Search Documents

By Gabriel Esterhuizen

Underground stone mines in the United States make use of the room-and-pillar method of mining. A prerequisite for a safe working environment is that the pillars should adequately support the overburden and the pillar ribs and rooms should remain stable during mining. At present pillar dimensions are either based on experience at neighboring mines or on strength equations that were developed for metal or non-metal mines. This paper presents a pillar design methodology that was developed from a study of pillar performance in operating stone mines. Data were collected that describe the rock mass quality, pillar conditions, mining dimensions and intact rock strength. The results showed that current mining practices have resulted in generally stable pillar layouts with no recent cases of extensive pillar collapses. However, a small number of single failed or failing pillars were observed in otherwise stable layouts. Numerical analyses were used to supplement the observations and develop a pillar strength equation that describes the stable and small number of failed pillars observed. The developed strength equation can be used to design stable pillar layouts provided the factor of safety is greater than 1.8 and the width-to-height ratio of the pillars is greater than 0.8. The paper concludes with guidelines for applying the developed equation and selecting appropriate input parameters.

Jan 1, 2008

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By Frank Chase

Longwall mining has gained the reputation as being the safest extraction method in underground coal mines. However, one of the most difficult tasks associated with longwall mining is moving the face once a panel is completed. Based on Mine Safety and Health Administration (MSHA) fatality reports since 1996, longwall face recovery operations have claimed the lives of 5 U.S. miners and have resulted in numerous injuries. Recovery operations can be hazardous because they involve moving large pieces of equipment in very confined spaces. They are also conducted in highly stressed ground conditions due to front abutment loads generated by panel extraction. Shield removal is the most hazardous operation during face recovery because miners are constantly exposed to the unpredictable gob edge. To protect the miners, one or more walking shields, cribbing and/or other supplemental roof and standing supports are typically employed as breaker line supports as each shield is removed. At the Harris No. 1 Mine in southern WV, mobile roof supports (MRS?s) have been used in lieu of traditional walking shields on 17 face moves since 1997. MRS?s are shield-like support units mounted on crawler tracks and are commonly used during room-and-pillar retreat mining operations. For longwall recovery, the two biggest advantages that MRS?s have over traditional walking shields are that they are remotely controlled and are highly maneuverable. MRS?s have contributed to safer shield recovery and shorter move times at the Harris No. 1 Mine. This paper will address both the safety and the operational issues associated with MRS usage during shield recovery. It will also discuss new developments, including the use of the inherently safer battery powered MRS?s, which have been recently certified by the Mine Safety and Health Administration.

Jan 1, 2007

By A. Wahab Khair

Coal mining has evolved into extensive use of continuous mining machines for development and production. This has resulted in an increase in dependence on the versatile continuous miners. The present-day continuous miners are powerful in terms of rated power but are still plagued by wear of bits which hinders development and production as the bits have to be continuously changed at regular intervals. Previous attempts to analyze bit wear has been either restricted to the theoretical approach and or laboratory testing. This paper discusses about the overall aspect of bit and drum design for different conditions. Using the laboratory model set up, numerical models and field testing, a new bit and drum design was analyzed to evaluate their performance under different conditions. The results proved that a newer bit design and drum design were successful in limiting the amount of wear as well as improving the performance of the continuous miner and production.

Jan 1, 2008

By Da Zhao Gu

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

By Karsten Zimmermann

Surface deformation monitoring is required all over the mining industry. For example oil and gas companies need this information to support exploration and production activities and to detect impacts from surface subsidence of existing hydrocarbon fields. Also opencast mines require large area information of subsidence due to dewatering of the overburden. Because of this, a lot of surface deformations measurements with GPS or traditional geodetic measurement techniques have been conduced during the last decades. This paper presents the actual capabilities to analyze GPS data using the state of the art Bernese GPS Software for GPS post processing. A new way of monitoring subsidence is a combination of GPS and satellite InSAR data. Considering this it is hoped that a combined strategy will permit receiving overall more information by integrating high point density of InSAR and accuracy of GPS. DMT is one of the leading actors on GPS services especially for monitoring surface movements from underground activities e.g. mining, water pumping or oil and gas exploitation. The paper will discuss preferences and problems of this approach on results of a current project of DMT.

Jan 1, 2008

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012

By Axel Preusse

For the last 150 years, subsidence damage to the surface has been an unavoidable phenomenon associated with underground coal mining. In particular, the mechanization of mining methods in multiple seam mining and the concentration of mining activities in densely populated European metropolitan areas (e.g., Ruhr, Upper Silesian industrial region) have led to mining having a very strong influence on the earth?s surface. In both these regions, surface subsidence of more than 20m has been reported up to now in comparison to the original state. Underground coal mining in these regions strongly impairs all kinds of surface use, such as urban and industrial development, infrastructure (roads, waterways, and railways) and pipelines?without restricting the functionality of those objects to a greater extent. Demanding and, in some cases, globally unique engineering solutions have been developed and implemented for this purpose. The previously mentioned mining and industrial regions are still very strongly characterized by the (increasingly declining) coal industry and will remain dependent to a large extent and for an indefinite period on artificial drainage measures because subsidence that has already occurred is irreversible. This paper will primarily discuss the prediction of subsidence that is caused by intensive multiple seam mining and its influence on surface objects (e.g., underground pipelines). However, an approach for predicting ground uplifts due to rising mine water as a consequence of mine closures will also be described.

Jan 1, 2012

By Frank E. Chase

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that "critical" sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

Jan 1, 2005

By Lixun Kang

Bedded structure is the characteristics of coal measures strata. Bedding planes, coal streaks and soft rock bands existing in roof strata destroyed its continuity in the direction perpendicular to the coal seams. The statistics from a large number of long wall faces in which serious roof fall accidents occurred in Datong coal mining area suggest that beddings planes, coal streaks, soft rock bands, especially the first layer thickness of immediate roof have a great influence on its stability. As the first layer thickness increases, the probability of serious roof fall accidents decreases. Based on the investigations finite element method is used to analyze stress and displacement in the first layer of immediate roof. The results indicate that the thicker the first layer is, the less the roof convergence in the unsupported area is. Stress and strain features in stratified immediate roof are quite different f7om those in non- bedded immediate roof. In stratified immediate roof, every stratum has each own tensile zone in the upper portion and compressive zone in the lower portion, while tensile zone in the first layer is less, the tensile stress is the greatest.

Jan 1, 2005

By Stephen J. Harven

Geologic conditions in eight northern operating sections of Jane Mine, Keystone Coal Mining Complex. Armstrong County, Pennsylvania are defined by utilizing drillhole data and underground geologic mapping. Three of the eight sections are experiencing difficult mining conditions in the Shelocta "0" coal seam (formerly the Lower Freeport). The five remaining productive sections will exhaust their reserves within one year. Coordinating mine planning with future production levels is aided by indicating areas that appear favorable and lack the geologic conditions that cause difficult mining. Roof rock 1 ithologies, lithologic variations in and below the floor, jointing, overburden thickness, coal splits, paleochannels. and clay veins are the principal geologic factors believed to influence mining conditions in Jane Mine. Careful definition of each cause allows for a reasonable assessment of future mining conditions.

Jan 1, 1987

By Daniel W. Su

This paper presents the results of a detailed geotechnical study on the potential multiple seam interaction between the No. 2 Gas (upper) and the Powellton seams, which are separated by an average interburden of 45 ft. The interburden consists of 4 ft of clay shale below the No. 2 Gas seam, 38 ft of massive sandstone, and 3 ft of shale above the Powellton seam. The No. 2 Gas seam was mined about 60 years ago, and many water-pooled areas were projected to be present. The deepest overburden over the No. 2 Gas seam is about 750 ft. To evaluate the potential interaction between the two mine works and to determine the pillar safety factor, Analysis of Multiple Seam Stability (AMSS) software was initially used to determine pillar dimensions to obtain a minimum safety factor of 2.0 for areas under pooled water, as well as a minimum safety factor of 1.5 for areas not under pooled water. Furthermore, to assess the quality of the interburden rock strata, two surface core holes were drilled, and rock cores were tested in the laboratory for their strength and elastic moduli. Using the experimentally determined strengths and moduli as part of the input parameters, the RocScience Phase2 finite element program was employed to model the stress field scenarios and estimate the safety factors of the interburden rock strata before and after Powellton seam mining. The pillar safety factors derived from the Phase2 analysis were in excellent agreement with those obtained from the AMSS analysis. Phase2 results also predicted that the effect of the Powellton seam mining, first mining only, would reach a maximum of 19 ft above the Powellton seam, which led to the proposal of drilling 25-ft deep test holes to detect water, instead of the 45-ft deep test holes mandated by MSHA. The proposed test-hole height was accepted by both Mine Safety and Health Administration (MSHA) District 4 and the state of West Virginia. Mining of the Powellton coal seam commenced in February 2011 and continued for eight months. To date, no 25-ft deep hole has encountered water under the water-pooled zone, which validates the RocScience Phase2 finite element analysis. Also, inmine observation of excellent pillar stability and roof condition confirms the validity of the AMSS analysis.

Jan 1, 2012

By Michael Gauna, Christopher Mark

"For decades, pillar recovery accounted for a quarter of all roof fall fatalities in underground coal mines. Studies showed that a miner on a pillar recovery section was at least three times more likely to be killed by a roof fall than other coal miners. Since 2007, however, there has been just one fatal roof fall on a pillar line. This paper describes the process that resulted in this historic achievement. It covers both the key research findings and the ways in which those insights, beginning in the early 2000s, were implemented in mining practice.One key finding was that safe pillar recovery requires both global and local stability. Global stability is addressed primarily through proper pillar design, and became a major focus after the 2007 Crandall Canyon mine disaster. But the most significant improvements resulted from detailed studies that showed that local stability, defined as roof control in the immediate work area, could be achieved with three interventions:• Leaving an engineered final stump, rather than extracting the entire pillar;• Enhancing roof bolt support, particularly in intersections, and• Increasing the use of Mobile Roof Supports (MRS)A final component was an emphasis on better management of pillar recovery operations. This included a focus on worker positioning, as well as on the pillar and lift sequences, MRS operations, and hazard identification. As retreat mines have incorporated these elements into their Roof Control Plans, it has become clear that pillar recovery is not ""inherently unsafe.""The paper concludes with a discussion of the challenges that remain, including the problems of rib falls and coal bursts.INTRODUCTIONPillar recovery has always been an integral part of underground coal mining in the US. When room-and-pillar methods are employed, large blocks of coal in the form of pillars are initially left in place to support the weight of the overburden. Unless these pillars are subsequently recovered, the coal they contain will never be mined."

Jan 1, 2016

By Bill Kyslinger

In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Boart Longyear Poland and KGHM, J. H. Fletcher & Company was tasked to design and manufacture a single-boom, single operator drill module for installation of 1.2 meter expansion bolt in a 1.6 meter height mine. The objective was to produce a machine to provide ergonomic improvements for the operator while working in the mine environment. This dictated the requirement for a small easily controlled, maintenance friendly design with a remote operator?s control station. The selected design method was to use starter and finisher drill steels. This combination, requiring a number of mechanized machine motions, provides the ability to drill the required depth in the specified mine height. To accomplish the task from a remote location, a conscious decision was made to employ current technology in the form of small pressure compensated hydraulics and electronic controls. The result of the design method is a modular assembly with each sub-component designed to be replaceable and adjustable independently from other machine components. The low profile remote roof bolting module is made up of six major sub-components. Each major component is painted a different color to help the operator make the visual connection from the drill module to the operator?s control/display monitor. The Stabilizer (White) secures the module between the mine top and floor. The Drillhead (Orange) produces the drilling rotation and torque but also must slide out of position to allow the machine to manipulate the drill consumables. The Drill Steel Carousel (Blue) holds and indexes the starter and finisher steel from position to position. The Manipulator Arm (Green) moves and guides the drill steels and drill consumables from position to position during installation. The Roof Reference Guide (Yellow) locates the mine roof and guides the drill steels and drill consumables into position. The Linear Bolt Carousel (Purple) holds the drill consumables. The low profile remote roof bolting module allows the operator to drill and install a roof bolt manually or automatically with the push of a button. This design substantially reduces the operator?s exposure in the mine environment, as well as inherent pinch points and rotary hazards. Positioning the operator safely in the confines of the air conditioned cab.

Jan 1, 2006

By Gabriel Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

Jan 1, 2007

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ? Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions ? became the post-event conditions.Search for evidence that either denies or supports the various ? hypotheses.Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By Yi Luo

The efforts to mitigate longwall subsidence influences on various residential and farming structures by many coal mining companies have been successful in the recent years (Luo, et al, 2003). The successes were largely dependent on the accurate subsidence predictions, correct assessments of potential influences, appropriate design and implementation of the mitigation measures. However, such efforts for protecting large industrial structures are still very rare. In this paper, the successful assessment and mitigation of the subsidence influences associated with a very intensive dynamic longwall subsidence process on a large workshop are presented.

Jan 1, 2005

By Takashi Sasaoka

Chain Conveyor Cutter (CCC) is a chainsaw-type machine and originally developed for the construction of underground walls and/or ground improvements. CCC was developed from the accumulated technology of coal mining, combining the cutting technology of a shearer and the fuctions of chain conveyor. The CCC can cut harder soils and soft rocks, and vertically mixes the cut soils/rocks with cementing material selected through the discharging port installed at the bottom of the machine. In Indonesia, highwall mining trials have already been conducted in several coal mines. However, full-scale and regular operations have not been done yet due to the ground and machine control issues from their geological conditions. In order to overcome these problems, the application of CCC to highwall mining systems was proposed, and its applicability and technical issues to be solved were investigated in this research. This paper discribes the characteristics of CCC system and discusses the application of CCC to highwall mining systems.

Jan 1, 2012

By Takashi Sasaoka

Indonesia is the second largest coal exporter to Japan, accounting for about 30 M tons annually. They produced about 150 M tons in 2005, over 99% of which being from open-cut mines [1]. However, the conditions of surface mining are becoming worse each year: the stripping ratio is increasing, approaching the economic ratio and the infrastructure for coal transportation from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. At present, there are only five small underground mines, three of which are old and the other two have only recently begun mining operations [2]. However, severe ground control problems have been occurring regularly, roof falls in particular. At a new mine developed from the highwall, a large bolted roof fall occurred at the heading face, killing two miners. Unfortunately, mining engineers and/or miners in this mine do not have a lot of experiences, expertise and know-how concerning the operations of underground coal mines. Since 2001, Japan has started a ?five-year plan for coal technology transfer? to fill Japan?s moral obligation as the largest coal importer in the world. The research team for this accident was organized and the on-site investigation was conducted in order to find the cause of this accident and make the solution. This paper describes the roof fall accident at the mine, discusses its causes and mechanism and suggests the introduction of some techniques for improving the current support system considering the strata and stress conditions by means of field observation and finite element modeling.

Jan 1, 2007