Search Documents

By B. Mishra

Several reactive metal purification processes using molten salts generate effluent from which significant quantities of metal can be recovered prior to discardinglrecycling the salt. A Salt-scrub [SS] process has been applied where the reactive metals are recovered as a metal-gallium alloy by calciothermic reduction of the metal compounds. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. Measurement of metal recovery has been studied for cerium, silver, tin and lead. The process has been optimized for variables such as the metal quantity per kg of effluent salt, amount of excess calcium over stoichiometry, stirring rate and time and holding time at reduction temperature. Over ninety-seven percent metal recovery has been obtained under optimized conditions. The development of an alloy for efficient Salt Scrub processing reduces a major contaminated waste disposal problem as well as recovering the valuable reactive metal. Surrogate metals have been used in this work to study the behavior of plutonium.

Jan 1, 1994

By B. Madelin

Over the last ten years, Minemet Recherche and Metaleurop have used an approach in order to investigate and improve the operation of its Smelting furnace and its lead blast furnaces. This approach gives importance- to three complementary means of investigation : - Probing campains in the industrial furnace (temperature and gas analysis profiles), - Chemical and physical modeling (coke combustion, sinter reduction modes, flows patterns, ?.) , - Staged mass and heat balances or kinetic model. This allows to define the limits of operation of each blast furnace and to predict the influence of operating parameters on the furnace performances. For the zinc Imperial smelting furnace, the probing results show the existence- of both an Isothermal reserve zone at 1015ºc and a chemical equilibrium between ZnO and gas which makes possible the use of a practical model for heat and material balances. In particular, very good prediction on the influences of operating parameters can be made. On the contrary, for lead blast furnaces, the probing results show that the thermal and chemical equilibria are not reached. Consequently, classical models for staged heat and mass balances are not sufficient. The use of the other means allows then to characterize the specific influences of operating parameters on the thermal instabilities of these furnaces and their allowed limits.

Jan 1, 1990

"In this paper, a mobile heat treatment furnace from Akkermans Gloeitechniek, a Dutch company, was simulated with Computational Fluid Dynamics (CFD). The furnace is cylindrical with four oil burners, and large metal products such as dredging pumps and impellers can be flexibly heat treated to obtain required microstructure and mechanical properties through stress relief, annealing, hardening and tempering. The furnaces are exposed to the open air, and thus the heat loss becomes significant and varies from day to day and from season to season. Since the temperature of the metal products to be heat treated can only be measured on the surface, the temperature evolution inside the metal could not be tracked in practice. CFD simulation provides a useful tool to predict the temperature evolution within the metal pieces and within the combustion space of the furnace. Energy distribution and heat loss can be subsequently estimated. An overall energy balance through temperature measurement indicted relatively low energy efficiency. Especially during the soaking period, the high energy supplied is barely used to compensate the heat loss of the furnace to maintain a constant temperature of the metal piece. The current CFD modeling aims to give advice on how to modify the design and optimize the operation to reach higher energy efficiency and low heat loss. The CFD model consists of turbulent combustion model, radiation model in participating media, and conjugate heat transfer between the combustion space and solid metal. Temperature measurement was carried out to provide thermal boundary conditions and overall energy balance of the operation. After the model validation with temperature measurement within the combustion space and metal surfaces, furnace optimization will be conducted.IntroductionHeat treatment is a common practice in metal production and manufacturing industries. Through heat treatment at certain temperatures with special patterns, unique mechanical properties of the metals and the metallic products could be obtained. ""Akkermans Gloeitechniek"" is a company situated in K.inderdijk, at location of LHC-Holland (www.ihccaland.com), the Netherlands. Heat treatment of metals is its core business. Various type of heat treatment are applied, such as stress relieving, soft annealing and hardening (quenching), tempering, transformation and precipitation. At the company 6 furnaces are in operation and the 7th is being built"

Jan 1, 2004

"Many industrial processes involve materials that are subject to temperature change and thermal stress. Examples range from the casting of large metallic products to the cooling and reliability of small electronic components. Thermally induced stress is a major concern as it can lead to material damage and product failure. Material properties, thermal and mechanical, and process conditions such as the size and location of a feeder in metals casting, or the power dissipation in a computer chip, will govern the magnitude of these stresses. Temperature may also be influenced by fluid flow, for example, the airflow over a computer chip in a laptop will govern the rate of heat extraction, hence the temperature gradients in the chip and the evolving thermal stresses.This paper provides details on the governing equations for heat transfer (temperature) and solid mechanics (stress), their degree of coupling, and the numerical techniques used to solve them. Three examples are discussed to illustrate the use thermomechanical modelling. These also provide an insight into the degree of coupling required between the equations. The first example, involves thermal cycling of electronic components where a prescribed temperature field is applied. As temperature is known, this example only requires the solution of the stress equation. The second example also involves the modelling of an electronic component where the temperature field is also calculated. In both of these examples, the stress calculation is dependent on the temperature field, but the temperature calculation is not dependent of the solution of the stress equation (one-way coupling). The final example provides details on modelling the metals casting process. Both the temperature and stress equations are solved but, unlike the previous two examples, in this case the temperature field is dependent on the results from the stress calculation (two-way coupling)."

Jan 1, 2001

By M. Shevchenko

Integrated experimental and modelling research program on the phase equilibria and development of thermodynamic databases of the lead and copper metallurgical gas/ slag-matte-metal-solids systems (PbO-“Cu2O”-FeO-Fe2O3- ZnO-CaO-SiO2) is being undertaken to support improvements in the pyrometallurgical smelting and recycling processes. This is the first systematic investigation of phase equilibria of slag systems in equilibrium with Pb metal, providing information for systems in which copper coexists in slag with lead or zinc as major components. The experimental studies involve high-temperature equilibration of synthetic samples, rapid quenching, and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). FactSage-based thermodynamic database development is integrated with experimental research. Initial thermodynamic assessments are used to identify priority compositions and conditions for experiments, which are planned to provide specific data to assist thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved. Continuous database improvement and extension to include new elements are targeted. Example of industrial application is given.

By B. J. Elliot

The Outokumpu Oy flash smelting furnace was designed for a capacity of 69,5 mtph of concentrate. The history of developments on the flash furnace, from the original operating capacity of 55 mtph to a proven capacity of 115 mtph of concentrate, is summarised. The new feature of operation at BCL Limited is ?the use of screened lump coal reduction in the settler region of the furnace. This paper considers the effects of settler bath reduction on the furnace smelting capacity, the condition of the furnace ?lining and bath, and ,the slag losses generated from the flash furnace and ultimately to discard. By using the settler bath reduction technique the capacity of the furnace for smelting new concentrate has been increased by 15% and hearth accretion has been eliminated by direct reduction with coal, which has also allowed the generation of a substantial protective lining on the furnace walls and roofs. As a result of improved slag losses from lump coal charging the metal recoveries on the flash furnace have increased from 70% to 87% for nickel, 68% to 82% for copper, and 28% to 45% for cobalt.

Jan 1, 1983

By Katja Reinharter

Arsenic can be found in different sulfidic copper concentrates and residues, which for several years have commonly been used in copper metallurgy, as the “arsenic-free” resources are getting rare. Due to the high toxicity the removal of arsenic in the copper smelting process is a very important topic. The typical chemical slag and sulfur attack on the refractory material is getting enhanced by the presence of arsenic. This work deals with post-mortem investigations of a magnesia-chromite brick and castable used in copper smelting furnaces showing an additional and increased chemical attack by arsenic. The knowledge on the wear behaviour is not only based on a detailed chemical and mineralogical characterization, but also on thermochemical FactSageTM calculations, which are carried out on provided post-mortem samples. Post-mortem investigations on used refractory materials represent an important prerequisite for the product development, as well as for special engineered lining concepts to support our customers.

By Allan MacRae

Freeport-McMoRan Inc. operates an ISASMELTTM furnace for the smelting of copper concentrate at the Miami Smelter in Claypool, Arizona. In May 2017, the furnace was restarted after incorporating newly designed copper cooling elements from just above the tap hole to the underside of the roof. The objective of the improved cooling design was to extend campaign life by eliminating existing failure mechanisms with the wall refractory. In addition to upgraded bathline coolers and complete coverage of the gas offtake transition, or ‘kettle’, with plate coolers, a novel arrangement of coolers was installed in the remaining freeboard area. The shell required significant cutting and re-stiffening, as well as extensive modification of the cooling water piping. Based on performance observed to date, it is expected that smelter throughput will be increased due to extended ISASMELTTM refractory campaign life.

By L. J. Friedman

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric ?acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design _to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators, The current? design offers improved' impurity scrubbing along with increased reliability. in addition, a number of alternate gas cleaning systems have been offered Chemetica LAB System; Monsanto DuPont D:Jna-Wave Syatem1 Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems. _

Jan 1, 1992

By Vinicius Alves Gomes, Jean Igor Margem, Thallis Cordeiro, Frederico Muylaert Margem, Roberto Faria Jr., Sergio Neves Monteiro, Marina Rangel Margem

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and neutral with respect to CO2 emission. In particular, the fiber extracted from the malva plant stem is nowadays recognized as one of the strongest lignocellulosic fibers. However, the thermal properties of the malva fibers have yet not been fully investigated. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity of a pressed malva fibers sample. The results revealed that these fibers showed a superior thermal insulation capacity.

Jan 1, 2015

By Versiane A. Leão

The adsorption of oleic acid and amine, by Expanded Hydrophobized Vermiculite (EHV) was studied. In appropriate conditions EHV is a good adsorbent for these flotation re-agents and the best results are obtained at situations where the chemicals are at non-dissociated form. The adsorbent shows good chemical stability and may been used in many adsorption-desorption cycles.

Jan 1, 1996

By Thomas P. Battle

Modern-day direct reduction of iron first developed as a small-scale, low capital and operating cost alternative to the blast furnace. Since commercialization of continuous DR technology in the late 1960s, the market for the products of direct reduction has grown to more than 74 million tonnes in 2012. The initial advantages of DR plants over BF facilities have grown over the years, for several reasons, including the increased size of DR modules, lower energy and emissions (particularly CO2), along with the flexibility to use a number of different reductants. The development of DR technology over the past forty years will be emphasized in this presentation, including recent developments that allow for even more direct sustainability comparisons with the iron blast furnace – and even combine the two technologies for improved synergies. Also briefly discussed will be the possibilities of using direct reduction for non-ferrous ores.

Jan 1, 2014

By Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"In this paper, we describe the current status and research progress on the utilization of typical industrial solid wastes in China. We propose a creative method called “eco-utilizing wastes” with an aim of both integration and increment but without second-time waste and pollution, in terms of the characteristics of typical industrial solid wastes, such as titanium-bearing blast furnace slag, high-silicon iron tailing and boron-enriched slag as well as oil shale.Situation of Typical Industrial Solid Wastes in ChinaThough mineral resources in China are abundant, most of these are low grade ores. Moreover, the distribution of mineral resources is asymmetric, which causes the increase of cost and decrease of the economic benefit. Over-exploitation of mineral resources results in a large number of solid wastes. The accumulation of solid wastes not only means the waste of valuable resources, but also causes environment deterioration. There exist some problems in the current practice of the disposal of industrial solid waste, such as only emphasizing the final results and causing new pollution and waste [1]. So the research and development of a high value-added method has a high practical relevance to our nation. Based on the present status and research progress of industrial solid wastes in China, a creative new idea and method for eco-utilization of solid wastes is proposed in this paper."

Jan 1, 2012

By Augusto Viana Leandro Teixeira

Rare Earth Elements (REE) are fundamental for modern life products and green technologies. Supply constraints and the price peak of 2011 boosted intensive research for alternatives for processing and separation. Complex monazite- type, rare earth ores usually contain high acid consumption impurities, such as iron and aluminum, and radioactive thorium in their composition. These impurities are not removed by conventional concentration processes due to fine, micro-level association between the REE carrying minerals and the gangue minerals. This work presents a selective process route for REE extraction from iron-rich, monazite ores. The process involves sulfation by addition of concentrated sulfuric acid and pyrohydrolysis at temperatures of approximately 700–750 °C. Experimental results show REE extraction higher than 70% and low iron (below 5%) and thorium extraction (below 10%). A method based on thermogravimetric analyses was shown to be adequate to predict the behavior of a given ore sample in the sulfationselective pyrolysis-leaching process.

By Satu Jyrkönen

A single-particle laminar-flow technique was used to study oxidation of four synthetic nickel mattes, which were screened into three size fractions, Experimental conditions were: reaction gas from N2 - 21 to 75 vol-% O2; gas preheating temperatures ranging from 500 to I 100'C. The four mattes were synthesized so that Ni/Cu ratios of I and 10 were obtained with high and low iron contents. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect their morphology, internal composition and structure. The best sulfur removal from the synthetic nickel mattes was achieved under the most oxidizing conditions with the finest size fraction. The matte with Ni/Cu = 1 and high iron content was found to be most reactive. The least reactive matte was with Ni/Cu = 10 and low iron content; the coarse fraction particles did not react at all under the conditions studied.

Jan 1, 1996

By S. N. Monteiro, C. M. F. Vieira, M. M. Ribeiro

"This work has as its objective to evaluate the effect of incorporation of the powder waste retained in the eletrostatic precipitator of the sintering stage from an integrated steel making plant on the physical and mechanical properties of a red ceramic. Formulations were prepared with incorporation of the waste in amounts up to 20 wt.% into a kaolinitic clay. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 750, 900 and 1050°C. The evaluated physical and mechanical properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste has a potential to be used into red ceramics. The incorporation of the waste enhanced the properties of the ceramic, decreasing the water absorption and increasing the mechanical strength at all investigated temperatures.IntroductionThe sintering stage of an integrated steel-making plant is dedicated to the agglomeration of a mixture of iron ore, coke or coal, fluxes and water [1]. It is a common practice in this stage to use of solid wastes with great amounts of iron in the form of sludge and powder. One of the atmospheric pollutants generated during the sintering process is the particulate material, which is normally retained in an equipment denote as electrostatic precipitator. This equipment retains very small particulates, present in the gaseous emissions by application of an electrical potential difference in between the plates that the fluid is forced to go through. [2]."

Jan 1, 2011

By Fathi Habashi

While it is commonly known that the precious metals and to some extent copper occur in the native state, it is less known that mercury, iron, nickel, and cobalt do occur also in the native state; the last three (Fe, Ni, and Co) usually occur together in form of an alloy. The particle size varies greatly from less than 10 microns (gold and mercury) to about 400 tons boulders (copper).

Jan 1, 1993

By Gerardo Fuentes

The stoichiometry and kinetics of the hydrothermal reaction of enargite in copper sulphate solutions was investigated in the range 140–300 °C, and particle size under 15 and 50 μm. The stoichiometric experiment was performed at 300 °C, using one gram of sample (96% enargite, 4% tennantite) and 100 mL of copper sulphate solution (10 gpl) at 1.2 pH. Enargite reacted completely after 80 min. A solid product was obtained and characterized by XRD. The main product was chalcocite (M) and some traces of djurleite and chalcocite (Q). Tennantite did not react under these conditions. The kinetic experiments were conducted at 140 °C, 190 °C, 250 °C and 300 °C. From fitted data and Arrhenius equation the calculated activation energy (Ea) was 51 kJ/mol. According to the hydrothermal transformations studied, the reactivity of different phases found in the copper concentrates was bornite > chalcopyrite > covellite > sphalerite > pyrite > enargite > tennantite.

By Artur R. P. Junior Sergio, Pedro A. Netto, N. Monteiro, Foluke S. de Assis, Frederico M. Margem

Synthetic fibers are being replaced gradually by natural materials such as lignocellulosic fibers. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as environmental and economic. So there is a growing international interest in the use of those fibers. The banana fiber presents significant properties to be studied, but until now few thermal properties on banana fiber as reinforcement of polyester matrix were performed. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity for polyester composites reinforced with banana fibers. In the polyester matrix will be added up to 30% in volume of continuous and aligned banana fibers. These values show that the incorporation of banana fibers in the polyester matrix changes its thermal properties.

Jan 1, 2015

By Rajashekhar Marthi

Lithium is a key component for future electric vehicle batteries and energy storage. The future availability of lithium to meet the growing demands remains in question. Around 60% of lithium resources exist in the form of continental brines. Traditional methods to recover lithium from brines use solar concentration with precipitation and have found limitations in lithium extraction due to interference of Mg in high Mg/Li brines. Thus, there is a need for highly selective adsorbents. Recently, spinel structured delithiated lithium manganese oxides have demonstrated promising results. However, due to the small particle sizes, it is economically difficult to recover the adsorbents and thereby limits industrial applications. In our work, LiMn2O4 ion sieve was synthesized and immobilized on diatomaceous earth. Fundamental adsorption studies were carried out in lithium buffer solutions to understand the nature of adsorption and kinetics. The adsorbents were also tested for recycle stability, as well as recovery of lithium from Great Salt Lake water samples.