Search Documents

By C. T. Yavuz

Higher environmental standards have made the removal of arsenic from water an important problem for environmental engineering. Iron oxide is a particularly interesting sorbent to consider for this application. Its magnetic properties allow relatively routine dispersal and recovery of the adsorbent into and from groundwater or industrial processing facilities; in addition, iron oxide has strong and specific interactions with both As(III) and As(V). Finally, this material can be produced with nanoscale dimensions which enhance both its capacity and removal. The objective of this study was to evaluate the potential arsenic adsorption by nanoscale iron oxides, specifically magnetite (Fe3O4) nanoparticles. We focused on the effect of magnetite particle size on the adsorption and desorption behavior of As(III) and As(V). The results show that the nanoparticle size has a dramatic effect on the adsorption and desorption of arsenic. As particle size is decreased from 300 nm to 12 nm the adsorption capacities for both As(III) and As(V) increase nearly 1000 times. Interestingly, this increase is more than expected from simple considerations of surface area and suggest that nanoscale iron oxide materials sorb arsenic through different means than bulk systems. The desorption process however, exhibits some hysteresis with the effect becoming more pronounced with small nanoparticles. This hysteresis most likely results from a higher arsenic affinity for magnetite nanoparticles. This work suggests that magnetite nanocrystals and magnetic separations offer a promising method for arsenic removal.

Jan 1, 2006

By M. Kawakami

In order to make titanium ingot directly from molten slag, the metal pool was tried to form and used as the cathode. The electro-slag remelting (ESR) unit was used for the purpose. The unit is composed of water-cooled copper mold and the DC power source of 2000 A and 100V. The graphite electrode was used for anode and the base plate was used for cathode. The commercial and re-melted slag of CaO-CaF2 was melted in the mold with the addition of TiO2. The following reactions are expected to occur. Ti4+ + 4e = Ti at cathode 2O2- + 2C = 2CO + 4e at anode During the process, large amount of molten slag splashed out from the mold, showing the CO evolution at anode. The metal deposit was obtained but in the form of block and piled up on the base plate. The metal pool was not obtained perfectly because of shortage of heat supply. The cathodic current efficiency was 60 % at maximum. The metal deposit contained much impurity. In order to reduce the impurity and increase the current efficiency, the effect of electrode distance was examined. The electro-slag re-melting of titanium was tried in order to examine the condition to make metal pool.

Jan 1, 2006

By Józef Czernecki

Chalcocite-bornite concentrates of KGHM contain, similarly to chalcopyrite concentrates, 20-30 wt.% Cu but several times less iron (2-7 wt.%) and sulphur (9-12 wt.%). Another useful characteristic of KGHM concentrates is the presence of organic carbon (5.5-8.5 wt.%) in them, which serves as fuel in the flash smelting process. The main contaminants of the concentrates are lead (1.3-2.5 wt.%) and arsenic (0.05-0.4 wt.%) which require appropriate technological treatment in order to remove them from the copper pro-duct. Chalcocite-bornite concentrates are processed in KGHM by two different processes: ? a flash smelting process (Glogow 2 Smelter) ? a shaft smelting process (Glogow 1 Smelter, Legnica Smelter) The shaft smelting process used in the Glogow 1 Smelter and in the Legnica Smelter has higher production costs than the flash smelting process of HM Glogow 2. Additionally, the shaft smelting process employs several concurrently running installations (six dryers, seven briquetting lines, six shaft furnaces, nine converters), the operation of which, including maintenance, requires significant financial expenditure. Therefore, the Company is currently considering the substitution of the shaft furnace process in the Glogow 1 Smelter and in the Legnica Smelter by the one stage flash smelting process located in the Glogow Smelter, with output equaling the copper production capacity of both smelters, i.e. 320 000 ? 350 000 t/a. There are two technological options being considered which differ from each other in their man-ner of flash slag cleaning. In the first, the slag cleaning would be the same as in the existing Glogow 2 Smelter, i.e. the slag would be cleaned by pyrometallurgical reduction of the oxide copper and other metal compounds in the electric furnace in order to produce waste slag containing below 0.6 wt.% Cu. However, the other option of the flash slag cleaning would be carried out in two stages. After preliminary slag reduction in the electric furnace to 3-5 wt.% Cu, there would be flotation of the partially reduced slag.

Jan 1, 2006

By Bekir Karasu

Boron raw materials are amongst the most important natural sources for many industrial branches and their values become increasingly raised with the discovery of boron usage in many new technological fields. All the countries in the world are unfortunately not as lucky as Turkiye and USA where major boron deposits are mainly located. It is widely known fact that on one side, boron is very precious component with its technological importance, on the other; only its limited sources are available. Therefore, even its wastes have to be evaluated and regained. In the present work wastes of Etibor Kirka Borax Company of Turkiye were used in the production of opaque frits which was suitable for floor tile glazes. Standard and newly produced frit based glazes were applied on the pre-engobed floor tile bodies and single firing was employed. Final products were examined according to the certain standard tests and their microstructures were also investigated. All the results confirmed the evaluation of boron wastes in opaque floor tile glazes.

Jan 1, 2006

By Yves Fautrelle, Kader Zaidat, Hervé Combeau, Miha Zaloznik, Mohammed M'Hamdi, Bachir Saadi, Xiaodong Wang, Knut Omdal Tveito

"Numerical simulations of macrosegregation formation during horizontal solidification of a hypoeutectic Sn-Pb alloy in a rectangular cavity is presented and compared to experimental results. The experiment involves a melting phase, a holding stage at constant temperature with/without application of electromagnetic stirring, and finally solidification. We simulate all stages of the experiment and study the segregation of Pb throughout the experiment. A twophase volume averaged model is used for the numerical simulations, accounting for thermosolutal convection and assuming perfect microscopic mixing (lever rule). The influence of the melting phase and the electromagnetic stirring is studied with different cases to illustrate the consequences on the flow pattern and Pb segregation. The numerical simulations are compared to the experimental data and the impact of chemical inhomogeneities prior to solidification on macrosegregation formation is discussed.IntroductionMany extensive investigations have been performed so far on the solidification of metallic alloys. However, the melting process of metallic alloy has not attracted attention in a same manner. Nevertheless, melting of alloy may put forth peculiar effects as described in the present paper. It has been observed from a benchmark experiment [1, 2] that significant stratification might arise during the melting process of Sn-Pb alloy. That effect was put forth thanks to the analysis of the experimental temperature distribution which indicated that the convective fluid flow was almost zero. The effect was enhanced when the lead composition was higher (above 6wt.%). The present paper is aimed at confirming that the melting of an alloy containing a heavier solute may be accompanied with a stratification of the solute which exerts a stabilizing effect on the convective fluid flow. Results obtained from numerical modeling are compared with experimental data obtained from the benchmark facility."

Jan 1, 2012

By George Grandy

Kvaerner experience is being used to develop software to design or simulate crushing and screening plants. The model techniques discussed are presently being used for open-circuit plants and are being extended to closed circuit plants. The program contains a library of routines, each representing a piece of equipment or unit operation, which are assembled into one of several open-circuit plant configurations. Routines include gyratory primary crushers; standard secondary and shorthead tertiary cone crushers; single, double or triple deck screens; and stockpiles, feed bins and belt conveyors. The program uses steady-state models to simulate the performance of crushers and screens that have small residence times and quickly reach equilibrium when operating conditions and/or parameters are changed. The dynamic aspect of the total circuit model concerns the storage units within the circuit, i.e. stockpiles and bins, and, in the closed circuit configuration, circulating loads and size distributions. In many cases, just vendor's catalog data are necessary for a pre-feasibility simulation; in other cases, actual plant test data are required to obtain more accurate simulations. The entire plant is shown in a single graphic screen so the user can see all the relevant information he might want, and soft-keys are provided for the user to make on- line parameter changes and observe the effects on storage elements, equipment feed rates and the final product size distributions. The model also reports equipment utilization in percentage, power consumption, and other related operating information, and soon, will be able to report estimated capital and operating costs.

Jan 1, 1999

By E. García-Ramos, P. Flores-Sánchez, E. G. Palacios, B. Zeifert, A. Romero-Serrano, M. Hallen-López

Chromium containing slags from stainless steelmaking may eventually be leached by acidic environments, therefore they should be treated before being stockpiled or land filled. In this work, synthetic slags were prepared and the effect of CaO/SiO2, Cr2O3, MgO and Al2O3 contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that CaCr2O4 and CaCrO4 are present in slags prepared with neither MgO nor Al2O3. The Al2O3-based slags mainly produced Ca2Al2SiO7 and the Cr(VI)-containing oxide complex Ca4Al6CrO16, whilst MgO-based slags produced MgCr2O4 as main mineralogical species. Additionally, Eh-pH diagrams for the Ca-Cr-H2O and Mg-Cr-H2O systems at 25 °C were constructed. The lowest Cr concentration levels in the leaching liquors corresponded to MgO-based slags owing to the stable binding of Cr in spinel with MgO. It was also observed in the Al2O3-based slags that increasing the slag basicity from 1 to 2 the leachability of the slags are notably increased.

Jan 1, 2008

By Pekka Hanniala

The falling real price level of copper metal and changes in the treatment and refining charges has been characteristic to the copper industry during the last few decades. Outokumpu's continuous development of the Flash Smelting Technology and increased productivity of the smelters based on these improvements may be one of the basic reasons that have influenced to these trends. From the early beginning of the Flash Smelting Technology, it has been characterized by low operation costs and low emissions, and the vision has been to develop the technology towards Direct Blister Flash Smelting. In Direct Blister Flash Smelting, both smelting and converting are carried out in one furnace making it possible to reduce the number of unit operation steps and thus lower both operation and investment costs. The merger of large copper production companies taken place during the last few years is a sign of a new age in copper production business. Now, the aim is to increase the productivity of copper production not just by utilizing the economy of scale but also by increasing integration and optimization of the whole production chain from mine to refinery. This also means increasing win- win based cooperation between companies. A Production Network concept based on the Flash Converting process enables existing smelters to decrease the operating costs and expand the smelting capacity with minimum investment and at the same time to decrease the emissions of the smelters. The new structure in ownership and partnership between copper production companies makes it easier to adopt the Production Network concept to both new and existing plants, where there exists a lot of built-in capacity. The paper presents Outokumpu's prediction on how the new options for the smelters will contribute to further changes in the structure of copper production. These visions are illustrated by giving examples on how the combination of matte production, Flash Converting, and Direct-to-Blister Flash Smelting could be adapted in existing and new smelters.

Jan 1, 2002

By David K. Melgaard

Electroslag Remelting (ESR) is a complex process used to produce high quality specialty alloy materials. The quality can be directly correlated to variances in melt rate and immersion depth. Conventional ESR furnaces control these quantities using two independent control loops using proportional changes in current for melt rate and driving the electrode up and down to match a voltage set point for immersion depth. However it is well known that the control loops are highly coupled, i.e. changing the current to account for melt rate deviations changes the voltage depth relationship and vice verse. In addition the noise in measurements of the ESR process can be considerable, forcing conventional controllers to use highly damped responses. A new model-based controller has been developed to embody the coupling and improve responsiveness by using estimates from a reduced-order linear ESR model and the typical process measurements to control melt rate and immersion depth simultaneously. Kalman filtering is used to optimally combine the model estimates of eight process states and the measurements of voltage, current, position and mass to estimate the instantaneous melt rate and immersion depth. Several ESR melts under steady state and transient conditions were conducted to evaluate the performance of the new controller. This paper will discuss the design of the new ESR model and controller and will present experimental results demonstrating its much improved control and responsiveness. While this controller was developed for the ESR process, the effectiveness of model-based control in managing such a complex process with relatively simple equations suggests the approach could be employed for many other processes as well.

Jan 1, 2006

By Abhishek Lahiri

Titanium dioxide is extracted from titaniferous ores by chloride and sulfate processes. These two processes produce wastes in the forms of iron chloride, iron sulfate and rare earth oxides gangue, each of which has to go through a further treatment before it can be disposed safely, which may be expensive. The shortage of high-grade ores is also making the two conventional processes less efficient. In view of the above mentioned problems, an alternate beneficiation process of roasting titaniferous ores with soda ash is discussed. The advantage of this process is that, there is no production of wastes. The impurities present in the ore can be selectively separated after the roasting process. The roasting of titaniferous ores with soda ash was carried out between temperatures of 873K and1173K for several hours. The roasting process resulted in the formation of complex alkali compounds and various sodium titanate compounds, depending on the Na2CO3to ore ratio. The phases formed after roasting were characterized using the X-ray powder diffraction (XRD), X-ray florescence (XRF) and scanning electron microscopy (SEM) techniques. The phase equilibria in the Na-Ti-O system are evaluated and compared with the phases obtained after the roasting process. The effects of temperature and the proportion of sodium carbonate on titaniferous ores are also discussed. From the experimental data, the overall reaction kinetics and phases formed were analyzed to ascertain the mechanism of overall reaction and the rate-limiting steps.

Jan 1, 2006

By Abhoy Mukherjee

The Luanshya Smelter is a traditional Reverberatory Smelter which once worked with up to three coal-fired reverbs, and now operates one Reverb and one hot Peirce- Smith Converter, projected to produce approximately 42.000 tons per year of copper anodes. The aim of this study is to select a smelting technology which best fits the upgrading of the Smelter, such that low capital and operating costs are achieved for the projected design production capacity of 60.000 tpy, limited by the available supplies of concentrates. An equally important requisite is the compliance of present and future environmental regulations, which determines the need to install and Acid Plant to treat the smelter primary gases. In the process selection study, the following technologies were analyzed, at a Conceptual Engineering level: the Oxy-fuel Burner Reverb, the Teniente Converter, the CONTOP Cyclone Smelting Reactor, and further, the Ausmelt Furnace, the engineering of which was provided by the proprietary firm. The engineering of the other processes was developed by INDEC, which also integrated the comparative analysis of the four options. The analysis of a comprehensive set of technical factors, including integrated smelter metallurgical models, together with the evaluations of economical features, led to the selection of the CONTOP Smelting Technology for the modernization of the Luanshya Smelter.

Jan 1, 1999

By J. Sjöblom

New copper and nickel processes, flash converting and DON, direct high-grade nickel matte smelting, have been developed in order to replace the conventional and not so environmentally friendly PS-converting process. With a laboratory scale laminar-flow furnace the combustion reactions of sulfidic feed particles can be investigated under simulated flash smelting conditions. In the present study, finely ground and screened feed fractions of a copper matte and a nickel matte were flash oxidized in a laminar-flow furnace. The experiments were carried out using 20, 21 vol% and 75 vol% O2 in nitrogen, at temperatures 1100 and 1300 °C and reaction zone length of 7.5-16 cm. The samples were quenched in a water film after a specified reaction time. The matte particle reactions were stopped after short residence time intervals in order to obtain a better understanding of the reaction mechanisms. Chemical analysis was used to determine oxidation degree, and optical and scanning electron microscope combined with energy dispersive analysis was used for characterization of the reacted particles. On the basis of the experimental results the reactivity of the mattes is discussed and possible reaction and dust formation mechanisms are considered.

Jan 1, 1999

By J. M. Tourre

1995 have seen a continuation of a positive trend in the Rare Earth industry The availability of a greater diversity of Raw Material has brought additional flexibility to the Producers permitting better economics China remains the major raw material source; Chinese concentrate producers have increased capacity in 1995 (Baotou, Sichuan, etc) China's role in the Rare Earth industry will continue to evolve; the acquisition of a majority equity position by San Huan/CNNC will have a significant impact on both the Rare Earth and Magnet markets Chinese producers are increasing the quality of their products and realize their true values Chinese market, itself, is also changing as the internal needs for separated rare earth's grow Already already producer of Lamps, Loudspeakers, Magnets, and TV tubes, China is in an unique position where the potential of its internal market might be more promising than the prospects outside China 1995 has also seen the application market become more diverse and complex. There are new applications growing at a very strong pace (such as battery alloy), applications that are now penetrating their target markets with significantly increased growth rates (such as bonded NdFeB), and some applications that became more complex requiring much more sophisticated products (such as catalysis). Rare Earth producers have to spend significant ressources in order to monitor the market trends in order to predict the demand and then adjust their raw material mix. Even though there is a greater diversity of raw material available, there is still some Rare Earth elements that are in excess, while other are just in balance. As a consequence rare earth producers invest heavily in R&D in order to develop new applications for these excess elements.

Jan 1, 1997

By Maura Malone, Neil Gao, Daniel Liu

"Corrosion is the primary failure mode for aluminum cathode sheets used in Teck's Trail Operations electrolytic zinc plant. It was observed that the corrosion performance of Al cathodes from different suppliers varied considerably. This suggests that the material properties of Al cathodes have a strong influence on corrosion resistance. In the current study, various types of Al alloys, including 1050, 1060, 1070, HIS and 1090, were characterized through chemical analysis, corrosion testing, mechanical testing and metallography. The results are discussed with a focus on the effects of impurity elements and second phase particles on corrosion resistance. The findings were used to improve the Al cathode sheet specification and to develop a standardized screening procedure which details qualification steps for comprehensive evaluation prior to a plant trial.IntroductionAluminum (Al) cathode replacement is a major operating expense at Teck's Trail Operations zinc electrolytic plant. Currently, approximately 0.5% of daily stripped Al cathodes are removed from service because of failures caused mainly by corrosion. Edge corrosion and acid (solution) line corrosion are the most severe types of corrosion, resulting in more than 50% of cathode failures.Corrosion of Al cathodes has been intensively investigated for over two decades and the origins and mechanisms of Al cathode corrosion are well understood [1-4]. Halide anions contained in the electrolyte are the primary culprits for the corrosion and sticking problems of Al cathodes. Both fluoride (F') and chloride (Cl"") result in localized passivity breakdown on the surface of the Al cathode, causing pitting corrosion. Bouarzaiga investigated the corrosion of Al cathode samples partially immersed in electrolyte and found that the formation of Ch at the electrolyte/air interface was the primary contributor to solution line corrosion [2]. Because of the significant impact of F"" and Cl"" on Al cathode corrosion, it is imperative to maintain these concentrations as low as possible in the electrolyte."

Jan 1, 2012

By Pranav Deshpande

The wear behavior of metal matrix composites differs from that of the monolithic metallic counterparts because composite materials have multiple constituents in their structures and these constituents wear at different rates. It was observed that under low wear stresses, abrasive wear prevailed. As the wear stress increases, pullout of reinforcement occurs and both abrasive wear and wear due to pullout contribute to the overall composite wear. A model of wear taking into account both types of wear has been developed. A critical pullout wear stress was suggested for each composite. Below the critical wear stress, no pullout of reinforcement occurs. It turns out that the critical wear stress simply equals to the ratio of the interfacial strength between the matrix and the reinforcement to the friction coefficient between the reinforcement and the wear counter surface. The critical wear stress is independent of the particle size of the reinforcement. From data on wear of 53% WC composites, the equation of wear for 32% WC composites was obtained. Experimental results agreed well with the predicted wear rate of this composites. This provides an excellent verification of the wear model developed by Lin and Deshpande. Wear data from Modi et al. in the literature were also perfectly fitted with the model.

Jan 1, 2006

By M. Olper

Today, copper production from direct leaching of oxidized copper ores followed by solvent extraction-electrowinning (SX-EW) accounts for about 15% of the total primary world output. SX-EW is a well-accepted process with an operating cost in the range 16-20 cents/lb. copper for small and medium size plants, depending on the plant size and local conditions. However, this technology presents some drawbacks that affect the operating cost and cause environmental concerns. ENGITEC and Paques Bio Systems have developed a new process that avoids the solvent extraction step and operates the copper electrowinning step at a lower cell voltage because of the depassivation of the anodic reaction. The consequence of this new concept is that the direct operating cost is in the range 10-12 cents/lb. copper. This new process is composed of the following steps: ? Selective precipitation of copper from leach solutions by biogenic H2S, yielding CuS and regenerating acid ? Leaching of the CuS with a ferric fluoborate solution to dissolve copper and produce elemental sulphur that is recycled back to the H2S biogeneration step ? Electrowinning of copper fluoborate solution in a diaphragm cell with the ECUPREX® Process, producing copper cathodes and regenerating the ferric fluoborate solution to be recycled back to the leaching step ? Biogeneration of H2S from the elemental: sulphur generated during the leaching step, with the nutrient source for the anaerobic bacteria selected form a wide range of organic substances and/or some industrial by-products containing carbon and hydrogen This paper describes all process steps with particular reference to the biological H2S generation technology. Also discussed' is the capability of the ECUPREX® Process to treat copper sulphide concentrates and copper matte.

Jan 1, 1999

By M. J. Perpich

Electrochemical and chemical leaching tests were carried out on chalcocite, covellite and chalcopyrite in acidified iron sulfate solutions sparged with a mixture of O2 - SO2. The gas mixture catalyzed the ferrous to ferric oxidation reaction in situ and, therefore, increased the redox potential and oxidizing strength of the solution. Anodic polarization curves in dilute sulfuric acid on copper sulfide electrodes showed that chalcopyrite passivates and dissolves at current densities orders of magnitude less than chalcocite and covellite. The addition of a depassivating agent (Ag+) increased the passive current density of chalcopyrite and caused breakdown near 0.625 V (SCE). The depassivating effect was also observed during the leaching of chalcopyrite particulate samples as small amounts of Ag+ added to acidified iron sulfate solutions in the presence of O2 - SO2 mixtures greatly increased the leaching rate and the total amount of Cu oxidized (> 90%). Passivation was prevented in the absence of Ag+ by decreasing the initial oxidizing power of the solution and by pretreating the sample in a reductive leach. Both of these methods resulted in transformation of the chalcopyrite surface from its characteristic greenish-gold into deep black. Increased concentrations of Fe+++ due to 02 - S02 sparging were then able to oxidize the transformation product.

Jan 1, 1999

By Peng Bing

Stainless steelmaking dust is classified as a hazardous waste due to higher than acceptable heavy metal leachabilities such as zinc, lead, cadmium and chromium. In addition to being an environmental hazard, the flue dust is also an economical concern to stainless steelmakers as it contains large amounts of valuable alloying elements, especially for iron, chromium and nickel. A new technology of direct recycling of stainless steelmaking dust has been developed to recover the metals from the dust. But it was found that zinc was accumulated in the dust collection system in practical run of direct recycling. This study focuses on the effect of the operating parameters such as temperature, dust feed rate and the ratio of CO to dust on the reduction of zinc oxides present in the dust. The mathematical model for the reduction process was setup based on the experimental research. According to the mathematical model, the temperature has obvious effect on the reduction of zinc. It is benefit to the process of zinc reduction to increase the temperature. But the temperature will not be the main factor for the reduction process after 1228C. It will promote zinc reduction to decrease the dust feed rate and control the ratio of dust to CO. It was also found from the experiments that ZnFe2O4 in the dust could be decomposed at high temperature. Decomposing ZnFe2O4 in the dust increases the recovery of zinc from the dust distinctly.

Jan 1, 2006

By Chuan-fu Zhang

The fibrous precursor can be obtained by coordination precipitation process, using oxalate, cobalt chloride and ammonia. XRD pattern of precursor precipitated at pH=9.0 is different from that of ß-CoC2O4?2H2O precipitated at pH=1.0 which indicates that the precursor powders are one type of cobalt complex. According to the results of element analysis and IR spectra, it can be inferred that the composition of the precursor is [Co(NH3)x]C2O4?H2O(x=1.2?..6) formed by the coordination reaction at pH=9.00 in the Co(II)-C2O42--NH3-NH4+-H2O system. It?s found that the fibrous cobalt powders greatly inherited the morphologies of the precursors. Many factors could affect the formation of the fibrous cobalt precursor powders, such as the initial Co2+concentration, pH value and so on. The SEM images show how they influence the morphologies of the precursor powders. By adding proper surfactant, the dispersion of the precursor powders would be improved. At last, the final product-fibrous cobalt powders which are about 0.3~0.5min size and 40~60 in aspect ratio were produced by thermal decomposition of fibrous cobalt complex at 400~500°C in the weak reducing atmosphere.

Jan 1, 2006

By O. Tiitu

Drying is a unit process that has numerous applications in metallurgical process industry. Kumera Technology Center is a worldwide equipment and process supplier, who has expertise on both direct and indirect drying. In a conventional direct heated dryer, the required energy is obtained from combustion of fossil fuels emitting a considerable amount of off-gases. However, thermal energy can be already available in some metallurgical plants such as modem copper smelters where steam is produced by waste heat boilers of flash smelting furnaces. The total volume of off-gases, and especially the amount of harmful gases, released into atmosphere can be remarkably reduced when using steam as an indirect energy source for drying. Kumera Technology Center has developed a new type of steam dryer for drying of, for example, abrasive copper concentrate with silica sand. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the existing steam dryers and the rotating drum dryers. In the design, special attention has been paid to overcoming the reported problems of excessive wear and clogging of steam tubes and to reducing the required maintenance operations. The Kumera Steam Dryer, having a patented flexible steam tube arrangement inside the rotating shell, has a high effective heating area - drum volume ratio without leading to problems with build-up and clogging. It can also be easily scaled up so that a single dryer can dry all of the feed for a large flash furnace. In this paper, we will present the operational and maintenance experiences from two years operation of the first full-scale Kumera Steam Dryer at Norddeutsche Affinerie Aktiengesellschaft in Hamburg, Germany. We will also provide an overview of the future developments with respect to construction and scale up as a response to market demands.

Jan 1, 2002