Search Documents

By P. Peczak

A Monte Carlo simulation technique has been used to study dynamic recrystallization in polycrystals. A continuum microstructure of the polycrystal is modeled employing a discrete lattice. The response of the material to hot deformation is simulated by adding stored energy and recrystallization nuclei continuously with time. The experimentally observed nonuniform character of deformation substructures is modeled by employing a phenomenological expression for inhomogeneous distribution of the stored energy. All simulations were performed on HP-Apollo 9000 Series 700 workstations. A program written in FORTRAN with use of PHIGS graphics library calls was used to interactively monitor the current state of the matrix and all relevant parameters: deformation stress, average grain size and effective nucleation rate. Visual analysis of the simulated microstructure allows a better understanding of the data developed by averaging over a number of very long Monte Carlo runs. Since the essential features of dynamic recrystallization are accurately reproduced by the model, it is used to discuss the role of the controlling mechanisms of the dynamic recrystallization in real polycrystal.

Jan 1, 1993

By V. L. Stolyarova

The high-temperature Knudsen effusion method was used to study partial pressures of vapour species, activities of components and the Gibbs free energies in the DyF3-Dy2O3 system at the temperature (1357±5) K. Partial pressures of vapour species were obtained by the ion current comparison method, with the DyF3 partial vapour pressure over pure DyF3 as a standard. The equilibrium constant of the gaseous reaction DyF3 + DyOF = Dy2OF4 is evaluated. Thermodynamic data obtained are in a agreement with the available phase diagram of the DyF3-Dy2O3 system. Results of the present study illustrate the negative deviations from the ideal behaviour in the system.

Jan 1, 1997

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

By H. Senoh

For the purpose of clarifying the reason caused a drastic decrease of discharge capacity for MmNi3.6Mn0.4Al0.3Co0.7 electrode at relatively low temperatures, various factors influencing the charge-discharge processes were investigated in the temperature range of 25°C to -40°C. The charge efficiency obviously decreased at low temperatures less than 0°C due to a decrease in the rate of the charge-transfer reaction on the electrode surface. Moreover, both the rate of the hydrogen diffusion from the alloy bulk to surface and the rate of the charge-transfer reaction significantly influenced the high-rate dischargeability. The addition of Mo to MmNi3.6Mn0.4Al0.3Co0.7 alloy was found to be effective for improving the electrocatalytic activity, leading to the improvements of the charge efficiency and the high-rate dischargeability at relatively low temperatures.

Jan 1, 2002

By Yuhsuke Mizukami

Crude high Cr containing steel such as tool steel, heat-resistant steel or stainless steel is produced by dissolution of high carbon ferro-chromium into molten crude steel. In the refining process, decarburization is performed at the first stage, and deoxidation is followed in the next stage. Therefore, the equilibrium relation between dissolved Cr and 0 in molten Fe-Cr alloy after decarburization is very important when yield of deoxidizer is considered for the ovemll control and optimization of the process. It is well known that the yield of deoxidizer does strongly depend on the kinds of refractories of furnace in the secondary refining process. In the present work, the equilibrium relation between dissolved Cr and O in molten Fe-Cr alloy has been measured in a Cr2O3, MgO or Al2O3 crucible at steelmaking temperature. O contents at given Fe-Cr components have been lower in order of Cr2O3, Al2O3 and MgO crucible. The present results have been discussed based on the activities of the constituents in pure solid Cr2O3, and FeO-Cr2O3, MgO Cr2O3 and (AI,Cr)2O3 solid solutions.

Jan 1, 2003

By P. T. Velu

Light weight aluminum alloys are the major construction materials for a number of structures in automobile and aerospace industries. Higher cost of production is the key impediment which restricts the usage of these alloys. A new electrochemical process route for the low cost production of aluminum alloys is being investigated, in which alloying elements are obtained from the dissolved compound. In the present investigation, solubility of lithium compound has been determined by measuring the EMF, when it is dissolved in the electrolyte. The solubility of Li2CO3 increased with temperature from 2.95 wt pct at 1063 K to 7.57 wt pct at 1093 K. Activities of the compound in the electrolyte were deduced using Temkin's ideal solution approach.

Jan 1, 1995

By Paykan Safe

This paper reviews various process off-gas cooling options available for sulfide smelting processes. Advantages and disadvantages of each, system are discussed along with the selection criteria for a reliable and cost effective :system. Various systems are presented to demonstrate typical process parameters for smelter off-gas handling systems and to outline operating difficulties associated with each system:

Jan 1, 1998

By C. M. Antony

The galvanizing process involves the use of accessory equipment in a series of aggressive environments including zinc ammonium chloride flux, molten zinc at 45S°C (850°F), and acid for stripping of adherent zinc. An Fe-Ni-Cr-Co alloy has been identified which combines excellent strength and resistance to molten zinc and acid attack making it suitable for accessory equipment. The alloy was field tested by a commercial galvanizer as basket material and was found to provide improved life compared to original low-alloy steel baskets while cross-section thickness was reduced 44%. Additionally, other associated processing cost savings were realized.

Jan 1, 1992

By Jing Zhan, Tian-zu Yang, Wei-feng Li, Li-Hua Jiang, Shi-yan Xu, Jian-yang Huang, Chuan-fu Zhang, Yan-qing Fan

The amount and activity of coal, reduction temperature and other parameters of the process of bottom-blown reduction of liquid high lead slag were investigated in laboratory. Methods to strengthen the bottom-blown reduction process were studied by industrial production. The results were in the follows: the reduction temperature was 1150℃; reduction time was 1.5h; the reductant was anthracite; lead content in slag was controlled to 2%; the rate of coal was 7% and gasification loss of coal in high temperature was severe; liquid lead slag reduction rate was faster with coal; prolonging the reaction size had little effect on reducing lead in slag; the size of the reactor can be further reduced.

Jan 1, 2015

By Ehsan Khajeh

In this study, the permeabilities of Al-15.5wt%Cu and Al-19.5wt%Cu have been determined by solving the full Navier-Stokes equations on 3D geometries of interdendritic channels obtained by X-ray microtomography (XMT). The samples for XMT were sectioned from different positions in directionally solidified cylinders in order to obtain a variety of microstructures for each composition. The flow has been solved using a 2nd-order accurate Finite Volume Method (FVM) approach. The effect of employing uniform or unstructured mesh on the calculated permeability has been studied. The Marching-cube triangulation method was necessary to extract accurate surfaces for unstructured volume meshing. Calculated values of permeability for this range of solid fractions show partial agreement with previous experiments. Observed deviations are attributed to the difficulties of experimental permeability measurements.

Jan 1, 2009

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By Yasuo Kudo, Wu, Hayato Sato, Hiroshi Nakazawa, Shouming

"In order to recover copper from a waste nickel condenser powder, bioleaching experiments were carried out using Thiobacillus ferrooxidans in a shaking flask. The content of nickel and copper in the waste nickel condenser powder in this study were 8.0% and 3.5%. X ray analysis showed the peak of barium titanate. In the preliminary study using metal nickel and copper powders , the dissolutions of nickel and especially copper were accelerated with the addition of ferric iron in the bioleaching of nickel and copper powders while not in the absence of ferric iron. Ferric iron oxidizes both metals, and Thiobacillusferrooxidans oxidizes ferrous iron resulting from the oxidation of metals, whereby the dissolutions of metals proceeds. The dissolution rates of nickel and copper increased with increase in the concentration of ferric iron in the bioleaching of the waste nickel condenser powder.1. IntroductionNickel condensers rejected from manufacturing plants are crushed and landfilled. Waste nickel condensers contain nickel and copper and could be considered as nickel and copper ores. Since the capacity of landfills is diminishing, it is required to recycle metals of waste nickel condensers in order to reduce the amount of wastes landfilled. Conventionally, metals in the waste were recovered by dry metallurgy after the incineration.Nickel has been refined by solvent extraction - electrowinning method (SX-EW method). Recently the amount of copper refined by SX-EW method has increased (Takahashi, et al. 1994). This method is cleaner and consumes less energy than conventional methods. Nickel dissolved well in acid solutions, but copper is not. If copper is leached efficiently from a waste nickel condenser powder, SX-EW method will be applied to recover copper from them"

Jan 1, 2000

By Hui-Gai Li

The fine Ti oxide inclusions precipitated during solidification are favorable for intragranular ferrite nucleation. The oxygen content before solidification affects the composition and size of inclusions. The composition of precipitated inclusions in Mn-Ti alloyed steel was studied by means of thermodynamic calculation and experiment in this paper. The micro-segregation of Mn, Ti and O during solidification was considered in calculation and unidirectional solidification apparatus was employed in experiment to ensure that alloy elements diffused along solidification direction. The results showed that: inclusions are mainly Ti oxide when oxygen content is 10ppm; they are Ti oxide and Mn-Ti oxide when it is 20ppm; Mn-Ti oxide dominates when it is 30ppm. With the increase of oxygen content, the size of inclusions increases. The maximum oxides size is about 3µm from statistical results of experiment.

Jan 1, 2008

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In order to produce good quality ammonium paratungstate, Sn needs be removed efficiently from the tungstate processing solution. The nascent hydrous ferric oxide has excellent adsorption ability and is often used as an adsorbent to remove metal ions from aqueous solution. In this paper, nascent hydrous ferric oxide is used to remove Sn from tungstate solution. Through experimental, the effects of pH value, reagent amount of adsorbent, reaction temperature and reaction time on the Sn removal are investigated. The study shows that 98% of Sn can be removed effectively from sodium tungstate solution and only 2% of W is lost during process under the conditions of pH 9~12, reagent amount of Fe addition 40 times Sn amount, reaction time 30min and room temperature. As the Fe addition reaches 90 times of Sn concentration in the ammonium tungstate solution, 99% of Sn is removed and APT with zero level purity national standard is obtained.

Jan 1, 2014

By Jose M. Gomez-Vega, Osamu Takai, Atsushi Hozumi, Hiroyuki Sugimura

"Ongoing research is reported aimed at improving the properties of mesoporous silica-based coatings on various substrates for optoelectronic or medical applications. Tetraethylorthosilicate (TEOS) was selected as the silica precursor, and amphiphilic triblock copolymers poly( ethylene oxide)- poly(propylene oxide)poly( ethylene oxide) as the surfactant micellar template or structure-directing agents. Cetyltrimethylammonium chloride (CTAC) was also used as a control agent. The effect of the templating agent and type of substrate (glass, Si, and Ti) on the mesoporosity, particularly on the alignment of the mesochannels, has been investigated. Three · different treatments (thermocalcination, photocalcination, and solvent extraction) have been also studied to remove the organic templates.IntroductionThe fabrication of mesoporous silicate-based materials through the utilization of a sol-gel process, where cooperative organization of organic and inorganic species takes place, provides a versatile approach to nanoscaled structures with potential applications in fields such as catalysts, optoelectronics, biomaterials, etc. Compared to conventional low molecular weight surfactants, self assembly of amphiphilic·block copolymers can result in mesostructured materials with larger pore sizes (up to 30 nm).1 Most of the synthetic strategies use silicon alkoxides as the silica precursor, although non-silicate metal alkoxides, e.g; Ti, Zr, Al, and B, have been also used to obtain different mesoporous materials, or even mixed metallic oxide systems. 2 Recently, Yang et al. 3 • 4 were able to synthesii:e a great variety of mesoporous metal oxides ID nonaqueous media using inorganic precursors (metal chlorides) and block copolymers as structure-directing agents."

Jan 1, 2000

By Richard D. Hagni

The mineralogy of dusts from the lead sinter and lead blast furnace at the Doe Run Smelter at Herculaneum, Missouri is being studied by reflected light microscopy and scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS). Oust from the sinter plant consi5ts of abundant slag and galena particles, and lesser amounts of coke, sinter, and chalcopyrite particles. In contrast, dust from the blast furnace consist of abundant coke and sinter particles, and lesser amounts of slag, galena, chalcopyrite, metallic lead and lead-copper particles. The particles in dusts from remote sampling sites !-l mile from the sinter plant and blast furnace are fine-grained and composed principally of calcium-aluminum silicates that are locally derived, but some of the larger particles consist of sinter, slag, galena, and other minerals. Additional dust samples from the plant and remote sites are currently being studied.

Jan 1, 1991

By Jiechao Liu, Lijian Luo, Yubao Ma, Bo Zhang, Yanfeng Yang, Xin Hong, Luming Liu, Jienan Liu

Reduction kinetics of stainless steel slag in iron bath smelting reduction was studied at the temperature of 1500℃ ~ 1650℃. It was concluded that the reduction process consisted of two parts. That is to say smelting reduction was controlled by stainless steel slag melting initially and by interface reaction later. In order to increase smelting reaction rate, the melting point of slag should be decreased at the first stage and adjust the liquidity of slag at later stage. Smelting reaction rate will be accelerated by means of optimize the slag content. The optimal reduction result that all most all of the chromium in slag been recovered was obtained in temperature was 1500℃, basicity of slag was 1.0~1.2, the value of Al2O3+MgO was 25%.

Jan 1, 2015

By Gordon A. Irons

"Powder injection for melt refining is widely practiced in the steel industry, and is gaining acceptance in the non-ferrous industries. In these commercially-important systems, the thermodynamics and kinetics may be very complicated. More than one element may be removed by refining, and often the refining agents are not just one compound. In this paper, the thermodynamic and kinetic aspects of these processes are reviewed. A number of examples are given, such as the desulphurization of iron with a variety of reagent mixtures, and selenium removal from copper with several different reagent combinations.IntroductionI am very pleased and honored to present a paper at this Symposium recognizing the many contributions of Professor Howard Womer. Even at the time I was an undergraduate student, the WORCRA process was part of the curriculum. I remember at the time that I was fascinated by the concept, and due to it and the many other rapid developments in Process Metallurgy, I chose it as my field of study. I think the Symposium is testimony that Professor Womer has touched the lives of many others as well.My original assignment was an overview of the basic aspects of gas and solids injection. However, I reviewed most of this material at the Savard/Lee Symposium [1]. In the present paper, I will present some of the basic issues related to refining with powder injection, using work that we have recently completed in both ferrous and non-ferrous systems."

Jan 1, 1996

By Michel Boisvert

Noranda Metallurgy is presently completing construction of the new Noranda Converter (NCV) at its Home Smelter in Rouyn-Noranda. This capital investment of CDN$56M is the continuation of the Emissions and SO2 Reduction Program that was initiated in the late 1980s with the acid plant for Reactor off-gas treatment. The Patented Noranda Converter was developed and pilot tested at the Home Smelter in the early 1990s. The project will replace the Peirce-Smith Converters and enable sulphur fixation to be 'increased from 70% to over 90% by 2002 with an accompanying reduction of dust emissions to the atmosphere. The construction site is an extension of the present Noranda Reactor area. A number of existing facilities including the acid plant and process air supply were used to minimize the capital cost of the project. This paper provides a brief history of the Noranda converting process, the Home Smelter Emissions and SO2 Reduction Program, ,project implementation and construction, a description of the different facilities, and preparation of human resources for start-up.

Jan 1, 1998

By John A. Mavrogenes

Reflected light microscopy and electron microprobe techniques were used to determine the mineralogy, phase percentages, grain sizes, and textures of Co-Ni-rich mattes. The mattes were produced by submerged bath smelting at the University of Missouri-Rolla Pyrometallurgical Center of a flotation concentrate with 4.S% Co and 5.1% Ni that was prepared at the United States Bureau of Mines Rolla Research Center by flotation up-grading of the cobalt and nickel content of a copper concentrate from the Magmont mine, Viburnum Trend, Southeast Missouri. Nine distinct phases were distinguished in the matte samples, and three of these contain cobalt and nickel. The phases that were free from cobalt and nickel are bornite, chalcocite, pyrrhotite, magnetite, metallic copper, and galena. Submerged bath smelting serves to segregate the cobalt and nickel into phases that can subsequently be recovered by flotation. These phases are: shandite (Ni3PbZSZ)' cobaltpentlandite ((Co,Ni,Fe)9SS)' and Co-bearing Fe-rich sphalerite ((Zn,Fe,Co)S). Most of the cobalt occurs in cobaltpentlandite, but some is present in sphalerite. High total air conditions during smelting favor the development and segregation of cobalt into cobaltpentlandite. Nickel occurs in cobaltpentlandite and shandite. Shandite contains lead, a deleterious constituent in the smelting of cobalt and nickel.

Jan 1, 1989