Search Documents

By Asmaa Yassien

Finite element models were developed to study the effect of tensioned and fully-grouted bolts on the stability of the mine opening in a three-entry development system using a typical geological column for the Pittsburgh Coal Seam. The models were used to study the effect of each bolt type on the stress distribution in the immediate roof, yield zone development and the vertical deformations. Comparison of all of those features show that the effect of a tensioned bolt on the stress distribution in the immediate roof is restricted to limited areas, whereas the fully-grouted bolt has a much wider effect on the stress distribution. Both types of bolts can reduce the yielding and deformation in the immediate roof to different degrees. The fully-grouted bolt reduces the sliding along the bedding plane more than the tensioned bolt. Both types of bolts were able to maintain the bedding planes without separation. The induced forces in both types of bolts are analyzed. A rapid increase in the shear force and bending moment occurred in the fully¬grouted bolt due to the relative motion of bedding planes.

Jan 1, 2002

By Bruce W. Jack

An extensive underground roof-monitoring program was conducted in order to determine the roof strata behavior under various conditions. In total 29 sites at 5 different collieries were monitored using the sonic probe extensometer. Results showed that, in drill and blast sections, there are often pre-existing openings in the roof prior to the installation of the support. An estimated 42 per cent of the total roof displacement monitored in drill and blast sections took place prior to the installation of support. A comparison between roadways and intersections indicated that, for a 40 per cent increase in the span, taken across the diagonal of art intersection, relative to the roadway width, the magnitude of the displacement in the roof increased by a factor of 3. Total displacements measured were relatively small, only 2 reaching double figures of 12 mm. The remainder were all less than 7 mm. The results also showed no evidence of a substantial increase in the height of the bed separated, potentially unstable roof strata, as is the case in the high horizontal stress-driven beam-buckling mechanism experienced in for instance some Australian coal nines. Therefore, it was concluded that, in South African collieries, the effects of horizontal stresses is generally relatively small compared to overseas collieries.

Jan 1, 2000

By George S. Kalamaras

Coal strata strength is included as a vague term in most of the pillar design formulas, either as a questionable fraction of the intact coal strength or a size-dependent relationship for scaling down a laboratory value to the in situ strength. In order to introduce a coal mass strength criterion which would be compatible with current design trends, the Rock Mass Rating (RMR) system was revised to incorporate factors governing coal seam behavior under load. A number of adjustment factors have been proposed but, the most significant change, is the introduction of a parameter representing the heterogeneity of the seam. When developing a rock mass strength criterion, it is necessary to find the constants of appropriate intact rock strength criteria and to establish a correlation to scale down these constants as a function of the RMR. For four intact rock strength criteria, the constants for coal were found using the Nelder-Mead method. To correlate the constants of the strength criteria with the coal seam quality values (RMR), a procedure was developed based on finite element modeling of in situ large scale tests for which the RMR was known. A new coal strata strength criterion is proposed, in a principal stress formulation, for modeling coal pillar behavior when the stress field in a pillar is known. A linear relationship is also given, to be used when empirical pillar strength formulas are used to design pillars. The proposed criteria have been evaluated in a case study.

Jan 1, 1993

By Yi Luo

Regulating the face advance rate in longwall mining operation can be an effective means to reduce the disturbance potential to surface structures associated with a longwall subsidence process. However, there are two seemingly different views about the relation between the face advance rate and the disturbance potential associated with dynamic subsidence process. The US mining industry prefers a faster but a constant face advance rate while the German counter- part is forced to select a slower rate due to its mining conditions, especially while undermining sensitive objects. In order to gain a better understanding about these two different approaches, the experiences in longwall mining subsidence in both Germany and US are presented in this paper with the fundamental differences in geological conditions and mining practices.

Jan 1, 2001

During the last decade mechanical rock excavation has become increasingly widespread in the mining industry and, more in general, in excavation engineering. This technology, especially the tools and their operating mode, has developed according to empirical procedures and for this reason their validity should be ascertained by systematically re-examining the rock breakage processes. This topic has been approached in the framework of a joint research project involving the Universities of Cagliari (Italy) and Wollongong (Australia). The investigation has been carried out experimentally as well as with the methods of numerical modelling which is based on fracture mechanics principles. The first results of this integrated research led to the proposal of an interpretation of rock breakage by means of drag tools and to the identification of a basic correlation between the rake angle of the tool and the grain size of the rock fragments produced and, therefore, the energy efficiency of the operation.

Jan 1, 1990

By Peter Cain

Twenty years of research into the design of permanent gateroad support (packs) in coal mines have resulted in two methods of pack design based on engineering principles. The first, the detached block concept, is based on static loading of the support system by an hypothetical detached block. The second, the roof beam tilt concept, is based on the dynamic loading of the support system as the roof beam tilts over the roadway about a pivot point located in the rib-side. The roof beam tilt concept has been used on a number of occasions to design packs in a variety of conditions. However, recent work in the Sydney Coalfield of Cape Breton Island, Nova Scotia, has shown that design criteria based on the roof beam tilt concept in its present state of development are far from universal in application. After a review of published pack performance data, including detailed studies conducted in the UK, France and Canada, it was found that consideration of the mechanical properties of the roof beam produced a design criterion that fitted the available data. Modifications to the design process using the roof beam tilt concept are suggested for use in pack design. The work also revealed that current research in other aspects of coal mine ground control, particularly the areas of powered support design and subsidence prediction, may provide valuable information leading to major advances in this field. Such developments could also extend the application of the roof beam tilt concept to the design of pillar systems.

Jan 1, 1993

By John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U.S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of a recorded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with hump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip. etc.) of the failure of the strata surrounding the active and multi¬panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

Jan 1, 2000

By Thomas Barczak

Hydraulic cylinders are used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support system operate at pressures as high as 7,000 psi to provide the necessary support capacities Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performmce characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control This paper examines the basic operating principles of state-of-the- art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (5) hydraulic failure mechanisms and how to detect them

Jan 1, 1998

By Alan D. Smith

[A standardized checklist in a questionnaire format, was established to investigate selected factors associated with coal nips roof falls, as derived from an intensive review of the literature. A plot study was undertaken to aspect and explore possible statistical relationships that may exist with these parameters. the Purposes of toe study were to: 1. Study in a systematic and empirical fashion selected parameters that may be capable of differentiating characteristics of roof falls; 2. Obtain some predictive indices cased on selected physical and management related variables so that predictions of future problems associated with mine roof falls can be completed, prior to its actual occurrence. Accomplishment of these goals should result in valuable guides to the mining engineer in scheduling exploration work and 4 determining economic feasibility of certain ground control and .lining pro and practices. The parameters associated with mine roof failure that where included in the questionnaire are: working section, county, spar., orientation degrees), pillar dimensions width, length), seam thickness, roof fall dimensions (length, width, surface area, volume), shape of fall (arch, dome, laminar), thickness of thinnest immediate layer, lithology of the first four i.e.-diate roof layers, thickness of h e first four immediate roof layers, type of initial support systems before failure, type of resupport system after failure, length and spacing of bolts in use before failure, length and spacing of bolts planned after allure, presence of .cater, time failure after It coal excavation, distance t3rest ace, physical operation during, time of coo failure, location of the roof fall entry failure occurred ence of sloughing of ribs before failure, and presence of floor heave condition before failure. The typical roof fall had an average roof spar of 20.3 feet, -06 feet depth o coal seam, occurred 136 feet from nearest face, coal seam thickness of inches, p--ar :width off 45 feet surface area D' roof fall 1151 ft2, mainly lamin- shaped, previously rat fore fall between good to very good, little floor heave presence, usually cracks before the fall about 40 percent of reported cases, shales in most of the immediate layers, and usually located in an entry or intersection. in addition, multiple linear regression techniques were employed in the testing process of 18 major research hypotheses in a search for relationships among the various parameters studied of which were found to be significant, once corrected for multiple comparisons.]

Jan 1, 1984

By Craig Collins

The objective was to develop a Real Time Drilling Display System for Rotary Roof Bolting using Analyzing Software to display mapped holes as they are being drilled in real time. The Analyzing Software was developed to analyze and interpret drill sensor data produced during a rotary drilled roof bolt hole by using algorithms and drill sensor data trends to find and locate roof separations or voids. After this software was validated through lab and field testing, its application needed to be tested in a production environment. However, the current method used to record the drill sensor data proved to be cumbersome for the mine to use on a continuous production basis. With different more practical mediums being explored and considered, a Drilling Display System was developed that will both map holes in real time and record the data for later review. With the Analyzing Software's current level of accuracy and with the convenience offered by the real time Drilling Display, the Drill Display System was implemented along with a test mine's current roof control plan and tested as a roof separation "Early Warning System". After installing the Drilling Display System onto a machine, input and suggestions from the mine environment were considered and design changes were made. The real world application provided a design direction that made the information produced by the Analyzing Software both convenient and significant for the test mine. Also, using the Drilling Display System increased the number of drilled holes that were both mapped and recorded. The results from studying these recorded data files lead to refinements in the current algorithms used by the Analyzing Software which increased the overall accuracy and capability of the system A fairly accurate representation of void or separation locations in the mine roof can be determined fromsensor data recorded during production bolting cycle. The immediate feedback on the local roof condition that the Drilling Display System provides, amounts to a quicker and safer alternative to the scratch hole and the video bore-scope examinations that arc performed after the bolting is completed. This project has shown that making the alternative method of examining the roof condition practical for the mine to use is just as important as the accuracy of its results. Based on the results of this field test, this or other methods of reviewing the analyzed drill hole data will be explored.

Jan 1, 2004

By Yi Luo

The responses of a section of railroad to ground subsidence process was monitored as it was undermined by a longwall panel. The subsidence data collected and the observations made through this monitoring program could help us understand betteer the ground subsidence process and its impact on linear structures such as railroads. The data analysis techniques used and the assessment methods presented could be useful to researchers practitioners in the field of mining subsidence.

Jan 1, 1994

By D. W. H. Su

This paper describes geomechanical criteria employed by Consol Energy for selecting mine-specific longwall face supports in the past decade. The criteria include immediate and main roof rock characteristics, floor rock characteristics, critical tip-to-face distance and shield operating range. Detailed roof rock properties from high-density core holes as well as in-mine scope holes are used to evaluate the set load density and shield stiffness required to control the immediate roof and the yield load density required to absorb the load density developed from main roof weighting. Detailed floor rock properties from core holes and in-mine floor bearing capacity tests are used to specify the maximum peak toe pressure as calculated by the Jackson method. The critical tip-to-face distance is evaluated based on the immediate roof rock strength, layering and thickness. The shield operating range is evaluated based on main bench thickness, the presence of thick draw slate, the potential of minor roof falls at the face and transportation restriction. Three case examples representing three different geologic conditions are presented to illustrate the successful application of these geomechanical criteria for selecting longwall face supports within Consol Energy in the past decade.

Jan 1, 2004

By P. Tsang

In order to deal with ground control problems such as roof falls, floor heaves and pillar failures in underground coal mines, a new pillar design method based on the "yield pillar" concept is proposed. Using the finite element model simulation, the functions and mechanisms of the "yield pillar" are studied. The important variables that affect the stability of longwall entry-pillar system are identified. To simplify the geological and mining conditions, a new pillar design method classifies the in-situ roof and floor conditions into four categories: 1) strong roof and strong floor, 2) strong roof and weak floor, 3) weak roof and strong floor, and 4) weak roof and weak floor conditions. The design formulae are derived based on the finite element model simulation, stability study and nonlinear regression analysis. The finite element models used consider the plastic failure properties and time-dependent behaviors of rock. To better organize the finite element model simulation, the orthogonal experiment design is used to arrange the finite element models and proved to be very effective. An application example is used to illustrate the basic design procedures involved in the new pillar design method.

Jan 1, 1993

By K. Y. Haramy

Strong roof helps minimize roof fall problems in coal mine entries. However, the Inability of strong roof to cave readily may contribute to major ground control problems In Iongwall and retreat mining operations. The concern expressed by mine operators prompted this Bureau of Mines study to analyze the effects of strong roof members on ground stability around Iongwall openings. The problem was approached from three directions: development of a theory to analyze the strain energy conditions In the coal and surrounding strata, modeling the effects of different thicknesses and strengths of Coal and roof strata, and field Instrumentation of powered supports In two Iongwall mines. Results from the theoretical and modeling analysis confirm the accepted belief that a strong roof does, In fact, play a major role in high stress concentration problems In and around the Iongwall panel. Analysis of the effect of different roof overhang dimensions and properties on relative strain energy buildup In the coal and roof Is presented. Shield pressure data Indicate possible methods for detecting noncaving roof behind the shields. Strategies to monitor roof overhang and control dangerous conditions caused by the noncaving roof are also presented.

Jan 1, 1988

By Gift Makusha

Pre-feasibility work at Goedehoop Colliery indicated that stooping of the undersized pillars could be undertaken safely and economically. In light of the findings a decision was taken in may 2003 to undertake the project in the 600 area where three panels (628, 630 and 632) were identified for pilot test sites. The findings of the pre-feasibility studies were presented in a paper to the 22nd International Conference on Ground Control in Mining held at Morgantown in 2003 (1). This paper is a progress report for the project 12 months down the line. Work commenced to prepare the sites for mining including, acquisition of equipment, equipping the panels, selecting and training people to undertake the project. Three monitoring sites were set up distributed evenly along panel 628. Each site comprised of a surface extensometer station in the overburden strata adjacent to a pillar underground containing hard inclusion vibrating wire extensometer cells. This combination would be used to record pillar loading ahead of stooping as well as the depth of caving and strata deformation in the goal zone behind the stooping face. In July 2003, support work began to secure the roof and rib sides. The support was required to be at least three-pillar center distances ahead of the mining front to ensure that the effective stooping zone is secured at all times. The NEVID method of pillar extraction developed at Sasol and described in detail by Ismet and Moolman (2) in a Coaltech 20-20 report was adopted for the pilot project. As part of training the selected stooping team was send for a week to Sasol's Bosmanskrans Colliery to familiarize with the NEVID method of stooping. Further training sessions were carried out on site especially on the use of Mobile Roof supports. The first cut was taken on 20 August 2003 by implementing a form of chequerbord mining taking every second row of pillars. Three rows were mined this way which period was considered training to get workers familiar with the new equipment and mining method. On the fourth row the full design span equivalent to mining 4 pillars in a row was implemented taking out all the pillars in successive rows. Production figures gradually increased from 300 to more than 1,000 tons run of mine coal per shift. Panel 628 was mined out at the end of December 2003 and the second of three panels (630) is being mined. Substantial data from the monitoring set up has been recorded since the start of the project. Monitoring will continue to the end of the pilot project and the data will be analysed and fed back into the design tools to improve the design in future undertakings. The pilot project has been a success so far and other old workings are being evaluated for stooping.

Jan 1, 2004

By Thomas Barczak

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water¬to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water¬solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

Jan 1, 2003

By Kudret Tutuk, Serkan Saydam, Sungsoon Mo

"This paper presents an overview of the floor heave management at the Glencore Bulga Underground Operations and investigates the contributing factors to the behaviour of the floor. The mine experienced a number of major floor heave events in gateroads on development. As the longwall face approached the roadways, the magnitude of floor heave frequently increased, while new floor heave also developed. Furthermore, severe floor heave events took place along the longwall face. The most observed failure mode was buckling. While regular floor measurements were conducted to better understand the nature of the phenomenon, and various measures were considered to control the deformation of floor, the mining height was increased for the predicted floor heave domains, which facilitated effective management of the floor issues. The experience in the mine indicates that mainly high horizontal stresses with greater depths of cover and certain types of floor lithology configuration are likely to contribute to the failures of floor strata.INTRODUCTIONThe Glencore Bulga Underground is located in the Southwest of Singleton in the Hunter Valley of New South Wales, Australia. Blakefield South, part of Bulga Underground, commenced longwall mining in 2010, extracting coal from the Blakefield seam, while the overlying longwall panels were previously mined from the Whybrow seam. The coal seam ranges from 4.5 m to 8.0 m thick with the mining heights varying from 2.9 m to 3.5 m. The longwall panels are 320 m and 400 m wide and up to 3.5 km long.The mine experienced a wide range of floor issues around longwall panels LW7 and LW8, both 400 m wide. For instance, the concrete floor in the travel road failed and lifted as the longwall retreated in close proximity as can be seen in Figure 1. Figure 2 shows the beam stage loader (BSL) buried into the lifted floor, and Figure 3 shows a timber prop distorted due to the movement of the floor. In addition, severe deformation of the floor along the longwall face impeded the longwall operation, as shown in Figure 4."

Jan 1, 2018

By Houquan Zhang, Yu Wu, Yanlong Chen, Zhenfu Luo, Aihong Lu

"A non-destructive detection scheme for bolt installation quality was designed by adopting the method of non-destructive detection on bolt installation quality. Based on the field measurements, a random non-destructive detection method for determining the characteristic length including anchoring length, free segment length and initial axial load of bolt was discussed, and the characteristics of increasing bolt axial load in the initial stable stage was obtained. The results show that the bolt axial load and deformation of surrounding rocks correlate each other. Compared with the traditional detection technique for bolt installation quality, the non-destructive detection method has obvious advantages such as random, accuracy, and economic. The method provides a reliable basis for bolt support optimization and stability control of surrounding rocks.INTRODUCTIONBolt support in roadway can make the surrounding rocks and bolt form a structure in the early stage of roadway development through the bolt pre-tension, which can maximize the self-bearing capacity of surrounding rocks. Thus it is a form of active support (Kang, 2007). In order to make the bolt play an active supporting role, it needs to ensure the installation quality of bolting. Thus the bolts can supply a high initial anchoring force and control the deformation of surrounding rocks (Shan, 2009; Wei, 2012). Moreover, bolt supporting is a concealed work. Once installation quality problems appear; it will be difficult for effective detection and screening (Xie, 2008).THE PROBLEMS OF BOLT INSTALLATION QUALITY IN COAL MINE AND ITS DETECTIONThe Problems of the In Situ Bolt InstallationDue to the problems in installation environment, machine, and technique, and workers proficiency (Li, 2003), there are many problems exist in bolt installation. If the borehole depth is too long, the anchoring agent will accumulate at the bottom of the bore, which reduces the anchoring length. Furthermore, if the borehole depth is short due to the poor geological condition, the exposed part of the bolt will be too Jong and the pallet cannot cling to the rock face, which prevent the pre-tension from being applied. The pre-tension is very important for bolt installation. If pre-tension is insufficient the rock bolt cannot control the deformation of surrounding rock efficiently and the bolt anchoring force will decrease considerably. The bolt length is another important parameter for anchoring quality, which will affect the control area of bolt supporting. In addition, the cleanness of drill hole has a great influence on the effective anchorage length of bolt. If the drill hole cleaning is not enough, it will directly affect the anchoring agent and the contact area of surrounding rocks, which will decrease the effective anchorage length and initial anchor-force."

Jan 1, 2016

By Abdolreza (Reza) Osouli

Determining the roof stability condition of underground coal mines in the Illinois Basin is sometimes very challenging. The roof stability of Illinois mines are mostly affected by two types of shales: Anna Shale and Energy Shale. These layers are sometimes weak in parallel bedding when subjected to horizontal stresses. The roof rocks in the Illinois Basin are are typically more moisture sensitive than the other coal fields. In this study the geotechnical properties of some of the shale units as well as limestone layers will be presented. The geotechnical properties of roof rocks consist of moisture content, unconfined compressive strength, slake durability, indirect tensile strength, and point load tests (Axial and Diametral). The correlation of indirect tensile strength versus diametral point load strength as well as unconfined compressive strength versus axial point load test are explored and discussed. These correlations will help in identifying the roof mass index and planning appropriate roof control measures. This study also evaluates the application of CMRR rock mass index for an Illinois coal mine.

Jan 1, 2014

By Kevin J. Ma, John Stankus, Dakota Faulkner

"Expandable rock bolts are widely used in hard rock mines as an efficient ground control product. However, capacity and service life can be significantly reduced if the metallic body is subjected to corrosion. In some hard rock mines in the U.S., highly corrosive ground conditions exist, and it has been reported that inflatable rock bolts have corroded within a few months after installation. To provide mining industry a cost-effective inflatable bolt and combat the corrosion issues, Jennmar Corporation, Inc., and its subsidiary Keystone Mining Services, LLC (KMS), analyzed corroded bolt samples, identified root causes, evaluated properties of various coating materials, and developed a new inflatable rock bolt, Python M3TM, that is protected with an innovative PyFlexU2TM coating. The new generation Python M3 features improved steel chemistry for reliable performance, modified profile for better inflation, and surface preparation and coating application. The PyFlexU2 is impervious to liquid and air, durable, and UV resistant. With a flexible adhesive, and highly corrosion-resistant undercoating, and a very hard sacrificial surface coating, the PyFlexU2 coating system provides the Python M3 superior protection against chemical corrosion and physical scratch damage. The under-coating has exceptional flexibility and adhesion to prevent coating micro-cracks or fractures after bolt inflation and possesses excellent corrosion resistance to acids (pH <3), alkalis (pH >11), fuels, and salt solvents. The corrosion and scratch resistant PyFlexU2 coating offers very effective bolt protection for extra longevity in highly corrosive environments. The Python M3 coated with PyFlexU2 has been tested in the most challenging conditions, including laboratory corrosion tests in extreme acidic and basic solvents, rock slurry, and borehole scratch insertion tests. With demonstrated corrosion and scratch resistance, the product has been greatly welcomed by hard rock mines in the West and is currently installed in large scale. This paper identifies the root causes of the bolt corrosion, discusses the analysis process, and details laboratory and underground tests carried out on the Python M3 coated with PyFlexU2. The Python M3TM and PyFlexU2TM are subjects covered by pending U.S. Patent Applications assigned to FCI Holdings Delaware, LLC."

Jan 1, 2017