Search Documents

By Edward Peters

Scandium (Sc) has unique properties and is one of the more valuable elements in the periodic table. Scandium can be used in solid oxide fuel cells and to produce high strength aluminium alloys of value, for example, in the aerospace industry. Scandium is often grouped together with the rare earth elements (REE). Amongst others, scandium can be found in bauxite residues, so called red mud. It is possible to extract and enrich scandium from red mud by leaching and solvent extraction. Scandium can then be recovered from the pregnant strip liquor by crystallization. The strip liquor will however still contain certain impurity elements. In the present work, a method for obtaining a pure scandium solid phase by direct crystallization from the strip liquor is evaluated. It was found that Fe and Ti co-precipitate with Sc under the conditions employed.

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By Xuewei Lv

An intelligent recognition and quantification system for the micrographs iron ore sinter was developed in the current paper. The average distribution parameters in a gray histogram of minerals by a Gaussian gray distribution model were obtained. The feature curves of the gray histogram of two minerals were achieved by combining the two density functions. The feature indexes, such as the number and position of the peaks and the valleys of two minerals in different ratios, were quantified by differentiating the distribution functions. This algorithm is able to extract the feature of the minerals adequately and accurately for recognizing the composition and phases of the minerals intelligently.

Jan 1, 2009

By Chidchai Loyprasert, R. A. Stoehr

"A computer model has been developed to predict grain structures in alloys solidified under unidirectional flow using a combination of three techniques -- solution of the equations for flow of an incompressible fluid bounded by curved surfaces by the SOLA-SURF algorithm, calculation of heat flow by a finite difference method, and simulation of grain formation by a two-dimensional cellular automaton (CA) model. The changing rigid surface has been taken into account. Heterogeneous and homogeneous nucleation are considered, and the growth kinetics of a dendrite tip are evaluated by the Kurz-Giovanola-Trivedi (KGT) model. These calculations were applied to solidification of an Al-4.5% Cu alloy flowing over a chill on the bottom of a channel, a system for which experimental results were available. Using a variety of flow rates and superheats, agreement between the computed and experimental results were very good including transitions between columnar and equiaxed grains, the aspect ratio of the grains, and the inclination of the grains to the flow.IntroductionModeling of casting and solidification processes has developed over the years along two distinct tracks: (1.) modeling of macroscopic heat transfer and fluid flow for design purposes, and (2.) modeling of microscopic processes such as nucleation and growth in order to improve the scientific understanding of the phenomena involved. The present work is an attempt to combine the macroscopic and microscopic approaches for the solidification of an alloy flowing over a chill. The specific case chosen is that of an aluminum-4.5 % copper alloy flowing linearly over a water-cooled copper chill for which experimental results were available over a range of flow rates and superheats. For the macroscopic calculations, the SOLA-SURF algorithm for solution of the twodimensional fluid flow equations was combined with the finite difference method (FDM) for calculating heat transfer. For the microscopic calculations, heterogeneous and homogeneous nucleation were considered, and the growth kinetics at the dendrite tips were evaluated. The cellular automaton (CA) technique was used to apply the microscopic kinetics to the temperature and .flow conditions."

Jan 1, 1999

By Robert E. Moore

Renewed interest in olivine refractories has led to efforts to characterize them employing modern techniques of experimentation and data analysis. Initial studies have focused on determination of physical and thermophysical properties. Special equipment for the determination of thermal shock resistance and creep behavior have been constructed. Optimal compositions for maximizing various properties are being identified using appropriate statistical techniques. The overall goal is to develop response surfaces for each of a selected group of engineering design and use properties. Development of ?olivine Refractories? in the United States The term "olivine refractories" is used here because it does appear that domestic deposits of this rock will be the focus of renewed interest and "olivinell is the preferred term in this country. There are extensive deposits of high quality olivines extending through parts of Georgia. North Carolina and in the state of Washington. The eastern olivines are much more localized and extensively altered compared to the western materials. The Washington olivines exist as massive rock deposits in the Twin Sisters mountain area northeast of Seattle and their inaccessi-bility has slowed efforts to develop them. The North Carolina olivines have been used in steel plant applications since the 1930's. Geologists use the term "olivine" to describe assemblages of ortho-silicates. 2RO.SiO2, wherein the RO may be MgO. FeO. MnO. etc. When the RO consists essentlally of MgO and FeO. the material is called dunite and. as such, is synonymous with "refractory olivine." Refractory olivines utilizing North Carolina materials were developed for brick products by Birch and Harvey in this country around the mid-1930's. (I) Their work was completely independent of that of V. M. Goldschmidt and co-workers who used massive dunites located in Denmark. (2) These deposits are currently being mined by A/S Olivine of Denmark for the manufacture of a rather complete line of brick shapes for use in steel-plant. glassplant. and cement kiln applications. Birch and Goldschmidt

Jan 1, 1982

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG, HUI XIAO

Oxygen-rich side blow bath smelting (OSBS) technology was developed in 2000 based on Vanyukov process. This technology exceeds the traditional pyrometallurgical methods by its great processing capability, high metal recovery and environmental-friendly property. In the past 15 years, OSBS technology extended its application area from lead industry to bismuth, antimony and waste recycling industries, etc. This paper introduces the history and new developments of OSBS technology. The typical industrial applications examples of the OSBS technology in China, including high lead slag reduction, low grade bismuth-lead concentrate smelting and metallurgical waste recycling, are reviewed. Especially, the unique furnace properties and technical parameters are compared. Finally, the potential research directions of OSBS technology are summarized.

Jan 1, 2016

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By Steven I. Baskin

Cyanides are utilized in many industrial applications including preparation of chemical intermediates, electroplating, and' mining, Cyanide has been utilized in chemical warfare operations as well Cyanide is also synthesized and found in plants and animals including man where it is thought to perform multiple functions. A variety of enzymes are known to detoxify cyanide under different conditions. These include rhodanese, 3-mercaptopyruvate-sulfur transferase, thiosulfate reductase, cystathionaseand albumin. Cyanide appears tQ exert its toxic effect primarily by inhibiting cytochrome oxidase? although other enzymes are also inhibited. Therapeutic antagonist categories to treat cyanide include methemoglobin formers such as nitrite, sulfane-sulfur donors such as thiosulfate, metal salts or complexes such as cobalt and cyanohydrin-forming compounds such as dihydroxyacetone or alpha keto-glutaric acid. Advantages and disadvantages of each category will be discussed. Newer compounds under development have been found that may allow for prophylactic therapy for cyanide poisoning with minimal side effects; In addition, portable co-oximetry devices may provide real-time measurement of cyanide in field units.

Jan 1, 1998

By M. R. Jolly, J. -C. Gebelin

"A number of different types of so-called ""filters"" are used in the metal casting industries to impart some cleaning effect and flow control on the liquid metal as it passes through them. The filters range from simple planar meshes through extruded channels to reticulated foam structures and they are manufactured from a range of material going from metals to glass or ceramics. It is most common that software packages used in the industry model the filters by a simple pressure drop associated with some area fraction and permeability parameters.Recent experimental work at the IRC in Birmingham [1] has shown that filters of the same type can behave very differently depending upon the casting process in which they are employed. Modelling filter geometries for a range of different casting processes has indicated that the flow of metal and heat losses through the filters are rather complex and should be considered when using filters in the casting processes. This paper will present a number of cases of different types of filters modelled and different processes and indicate some of the sensitivities of the processes to boundary conditions imposed by the process.IntroductionFilters are commonly used in the foundry industry. The real action of the filters on the liquid metal is not really understood. Some filters are claimed to have a chemical action on the liquid metal or to be able to clean the metal by stopping the impurities or oxides that will result in inclusions in the cast part. However, some recent experiment carried out at the University of Birmingham in investment casting and results available on sand casting [2] have shown that the action of filters may be different in these two processes. As the main difference between these two processes is the mould temperature, the hypothesis of a partial solidification of the metal in the filter occurring in the sand casting process during the primary stage of the filling has been advanced, whereas there is little or no solidification in investment casting. In order to verify this hypothesis, and to reach a better understanding of how filters work, a numerical investigation of the flow and heat transfer in filters in both sand and investment casting has started at the University of Birmingham, in the framework of the FOCAST project. The FOCAST project is an EPSRC project aimed to increase the understanding of the investment casting process. Another issue is the way the simulation packages predict the influence of the filters on the metal flow. The filters are most of the time modelled as porous obstacles characterised by a pressure drop calculated from porosity and some surface ratios or proprietary coefficients. This paper will present the preliminary results of this numerical investigation. First, the different models that have been used are presented, followed by the obtained results. A discussion of these results and their perspectives conclude the paper."

Jan 1, 2001

By Gui-fang ZHANG, Zhe SHI, Lei GAO

Secondary V-recycling slag, an industrial waste containing high gallium is being dumped continuously, which causes the loss of gallium. Thus, the alkali fusion process was employed to recover gallium from this slag. The effects factors on extraction of gallium such as roasting temperature, roasting time, alkali fusion agent concentration and CaO concentration were investigated in the paper. The experimental results indicated that excessive roasting temperature and roasting time is unfavorable to the recovery rate of gallium. The appropriate roasting temperature and duration are 1000 and 2 hours, respectively; The appropriate proportioning of Na2CO3: NaOH is 2:1 when the concentration of alkali fusion agent weighs 0.4 times the mass of the slag; In order to remove SiO2 from the leaching liquor, CaO should be used as an additive in the roasting process. The appropriate concentration of CaO should weigh 0.2 times the mass of the slag. Employing these optimal alkali fusion conditions in the roasting process, gallium recovery is above 90%

Jan 1, 2015

By F. Robert Hubbard

IMCO Recycling Inc. has developed a new, patented technology for the production of fertilizer, K-SOIL?, as a by-product of its aluminum recycling operations. This new technology can substitute for conventional technology which now results in a saltcake residue that is placed in 'landfills. Four years of research and development work by IMCO culminated in a U. S. patent issued April 5, 1994. As part of the technology development effort, IMCO engaged the services of a nationally renowned research organization and a prominent university. These two organizations have conducted in-depth agronomy studies In the laboratory, greenhouse, and the field. Results have shown K-SOIL? to be performance equivalent, on a nutrient content basis, to conventional potash fertilizer. The first field applications on commercial farms were made in the spring of 1994. K-SOIL? is a potassium-bearIng, granular solid which may find use in fertilizer blends, direct application, and other forms of fertilizer products. The overall benefit of this new technology is to create a useful by-product rather than generate a useless residue and, thereby, reduce or eliminate the amount of salt cake now placed in landfills. As such, It is a significant, step toward IMCO's ultimate goal of complete recycle.

Jan 1, 1995

By Sudhir C. Dhara

An attempt has been made on the concentration of Platinum Group Metals (PGM) from the converter matte material by microbial .leaching. Biological oxidation of base metal sulfides such as iron, copper, nickel and free sulfur present in the matte material using Thiobacillus ferrooxidans is an alternative method to concentrate the PGM-and gold. The method which produces a platinum group metals concentrate is comparable to chemical processes and electrochemical process.

Jan 1, 1995

By Tuomas Hirsi

The world’s first large scale modular solvent extraction plants have been delivered by Outotec. The first of these is now in operation and has proven that the VSF®X technology can deliver the excellent performance of the Outotec VSF® solvent extraction process. Modular delivery allows site work to be minimized and the manufacturing done in a controlled environment, allowing for serial production manufacturing benefits. Container based delivery was found to be a highly efficient way of utilizing the standardized transportation methods on a global scale. Site work with modular units was found to be efficient and highly predictable. In this paper, we present the first successful Outotec VSF®X deliveries and discuss the benefits of the modular delivery and design compared to the standard solvent extraction installation’s delivery. The process performance of the VSF®X is also discussed with experiences from the first industrial reference presented.

By Xuemei Zheng, Aiyuan Ma, Yonggang Zuo, Jinhui Peng, Shiwei Li, Libo Zhang

The effect of moisture content on the dielectric properties and microwave drying behavior of zirconium hydroxide was studied by using an open-ended sensor dielectric measurement system at the frequency of 2.45 GHz. The experimental results showed that moisture content can significantly influence the variation of dielectric properties. Dielectric constant, loss factor and loss tangent all increase with the increasing moisture content. Compared with the conventional drying method, the microwave-assisted drying method resulted in a substantial decrease (81.8%) in the drying time, and the drying effect was better at the lower power level of 600 W. This study offers the useful information on dielectric properties of zirconium hydroxide, which can be used for developing microwave drying applications in mineral processing and designing better microwave sensors for measuring zirconium hydroxide moisture content.

Jan 1, 2015

By Larry Twidwell, Ed Rosenberg, Courtney Young, Sean Dudley, William Gleason, Maureen Chorney

Experimental and industrially produced polystyrene and silica resins are tested for recovery capabilities of Rare Earth Elements (REE). Testing regimes being used are typical of resin analysis. Inductively Coupled Plasma-AES results indicate that preferential separation and recovery is possible in the adjusted pH range of2 to 10, solution conditions, and resin type. Testing conditions are resulting in structure modification of the composite resin as indicated by X-Ray Diffraction, Differential Scanning Calorimetry, Scanning Electron Microscopy, Mercury Porisometry, and density analysis. Resin modification indicates both surface and internal structure alteration outside of reported standard behavior of resins. Structural changes have ramification for both Rare Earth Recovery RER and traditional resin operations. Analysis shows that the resin uptake of REE can be manipulated for concentration. Further analysis with SEM work indicates that widespread surface and interior modification is taking place as resins load with REE. This modification is leading to pore rupture and particle breakage. Further investigation is being performed to determine the mode of breakage.

Jan 1, 2015

By J. David Chapman

There are a variety of choices of materials for mineral extraction processing. Traditionally, end users have used metallic piping for fluid handling and little is known about the advantages (or limitations) of non-metallic piping systems. This presentation will review custom FRP pipe systems and their use in severe corrosive and erosive process streams. These systems can be designed to various pressure and temperature ratings and different components (such as resin and glass type) can be varied to suit the process conditions

By Markus A. Reuter, Jacob Wood, Robert Matusewicz

Over the last 20 years, significant improvements in copper smelter productivity have been realized through the advent of continuous smelting processes. This progress has until recently however, not been carried through to copper converting. Peirce-Smith converting has been widely used by the copper industry for 100 years but is limited by its batch nature in achieving large scale of production. A logical next step is therefore copper converting on a continuous basis with its inherent environmental benefits. A number of continuous converting technologies are currently in use or being developed within the copper industry, the majority of these operating with calcium-ferrite slags. A notable exception however is the Ausmelt Continuous Copper Converting (C3) technology which has focused on operation with ferrous-calciumsilicate or loosely called olivine type slags. This paper discusses the merits of the Ausmelt C3 process and the advantages offered in terms of operational flexibility and process control arising from the use of lime modified iron silicate slags. It also examines the effects of key process variables pertinent to continuous copper converting from both a theoretical and experimental/operational perspective.

Jan 1, 2009