Search Documents

By K. Prashant Sarswat

Isotopes are critical to a variety of applications including physical science analyses, biology, medicine, pharmaceuticals, and national security. In most cases isotopes must be relatively pure or highly enriched before they become useful. Current isotope separation technologies are relatively inefficient, capital and labor intensive, and often produced by a limited number of suppliers. In the category of isotopes, lithium is among other important candidates. Lithium is found naturally in two isotopes, 6Li which accounts for 7.5% of all lithium, and 7Li which makes up the balance of 92.5%. Each of these isotopes is important to the nuclear industry. 7Li is often used in the form of lithium hydroxide which is used to control pH in pressurized water reactors. The current supply of 7Li is based mostly outside of the United States, and its long-term supply is uncertain. Apart from supply issues, the use of mercury for 7Li separation is also a concern in commercial processing using the most common and efficient approach [1–3]. Hence, a reliable, environmentally friendly, and efficient technique is needed to produce 7Li. In this line of investigations, the authors used a two-compartment system and significant separation was achieved. In this piece of research, some preliminary results are presented including cell design and actual isotope ratio after enrichment. Applying an electro-potential across two electrodes can be used to drive electromigration of Li isotopes. The electromigration is in addition to normal diffusion. Note that 6Li diffuses faster and hence there will be a lowering of the 6Li concentration near the positively charged electrode and an enhancement in 6Li near the negative electrode during the separation process. Similarly, 7Li will be more prevalent near the positive electrode and less prevalent near the negative electrode during the initial separation stage [1].

By Wing Ka Ng

Substitution of pulverized coal injection by solid biocarbon fuel has the potential to achieve substantial reduction in GHG emissions associated with blast furnace ironmaking. A systematic evaluation was conducted on the performance of solid bio-carbons produced from a single raw biomass source using different pyrolysis technologies. The potential of solid biocarbon in reducing GHG emission of the blast furnace ironmaking process is strongly influenced by its O/C mass ratio. In order to achieve substantial GHG reduction, it is necessary to replace coal injection by solid biocarbon having a low O/C mass ratio. The pyrolysis technology and conditions employed are key parameters influencing O/C mass ratio of the resultant solid biocarbon. Close collaboration between steelmakers and solid biocarbon producers is critical for producing suitable solid biocarbon fuel to replace pulverized coal injection. A successful partnership should pave the way in achieving substantial reduction in GHG emissions of the blast furnace ironmaking process.

By Jan Smit

Sulphidic copper concentrates are generally processed by pyrometallurgical means; while oxidative pressure leach processing of such materials has been shown to be technically feasible, there has traditionally been little incentive to choose this route in favour of a smelting option. However, for concentrates with elevated arsenic levels, oxidative pressure leaching offers distinct advantages, as smelter air emission standards and restrictions on concentrate importation have tightened. The current state of pressure leach technology allows for high copper extractions from arsenical copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. In its studies on pressure leaching of copper concentrates, Sherritt has shown that arsenical feed materials can be converted into environmentally stable residues, with excellent copper extractions. The results of recent batch and pilot plant test work are discussed, including the deportments of copper, arsenic and precious metals.

By Edwin Adoyi Ali, Zainab Shehu Aliyu, Adele Dzikwi Garkida, Muhammad Dauda

Feldspar from Matari, Nigeria was analyzed using SEM, XRD and XRF techniques for microstructural analysis, mineral phase analysis and chemical composition analysis respectively. Qualitative and quantitative XRD analyses revealed the presence of microcline 59.6%, albite 34.7% and quartz 5.71%. The XRF results showed that the feldspar contains 67.32% SiO2, 17.54% Al2O3, 11.33% K2O, 2.75% Na2O, 0.12% CaO, 0.01% MgO, 0.02% MnO2, 0.10% Fe2O3, 0.00% Ti2O, etc and 0.14% LOI. SEM/EDX analysis shows the presence of microcline feldspar as the dominant phase, exhibiting lamellar twinning. The XRD has also revealed that potash has the highest peak, indicating its high concentration. The 0.10% Fe2O3 present is within the permissible level (0.1-0.3%) for glass making and also within the potash feldspar specifications (0.17%). The Matari feldspar is a microcline type, rich in potash, alumina and silica, enabling it meet the standard specifications for alumino-silicate glass.

Jan 1, 2015

By Animesh Jha

The carbothermic reduction of chalcopyrite has been studied in the temperature range 1073 to 1273K in presence of lime. The role of lime during the reduction process is explained and the phase equilibria leading to the metallisation of copper and iron are discussed. The effect of coal and carbon monoxide on the reduction process have been studied and the rate governing steps are identified. This investigation also cites examples of possible mechanisms of physical separation of metallic Cu from iron during the reduction process.

Jan 1, 1992

By J. -P. Nepper

It has been possible to largely contain converter aisle emissions of SO2 and fumes in the case of batch-wise operated Peirce Smith converters during normal blowing periods with the help of suitably designed primary hoods. Controlling the escape of off-gas during the periods of turning the converter in or out of the stack has been problematic in the past. Effective automated contro1 systems have been deve1oped for the purpose and successfully applied in smelter operations in Spain, Taiwan and Germany. This has led not only to an effective reduction of emissions in the converter environment but also to an improvement in the converter operation.

Jan 1, 1992

By Yuanbo Zhang, Guihong Han, Guanghui Li, Tao Jiang, Zengqing Sun, Yanfang Huang

"Because of small specific surface area and poor ballability, vanadium/titanium-bearing magnetite is difficult for production of oxidized pellet. A novel organic copolymer binder, modified humic acid (MHA), has been authorized recently in China. Effects of the novel MHA binder on the quality of V/Ti-bearing magnetite pellets are studied in this paper. Experimental results show the MHA binder can obviously improve the strength of green pellet. Because of better heat endurance, the MHA binder pellet has a higher strength than Peridur pellet under the same preheating conditions. Moreover, TFe grade of pellet with the MHA binder is much higher than that of the bentonite pellet. The strength of preheated pellet containing MHA binder of 0.25%~1.0% meets the requirements of oxidized pellet production by grate-kiln process. Comparatively, MHA is a promising orgainc binder for iron ore pellets. Its price is only one tenth of Peridur price and about 3 times of bentonite price.IntroductionThe iron-making practices show that the use of pellet is beneficial to blast furnace life, productivity and fuel savings. Therefore, many iron-making plants have expanded the production of oxidized pellets in order to meet the needs of modern large-scale blast furnaces [1]. Presently, bentonite is widely used to improve the quality of iron ore pellets. The negative effects of using bentonite include decreasing total iron (TFe) grade and degrading the metallurgical properties of the final products [2, 3]. Many studies, therefore, have been conducted on the application of organic binders to overcome the weakness of the inorganic bentonite. In comparison with inorganic binders, one of the biggest strengths of organic binders is low residual silica content [4]. However, those studies showed that the economics of foreign organic binder addition into pellets was not attractive. For example, the compression strength of preheated pellets and roasted pellets are both too low, resulting in powder generation and ring formation in the industrial rotary kiln [3, 4]."

Jan 1, 2011

By Xudong Liu, Feng Chen, Yufeng Guo, Wei Chen, Tao Jiang

Willemite is typically found in oxidized zinc ores and metallurgical secondary resources but without effective extraction method yet. Based on the ideas of zinc phase reconstruction in the willemite, the extraction of zinc from willemite by calcified-roasting using CaO as additive and ammonia-leaching process was studied in this paper. The influences of CaO dosage, roasting temperature, roasting time on the phase transformation and zinc leaching rate were studied, which were characterized by XRD. The results indicated that Zn2SiO4 was transformed into ZnO or Zn2CaSi2O7 .After roasted with 1.4 times of theoretical CaO dosage at l280 for 40 minutes, willemite was thoroughly transformed into ZnO. The zinc leaching rate of the roasted sample was 97.45% in NH4Cl-NH3 H2O leaching system, which increased by 91.40 % compared with zinc leaching rate of 6.05% when willemite was directly leached in NH4Cl-NH3 H2O system.

Jan 1, 2016

Thallium is a very minor element found in lead ores. It's behaviour during lead smelting has recently become of much greater interest due to the effects it had on the health of waste heat boiler maintenance contractors at a Canadian smelter. In this paper the behaviour of thallium in both traditional and direct lead smelting processes will be examined using computational thermodynamics techniques. Yazawa and his coworkers have made extensive use of computational thermodynamics to examine and illustrate pyrometallurgical processes. It has been shown that thallium behaviour during smelting is strongly influenced by the extent of oxidation of the lead concentrate and by the presence or absence of chlorine in the charge. The condensation behaviour of thallium species in the waste gas handling system was also modelled and it has been confirmed thallium-rich deposits can form at the high temperatures prevailing in waste heat boilers.

Jan 1, 2003

By Stéphane Bourg

The SCRREEN project gathers more than 50 European initiatives, associations, organisations or independent experts working on Critical Raw Materials (CRM) into a long-lasting network including stakeholders, public authorities, and civil society representatives. SCRREEN contributes to improve the CRM strategy in Europe by (i) mapping primary and secondary resources and substitutes of CRMs, (ii) estimating the expected demand of various CRMs in the future and identifying major trends, (iii) providing policy and technology recommendations for actions improving the production and the potential substitution of CRM, (iv) addressing specific waste electrical and electronic equipment (WEEE) and other End-of-Life (EoL) product issues related to their mapping and treatment standardization, and (vi) identifying the knowledge gathered over previous years and making the data accessible to those beyond the project. As a first step, SCRREEN worked at providing stakeholders with a comprehensive analysis of the current use of the CRM, the mapping of potential primary and secondary resources, and identification of the key technologies used in their production. Substitution profiles, analysis of European business and policy issues pertinent to CRMs, and an identification of the standards, policies, and regulatory frameworks concerning these CRM was also completed. In a second step, to be conducted between mid-2018 and mid-2019, SCRREEN will provide guidance for improving the CRM market in Europe by identifying opportunities from research, development, and innovation (R&D&I) that could reduce the supply and/or economic risks around the most relevant CRM for Europe.

By Lv Guozhi, Niu Liping, Shi Guanyong, Liu Yan, He Jicheng, Du Yanjun, Dou Zhihe

"We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The alloy prepared in different process conditions was characterized via XRD, SEM, OM and TEM and metallographic microscope, in which the existing state and micro-structural defects of inclusions are analyzed. The results show that there are three distinct regions: copper-rich regions, chromium-rich regions and the inclusion regions. Inclusions are mainly in the form of stomata and Alz03 phase, mainly locating in the copper-rich phase and the interface area of chromium-rich phase and the copper-rich phase. Adding Na3AlF6 and heating agent can effectively reduce the inclusion content in the alloy.1 IntroductionIn recent years, with the development ofhigh power vacuum and high-pressure technology ,the CuCr alloy contact material which has many advantages gradually replaced the traditional W-Cu and Cu-Bi series alloy contact material, and become the first choice of material in high-voltage and high-power vacuum switch contacts['-3l. The traditional powder metallurgy method, infiltration method and vacuum arc melting method[4-SJ are using metal Cu powder and Cr powder as raw material by casting molding, and have disadvantages such as high production costs, complicated process, poor product density and low yield, especially in the large size alloy ingots[9-12l. At present, the world regards CuCr alloy new preparation technologies as the first place, and how to achieve a large size the CuCr alloy ingot preparation has become a hot research of CuCr alloy[3l. Zhang Ting-an and Dou Zhihe[l-3l who are supported by national natural science fundation of china successfully successful developed new technologies and core equipment to prepare large-size copper-chromium alloy through aluminum thermal reduction-secondary refining method, and obtained two national invention patents. The method includes two key steps: one is get CuCr alloy consumable ingot by Thermit-SHS with electromagnetic stirring, the other is to refme the CuCr alloy ingot to remove the pores, inclusions and other defects by electroslag remelting technology to get dense and uniform CuCr contact material. The preliminary study results show that means of electromagnetic stirring evidently inhibit effect of alloy ingot macrosegregation during the electromagnetic casting stage, but there are still microstructure defects such as alumina inclusions and pores in the alloy ingots. Therefore, Zhang Ting-an et al refer new ideas of using the electroslag remelting to refine Cu Cr alloy ingots and effectively remove the defects of the ingots such as pores and inclusions [3l _ At present, there is no report of study on the electroslag remelting refining processes of CuCr alloy (the refining slag, remelting current). This article will research mode of occurrence and distribution law of inclusions in the large-size CuCr alloy ingots by Al Thermit-SHS under magnetic field stirring action and provide a theoretical basis for chosing refining slag to remove inclusions by electroslag refining. Meanwhile the article analyses the effect of reduction conditions of Thermit-SHS on the types of inclusions, mode of occurrence and distribution of regular inclusions in alloy ingot, and refer theory for inclusions regulation in the large-size alloy ingots."

Jan 1, 2013

By Hiroyuki Matsuura, Fumitaka Tsukihashi

"Emission of CO2 gas from steelmaking industry covers more than 12 % of total CO2 emission in Japan. Though many efforts have been made to curtail energy consumption and high energy efficiency of Japanese steel production process has been achieved so far, further reduction of CO2 emission is strongly requested to develop sustainable steel production process and produce “green material”. Recently, authors have proposed the innovative hydrogen production process, in which water vapor is reacted with discharged steelmaking slag to produce hydrogen gas. This reaction can be achieved without any external energy source and operated by huge thermal energy associated with steelmaking slag and FeO or unrecovered Fe droplets that are relatively rich in the slag. In this paper, thermodynamic calculation results with various initial conditions in terms of hydrogen productivity were presented. Laboratory-scale experiments were also conducted to clarify the validity of thermodynamic calculation and the reaction rate in realistic conditions.IntroductionIronmaking and steelmaking process from iron ore through blast furnace and BOF is an essential steel production route for Japanese steel industries to supply high quality steel products in large quantity to society stably. Blast furnace – BOF process requires huge amount of fossil fuels such as mainly coal, resulting the emission of considerable amount of CO2 gas. Since the emission of CO2 gas from steel industries, about 147 Mt (FY2011), accounts for approximately 12 % of domestic CO2 gas emission in Japan (FY2011),[1] it is an urgent issue for steel industries to develop environmental-friendly ironmaking and steelmaking process and reduce CO2 emission. Various kinds of gases and by-products generated from ironmaking and steelmaking processes have been recycled as much as possible at present. Enormous thermal energy is also generated from processes and released to surrounding atmosphere as various forms such as sensible heats of gases, molten steels or by-products, and as heat losses. However, these energies are not utilized before final dissipation to atmosphere. Although various technologies to utilize thermal energy from ironmaking and steelmaking processes have been attempted to develop, practical application of these technologies has not been achieved because the thermal energy is not always useful as an energy source. In steelmaking process by BOF, fluxing agent such as CaO is added during reefing and thus about 100 kg/t-steel of steelmaking slag are generated. Since the steelmaking slag is discharged at temperature range between 1873 and 1923 K after discharge of refined molten steel, it also has large thermal energy. Amount of generated BOF slag is 11.0 Mt/y (FY2012) in Japan.[2] Assuming the amount of steelmaking slag is 10 Mt/y and its average heat capacity from room temperature to 1923 K is 1 kJ/kg·K,[3] unutilized heat is estimated to be 16 PJ/y, which is equal to annual energy consumption of 420 thousand families in Japan.[4]"

Jan 1, 2014

By Florian Kongoli

"Lime ferrite" slag with limited silica content has proven to be a valuable choice in the modem processes of copper smelting and converting due to several advantages that this slag offers compared to classical silicate slags. Nevertheless the liquidus surface of this slag has been experimentally measured only at low oxygen potentials such as in equilibrium with iron or near it and in air. Although most of the smelting and converting processes that use this slag occur at intermediate oxygen potentials, the liquidus surface of this slag is not known at these conditions and the effect of oxygen potential and silica has not been correctly understood. This has brought some confusion in literature as well as in the industrial practice. In this work the liquidus surface of the calcium ferrite slags has been quantified by the means of a new thermophysicochemical model and a new type of liquidus surface diagrams which are very convenient for any industrial process that uses calcium ferrite slags. These diagrams can be easily used to select the lowest liquidus temperature of calcium ferrite slags at a minimum cost and can help design several fluxing strategies in copper smelting and converting processes. The effect of the oxygen potential and silica is also quantified and important industrially related conclusions are drawn.

Jan 1, 2003

By Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie

In the present study, the oxidation process of vanadium and chromium bearing hot metal was investigated by using CaO-FetO-SiO2 slags at 1653K in MoSi2 furnace. The results indicated that both the vanadium distribution LV and chromium distribution LCr were of the orders of 2.2~2.4 with the basicity range of 1.32~1.78 and FeO weight percent range of 28%~45%. Both LV and LCr decreased with increasing basicity and decreasing FeO weight percent. The phosphorus distribution LP was of the order of 1.34~1.56. However, LP increased with increasing basicity and decreasing FeO weight percent. The oxidation ratio values of V and Cr in hot metal were above 84% and the values of P were nearly 50%. In other words, it means the addition of CaO in vanadium slag provided a certain ability of dephosphorization along with keeping high oxidation ratios of V and Cr.

Jan 1, 2015

By Shaohua Ju, Feng Jiang, Chuanhua Li, Jinhui Peng, Libo Zhang

A T-junction microchannel is proposed to overcome the existing problems in conventional solvent extraction of indium from zinc hydrometallurgical process. Experiments were performed to separate In3+, Fe3+ and Zn2+ from sulfate solutions using Di-(2-ethylhexyl)phosphoric acid (D2EHPA) as the extractant. The effect of parameters such as pH, microchannel size and contact time on the extraction behavior of In3+, Fe3+ and Zn2+ was investigated. At contact time of 2.52 s and initial solution pH of 0.48, the extraction efficiency of In3+, Fe3+ and Zn2+ was 99.13%, 8.31% and 2.45%, respectively and separation factor of In3+/Fe3+ and In3+/Zn2+ were almost 1229.54 and 4864.98, respectively. Then, the loaded organic phase was stripped in T-junction microchannel. At contact time of 33.6 s, 99.64% of stripping efficiency of In3+ and stripping equilibrium were reached, while concentration of Fe3+ and Zn2+ was lower than 0.01 g/L with good separation of In3+ from Fe3+ and Zn2+.

Jan 1, 2016

By Yuanbo Zhang, Zhixiong You, Guanghui Li, Peidan Wen, Tao Jiang

Sn-bearing iron ore containing small amount of Zn, Pb and As is one of the typical complex polymetallic ores in China. This kind of ore is not extensively utilized due to the complicated relationships between iron and other associated nonferrous metal minerals. Excessive contents of these elements would adversely affect the metallurgical operation as well as the quality of steel products. In this study, reduction behavior of Sn was detailedly investigated using H2 or mixed H2/CO as reductant. The results revealed Sn volatilization was improved in the presence of H2 than individual CO/CO2 atmosphere. Simultaneous volatilization of these elements was realized by roasting under weak H2/CO reducing potential, and metallization reduction was advantageous for further Zn volitilization. A metallic pellet (DRI) with Fe metallization greater than 90%, residual Sn, Zn, Pb and As content of 0.054%, 0.012%, 0.0045% and 0.09% was prepared via a simulated reducing gas of coal gasification.

Jan 1, 2015

By Yuanbo Zhang, Yingming Chen, Zijian Su, Bingbing Liu, Jun Chen

Iron, tin-bearing tailings is a kind of hazardous solid waste generated from cassiterite dressing operation. It is difficult to utilize the tailings by present mineral processing methods due to the complex dissemination characteristics. In this study, a process of gas-based magnetizing roasting followed by magnetic separation was studied for separating and recovering iron from the tailings. The effects of roasting and magnetic separation parameters on the recovery of iron were systematically investigated. The optimum parameters were proposed as follows: CO/(CO+CO2) content of 5%, roasting temperature of 850 C, roasting time of 60 min, grinding particle size of 90% less than 45 μm and magnetic field intensity of 800 Gs. Under these conditions, the magnetic concentrate containing 68.5% Fe and 0.06% Sn was achieved, which can be used as high-quality raw materials for direct reduction iron production.

Jan 1, 2016

By J. Brent Hiskey

The global copper industry faces a technological challenge to develop processing schemes for more complex and impure ores and concentrates. Group 15 elements (As, Sb, and Bi) represent impurities that are troublesome both in terms of environmental impact and metallurgical processing. The so-call "dirty" copper concentrates are either unacceptable for smelting and refining or incur high penalties. The behavior of the Group 15 elements is of critical importance in maintaining product quality and process performance. During copper electrorefining, these impurities are released to the electrolyte by electrochemical dissolution of the anode. Depending mainly on temperature, concentration, and oxidation state these elements can spontaneously coprecipitate from the electrolyte. Some of these precipitates are referred to as floating slimes and their formation can have extremely detrimental effects on cathode purity. In this paper, the mechanism of floating slimes formation will be discussed and the fundamental thermochemistry will be reviewed and analyzed in relation to solubility properties.

Jan 1, 2012

By I. H. Bonekamp

Norddeutsche Affinerie has operated an Outokurnpu type flash smelter for more than 25 years. In recent years, the concentrate smelting capacity was increased to 750,000 tpy, double of the initial design capacity. Maintaining this high performance level requires very good metallurgical process control. It is not enough to base this control on thermodynamics and kinetics since the furnace is highly dynamic. Understanding these dynamics and being able to quantify them can have significant financial benefits. A mass and energy balance model was developed and is discussed based on measured data. At this time the model is based on the major elements copper, iron, sulfur and silica. With it is possible to quantify the differences of the various material streams such as matte, slag, flue dust, matte carry-over to settling furnace, etc. Comparing the reconciled energy balance model with the fundamental thermodynamic model makes it possible to quantify the dynamics. These dynamics are related to input parameters using methods such as statistics and neural nets. In the future this database will be used to improve the understanding of the dynamic process as well as the dynamic process control.

Jan 1, 1999

By Xue Wang, Callie Babbitt, Chelsea Bailey, Matt Ganter, Gabrielle Gaustad, Brian Landi

"Current trends, motivated by fossil fuel dependence and unprecedented greenhouse gas (GHG) emissions, show lithium-ion batteries (LIBs) emerging as a competitive energy storage technology due to higher power and energy densities compared to Pb-acid and Ni-metal hydride chemistries. These trends may be of concern, however, as environmental impacts are not well understood for either the LIB itself, or for the nanoparticles consumed or released during the battery's production, use, or end-of-life. This study combines economic modeling, dynamic material flow analysis, and fundamental material characterization methods in order to quantify some of the economic and environmental trade-offs for LIBs at their end-of-life. As expected, results show that as chemistries transition from Li-Co based cathodes to Li based Fe, Mn, and S cathodes, LIB recovery value correlates to the value of the raw materials used. These initial results aim to inform collection policies being proposed currently as well as enable future deployment of novel recycling techniques.IntroductionGlobal fossil fuel dependence and unprecedented GHG emissions have led to increasing attention on energy alternatives, for both electricity production and personal transportation. However, development of renewable energy systems is contingent on concurrent technological development of energy storage systems, primarily batteries used for power grid load-leveling, renewable energy storage, and hybrid and battery electric vehicles. In this sector, lithium-ion batteries (LIBs) are emerging as a competitive technology due to higher power and energy densities compared to lead-acid and nickelmetal hydride chemistries[!]. LIBs represent close to 20% of the total rechargeable battery market and 75% of the portable rechargeable battery market, which is the fastest growing segment of the rechargeable battery market, with a 20% global growth in 2008 [2].This surge in production ofLIBs indicates a looming waste problem; total waste from Li-ion batteries has likely grown substantially from the 500 metric tons estimated in 2003 [3]. Figure IA shows the substantial increase in world-wide lithium production that has occurred in the last several decades with batteries making up the largest share of applications (Figure lB). California and New York state legislators have attempted to proactively address this looming waste by issuing diposal bans on rechargeable batteries in their states[4, 5]. However, quantification of the costs involved in collection, transportation, and processing of these materials has not been examined in depth."

Jan 1, 2012