general type directed network with the nodes representing jobs and the arcs representing precedence relations. 4. The determination of a feasible and near-optimal job schedule given the objective of maximizing the total net present value of the jobs. A general scheduling heuristic is being developed for implementation on an IBM personal computer (PC) as part of an interactive computer system for long-term production planning.

Jan 1, 1986

By D. Tao, B. K. Parekh

Fine coal particles are difficult to separate effectively from liquids or other solids. Ultrasonic energy may be used to enhance the efficiency of the conventional fine-particle separation processes widely used in the coal and mineral industries. Flotation, settling and dewatering tests were conducted using several fine coal samples to study the effects of ultrasonic treatment on these processes. Process variables such as particle size, ultrasonic treatment time and solids concentration were investigated for their impacts on ultrasonic treatment effectiveness. The results obtained from this study showed that ultrasonic treatment is an effective approach for enhancing solid/solid separation in flotation and solid/liquid separation in sedimentation and dewatering of fine coal. SEM microphotographs demonstrate that ultrasonics cleaned particle surfaces, which is, in part, responsible for the observed improvement in fine coal separation processes.

Jan 1, 2000