Search Documents

By T. Innmi

The potential of the nickel matte anode was measured during the matte electrolysis in the commercial cell. The slime layer consists of elemental sulfur and was found to greatly influence the potential of anode. The measurements of porosity and permeability of the slime suggest that the voltage drop of the slime layer dominates the potential. Furthermore, the diffusion of the electrolyte through the slime layer is also one of the factors to determine the potential. In addition, the copper content of the nickel matte anode was found to affect the change in the anode potential during the electrolysis. The role of copper on the anodic dissolution of nickel matte is discussed in this work.

Jan 1, 1988

By A. A. Bustos

A model was developed to simulate the blow-by-blow operation of the converting process. From the weights, compositions and temperatures of all converter feeds the model calculates the composition and tonnage of both converter matte and slag as well as bath temperature at the end of each blow. The development of the model and its application to the converter aisle operation are described. There is good agreement between model predictions and observed results. At the present time the model is being used to investigate different converting schemes and their effect on pay metal recoveries, slag chemistry and temperature of the bath. Future work involves the use of the simulation model as a process control tool for the converting operation.

Jan 1, 1988

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By Qingchun Yu, Baoqiang Xu, Yongnian Dai, Bin Yang, Fulong Zhu

"In this paper, the mechanism of the carbothermic reduction-chlorination process to extract aluminum from alumina in vacuum was investigated. The carbon monoxide (CO) content of the gas, phases of the reduction slag, surface morphology of the reduction slag and the product aluminum were measured by means of gas chromatography (GC), XRD, and SEM. The experimental results indicated that the content of CO in the gas decreased, but Al4C3 increased with time at 1773K during the carbothermic reduction process of alumina. AlCl(g) and graphite (C) were produced by the reaction between Al4C3 and AlCh(g) at 1773K, and then aluminum beads generated after the decomposition of AlCl(g). It implied the mechanism of alumina carbothermic reduction-chlorination process in vacuum involves three steps as follows: the carbothermic reduction of A}z03 to produce Al4C3, the chlorination of Al4C3 by AlCh(g) to produce AlCl(g), and the decomposition of AlCl(g) to produce Al(l).IntroductionAluminum is the basic raw material for many industries [1], and it is used extensively because of various excellent properties such as light weight, good malleability, high strength, excellent thermal conduction, high corrosion resistance and so on [2]. Industrial production of aluminum currently includes refining alumina and electrolytic aluminum processes. However, its development has been effected by some factors such as high energy consumption and heavy environmental burdens [3]. In the past several decades, there had been numerous attempts to produce aluminum by new methods. Extracting aluminum from alumina or bauxite directly by carbothermic reduction-chlorination process had been studied [ 4-6]. Although the alumina carbothermic reduction process [7~9] had been studied, the mechanism of the carbothermic reduction-chlorination process had not been systematically elucidated.In order to investigate the mechanism of the carbothermic reduction-chlorination process in vacuum, GC, XRD and SEM techniques will be used to determine the CO content and to characterize the surface morphology and composition of the slags at various temperatures."

Jan 1, 2011

By J. R. Kiji

The Cerro Matoso S.A. mine and smelter, in the Cordoba lowlands of northwestern Colombia, consist of a dedicated laterite nickel mine, ore blending, drying and an RKEF process to produce high-quality ferronickel. At a project investment of $400M, first production of ferronickel was in September 1982, and in its inaugural year CMSA produced 6,150 tons of contained Ni from a mined ore grade of 3.2% Ni. Initial operational difficulties resulted in a number of furnace run-outs, which impacted ramp up to design ore throughput of 128 dry t/h Since then CMSA has steadily incorporated process improvements and initiatives to take the single line operation to an ore throughput of 175 dry t/h. A second 175 dry t/h line was added in 2001 (investment of US$ 300M) to consolidate CMSA as one of the world's lowest cost Ni producers with an installed annual production capacity of 50-55,000 tons Ni. The most recent addition is commissioning of Phase I of an ore-upgrading project to counteract the effect of declining ore grades. Keywords: Laterite, ferronickel, pyrometallurgy, smelter.

Jan 1, 2004

By J. W. Evans

Mathematical modeling has now become a standard technique in the development of new technology and the improvement of existing technology in the processing industries. Physical modeling has a longer history but a smaller following at present. The paper reviews some examples of the application of both types of modeling in non-ferrous metal extraction, particularly within the copper and aluminum industries. The objective is to show that well founded models can lead to results that have practical consequence in scaleup, design and operation.

Jan 1, 1993

By W. H. (Bill) Jay

The destruction of cyanide creates a significant impost on the financial returns of gold mines. These losses increase substantially when ores containing cyanide-soluble copper are treated. Failure to remove or destroy free or WAD cyanide before it is discharged into tailings dams has, on a number of occasions, led to significant fish, bird and animal deaths. Thus, the retention of cyanide within the leach circuit and the recovery or removal of stable metal cyanide complexes needs to become standard practice for all gold mining operations. Furthermore, reducing cyanide purchases will minimise the quantity of cyanide transported to the mine site thereby reducing the opportunity for spillage of this chemical. Many different physical and chemical methods have been investigated for the removal of cyanide from process solutions. All cyanide destruction methods create a financial impost on the economic viability of the gold mine. To reduce these costs, the recycle of cyanide and the economic recovery of the metals solubilised by cyanide is of prime importance. The alternative methods currently in use, or under consideration for the treatment of copper cyanide, entail high reagent costs, produce the recovered metal in a contaminated form and require the safe handling of hydrogen cyanide. These processes will be briefly discussed within this report Environmental and financial benefits are enhanced by recent laboratory and pilot plant studies conducted by Oretek Limited. The Oretek CPC process for the recovery of copper and the recycle of cyanide from copper cyanide-containing solutions does not require pH adjustment to the alkaline cyanide leach conditions. Copper ions are coordinated to a water-soluble and/or an organic soluble polychelating agent under alkaline conditions and the cyanide ions are displaced Membrane separation, or phase separation of the polychelated copper from the cyanide ions enables the cyanide ions to be recycled and the copper to be directly electrowon from the polychelating polymer. The polychelating polymer is then recycled. Ion exchange resins and solvent extraction systems which may be incorporated into the above process will also be discussed in detail.

Jan 1, 1998

By Joël P. T. Kapusta, Romeo U. Pagador, Noparut Wachgama, Chumnoom Khuankla

"Thai Copper Industries (TCI) is a custom copper smelter and refinery in Rayong, Thailand, with an annual capacity of 165,000 tons of cathodes. It employs the El Teniente Technology as the primary smelting reactor to produce white metal from copper concentrates. The white metal is further treated in Hoboken Siphon Converters to produce blister copper then refined in anode furnaces before being cast into anodes for electro-refining in the on-site tankhouse.Thai Copper Industries is the first copper smelter to install and successfully operate on a commercial scale with the Air Liquide Shrouded Injection (ALSI™) Technology in the Hokoben converters with sonic injection of oxygen enriched air and nitrogen for cooling of the injector tip areas. Following commissioning and the establishment of operating practices, the performance of the Hoboken converters with ALSI™ Technology produced outstanding results. The unique combination of an El Teniente and Hoboken siphon converters, both of which are bath smelting operations, offers very high blowing and oxygen efficiencies. As a consequence, reverts recycling was accelerated with minimal build up on the mouth, end-plates or even below the siphon that is typical in Hoboken converters.These outstanding results in the Hoboken Siphon Converters with ALSI™ Technology helped the TCI Plant reach a production of about 75% of its capacity within four months despite the fact that the TCI staff is quite young and its converter know-how and experience are not yet fully developed."

Jan 1, 2009

By Terence Makanyire, Animesh Jha

The dissolution and chemical properties of vanadium, zirconium, and niobium in rutile lattice are analyzed by comparing the octahedral site preference energies, with respect to Ti4+ ion in the solvent phase. The oxides are often present in rutile lattice and interfere in achieving the quality of pigment grade TiO2 due to favourable Gibbs energy for dissolution in the solvent rutile matrix. Binary mixtures of V2O5 { TiO2; Nb2O5 { TiO2 and ZrO2 { TiO2 with compositions of 80, 85, 90, 95 and 97 wt% TiO2 were made, pelletized and sintered at 1100 °C for 24 hours. The solidsolution mixtures were then cooled and leached in 2M NaOH for 3 hours at 60 °C. Phase and lattice parameter characterizations, and microstructural and compositional analyses were then carried out using X-ray diraction and SEM/EDX, respectively. The leachates were analysed by Atomic Absorption Spectroscopy (AAS), using which the solute dissolution model for oxides were investigated.

Jan 1, 2014

By S. Peng, Vaughan R. Voller

"Free boundary problems are a common occurrence in materials processing operations. An important example is the filling of material into molds. This paper looks at filling problems associated with polymer processing, in particular Resin Transfer Molding (RTM) and Compression Molding. A general, single governing equation is developed which on numerical solution provides predictions for the position of the polymer front in the mold during filling. Both fixed and deforming finite element solutions are developed. Application to polymer filling test problems reveal that the fixed and deforming grid scheme are accurate and compare closely with each other.IntroductionProblems arising from the analysis of material processing operations often involve the tracking of a moving boundary, on which a balance conditions needs to be met, or the locating of a free surface that defines the solution domain. Material processing examples of so called ""free and moving boundary problems"" include; the tracking of solidification/melting fronts[l], the tracking of the metal/gas interface during the filling of a mold[2] and location and shape of a skull (freeze line) in a melting furnace[3].Computational solution of free and moving boundary problems usually fit into one of two classes, viz.1. Fixed grid scheme: In which the spatial domain is covered by a fixed grid (mesh) of node points and the solution uses an auxiliary variable (e.g. a local liquid fraction) to track the moving boundary or locate the free surface.2. Deforming grid scheme: In which the grid in the spatial domain is continuously deformed (or adapted in a steady state problem) such that a specified set of grid points lie on the moving boundary or the free surface.Details on the basic underlying features in these two classes of solution can be found in the excellent monograph by Crank [4]."

Jan 1, 1994

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By S. P. Rivers

The stainless steel industry re1ies on nitric-hydrofluoric acid (HNO,/HF) pickling solutions to remove surface contaminants and maintain the corrosion resistance of the steel. More stringent environmental guide1ines are expected to be placed on the disposal of these solutions which could significantly increase processing costs. The U.S. Bureau of Mines has been conducting research to develop a process for recycling depleted pickling solutions, thus reducing the quantity of by product acids generated. Research has shown that F- can be liberated from the predominant iron fluoride species (FeF,') by using oxalic acid in an electrodialysis cell. Ion selective membranes allow dissolved metals in the depleted solution to be replaced with hydronium ions by metathesis, thereby regenerating the HF. The regenerated HN03/HF is then retained in the pick1ing solution. This paper reports on the research effort at the U.S. Bureau of Mines Rolla Research Center to apply electrodialytic recycling to HN03/HF pickling solutions.

Jan 1, 1993

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

By William R. Opie

Considerable effort by extractive metallurgical research organizations has been devoted recently to developing pollution-free processes for treating copper sulfide concentrates. A number of hydrometallurgical processes are in various stages of development and have been subjected to economic evaluation. Although the hydrometallurgical approaches eliminate SO2 emission problems, they create objectionable effluents and residues, make precious metals recovery complex, and are not very efficient for treating chalcopyrite. Furthermore, they are consumers of considerably more energy than pyrometallurgical processes which produce blister copper that can be electrorefined to commercial grade cathodes. This paper discusses a pyrometallurgical process under development by AMAX Base Metals Research & Development, Inc. (1) The original objectives set for the process development were: 1. Sulfur control of at least 95% with elimination of fugitive emissions. 2. Copper and precious metal recoveries as good as or better than conventional processes. 3. Low capital cost. 4. Competitive operating costs 5. Use of known proven technology where applicable.

Jan 1, 1976

By M. Tangstad, H. Mølnäs, J. D. Steenkamp

"Temperature affects several aspects of pyrometallurgical systems, including thermodynamics and reaction kinetics. Reliability of temperature measurements in laboratory and plant applications is thus important from process, safety and financial perspectives. This case study briefly introduces different techniques utilized for temperature validation, and demonstrates temperature validation on laboratory scale utilizing the wire-bridge method. Pt/Ptl3Rh thermocouple hot junctions were constructed by mechanically connecting thermocouple wires through a pure metal bridge consisting of copper, gold, nickel or palladium wire. When heating the wire-bridge thermocouple alongside a regular Pt/Ptl3Rh thermocouple, temperature offsets were quantified as the wirebridge thermocouple short-circuited at the melting points of the pure metals. At the melting points of gold (1064°C) and palladium (1555°C), average measured temperature offsets were -2.1°C ± 2.3°C and 0.2°C ± 0.4°C, respectively. Results from the copper and nickel wire-bridges were inconclusive. The paper concludes with a discussion on the potential industrial applications of the technique.IntroductionThermocouples are probably the simplest of all temperature sensors, but are widely utilized due to simplicity, versatility and ability to handle a variety of experimental conditions and industrial applications. Additionally, thermocouples are often the only option in research laboratories requiring high temperature measurements, and a high level of reliability is usually required from thermodynamic, kinetic as well as safety points of view.The study presented here originated from a test program where the compatibility between different types of carbon-based refractory materials and industrial slag produced in silicomanganese furnaces were investigated on a laboratory scale utilizing the static crucible test[l]. Due to the nature of the silicomanganese production process, the compatibility tests were to be conducted at 1600CC[2]. Details of the experimental set-up utilized for the compatibility tests are discussed in the Experimental Set-up and Method Statement section later in this paper."

Jan 1, 2012

By T. M. Dreher

The difficulties associated with the operation of a classical rhodium refining process have prompted many attempts to develop a viable solvent extraction flowsheet for rhodium. Recent investigations at McGill University have involved the activation of rhodium prior to its solvent extraction. The role of activation is to convert the aquochloro complexes of rhodium to a form extractable by conventional solvent extraction reagents. In the novel separation scheme identified, chloro complexes of rhodium are converted to bromo complexes, which undergo aquation to a lesser extent, making them more easily extracted. Rhodium is then extracted using Kelex 100, and stripping is achieved by use of a concentrated chloride based solution. Separation of rhodium from iridium is achieved by either prior reduction of Ir(IV) to Ir(III), as the latter is not extracted, or via co-extraction and differential stripping. A conceptual flowsheet for the refining of rhodium using this method is proposed.

Jan 1, 1998

By Lauri Holappa

Copper converting is mostly performed in Peirce-Smith converters. The process is still very similar to the original one developed in the early 20th century. It is a batch process in a horizontal cylindrical reactor with air blowing via tuyeres along the length of the reactor side. The Peirce-Smith converter has its roots in Bessemer's inventions in the 1850's as he tested both horizontal and vertical vessels for steel converting. However, for steel making a vertical pear-shaped converter with air bottom-blowing was established. In the course of time, there was a distinct necessity for oxygen usage instead of air due to harmful effects of nitrogen to steel properties and its cooling effect. In-bath blowing of oxygen did not succeed, however, and top-blown oxygen converter with oxygen lance (LD or BOF) was first developed in he 1950's and emerged rapidly to a dominating position. Somewhat later oxygen bottom-blowing via special shrouded tuyeres was developed (OBM or Q-BOP) but has attained only fractional share. Bottom-blowing technique had, however, impact on the current combined blown converters which adopted the benefits of both top and bottom blowing. In copper converting Peirce-Smith type converters have kept their position until today although new processes have been introduced and at least few of them seem to be emerging. In one respect copper converting has a clear leading position i.e. in the progress of continuous converting processes (Mitsubishi, Ausmelt). These processes utilise top-blowing lances instead of in-bath blowing tuyeres. A different principle for continuous converting is flash converting by Kennecott Outokumpu, which makes smelting and converting independent of each others. Solid ground matte is used as a feed for flash converting in a reactor shaft similar to Outokumpu matte flash smelting. A comparable process has been presented by Inco too. The paper discusses principal physico-chemical and process technical similarities and differences in copper and steel converting. Although these processes are metallurgically quite different it seems that during the modem history of ferrous and non-ferrous metallurgy, starting from the 1850's, the exchange of knowledge between these disciplines has been quite intensive. In long-term perspective, many similarities in the development can be found but also divergences due to different ambient circumstances.

Jan 1, 2003

By Veena Sahajwalla

The cupola furnace is a coke-fueled shaft furnace used as a primary melting unit in iron foundries. Control of chemical composition of the iron tapped from the cupola is a key factor in productivity and quality control. In an effort to develop a control model for the cupola, a fundamental approach based on physical and chemical principles has been taken to describe the melting process. The behavior of oxidation of the solid charge in the stack of the cupola has been studied. Sulfidation of the charge materials by sulfur-bearing components released to the furnace gases from the coke has been described. Carburization of metal droplets of iron and of steel in separate molten streams has been characterized. Finally, reactions with alloying elements in the hearth (well) of the furnace have been defined. These reactions have been described in a computer-implemented model developed to predict the composition of the iron tapped from the cupola. The model has utilized the thermodynamics and kinetics of the oxidation, sulfidation, and carburization reactions, including temperature and physical aspects, in the various zones of the melting unit. The model predictions have been compared favorably with operating results.

Jan 1, 1992

By A. G. Cecutti

A brief overview of the known significant health effects of both Nickel and Cobalt will be presented. Some time will be given to the current research activities, especially for Nickel. Emphasis will be placed on some of the controversial issues associated with their health effects.

Jan 1, 1988

By Denise Corrêa de Oliveira

Common dry batteries use zinc as the negative electrode. Producers commonly use additives such as mercury to prevent corrosion and to increase the mechanical resistance of the zinc anode. Alkaline batteries also contain it, as an anti-corrosive agent. When mixed with the common municipal solid waste, heavy metals as zinc and mercury pollute soil and ground water supplies, moving to the food-chain and affecting human health. Due to these possible damages, this kind of waste must be properly disposed, or recycled. Thus, even in low amounts (ppm) in batteries, mercury has to be eliminated or, at least, its content should be reduced. This work presents the use of pyromettalurgical processes, to reduce mercury content and recover zinc. The tests involved batteries treatment at temperatures from 300° to 1000°C. Mercury is eliminated up to 650°C, and zinc is evaporated at higher temperature treatment. C

Jan 1, 2001