Search Documents

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By J. D. Steenkamp

Keywords: Thermal, conductivity, diffusivity, expansion, history, density, specific heat capacity, industrial rich high-carbon manganese slag The thermal conductivity of slag is an important parameter in the design of furnace-containment systems based on freeze-lining technology. Literature indicates that the crystal content of a slag has a significant influence on its thermal conductivity. Industrial, rich, manganese-bearing slag was cooled at different rates to create samples with different microstructures. The coefficients of thermal conductivity of these samples were measured in a nitrogen atmosphere from room temperature to 990°C at 100°C intervals. The laser-flash measurement technique was used for this purpose. Follow-up investigations included XRF and XRD and modelling in FACTSage.

Jan 1, 2011

As in other countries, gold mining inNew Zealand has been cyclic in character. Looking at these cycles may provide insights as to what may occur in the future and that is the basis for this study.   New Zealand has experienced four gold mining cycles. The first began in 1857, peaked in 1866 and terminated in 1890. This cycle was characterised by alluvial gold mining by individuals and small groups. This is referred to as the Labour Led cycle. The second cycle began in 1890 and reached its peak in 1906 and terminated in 1929. This cycle was characterised by the use of dredges in alluvial gold mining and was also the peak of hard rock mining. This cycle is referred to as the Technology Led Cycle. The third cycle peaked in 1940. This cycle was far less significant than the previous cycles, arising out of the depression when the unemployed embarked on small scale alluvial mining. This overprinted the continuing decline that occurred after 1906. This cycle is here referred to as the Depression Overprint Cycle.   The fourth cycle began in 1984 when production began to climb rapidly from a very low base. The growth in production was spurred by rising gold prices in the early 1980s resulting in relatively low grade gold-bearing alluvial ground becoming economic. But in the 1990s, production from the new hardrock mines in Coromandel and Otago has overshadowed alluvial production. This cycle is here referred to as the Price Led cycle.   What are the future prospects for gold in New Zealand? Although there are many factors involved, this will be largely determined by two factors; firstly, continued access to prospective gold-bearing properties, and secondly, the price of gold. Based on these factors, three future industry scenarios have been developed. The first of these is industry collapse, in which access to prospective property is constrained and prices mayor may not weaken. The second is industry consolidation, in which the available ground is accumulated by a small number of large companies who can use economies of scale to weather price fluctuations. The third scenario is industry growth, in which access to prospective ground is constrained in environmentally sensitive areas but is otherwise relatively unconstrained. Efficient companies are allowed to work in a policy and economic framework that allows them to make a major contribution to the economy.   While the industry cannot control these critical factors, a good knowledge of the positive role gold mining could play in the future economy may provide a framework by which the access issue, in particular, may be addressed from a balanced perspective.

Jan 1, 1994

By Brad Marchant, Rick Lawrence, David Kratochvil

"BioteQ has successfully developed commercial operations for ARD treatment and selective metal recovery using the patented BioSulphide and Thiopaq® biological reduction technologies. The BioSulphide-Thiopaq process was developed to provide biogenic sulphide for the selective recovery of high purity metal concentrates from acidic wastewater, which are sold to recover capital costs and off-set water treatment costs. The BioSulphide-Thiopaq process can be used on a stand-alone basis or in conjunction with a lime circuit. Process advantages include: selective recovery of metals, very low metal concentrations in effluent, reduced waste sludge liability, reduced lime treatment costs and, in some cases, profitable sale of metal concentrates. Two case studies are presented to illustrate operations focused on metal recovery at the Caribou Mine, New Brunswick, Canada, and at Phelps Dodge, Arizona. A third case study is presented to highlight environmental control as well as metal recovery for treatment of ARD at the Raglan Mine in Northern Quebec. Process flowsheets, capital and operating costs are presented for the three case studies.INTRODUCTIONProtection of water quality has become one of the most important environmental challenges facing the mining industry. Although new mining projects can be designed to minimize impacts to the environment, many existing and abandoned mining operations have water quality problems. The principal cause of water contamination is acid rock drainage (ARD), which is generated when residual sulphide minerals in waste rock, tailings and other mine components and products are exposed to air and water. These reactions can produce acidity and elevated concentrations of metals in drainage and seepage that can adversely affect surface and groundwater resources. To meet regulatory criteria for water quality in the receiving environment, many mine operators must consider treatment of mine water and other effluents prior to discharge."

Jan 1, 2003

This paper provides an update to a paper by the author on an overseas explorer's perception of New Zealand, presented at the 1997 New Zealand Minerals & Mining Conference. New Zealand has one of the most open and internationally competitive economies in the world. The petroleum exploration industry in New Zealand is booming with a record number of wells planned for 2000. New Zealand is keen to encourage investment in mineral exploration to develop its natural resources. A study of the geological potential of New Zealand estimated the value of known and potential resources of metals at $86 billion. Gold has the greatest potential, with a total resource estimated at $33.5 billion. The price of gold has averaged NZ$554 since the beginning of 1998, and NZ$593 in the last year, which is very competitive with other countries. An assessment of country risk compared New Zealand with twenty other countries in ten risk categories: sovereign risk, land access, environmental issues, land claims, mining legislation, social risk, infrastructure, civil unrest, natural disasters and workforce. New Zealand ranked fifth, showing it has low country risk. This provides a high degree of certainty for investment, which is important for the perception of New Zealand as an exploration destination. Corruption was considered separately, and New Zealand ranked third out of ninety countries, showing it is one of the least corrupt countries in the world. New Zealand has a favourable business environment, good geological potential, low country risk and no corruption. Despite this, New Zealand has not registered on the radar screens of overseas mineral explorers, and the positive factors appear to have been overlooked. New Zealand has considerable undeveloped mineral potential, and with the current rise in commodity prices, it is hoped New Zealand can participate in a resurgence in mineral exploration.

Jan 1, 2000

By H. C. LIVINGSTON

At the Hanna No. 4-A mine of The Union Pacific Coal Co. a new system of trackless mining is being utilized to extract a 26-ft coal seam. By using shuttle cars and a conveyor belt for haulage in the rooms and panel entries instead of pit cars and panel hoist a saving of 12 cents per ton is expected. Mining is conducted in a 26-ft coal seam laid down on a synclinal structure with active workings on a pitch of approximately ten to twelve degrees. The coal seam is interbedded between a shale bottom and sand- stone top. The coal is friable, high in moisture, and subject to spontaneous combustion. The mine is rated gassy by the State Coal Mine Inspection Department. Mining is conducted at the present time by unbalanced rope haulage an main slopes spaced on approximate 4300-ft centers with the three-entry system driven to boundary lines, strike entries being turned on approximate 1300-ft centers. Panels are driven to the rise between entries at approximately 750-ft intervals with panel rooms driven on the strike 500 to 600 ft long, leaving 150 ft of barrier pillar between each block of panel rooms.

Jan 1, 1949

By J. E. Chilton

A technique for use in underground coal mines measures the response times of machine-mounted methane monitors. This technique uses a calibration cup to deliver gas to the sensor head to measure response times. For comparison, in the current study, response times were measured by placing methane sensor heads in a specially designed test box where they were exposed to an atmosphere containing a constant concentration of methane. Response time readings measured in the test box were shorter than the readings obtained using the calibration cup. The response times measured in the test box were comparable for sensors from three different manufacturers. The effects of dust cap and flame arrestor design on response times were also evaluated using the test box.

By B Hiebl, J Martens, L Petzold

A research team at the Iron and Steelmaking department at Primetals Technologies has established new upgrading measures for improving the efficiency of the beneficiation process in ironmaking plants, relying largely on pre-existing equipment. After the upgrade, the iron content in the final iron ore concentrate was shown to be significantly higher. Remarkably, the costs for employing the respective measures are surprisingly low.This case study is based on a Kazakh iron and steel producer, whose beneficiation process is currently generating a magnetite concentrate with a final iron content of 65.65 per cent. The study shows that the implementation of Primetals Technologies’ intelligent modification measures to the current beneficiation process, the realisation of more effective dewatering, and the utilisation of an innovative binder lead to an increased iron content in the resulting pellets, reaching a concentration of 69.17 per cent (iron ore concentrate) and 66.5 per cent (pellets).The current operation consists of three closed circuit grinding stages, four stages of low intensity magnetic separation, vacuum disc filters and straight-grate pelletising. By dividing the slurry after the second stage of grinding and the third stage of low intensity magnetic separation, it is possible to divert the more iron-rich fines before they would enter the third grinding stage and the fourth stage of magnetic separation. This then reduces the load on the existing third stage ball mill. Afterwards, the ground material is treated in an additional low intensity magnetic separator and mixed with the previously diverted fraction of the fines. An improved filtration procedure, combined with the application of a highly sophisticated binder, further reduces the amount of additives needed, so that a genuine direct reduced (DR)-grade iron concentrate is produced as a result.All laboratory, pilot and pelletising test work was executed at Primetals Technologies’ laboratories in Austria.CITATION:Martens, J, Petzold, L and Hiebl, B, 2017. Enabling iron ore concentrate for the production of direct reduced iron with pre-existing beneficiation lines, in Proceedings Iron Ore 2017, pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G. E. Agar, W. B. Kipkie, R. A. Tenbergen

"This paper describes the successful pilot plant testing of a flowsheet, developed at INCO Ltd.'s J.Roy Gordon Research Laboratory (JRGRL), for improved separation of the constituent minerals in a bulk copper nickel concentrate.The flowsheet utilized the fact that xanthate concentration on the mineral surfaces is the most important variable affecting the high lime separation and that reduction of the xanthate concentration could be effected by an oxidative conditioning stage.When the adsorbed xanthate was reduced to a suitably low level, chalcopyrite and pyrrhotite could be floated to leave a high grade nickel concentrate as the residue. Sodium cyanide was added to the froth product to depress pyrrhotite and any remaining pentlandite. The temporary depression of chalcopyrite by the sodium cyanide was overcome by introducing a conditioning step following cyanide addition. The advantages of the flowsheet; improved copper-nickel separation, operation without heating of the pulp, production of both high grade nickel concentrate ( 29. 5% Ni, . 26% Cu) and copper concentrate ( <O. 5% Ni, 30% Cu) were all realized."

Jan 1, 1984

By Charles Zdazinsky

Over-break is undesirable in underground civil construction because it excessively damages rock along the perimeter of the tunnel, which directly influences the cycle times of advancement. A quicker cycle time for each process is required to optimize the operation and therefore minimizing over-break is essential for operational success.

Jan 1, 2015

By T. Watanabe, S. Hayashi, M. Hayashi, K. Nagata, H. Fukuyama

Chemical states of fluorine in CaO-SiO2-CaF2glasses in a composition range of CaO/SiO2=0.5?1.3 and 5?25 mol%CaF2have been investigated by 19F solid-state NMR with and without MAS. The isotropic chemical shifts of the glasses are close to those of cuspidine crystal (59.4 and64.3 ppm with respect to C6F6) and CaF2crystal (58.6 ppm). The fluoride ions are coordinated with four or less than four calcium ions in this composition range. The chemical shifts move to the lower frequency with an increase in the CaF2content, whereas those are not affected by theCaO/SiO2ratio. The ionic distance between calcium and fluoride ions increases with an increase in the CaF2content. The chemical state of fluorine is not disturbed by the degree of polymerization of the silicate network. Comparing the MAS and static NMR spectra, the second moment attributed to 19F-19F dipole-dipole interaction has been estimated. The values of the glasses range over 3.1?7.3107Hz2andthose are larger than the calculated value of cuspidine crystal. This indicates that fluoride ions form Ca-F clusters in the glasses and that the size of clusters increases with increasing the CaF2content. Keywords: chemical state of fluoride ion, CaO-SiO2-CaF2glass, solid state 19F NMR spectroscopy

Jan 1, 2004

By Jack Curran

KANSAS CITY, MO - Performing one of the most impressive urban building-implosion projects in recent memory, Tulsa, Oklahoma-based Dykon Explosive Demolition Corp. and Omaha, Nebraska-based Anderson Excavating recently felled the landmark Columbia Bank Building in downtown Kansas City, Missouri, USA. Although every structural blasting project presents special challenges, this undertaking was most notable for its unusually unique structural design, tight clearances, and high risk to adjacent structures.

Jan 1, 2003

By R. G. Gürtunca

Over the past century coal miner safety and health has seen tremendous improvements, the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006 which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

Forecasting, particularly when applied to meaningful issues, is known irreverently as &apos;futurology&apos;. There is quite a range of opinion ext.ant in the world when mineral resources are looked at. The opinions range from the doomsday view that there will be acute shortages of all essential commodities, to the optimistic outlook that new &apos;discoveries will prevent any possibility of shortages. The environment is, as yet, only studied locally and quite parochially; surprisingly there is little integration when considering the spatial atmosphere, the seas in depth and the earth&apos;s crust.

Jan 1, 1981

Systemic process mineralogy study on Baerbulawu refractory hematite ore in Kazakhstan has been carried out. The ore contains Fe 41.34%, and 87.26 % of which exists in hematite. Most hema-tite occurs as fine or ultrafine grains and its average size is only 0.015mm. The gangue is mainly composed of quartz, mica, chlorite, kaolinite and other clay minerals. The liberation of hematite is only 66% when the ore is grinded to 75% ?0.074mm, while part of gangue is already liberated from hematite under this grinding condition, so these gangue can be cast away by magnetic separation in advance. Hematite will not liberate completely from gangue untill grinding fineness reaches 86% ?0.038mm, at the same time, free particles of ultrafine hematite tend to coagulate randomly with quartz and clay minerals, so appropriate dispersant is necessary to pre-vent hematite and clay minerals from coagulation. Based on the process mineralogy research, final technology flowsheet is high-intensity magnetic separation by coarse grinding?rough magnetic concentrate regrinding?inverse flotation, and an ideal index is achieved. The yield of final iron concentrate is 43.46%, and its grade and recovery are 66.76% and 70.55% respectively. The research result is also useful to other similar iron ores.

Jan 1, 2014

By Benoit Bissonnette

"The need for production of a competent fill was recognized early by the project partners. Consequently, a 4000 Ud paste fill plant was constructed and commissioned in early August 1994.In order to fine tune the process without risk to the underground workings, a closed pumping loop was devised on surface. After two months of this exercise, the first underground slope was filled according to specifications obtained from the pilot plant trials.This paper will focus on the operational problems encountered and the solutions adopted so far, and on a comparison between expected and actual fill production and characteristics.RésuméLa nécessité de produire un remblai de propriétés mécaniques suffisantes a été rapidement reconnue par les partenaires du projet. Conséquemment, une usine de production de remblai en pate, utilisant les residus du concentrateur d'une capacité de 4000 t/j a été construite et l'opération a débuté au mois d'aôut 1994.Dans le but de roder le précedé sans mettre en danger les installations souterraines, l'usine a été testée dans un circuit de surface. Après deux mois d'essais, le premier chantier souterrain a été rempli avec du remblai en pate selon les specifications dérivées de l'usinage pilote.Cet article présente les problemes d'opération rencontrés et leurs solutions, en plus de faire une comparaison entre les résultats prévus et ceux actuellement obtenus sur la production et sur les charactéristiques du remblai."

Jan 1, 1996

By Mike D. J Bonneau, Malcom Jr Ford

Rietspruit Opencast Services was one of the first opencast coal mines to successfully employ cast blasting to aid in the burden removal operation. Initial work on cast blasting began at the mine in 1980 and has developed to a stage where approximately 26% of the total burden material is cast to a point where handling by draglines is no longer required.

Jan 1, 1991

By H Saw, M Cordova

Cemented rock fill (CRF) is often used to support open stope voids. This allows for the full recovery of ore while achieving global mine stability. In such cases, the exposed CRF masses require adequate compressive strength and stiffness to resist the forces and limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or development mining waste. This means that conventional laboratory samples cannot be readily used to determine the laboratory strength. Consequently, a research project was undertaken to determine the influence of sample size on uniaxial compressive strength. This paper presents the results from CRF samples that were prepared using the same mix design and then cast into moulds with diameters of 150, 240, 300 and 400 mm. The laboratory testing also allowed a better understanding of the effect of particle size distribution upon the overall strength of a rock fill mass. The laboratory results were compared to a database of large-scale results from the testing of fill masses from a number of mine sites.CITATION:Cordova, M, Saw, H and Villaescusa, E, 2016. Laboratory testing of cemented rock fill for open stope support, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 755–762 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011