Search Documents

By Richard H. De Voto

The McDonald Gold Project and two satellite gold deposits near Lincoln, Montana, contain at least 9.9 million ounces of gold and 30 million ounces of silver. The McDonald gold deposit alone contains 7.2 million ounces of gold reserves that can be open-pit mined and processed by cyanide heap leaching at a projected cash operating cost of $190 per ounce. The deposit is predominantly oxidized with no chance of acid production, and can be mined, operated, and reclaimed with minimal permanent environmental disturbance other than the creation of an open pit filled with a fresh-water lake which would support trout. The Seven-Up Pete Joint Venture, the owner of the McDonald Gold Project, commenced permitting of an open-pit, heap-leach operation in November 1994. In 1998, Montana citizens passed an anti-cyanide, open-pit mining initiative, 1-137, which banned any new open-pit gold mine which uses cyanide processing, The Venture has conducted extensive studies, including metallurgical testing of the treatability of McDonald ores with alternative lixiviants, and has determined that all other mining and metallurgical treatment systems are vastly uneconomical in the recovery of gold and silver from the McDonald deposit. Therefore, the Venture's proposed open-pit mining and cyanide heap-leach processing is the only technology that can be applied economically to the McDonald deposit. Further, the analyses convincingly demonstrate that the proposed open-pit, cyanide heap leaching technology results in maximum resource conservation of this valuable and unique deposit and poses far less risk to human health and the environment than any of the alternative technologies.

Jan 1, 1998

By Stephen W. Paff

The EPA has estimated that there are over 3,000 sites across the United States contaminated with lead. Techniques to remediate these sites include standard stabilization/disposal technologies, reclamation of lead using secondary lead smelters, soil washing, and biological removal technologies. In this paper, the current technologies used for lead remediation will be reviewed. Factors affecting the use of each technology, such as range of applicable concentrations, soil types, interferences from other contaminants, economics, and current technology status will be assessed. The paper will also focus on the results of a recent study completed by the Center for Hazardous Materials Research (CHMR), in conjunction with a major lead smelter, which demonstrates that secondary lead smelters may be used economically to reclaim lead from a wide range of lead-containing materials frequently found at Superfund sites. Such materials include battery case materials, lead dross, and debris containing between 3 and 70% lead. The results of development work completed by CHMR on the Acid Extraction Treatment System (AETS), which has been demonstrated to extract Lead from soils containing up to 30,000 mg/kg lead, will also be presented. The use of these technologies will be compared with other options for the remediation of sites.

Jan 1, 1994

By M. Waladan

The top submerged lancing Sirosmelt system has been developed through laborator.y scale testwork and pilot plant trials for recovery of zinc from ISF slag. The effects of the process variables of gas injection rate, method of coal feeding, and temperature on zinc fuming rates were studied in the laboratory. It was found that the rate of zinc elimination was dependent on all of these variabl.es. The rate of zinc removal from slag was independent of zinc content of slag down to approximately 1.5% Zn, below which the rate was proportional to zinc content in slag. Pilot plant trials were carried out to evaluate a proposed process and results followed predictions from the laboratory scale tests. A comparison of the proposed process with conventional slag fuming operations is made and it is shown that the process has a number of advantages which have a significant impact on the economics of zinc slag fuming.

Jan 1, 1990

By Batric Pesic

The interactions of mineral-pyrite with T. ferrooxidans were studied by using a cyclic voltametry technique. The interactions with bacteria were carefully examined during the entire growth stage of bacteria (fermentation). Several very important discoveries were made. For example, the pyrite surface invariably drastically changed its properties at the second day of fermentation. Beyond two days of fermentation, the cyclic voltamograms were insensitive to convective diffusion produced by stirring. The SEM study revealed that bacteria populated the pyrite surface at an extremely high density levels. The high density of bacteria, and the solid reaction products formed on the pyrite surface created conditions for pore diffusion which explained why the CVs became insensitive to convective diffusion in solution (stirring).

Jan 1, 1990

By Miroslav Raudensky, Kallol Bera, Jaroslav Horsky, Jee G. Chang, Ampere A. Tseng

"A combined experimental and finite element approach to study the local heat transfer coefficient is presented in this paper. The heat transfer coefficients at different cooling regimes in a roll are quantified by an inverse heat conduction technique; the heat transfer phenomena involved are then discussed. A discussion of the application of the heat transfer information found in the present study for better design of a roll cooling system is also included. Finally, an identification of areas where further work is needed is presented.IntroductionIn metal rolling processes, the roll is used as a tool to deform the workpiece at very high speeds. As shown in Fig. 1, the heat transfer phenomena involved in the process are complicated by the interaction between the roll and the strip, mainly including 1) the heat transferred from the workpiece to rolls in the contact regions, 2) the heat created in the interface due to the deformation of the workpiece and the friction between the workpiece and roll, and 3) the heat removed by watercooling as well as the ambient air. All of these transport phenomena occur at extremely high pressure, high speed, and high heat flux; these make the control of the roll temperatures an extremely challenging problem.In hot rolling, proper cooling of rolls can lead not only to improve the roll shape quality by controlling the thermal crown of the roll, but also to extend the roll life by minimizing the thermally induced stresses [1,2]. Also, knowledge of roll temperatures can contribute to insights about the roll/workpiece interfacellubricant behavior, and lead to the desired surface condition of the workpiece. Therefore, adequate roll cooling or control of roll temperatures is of critical concern to mill designers and process engineers. In order to have proper operation of the process, a good understanding of the influence of cooling practices on the roll is essential [3]."

Jan 1, 1994

By Guoqiang Lv, Xi Yang, Wenhui Ma

Cast multicrystalline silicon ingots are widely used in photovoltaic manufacturing. A key issue to achieve high solar cell efficiencies is to attain an optimized temperature field during directional solidification (DS) process. This paper reports numerical investigation of multicrystalline silicon (mc-Si) ingot production using two major types of DS furnace. Specific examination is made on thermal distribution, interface shape and stress field. Evaluation is performed for the applicability of thermal system design to reduce thermal stress, improve crystal quality and enhance energy efficiency. The effects of procedure parameters and geometric configuration on temperature distribution are discussed as well to provide the viable solutions for systems optimization.

Jan 1, 2015

By Bowen Li, Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"Magnetic iron sulfide ore particles heat rapidly by microwave (MW) irradiation generating plasma during oxidation of surfaces. The high temperatures produced by the exothermic event decompose local portions of samples forming a differentiated flux of partially melted silicate (si-mt) with entrained metal-sulfide (sul-mt) droplets. The si-mt forms crystals of olivine (01) in Ca-rich pyroxene (Cpx) melt that resorbs a portion of iron sulfide (Po). The immiscible sul-mt droplets of (Fe,Ni,Cu)1-xS contain magnetic subsolidus Ni-pyrrhotite (Ni-Po) with Cr-bearing ferrospinel (Mag). Sub-micron sized flecks of Au are found on the surface of a sul-mt droplet with scanning electron microscope (SEM).IntroductionSulfide ore deposits supply the world's mineral resource in the production of non-ferrous metals. Particularly, Cu-Ni deposits are chemically enriched in metals from high sulfur saturation during magmatic formation that creates the proper geochemical environment for metals enrichment [1, 2]. The sulfur and oxygen fugacity control redox conditions of a differentiated silicate/sulfur magmatic melt with the concentration of iron playing a dominate role in the chemical partitioning of metals in sulfide liquid [3, 4]. The initial magnetic crystallization of (Fe,Ni)i-xS monosulfide solution (mss) from metal-sulfide liquid has an exclusive effect on the fractionation of mineral assemblages (zoning) [5].Phase equilibria of sulfide melt (sul-mt) components are related by a miscibility gap with mss forming Ni-rich pyrrhotite (Ni-Po) followed by the crystallization of (Fe,Cu)1-xS intermediate sulfide solution (iss) [6]. Precious metals form stable chacogenides and are retained in solution until the final liquid solidifies. The redistribution of metals now occurs by subsolidus cooling of mss and iss that exsolve low-temperature Fe-Cu-Ni bearing mineral assemblages [7]. The proper interpretation of ore genesis increases processing capabilities by isolating chemically enriched zones during extraction and should be used to aid in sustainable mine site development [8-11]."

Jan 1, 2013

By J. H. Ahn, J. K. Yoon, Jung-Eui Lee

"A concentration change during grade transition operation in steel thin slab casting is predicted with computer simulation, water model and plant trial. Fluid flow and mixing patterns in various tundish levels and flow rates were analyzed through three-dimensional mathematical modeling. Comparing with water model experiments, a simple, efficient and accurate computational model has been suggested to predict the concentration profile at outlet of tundish. Based on the model, mixing in/below the mold was analyzed considering EMBR. The predicted concentration profiles show good agreements with the measured values. It is found that the lower vortices in the mold are suppressed by the electromagnetic field and the plug-like flow region develops which decreases the intermixing of two different grades of steel and shortens the length of transition region.1. IntroductionContinuous casting is the primary mode of production of semifinished steel products as it offers tremendous advantages in terms of energy savings, increased yield and higher productivity over the traditional ingot casting process. Efforts have to be made constantly to improve the quality of the cast product, reduce costs and thus increase the competitiveness of the steel manufacturer. One way of reducing costs is to reduce the amount of intermixed steel during the grade transition operation.Several different procedures exist to handle the casting of dissimilar grades for the conventional slab casting. Each procedure has its own merits and demerits. In order to choose the best method for a particular operation, there are a lot of researches. In the case of present continuous thin slab casting of POSCO mini mill, the only possible method is to change ladle during the grade transition. Due to the high casting speed (3.8m/min-4.4m/min) it is impossible to change the tundish and due to the thin thickness of slab it is also impossible to insert grade separator."

Jan 1, 2000

Al2O3,-WC Composite powder for cutting tools was synthesized by self-propagating high-temperature synthesis using A1 powder as a reducing agent. WC, W2C and Al2O3 were concurrently formed in WO3Al-C system. It was found that the complete reaction was achieved with excessive addition of carbon and appropriate processing parameters such as degree of dilution, particle size of aluminum, compaction pressures of green pellets and carbon source. The final product which was leached by 50% HN03+HF diluted solution was consisted of Al2O3-55wt% WC having 2-3um of mean particle size.

Jan 1, 1999

By William Petruk

The Kidd Creek base metal deposit near Timmins, Ontario contains around 0.15 wt% Sn, mainly as cassiterite. The cassiterite occurs largely as inclusions in sphalerite, with 85% being in grains smaller than 18.5 micrometres in diameter. Concentrates and tails from the company's Cu, Pb and Zn circuits were studied to determine the liberations and recoveries of cassiterite in the products. The ore had been ground to about 65.% minus 44 micranetres in diameter (-325 mesh); 55% of the cassiterite was liberated. About 92% of the liberated cassiterite and 70% of the unliberated cassiterite were in the concentrator tails, and 20% of the unliberated cassiterite in the zinc concentrate. The company had attempted to recover the cassiterite from the concentrator tails by gravitational methods but recoveries were low. The grain size of the cassiterite in the gravity Sn concentrate was similar to the grain size of the liberated cassiterite in the concentrator tails. Research on flotation of the fine grained cassiterite from Kidd Creek ore has been conducted,

Jan 1, 1990

By Baozhong Zhao

Laboratory experiments have been conducted on the removal of As, Sb and Bi from molten copper by SF 6 injection. The results showed that the impurities can be removed by SF6 injection in the? sequence of Sb >As >,Bi and the rate of Bi removal is affected significantly by the concentration levels of As and Sb in the copper melt. Analysis of the experimental data indicates that the impurity removal process is under chemical reaction control rather than by mass transfer of impurity through the molten copper phase. On the basis of experimental results, a kinetic model was developed and the order of chemical reaction and the volumetric chemical reaction rate coefficients of impurity removal were determined.

Jan 1, 1996

By L. Lü, M. O. Lai

"Mechanical alloying is a dry, high energy ball milling process which has been used to synthesize metallic powders in the solid state. The present study use this technique to synthesize Cu-base shape memory alloy powder from commercial Cu70Zn30, Cu86Zn14 and element AI powders. The evolution and formation of shape memory alloy powder were monitored using X-ray diffraction and microscopy. It was observed that shape memory alloy powder started to form after 1.8 ks of mechanical alloying. ? phase was clearly detected after 3.6 ks of mechanical alloying. The intensity of X-ray diffraction of the y phase increased when mechanical alloying duration was prolonged indicating an increase in the amount of y phase. Microstructure observation showed different stages of formation of alloyed powders: welding between powders and formation of layered structure, deformation and fracturing of layered structure, and finally the formation of alloyed powders.IntroductionMechanical alloying (MA) is a process used for producing powders with controlled and extremely fine microstructure. It was original developed in 1966 (1) to produce aNi-based superalloy combining oxide dispersion strengthening with gamma prime precipitation hardening. In recent years this technique has been used in producing a wide range of materials including intermetallic compounds (2, 3), amorphous materials (4-6) and other materials (7-9). In MA, a blend of powders is subjected to highly energetic compressive collision. The powder panicles are welded and fractured during ball milling. Therefore, it is essential that at least one of powders should be ductile to act as combiner. It has however been found that brittle components without soft element can also be mechanically alloyed (10), even ceramic powders (11).The present work aims to study the mechanism of formation of shape memory alloy powder during MA."

Jan 1, 1994

By R. G. Reddy

Viscosities of alkaline metal oxide-silicate melts were estimated using our previously developed mathematical model. The structural based model considers depolymerization effects and related breakdown of the silicate network structure, on the addition of metal oxides to the melt. The developed expression: n =4.9x10 9 NO 0 T ½ exp(E/RT) poise was used to calculate the viscosities of various binary silicate systems such as, CaO-SiO,, MgO-SiO, and MnO-SiO,, as a function of temperature and composition. Excellent agreement was obtained between the calculated and experimentally determined viscosities.

Jan 1, 1991

By Rak-lun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEDs. Efficient blue light-emitting diodes (LEDs) were fabricated using InGaN/GaN triangular MQWs. The LEDs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEDs at 20 mA and 20 °C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LED, but decreased substantially in the rectangular one.

Jan 1, 2003

By Zhitong Sui

Based on several case studies on the precipitating behavior of valuable nonferrous metal compounds (VNMC) in molten slags a green technology for the recovery of VNMC from molten slags was proposed. This technology involves three steps: (I) The selective enrichment of the dispersed VNMC into the designed mineral phase in the molten slag; (2) The selective coarsening of the designed mineral phase to a critical grain size in the molten slag; (3) The selective separation from tailing of the grown mineral phase in the solidified slag by dressing or hydrometallurgy processes. This is a clean and low cost technique and has a great capacity to deal with a large quantity of slags. The utilization of the recovered VNMC such as Titanium, Boron, Vanadium compounds was summarized as examples of application. It was confirmed by experiments that the precipitating behavior of the designed mineral phases like Perovskite(CaTiO3), Suanite(2MgO*B2O3) and Sincosite(CaOoV2O5*P2O5) in molten slags is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the VNMC from molten slags during solidification processes were also investigated.

Jan 1, 2003

By Rak-Jun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEOs. Efficient blue light-emitting diodes (LEOs) were fabricated using InGaN/GaN triangular MQWs. The LEOs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEOs at 20 rnA and 20 "C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LEO, but decreased substantially in the rectangular one.

Jan 1, 2003

By Shengli Wu, Fengjie Zhang, Feng Chang, Hua Lu, Kaiping Du

In order to make a complete understanding of steel plant metallurgical dusts and to realize the goal of zero-waste, a study of their properties was undertaken. For these purposes, samples of two sintering dusts (SD), two blast furnace dusts (BFD), and one electric arc furnace dust (EAFD) taken from the regular production process were subjected to a series of tests. The tests were carried out by using granulometry analysis, chemical analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy via SEM (EDS), and Fourier transform infrared spectroscopy (FTIR). The dominant elements having an advantage of reuse are Fe, K, Cl, Zn, C. The dominant mineralogical phases identified in sintering dust are KCl, Fe2O3, CaCO3, CaMg(CO3)2, NaCl, SiO2. Mineralogical phases exist in blast furnace dust are Fe2O3, Fe3O4, with small amount of KCl and kaolinite coexist. While in electric arc furnace dust, Fe3O4, ZnFe2O4, CaCO3, CaO, Ca(OH)2 are detected.

Jan 1, 2015

By Hojat Naderi

In this research assisted leaching of chalcopyrite using sodium peroxodisulfate was studied. Electrochemical techniques such as Tafel analysis and electrochemical impedance spectroscopy (EIS) were used to investigate the surface reactions of a chalcopyrite electrode in the presence and absence of Na2S2O8. According to the results, addition of sodium peroxodisulfate increases the current exchange of the corrosion process and prevents the formation of a passive layer on the surface of the electrode. EIS tests show the trans-passive dissolution of the passive layer on the chalcopyrite electrode in presence of Na2S2O8. Equivalent electrochemical circuits were modeled for Na2S2O8-free and -containing solutions and the model parameters were compared to determine the effect of S2O8 2− on chalcopyrite dissolution. Copper dissolution from pure chalcopyrite mineral and chalcopyrite concentrate was carried out using 15 g/L sulfuric acid solution with and without Na2S2O8. Simultaneous presence of 10 g/L ferric ion and 40 g/L peroxodisulfate salt results in about 40 and 18% of Cu extraction from chalcopyrite concentrate and pure chalcopyrite mineral, after 96 h, respectively.

By Boxun Lu, Juan Wei, Kun Chen, Wanlin Wang, Lejun Zhou

"Slag system is an indispensable part during the continuous casting process, and playing various important roles like absorbing inclusions, modifying heat transfer rate, preventing oxidation of molten steel, etc. to ensure the smooth process and excellent slab quality. However most slags contains more than 8% fluorides which tend to introduce a series of environmental and health problems. This study involves the research of the removal of fluorine through the chemical composition optimization. Through the studies of CCT, DHTT, XRD and SEM, it has been successfully founded that the crystalline phase of Ca11Si4B2O22 discovered in this study shows very similar crystallization property as Cuspidine (Ca4Si2O7F2), which is the most important crystalline phase in the current fluorine bearing slags. Moreover, the optimized free/low fluorine slag shows the opportunity to replace conventional high-fluorine mold slag for casting medium carbon steels that is regarded as the bottleneck of green slag development for continuous casting.IntroductionMold flux has been widely used in continuous casting to control heat transfer, lubricate the strand, absorb inclusions, provide insulation and prevent oxidation of the molten steel[1-3]. It usually contains fluorides, like CaF2, NaF etc., which are used to control the viscosity and solidification temperature of mold fluxes [4-5]. However, the presence of fluoride leads to corrosion of equipment, serious environmental pollution (toxic volatiles and water pollution), and high processing cost of cooling water[6-7]. Therefore, the study of low or free fluorine mold flux is of interest and attracts worldwide attention.S. Y. Choi et al. [4] used B2O3 as a substitute for cuspidine in steel B2PB2) however, B2O3 content was extremely high (up to 30 w%). Other studies have investigated F-free mold flux by adding or optimizing components as MgO, Li2O, B2O3 et al[8-11]. However, most of these focused on the melting and viscosity issues or for low or ultra-low carbon steels, where crystallization tendency is not significantly strong. Very few studies regarding to the development of low/free Fluorine mold flux for casting medium carbon (MC) steels have been conducted, due to the difficulty of the crystallization and heat transfer control without the formation of cuspidine."

Jan 1, 2014

By Shizhe Liu, Bing Li, Heng Wang, Zuxin Zhao

In this paper, cyclic voltammetry and chronoamperometry have been applied to investigate the effects of Nd2O3 concentration on the anode effects, critical potential for the anode effects and Nd2O3 reduction in LiF-NdF3-Nd2O3 melts at 950℃. The results show that the oxidation peaks in the potential of about 2.7V are attributed to the oxygen ions oxidation and the peak current density increases with Nd2O3 concentration increase from 0 to 0.5wt%. The critical potential caused the anode effects shifts to 0.3V more positive value as Nd2O3 content in the melts decreases from 0.01wt% to 0.5wt%. The cyclic votammograms on W electrodes in the LiF-NdF3-Nd2O3 melts present two pairs of reduction and oxidation peaks, indicating that the reduction of Nd ions in the LiF-NdF3-Nd2O3 melts in two steps rather than one step.

Jan 1, 2014