Search Documents

By Daniel W. H. Su

This paper presents the results of an extensive geomechanical testing and monitoring program conducted at a longwall panel. The field program included the monitoring of roof caving sequence and mechanism, surface subsidence, change of pillar stress, roof displacement and entry convergence, and strength characterization of the overburden rocks. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed the instrumented locations. Overburden response to longwall mining was monitored using time domain reflectometry (TDR) technology; and, the height of the highly fractured zone above the gob was determined by postmining drilling. Good correlation was found between the height of the highly-fractured zone and the TDR, subsidence, and pillar stress data. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining. A preliminary model representing the overburden strata behavior at the test site in response to the longwall mining is proposed.

Jan 1, 1987

By Hanjie Chen

A mine panel collapse may occur when pillar sizes are too small or the surrounding rock strata (roof or floor) yields. After a small pillar fails, its loading is rapidly transferred to adjacent pillars that in turn fail. If the surrounding rock strata yield, the loading on pillars will redistribute. which may result in some pillars under high stress. This paper analyzes the causes of two cases of mine panels failures in two room and pillar mines. One case of massive pillar failure occurred in a phosphate mine and the other, mine panels failure, is in a coal mine. In the phosphate mine, both the roof and floor strata were a thick competent shale stratum. The finite element analysis shows that the major reason for the massive pillar failure is that the pillar sizes were too small in a panel. In addition, the high cliff topography has some influence on the failure. In the coal mine, the failed area was about 1,000 ft long by 760 ft wide (covering more than 3 panels) involving 390 pillars. The harrier pillars between the panels were punched on retreat into small chain pillars and the extraction ratio in this failed area was more than 80%. The roof remained intact, and pillars were crushed and punched into the floor. Based on the stress analysis, it is found that multiple panel collapse occurred because the barrier pillars were punched into small pillars and the loading on panel edges increased due to floor failure.

Jan 1, 1999

By Christopher Mark

After the United States and Australia, South Africa has the largest. modern underground coal mining industry in the world. Historically, South Africa has been the cradle of many innovations in ground control, particularly in the area of pillar design. Today, South African mines are grappling with many of the same issues faced by their U.S. counterparts, including safety during pillar retreat operations, selecting the proper roof support, and maintaining long-term pillar stability. The author recently visited seven underground mines in the Mpumalanga, Free State, and KwaZulu-Natal provinces. Mining methods included longwall, room-and-pillar with continuous miners, and drill-and-blast. The mines represented a cross-section of geology and ground support practices. At each mine evaluations were made of the Coal Mine Roof Rating (CMRR), roof support practices, pillar design methods, and general ground control experience. The coal seams observed were generally thick (2-5 m), the depths of cover moderate (less than 200 m), and the roof rocks relatively strong (CMRR greater than 45). Unfortunately, the South African roof fall fatality rate is approximately three times greater than in U.S., perhaps in part because roof bolts seem to be more widely spaced in most South African mines. Roof bolting equipment was generally outdated, and the quality of bolt installation was a major concern. Pillar design, on the other hand, is quite advanced, and pillar failures are rare. Several novel partial pillaring techniques are employed, including "checkerboard" mining in which every other pillar is removed, 3-cut systems, and high-extraction mining where engineered final stumps are left by design. The paper also offers observations on ground control management techniques (including recently introduced Codes of Practice), the role of the mine inspectorate, and the status of the research community.

Jan 1, 1999

By Thomas M. Baraak

This paper evaluates factors which influence longwall support and strata interaction. The longwall system is composed of an immediate and main roof structure and three supporting foundations: 1) longwall panel, 2) powered roof supports, and 3) gob waste. The main roof forms a structure that is generally supported by all three foundations, while the immediate roof acts as a beam that cantilevers from the coal face to the powered support. In most cases, shield loading involves a complex interaction of both main roof and immediate roof behavior and is a combination of loads produced from subsidence of the main roof and displacements of the immediate roof caused by deformations of the cantilevered roof beam. Since the shield stiffness remains constant for all leg pressures and main roof convergence is irresistible in terms of shield capacity, the shield must be able to control the behavior of the immediate roof or floor structure for shield loading to be sensitive to setting pressures. If the goal is to minimize total shield loading, any active setting force must be offset by reduced passive shield loading to justify the active setting loads. Field data suggest that the typical reductions in passive loading do not justify the required increases in setting pressure in some applications.

Jan 1, 1990

By S. M. Hsiung

A model (support selection model) for the selection of suitable types of powered supports under various geological conditions is proposed. This model is developed by evaluating the support, performance under different roof conditions at longwall faces in terms of five controlling parameters: (1) roof Falls, (2) front abutment pressure, (3) Face convergences, (4) gob materials entering into working area, and (5) roof caving line. This model suggests that more than one type of powered support. may be used under the same roof condition and the best selection should he based on the magnitude of suitability index of each support- type. The development and application of suitability index arcs discussed. Fourteen panels in seven coal seams are discussed in the paper to illustrate the applicability and effectiveness of this model. A roof classification system at longwall faces developed specifically for the construction of the selection model is also discussed. A simple example fur determining roof classification index is given.

Jan 1, 1988

By Eric G. Zahl

Researchers at the Spokane Research Laboratory of the National institute for Occupational Safety and health are evaluating stress and displacement measurements in a longwall coal mine. The objective is to determine the best indicators of coal bump hazards during operations so that mine foremen and technical stall can make more informed intervention decisions to protect miners from coal bumps. Instruments were clustered in two panels, a yield pillar, and the immediate roof and floor of a two-entry longwall coal mine. Data were gathered continuously from a variety of instruments as mining proceeded toward and past the instrument cluster. Researchers and the mine's technical staff evaluated these data with respect to coal bumps and bump mechanisms. Selected graphs were then presented to mine foremen on a periodic basis to test their usefulness in identifying hazards. Of particular interest was the use of horizontal stress data from the immediate roof. To measure changes in horizontal stress, a new technique was devel¬oped for installing a grouted biaxial stressmeter in the roof. An evaluation of the development of this stress monitoring system in producing data beneficial to mine foremen is presented.

Jan 1, 2000

By Z. T. Bieniawski

A major study was performed on determination of long term strength of coal strata directed to the design of coal pillars to ensure their stability beyond the life-time of a mine. Based on field investigations, numerical modeling and reliable data from 12 case histories, three aspects of time effect in the strength of coal strata were studied; (1) strength reduction based on the concept of volumetric strain estimate from in-situ tests, (2) strength reduction in terms of three failure criteria applicable to coal strata: original Hoek-Brown criterion, modified Hoek-Brown criterion, and Generalized criterion, and (3) long-term strength estimation as a function of coal strata quality RMR based on case studies. From these investigations, an integrated approach to long-term pillar stability is proposed, based on numerical modeling and empirical pillar strength formulation. The values of factors of safety for coal pillars are analyzed in terms of probability of failure and practical meaning for mine design purposes.

Jan 1, 1994

By David J. Reddish

Longwall systems are inflexible in layout, intolerant of disruption and represent a substantial investment. It is therefore essential drat all understanding of the likely strata behaviour and support requirements is obtained prior to panel development. For many tears rock mechanics engineers have applied numerical modelling based kill finite element techniques to the design of the support and layout of underground excavations. Whilst such design methodology has worked well in civil engineering and hard rock situations, it has been less reliable when applied to excavation design in the soft rocks of the coal measures. This lack of reliability has been identified largely as being the result of the utilisation of unsatisfactory input data, This paper describes the results of an ongoing research programme at the University of Nottingham in which a novel rock mass rating system known as the UK Coal Mine Classification system was developed to enable the prediction of the strata properties that are required as input parameters for use in numerical modelling of the deformation of soft rocks around excavations such as roadways and longwall faces in coal mines. The paper describes the development of the system. the way in which classifications are applied to derive input data for numerical models and gives two case studies ill which deformations and stress re-distributions around coal mine excavations have been simulated by numerical modelling using the FLAC finite difference code.

Jan 1, 2000

By Leslie Carver

The effects of longwall mine subsidence on water resources were studied at a West Virginia coal mine (mine Z) by Carver (1994). Data were obtained for 137 domestic supply wells and springs and 12 baseflow streams. Subsidence caused short-term dewatering (of a few days to weeks) of wells located on lower hillslopes and valleys, and long-term dewatering of hillslope and hilltop springs (with no recovery yet). New or increased spring discharge was observed at lower elevations. Unsubsided water supplies experienced no dewatering beyond a nearby panel's 27°-38° angle of dewatering influence zone. Subsidence from longwall mining beneath streams commonly reduced discharge when panel ages were less than two to three years. However, "normal" discharge was typically observed over panels greater than three years in age; such streams exhibited lower baseflow recession constants, moderated winter baseflow, and increased summer baseflow compared to unsubsided streams.

Jan 1, 1994

By Thomas L. Vandergrift

With the inevitable expansion of homes, businesses, and infrastructure in coal mining regions, the potential for future subsidence above abandoned mines is of increasing concern. Of particular concern are areas underlain by room-and-pillar coal mines. Unlike areas above longwall mines, where total extraction causes subsidence in a predictable and timely manner, subsidence above room-and-pillar mines is difficult to predict and may be active for many decades. As part of a geotechnical assessment of a water pipeline replacement project, NSA Engineering recently performed an evaluation of tong-terns subsidence potential along the proposed alignment due to time¬dependent failure of underlying room-and-pillar workings. The alignment of the replacement pipeline closely follows an existing concrete pipeline, which lies 150 11 to 300 fl above workings that both pre- and post-date the pipeline. Annual surveys along the existing alignment indicate that some subsidence has occurred, primarily from partial pillaring performed in the early 1980's, but that this subsidence is not active. Using the boundary-clement code LAMODEL as the primary analysis tool, NSA followed a three-step approach to estimate future subsidence impacts on the replacement pipeline. First, historical information for the mine was compiled, allowing for calibration of models to actual field conditions. Then, numerical models of workings directly under and adjacent to the proposed alignment were nun, with model input parameters varied until resulting loading patterns matched historical data, and subsidence in the model approximated that measured along survey lines. Finally, time-dependent deterioration of coal pillars was simulated by decreasing the coal strength in the calibrated model until a realistic "worst-case" condition (stability of barriers, but Yielding of production pillars and pillar remnants) was attained. Subsidence from the previous calibrated model was then subtracted from that of the worst case model to estimate future subsidence and related ground movement parameters that slay occur along the proposed alignment. The replacement pipeline design, incorporating couplings capable of withstanding the ground movements predicted, is now being finalized.

Jan 1, 2000

By N. P. Kripakov

The U.S. Bureau of Mines (USBM) is conducting research to develop a practical computer-based tool that will allow coal mine planners to anticipate rock mass behavior surrounding mine entries prior to actual mining. More specifically, this tool estimates to what degree and extent the immediate roof and floor strata and the coal pillar ribs surrounding an opening will weaken or fail for a given set of mining parameters. The technical approach couples together two numerical techniques: the boundary-element method and the finite-element method to allow for an approximate three-dimensional simulation of actual mining situations. Outputs from plan-view, linear-elastic, boundary-element models executed at different mining stages are used as input to a detailed, section-view, finite-element model to estimate the degree and extent of failure expected to occur around the periphery of an entry system. Using a pseudo-elastic approach. elastic rock mass properties are continually updated as different zones are predicted to fail. The procedure is relatively easy to use and is being set up to work interactively with the user who will not be expected to be a computer expert. Inputs include easily understood parameters obtainable from the field and rock mechanics laboratories. Examples of computer-generated output from generic sample models representing typical mining situations are presented and results discussed.

Jan 1, 1994

By Gregory M. Molinda

An investigation was conducted to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure, and suggestions for controlling this problem are presented. Hazardous roof conditions identified in a number of mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52% of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath a number of valleys in the form of bedding-plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomenon, was found at mining depths as great as 300 ft. In situ horizontal stress measurements in a mine beneath a valley and the adjacent hillsides confirmed valley stress re1ief. Underground mapping showed that roof falls in excess of 100 ft in length and up to 25 ft high closely aligned with the valley axis. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress. Thickness of cover, valley shape, and the orientation of the valley relative to the maximum regional horizontal stress all influence the "valley effect" on roof stability.

Jan 1, 1990

By K. Y. Haramy

Deep coal mines with strong roof and floor strata frequently encounter face and rib bursts. The burst problem becomes more severe with increased depth. While the exact causes of bursts are often difficult to determine, localized high stress zones are common to their occurrence. This Bureau of Mines report describes a study at a mine using longwall systems that experienced both face and floor bursts. The study correlates shield loading, entry closure, and forward abutment pressure increases to observed burst occurrences. The results indicate that strong roof strata that overhang behind the longwall supports create additional abutment stress. When caving lags behind the face and the abutment zone does not advance ahead of the face during mining, stresses on the face may increase to a critical level, resulting in a burst. The critical level occurs when the stress in the abutment zone exceeds the ability of the coal and/or adjacent strata to store strain energy. Caving characteristics may be improved by inducing fractures in the roof or by providing sufficient support resistance to shear the roof. Data analysis of a major burst indicated a dramatic increase in floor heave, with a maximum occurring 80 to 100 ft inby the face, and a lag in the cave line behind the face supports. Analysis of the effects of caving characteristics and floor heave on burst occurrences is presented.

Jan 1, 1987

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By Andrew Hyett

Over the last 30 years, a transition away from end-anchored bolts to fully grouted rock bolt systems has occurred in many underground mines. It seems geomechanically intuitive that the success of such bolts, which interfere with rock movements around underground excavations through a variety of complex interactions, is precisely why they remain challenging to instrument and monitor. Whereas measuring the load profile for an end-anchored mechanical bolt is trivial, for a fully grouted system, the load may vary dramatically due to discrete rock movement at cracks and joints. Despite the challenges, measuring the strain (i.e., load) along fully grouted rock bolts remains very appealing, and a lot of valuable research has been conducted using foil resistance strain gauges, particularly in US coal mines (Signer and Jones, 1990). Despite good intentions, more widespread adoption of this instrumentation remains unlikely for the following reasons: (i) The technology is expensive, partly because Intrinsically Safe (IS) requirements limit the number of suppliers and solutions. (ii) The technology is perceived as challenging to successfully implement except by those who are skilled in the art. (iii) The reliability of the technology is questionable in harsh environments. (iv) The technology relies on discrete pairs of strain gauges that may not capture the complete strain distribution along the bolt. No existing alternative technology can offer a solution to all of these limitations. However, in this paper, we introduce results from a new Distributed Optical Sensing technology that promises significant potential. Since the technology is capable of distributed sensing, our results suggest that this new technology can, for the first time, reveal the detailed strain profile along fully grouted rock bolts.

Jan 1, 2013

By R. Kaund

"Quantifying the rockburst consequence is of critical importance to reduce the hazards with preventative measures in underground mines and deep tunnels. Contours of energy components within a pillar model are plotted at different rockmass damage stages, and plastic strain work and released energy are proposed as indicators of rockmass damage consequence. One pillar model under different loading stiffness is simulated to assess indicators of pillar burst and the resulting damages. The results show the rockmass damage under soft loading stiffness has larger magnitude of plastic strain work and released energy than that which is under stiff loading stiffness, indicating the rockburst consequence can be quantified with plastic strain work and released energy in numerical models. With the quantified rockburst consequence, preventative measures can be taken to avoid severe hazards to mine safety.INTRODUCTIONWith the increasing demand of mineral resources and depletion of near-surface ores, the depths of underground mines have made the mining activities one of mankind’s most dangerous types of work (Ortlepp, 2005). The Mine Safety and Health Administration (MSHA) defines rockburst as “a sudden and violent failure of overstressed rock resulting in the instantaneous release of large amounts of accumulated energy.”The types of rockburst can be classified into three types: (1) strain burst, (2) pillar burst, and (3) fault slip (Müller, 1991). Strain burst is the most common type of unstable rock failure in underground openings, where the intensity and scale are usually smaller than pillar burst and fault slip (White and Whyatt, 1999; White, Williams and Whyatt, 2002; Ortlepp, 2005). The cause of strain burst can range from shattering of rock under high stress concentration to buckling of discontinuities parallel to underground openings. The occurrence of pillar burst also depends on the stress and discontinuity conditions in the rockmass, but pillar burst usually involves the sudden loss of strength in the core or foundation of a pillar (Whyatt and Blake, 2002; Kias and Ozbay, 2013; Khademian et al., 2016). Fault slip or slip burst can be either slip along pre-existing discontinuities or shear failure in the rockmass, when the shear stress is larger than shear strength in the fault (Rice, 1983; White and Whyatt, 1999; Sainoki and Mitri, 2014). The consequence of fault slip can vary from very small rockmass damage to consequential rockmass damage, but large seismic magnitude does not always result in large rockmass damage (White and Whyatt, 1999; Whyatt and Blake, 2002)."

Jan 1, 2018

By Daniel W. H. Su

Thick, massive sandstone present in close proximity of the mining horizon can create difficult longwall caving issues, which may lead to severe face loading and subsequent face roof control problems. Under deep cover, such delayed caving and overhang not only impose additional loading on the gate road pillar system, but they also increase the potential for large seismic events. Such a combination of thick, massive sandstone geology and deep cover was present over a portion of a southwestern Virginia coal mine, which was confirmed via detailed in-mine roof scoping and mapping. Large seismic events were recorded over a district of 1,000-foot-wide longwall panels. This paper presents the ground control design changes implemented to reduce longwall-induced stresses in the sandstone, to reduce longwall abutment pressures in the gate road pillars, and to reduce the magnitude of mining-induced seismic events. A series of two-dimensional finite element models were constructed and analyzed to evaluate the longwall-induced stresses in the sandstone above the gate road pillars and the abutment pressures within the gate road pillars. Results from the analyses indicated that reducing the panel width from 1,000 to 700 feet reduced the longwall-induced stresses in the sandstone by a factor of 2.0. Specifically the probability of sandstone stability improved from 29% for the 1,000-foot-wide panel district to over 95% for the 700-foot-wide panel districts. Also, the subcritical 700-foot-wide panel, coupled with a change in pillar design, considerably reduced the longwall-induced abutment pressures in the gate road pillars, which significantly increased the gate road pillar stability factor. Surface subsidence measurements conducted over the 1,000-foot-wide panel district and two new 700-foot-wide panel districts were in very good agreement with those predicted by the finite element models. In addition, results from the models indicated that wider panels with a smaller district may produce the same probability of sandstone stability. One four-panel district and one five-panel district with the new ground control design changes have been mined successfully. The panel width was found to be the most influential factor in determining the longwall-induced stresses in the sandstone and in the gate road pillars. The thickness and massive nature of the sandstone, the proximity of the sandstone, and the strength of the sandstone were also found to be important factors. Seismic monitoring over the two mining districts that employed 700-foot-wide panels confirmed the reduction of one order of seismic magnitude when compared with those measured over the 1,000-foot-wide panel district.

Jan 1, 2014

By S. S. Peng

To acquire knowledge on the general trend of primary and supplemental supports used in tailgates of US longwall mines a survey of 76 mines with 86 longwall panels was carried out in the summer of 1993. This paper attempts to provide some insight on most commonly used support types as primary and supplemental supports in tailgates. Analysis of the surveyed data show that fully grouted resin bolts and cribs are the most commonly used primary and supplemental supports in tailgates in longwall mines of USA.

Jan 1, 1994

By Xinchuan Xia

Based on the stepwise strain features and the strength reduction law of the surrounding rock in extremely softrock roadway, this paper proposes a dynamic supporting principle. A new kind of stepwise reinforced technology, which consists of immediate shotcreting, timely bolting and delay grouting, was optimized after thorough analysis and illustrated with a successful engineering example in extremely difficult softrock roadway.

Jan 1, 2000

By G. Bucelluni

An essential element of truss bolt installation requires machines to angle a hole in the top of approximately 39° to 45° from its vertical axis. Parameter which inherently effect the drill position are: height, width of truss, physical size of mast, and whether single or dual mast bolting is utilized. The combination of these facets govern the installation procedures required for the bolting cycle. The following illustration with written explanation will demonstrate this concept. See Figure #1. [ ] This model assumes certain fixed criteria which corresponds to a dual mast drill design and a set 41° drill angle. Using the derived formula, the maximum possible seam height for both masts to touch the bottom can be calculated for any given condition by substituting by the appropriate bolt spread distance. [ ] In a high seam application where the mast touching the bottom was considered a requirement, the proposed model demonstrates the advantage of single mast drilling. See Figure #2. [ ]

Jan 1, 1982