Search Documents

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By D. W. Evans

Mine subsidence problems due to coal extraction have occurred in a number of areas throughout the United States. Depending on the local geology, the depth of the mined seam, the type of mining method employed for extraction, and other related factors, subsidence can result in anywhere from slight displacements to a total loss of ground. These conditions can have serious consequences on the health and safety of the people living above the mined areas. A number of methods exist to provide support for the ground overlying mines. All of these methods employ some mechanism for providing additional support to either the roof of the mine or the sides of the pillars. Since failure usually occurs due to overburden stresses which are transmitted to the roof and pillars, these methods employ techniques to counteract stresses induced due to the coal extraction. The applicability of any particular method will depend on the availability of backfill material, the areal extent of the affected area, and of course, the cost. The primary use of coal ash for subsidence control has been as a backfill material for the stabilization of large areas. Large scale backfilling projects for subsidence control have been performed in Rock Springs, Wyoming, Wilkes-Barre and Scranton, Pennsylvania, and in Fairmont, West Virginia. Some of these projects have utilized sand, as well as, coal ash as backfill material. Much of the backfilling work performed in the United States has been done in an effort to control mine subsidence in abandoned mines. South Africa, on the other hand, has used backfilling extensively both for ash disposal and to increase extraction in active mines. The utilization of repetitive fill and mine techniques has resulted in extraction increases of as much as eight percent in shallow mines and as much as twelve percent in deep mines.(1) The coal ash injection system which can be used for backfilling depends largely upon whether the mine voids are dry or submerged. For dry mines, hydraulic or pneumatic conveyance systems can be used, while submerged mines are limited to backfilling by hydraulic methods. The use of coal ash as a backfill material has a number of advantages, such as: 1. Coal ash is available in areas throughout the United States and in many instances is conveniently located near areas requiring backfilling. 2. Coal ash is available in significant quantities since many coals when burned will result in about 15 to 30 percent ash by weight. 3. Coal ash as backfill is, in many instances, the most economical alternative fill material. Due to the costs associated with above ground disposal, power companies will often times give the material away to lower their overall operating expenses. 4. Coal ash is usually pozzolanic in nature, that is, this material results in cementitious bonding within the backfilled matrix of material.

Jan 1, 1982

By D. W. H. Su

Following a roof fall in the B12 headgate of a CONSOL Pennsylvania Coal Company (CCPC) underground coal mine in February 1998, CONSOL R&D and Exploration initiated an underground roof geology reconnaissance program along the B13 and B14 developments to define potential roof instability areas and to recommend appropriate supplemental headgate support. This reconnaissance program revealed the presence of a thick, massive Pittsburgh sandstone channel overlying the B13 and B14 panels. Surface and underground core holes confirmed the close proximity and the very massive, nonlaminated nature of the sandstone. To mitigate anticipated adverse conditions at the B 13 and B 14 longwall faces due to delayed caving of the massive sandstone behind the shields, a task force consisting of Operations, Exploration, and R&D personnel was formed in May 1998. Several operational adjustments were made by mine management, including repairing damaged lemniscate links, maintaining immediate forward shield support, and implementing measures recommended by the task force intended to boost the shield set load density at the face. After reviewing available geotcchnical information, the task force also recommended fracing of the massive sandstone over the B13 and B14 panels to enhance caving characteristics and further reduce the bending-induced stresses in the sandstone near the face. Horizontal fracs were created at a horizon about 25 feet above the Pittsburgh seam main bench over the two panels in June and November 1998, respectively. To evaluate the effect of sandstone fracing and operational adjustments on the bending-induced stresses in the sandstone, three finite element models were constructed and analyzed. Results from the finite element analyses indicate that one horizontal frac, 25 feet above the Pittsburgh seam, would reduce the bending-induced stresses in the sandstone by approximately 50 percent, maintaining them at a level below the ultimate strength of the sandstone. Operational adjustments to increase the support set load density and support stiffness could reduce the bending-induced stresses in the sandstone by a maximum of an additional 10 percent. Shield pressure monitoring at the B14 midface confirmed the presence of a lower roof pressure zone inby and outby the 1314 frac holes. This lower face pressure significantly contributed to improving the B13 and B14 longwall productivity and safety. The total production downtime due to bad top at the B 12 face within the interval of channel influence was 30,600 minutes compared to about 3,500 minutes each for the B13 and B14 faces. The average longwall advance per machine shift for the B13 and B14 faces within the channel was about 70 percent higher than that for the B 12 face.

Jan 1, 2001

By Jessica M. Wempen, William G. Pariseau, Michael K. McCarter

"Quantitative analysis of mine-wide subsidence at the kilometer scale and details of stress distribution about an advancing longwall face are estimated using an adaptation of the finite element method. The method is well suited to the tasks at hand. For greater realism, variability of strata properties is taken into account as are the effects of joints and cleats on elastic moduli and strengths. Evolution of pillar stress and entry closure remote from the face is readily quantified in a series of analyses that simulate face advance. Computed results compare favorably with the evolution of closure measurements about an instrumented pillar in a two-entry headgate. The appropriateness of the finite element method is confirmed. This method is based on first principles that avoid empirical schemes of uncertain applicability and numerical models “calibrated” by fitting computer output to mine measurements.INTRODUCTIONMine-induced seismicity is intimately related to strata mechanics associated with longwall coal mining and room and pillar mining, as well. Strata deformed beyond an elastic limit often tend to fail rapidly by brittle fracture and, thus, to emit acoustic signals in the form of elastic waves. Understanding the induced seismicity in coal mining offers the potential for early warning of hazardous conditions. Many years of experience with seismic phenomena associated with hardrock mining suggest considerable complexity should be expected. However, recent coal mine studies (Pariseau, 2014; Pariseau, 2015; Pariseau and McCarter, 2015; Pariseau and McCarter, 2016) have shown high correlations of seismicity with element failures in finite element simulations. The main lesson learned from these studies is one elaborated by Iannacchione et al (2005); deviation from normal activity is an early warning of ground control difficulty. For example, an abrupt increase in seismic event rate, or equivalently, an increase in element failure in finite element simulation of panel advance, is a cautionary indication for ground control. Present and past study results demonstrate the effectiveness of finite element simulations for mine design and early detection of potential ground control issues."

Jan 1, 2018

By John Stankus

Seam interaction in multiple seam mining has significant effect on entry stability. The remaining pillar in an old working usually creates a high stress concentration zone while the gob creates a stress release zone. A good panel layout should take advantage of the stress release effect created by old workings. This paper presents two case studies of multiple seam mining. The Jennmar Finite Element Analysis System (JFEA) is utilized to analyze the seam interaction effect and identify the mess concentration and relief zones Panel layouts are designed bad on the results of the finite element analysis Appropriate roof support system are also designed for different seam interaction areas.

Jan 1, 1999

By G. C. Xiao

A database, incorporating historical data from British mines, to study the factors affecting inflows from proximate aquifers into longwall workings, showed that a main casual factor was the immediate roof strata lithology. When this comprised principally stronger sandstone, there was a tendency for periodic inrushes associated with face weighting. This phenomenon is explained by the collection of water in bed sepa¬ration cavities, where free water connected to a high pressure head aquifer source, may be trapped.

Jan 1, 1990

By Fangting Dong

The broken rock zone (BRZ) and the tunnel support theory are investigated. The relationship between the BRZ and the related factors, the interaction between the BRZ and supports, and the function of supports are analyzed in detail based on the authors' underground observations and model taste. A summary of the application of the BRZ theory in the past is also presented.

Jan 1, 1988

By M Nombe

Based on the analysis of a case study at POWELTON No.2 MINE, it was determined that mine stability problems had occurred due to floor softening. A fireclay (underclay) layer in the immediate floor was softening after coal extraction and failing under pillars load. The thickness of soft floor was considered as the governing factor in the determination of the magnitude of floor displacement. The effect of floor thickness on floor displacement was evaluated by creating seven models that were input into the LAMODEL program. The properties of the soft floor were determined from a bearing capacity test performed in the Mains close to the area where mine stability problems had occurred. Moisture increase was considered in the reduction of floor bearing strength. Various strain-softening properties were allocated to the materials representing the soft floor. The LOW GAP POWELTON No.2 MINE was modeled and LAMODEL program was used to determine stress and convergence on both the coal seam and the fireclay seam. The results of critical stress and convergence obtained from modeling were compared with the actual floor failure area in the mine.

Jan 1, 2002

By P. A. Gray

Artificial ground support has developed into a relined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bait is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By K. Haramy

Coal mine bursts or bumps involve the violent, rapid failure of coal and rock in or around a mine excavation. Failure is normally associated with high stress and brittle or brittle-elastic materials; in coal mining, bursting may also be associated with desorbing gas, and this type of failure is termed an outburst. This paper discusses factors affecting coal mine bursts and several methods to predict bursts, including microgravity, microseismic, rheological, rebound, and drilling-yield methods. Methods to avoid burst conditions using volley firing, hydraulic fracturing, and auger drilling are also discussed. A case study is presented in which the redistribution of stresses and displacements was found to be associated with a burst at a deep longwall coal mine. The research showed that stresses are redistributed following the burst.

Jan 1, 1984

By Erdal Unal

In underground mining today, safety and economical aspects demand a better understanding of the rock-mass conditions, particularly for design of underground mine openings excavated in weak and stratified rock mass. The rock mass classification systems, in essence, are empirical approaches utilized during preliminary design stage. These systems have been developed for specific purposes and rock mass types, therefore, direct utilization of the classification systems in their original form, for characterization of complex rock-mass conditions is not always possible. This is probably one of the main reasons why designers continue to originate new systems, or modify and extend the ones already existing. RMR and Q systems, for example, although widely used in mining and tunnelling, can not fully describe the specifications of the weak, stratified and flay bearing rock mass. Consequently, the engineering applications that would be carried out based on original RMR and Q ratings could be inadequate for making design decisions even during the preliminary design stage.

Jan 1, 1990

By Susan Robertson

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100% can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

Jan 1, 2002

By Gregory Molinda

Groundfalls are much more likely to occur in coal mine intersections than in entries. NIOSH is using the experience of U.S. coal mines to determine the factors which influence intersection instability and provide guidelines for the safe excavation and support of intersections. Detailed field investigations have resulted in a database of U.S. coal mines containing 12 mines and 639 roof falls so far. By using the roof fall rate as the outcome variable, correlations between roof geology (CMRR), intersection span, and roof support have been established. Case studies have indicated that replacing 3 way intersections with 4-way intersections may not reduce the total number of roof falls. Additionally, the size of intersection spans tend to decrease with lower (weaker) CMRR. Protocols have been established for the collections of roof bolt parameters. The performance of individual roof bolts can now be tracked with roof fall rate.

Jan 1, 1998

By A. Grenoble

The mining of seams in close proximity can greatly accentuate interaction problems. At distances of less than 110 feet vertically interaction can occur for both over and under mining. Research into ground control problems resulting from undermining a previously mined seam has been carried out using finite element and body-loaded photoelastic modeling methods in conjunction with numerous case studies. Analysis of field data was used to validate and expand the model results. Research findings demonstrate situations under which the worst ground control conditions can be expected to occur for a specified geologic environment, depth, innerburden spacing and mining geometry. Special emphasis has been placed on the effects of pillar load transfer on the lower seam in terms of pillar and floor stability and roof control. Roof and floor condition indexes are used to summarize structural and lithologic conditions in the affected seam. The effects of joint orientation and continuity are incorporated in the analysis and the research results have been compiled into a software package for application by the field engineer.

Jan 1, 1984

By Kot F. Unrug

The shale response to moisture changes and the major finding of the appropriate research concerning this subject are briefly reported in this paper. Also described are mine ambient atmospheric conditions which are responsible for moisture changes in mines. The need for a quantitative measure of the weathering potential of roof. rock is demonstrated in relation to its influence on safety and the potential for increasing the cost of mine operations. The weatherability test presented in this paper has been developed and used in many mines. It imitates the natural process in a mine by subjecting the rock sample to alternating wet and dry cycles. The natural changes are thus accelerated, but are similar to the natural conditions to which the surrounding excavation rock will be exposed. The measure of the weatherability index is the percentage of the initial sample mass remaining after the test as the largest fragment of the sample. Thus, the index changes, from 100% for rock affected by moisture changes which disintegrates completely, to 0% for rock totally unaffected. In this paper, the apparatus and testing procedures are described. Also presented are examples of test results. with a discussion of the design implication to he considered by mine planners.

Jan 1, 1997

By Soheil Bahrampour

Development of measurement while drilling (MWD) systems for ground control applications in mining applications has recently been an active research topic. The main goal is to utilize the drilling information for characterizing the ground condition. Such characterization is the key to the accurate and efficient mapping of hazards and proper planning of ground support. However, most of the existing drilling units and measurement while drilling systems are mainly developed for joints and voids detection, and much less research is done to estimate rock strength. This paper focuses on rock classification based on estimated strength from the drilling data. For this purpose, data from J.H. Fletcher roof bolters instrumented with the vibration and acoustic sensors as well as torque, thrust, penetration rate, RPM and position signals is used. All the available data was utilized for rock classification using pattern recognition algorithms. The algorithms were developed based on data from drilling, and into three different rock types. The classification is performed using a simple feature extraction algorithm with a well-known pattern recognition algorithm. The results demonstrate the suitability of the proposed algorithms in identifying the rock types based on their strength properties, which can be adopted in measurement while drilling systems.

Jan 1, 2014

By Brian White

Two examples of en echelon mining-induced fractures seen in hard¬rock mines provided a basis for inferring that fracture zones and bedding plane separations immediately surrounding mine openings are promoted by oblique shear into the openings. It is hypothesized that initial fractures or separations form at the comers of openings as a result of high stress and physical constraint on the rock's ability to deform elastically toward the opening. These conditions result in a locally preferred direction of shearing. The shearing, in turn, generates tensile stress that initiates a progression of systematically offset fractures approximately parallel to the direction of greatest compressive stress. The fractures or bedding separations create tabular rock layers that amplify shearing displacement through bending and dilation. Such shearing effectively reduces and redistributes the compressive stress, but significant dilation is an inevitable consequence. The combination of dilation and shearing and the progressive development of fracture zones have important implications with respect to ground support. The concept of mining-induced fractures forming as a result of shear is illustrated by two examples from coal mines. First, frac¬tures seen at longwall faces probably result from shear associated with subsidence. The fracture zone that develops approximates or possibly defines the draw angle of subsidence. As the face advances, fractures extend downward along the lower edge of the fracture zone, while upper extensions of the fractures are pressed closed. Fracture zones in entry roofs provide a second practical example. Here, mining-induced fractures typically follow bedding planes. The shear zone model suggests that the first bedding separations develop near the edges of the roof and successive separations progress upward and toward the center. However, if the direction of greatest stress is inclined with respect to the roof, a fracture or bedding separation zone may propagate from one side only and also extend higher. Because coal ahead of the face provides some support against lateral shear deformation, bedding separation is inhibited near the face. Rock bolts installed close to the face ultimately become more strained and bent than bolts installed a few meters from the face, and bolts installed through the more remote part of a separation zone may ultimately experience the greatest tensile and bending strains. This model is supported by field data documenting progressive bolt failures that rapidly propagated downward across the roof during face advance.

Jan 1, 2002

By Eric Keller, Jamal Rostami, Wenpeng Liu

"Roof and rib instability is an important issue in underground mining. To optimize ground support design, enhance ground stability, and reduce the possibility of roof or rib failure with minimal use of artificial ground support, it is essential to have an accurate understanding of ground conditions. This includes the location of voids, cracks, and discontinuities, as well as information about the different strata in the immediate roof. This paper briefly introduces ongoing research on void detection by using the roof bolter feed and rotation pressure. The goal of this project is to improve the sensitivity of detection programs to locate smaller joints and reduce the number of false alarms. This paper has presented a brief review of the testing procedures, data analysis, logic, and algorithms used for void detection. In addition, this paper has discussed the results of preliminary laboratory tests and statistical analysis of the data from these two drilling parameters used for void detection.INTRODUCTIONRoof falls are one of the most serious and frequent accidents in underground mining. Each year, personnel are injured or killed because of roof falls. Equipment can also be damaged when this occurs. According to Mine Safety and Health Administration statistics collected from 1999 to 2008, ground falls were the largest cause of fatal accidents in underground coal mining, causing around 40% of all fatalities (NIOSH, 2015a). Out of 8 to 10 fatalities and over 800 injuries are recorded each year in underground mines, there are nearly 2,000 reportable non-injury ground falls every year (NIOSH, 2015b).Certain features in the ground, such as voids, cracks, and discontinuities, are significant factors that cause roof support failures and roof fall accidents. Currently, several manufacturers provide smart roof bolters with limited capabilities for void detection. While successful in many instances, in laboratory experiments, the existing void detection systems have limited success in detecting void openings that are less than 1/8 inch This limited success was observed in testing concrete blocks with gaps in between, simulating a rock medium with voids. Detection programs have missed some voids, while, in some cases, they have shown false detection. These algorithms need to be more accurate in sensing voids to improve the capabilities of these programs."

Jan 1, 2016

By Jimin Su, Enguang Zhu, Kangning Zhang, Yang Li

"The effect of interburden on overlying strata movement during the mining of a lower group coal seam is still a challenge in China. Based on the multiple coal seams in western China, numerical simulation and field tests are applied to study the interburden and overburden movement during the undermining process. This study focuses on the impact of the thickness and structure of the interburden, the proportion of hard rock, and the ratio of the overburden thickness to interburden thickness (OB/IB). In this paper, four typical underground coal mines are simulated for lower seam longwall mining with different interburden parameters. The results indicate that the ratio of the overburden thickness to the interburden thickness is not the dominant actor for multiple seam longwall mining, especially in the mines in western China,which feature shallow depth. The thick and hard interburden could strongly affect the lower coal seam mining process. INTRODUCTION The project background is based on four typical underground coal mines in western China.The information on the overburden and interburden is shown in Table 1. Different overburden to interburden thickness (OB/IB) (Ellenberger, 2009) values of the four coal mines are also studied: 6.2 in Bulianta coal mine, 7.2 in Kaida coal mine, 8.2 in Shigetai coal mine, and 9.4 in Halagou coal mine. The proportions of hard rock in the interburden of the four coal mines are also different: 0% in Kaida coal mine, 70% in Shigetai coal mine, 80% in Bulianta coal mine, and 100% in Halagou coal mine. To be specific: the thickness of interburden are listed as follows: 7m in Halagou coal mine, 6m in Kaida coal mine, 10m in Shigetai coal mine, 28m in Bulianta coal mine. The depth of the upper coal seam are: 66m in Halagou coal mine, 54m in Kaida coal mine, 79m in Shigetai coal mine, 182m in Bulianta coal mine. NUMERICAL SIMULATION UDEC 4.0 is applied in this paper to analyse the overlying strata movement and the interburden failure.(Liu, 2007) This is based on mining in the lower coal seam under the mined-out upper coal seam (Majdi, 2012, Morsy, 2006)."

Jan 1, 2017

By Thomas M. Barczak

Roof support systems are necessary to provide stable mine openings and much research has been conducted to design a variety of roof support systems that will function in various manners to ensure that stable ground conditions are achieved. Despite these advancements in technology, mistakes continue to be made in the evaluation and/or installation that significantly degrade the support capability or lead to erroneous determinations of support expectations. The purpose of this paper is to discuss misconceptions about how roof supports perform and factors that impact their performance. The goal is to present practical information that will assist mine operators and engineers in selecting, installing, and evaluating roof support systems properly, and help them to avoid mistakes that can lead to erroneous expectations and potentially catastrophic results that may lead to roof falls. The paper is limited to a discussion of secondary roof support systems and powered roof supports such as longwall shields.

Jan 1, 2001