Search Documents

By R. Karl Zipf

Multiple seam mining interactions caused by full extraction mining, whether due to undermining or overmining, frequently involve tensile failure of the affected mine roof. The adverse ground control conditions may prevent mining for both safety and economic reasons. Prior researchers have identified the geometric, geologic and mining factors controlling multiple seam mining interactions. This numerical study examines the mechanics of these interactions using a modeling procedure that 1) incorporates the essential constitutive behavior of the rock such as strain-softening of the intact rock and shear and tensile failure along bedding planes and 2) captures the geologic variability of the rock especially the layering of weak and strong rocks and weak bedding planes. Specifically, the numerical study considered the effect of vertical stress, interburden thickness, and the immediate roof quality of the affected seam in both undermining and overmining situations. The models show that for overburden-to-interburden thickness (OB/IB) ratios of less than 5, interactions do not occur, and that for OB/IB more than 50, extreme interaction is a certainty. In between, the possibility of an interaction was found to depend on gob width-to-interburden thickness ratio, site specific geology and horizontal stress to rock strength ratio in addition to the OB/IB ratio. The models also showed that horizontal stress was profoundly altered well above or below a full extraction area and that these changes are likely to influence the success or failure of multiple seam mining. The role of horizontal stress in multiple seam mining interactions has received little attention in prior investigations. Four factors control the mechanics of multiple seam mining interactions: 1. vertical stress concentration 2. horizontal stress concentration 3. stress re-direction 4. bedding plane slip bands A combination of vertical and horizontal stress increase and high stress gradients in the vicinity of full extraction areas re-orients principal stresses into a very unfavorable direction. This seemingly small stress re-orientation has a profound adverse effect on bedded rock.

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

By B. Samanta

This paper investigates the performance of the neural network technique in a placer deposit situated at the Nome district in Alaska. Initially a single neural network model was constructed to estimate the gold grade. However, at a later stage, an ensemble model consisting of multiple networks was also constructed via the Adaboost algorithm. The reason behind the use of the ensemble model of the Adaboost algorithm was to examine if the ensemble model provided superior performance to the single neural network. As indicated by other studies, Adaboost did not have a better performance than a single neural network in this specific application. This may be due to the high noise inherent in the gold data used in this project. Consequently R2 values of gold prediction are also poor for both the single and multiple networks.

Jan 1, 2005

Core samples, which were collected by the author from the Busang prospect, East Kalimantan, reflect a progressive evolution of a large magmatic-related hydrothermal system that is comparable to that encountered in many similar systems elsewhere in the Pacific region. The initial, localized deposition of sheeted porphyry quartz-molybdenite veins took place at high temperatures and fluid salinities, and at relatively deep levels. This was followed by an extensive phase of phyllic (sericite-quartz-pyrite ¦ tourmaline-apatite) wallrock replacement and vein formation. Propylitic (epidote-chlorite-carbonate-quartz) alteration was formed marginal to the phyllic assemblages. These porphyry-related events were centred in the Southeast Zone, and are probably associated with the emplacement of a felsic intrusion at depth. This event contributed only trace gold to the system. The early stages of hydrothermal activity were followed by an episode of quartz (¦ adularia) û carbonate û base metal sulfide veining, which was accompanied by argillic (illitic-kaolin clay) wallrock alteration. This event was sulfide-rich in the Central Zone and carbonate-dominated in the Southeast Zone. Gold mineralisation was observed in Central Zone drillcore to be associated with both sulfide, as well as carbonate, deposition. A final stage of epithermal-style quartz ¦ stibnite û realgar veins are, in the Central Zone, locally gold-bearing. The latter two events are interpreted to be associated with the late-stage exsolution of metal-bearing brines from the felsic intrusion that formed the earlier porphyry quartz-molybdenite veins and widespread phyllic-propylitic alteration.

Jan 1, 2002

A New Technology of Applying SLon-2500 Magnetic Separator to Recover Iron Concentrate from Abandoned Tails

Sep 13, 2010

By Viviane Tavares

The technology advance of mobile devices makes consumers of these equipment do more constant exchanges, with this the obsolete devices discarding becomes an environmental problem, due its landfill accumulation. In order to minimize the environmental impacts caused by these equipment there?s the recycling necessity of polymers, ceramic and metallic materials. The main goal of this recycling is to study the printed circuit board of device mobile processing through ore treatment in order to recoup copper. Initially printed circuit boards were processed in a knives mill, in order to liberate the ferrous material, after that it was done the magnetic separation of the reduced residue. With the not magnetic fraction it was done the grain sized analysis and sulfuric acid and hydrogen peroxide leaching analysis. With the chemical analysis results proceeding from the leaching aliquot it was possible to observe that the leaching method with sulfuric acid and hydrogen peroxide presented greater copper recovery.

Jan 1, 2009

By Lucas Gonçalves Generoso, Larissa Rodrigues de Carvalho Rocha, Mauro Vivaldino Fernandes, Gustavo Serrano dos Santos, Gustavo Alexandre da Costa Manso

O Alto-Forno 3 da Usiminas iniciou sua atual campanha em 1999. Projetada para durar 15 anos de operação, previa-se uma produção de 41 Mt de gusa. A partir de 2008, iniciaram as avarias mais significativas no sistema de refrigeração, possibilitando a entrada de água e os consequentes distúrbios operacionais. Buscando estender a atual campanha até 2021, a Usiminas realizou, dentre outras atividades de preservação, duas trocas de staves, em 2015 e 2018. Neste trabalho, são apresentados o planejamento e os principais procedimentos relacionados à parada operacional do alto-forno para a segunda troca de staves, com foco nas atividades operacionais que permitiram a redução do nível da carga até 25,1 metros em relação ao stock line. Destacam-se os cuidados e o êxito no abaixamento de carga até o nível das ventaneiras e a metodologia de troca de staves adotada. Por fim, a previsão de extensão da campanha em 7 anos, possibilitará atingir uma produção acumulada de 53,5 Mt, superando em 12,5 Mt o valor projetado.

Oct 1, 2019

According to the Darcy?s law, filtration rate should increase with increasing pressure drop (?P) across a filter cake. In centrifugal filtration, ?P is created by the free water present on the surface of a filter cake. Thus, ?P can become negative when the free water disappears from the cake surface, which makes it difficult to achieve low cake moistures. In the present work, we have developed methods of overcoming this problem by either increasing the air pressure inside or applying vacuum outside a centrifuge. Laboratory dewatering tests conducted using these provisions showed that the moistures of various minerals and coal fines can be reduced to the level that can obviate the need for thermal drying. The new concept has been successfully tested both at pilot- and full-scale, which lead to commercial deployment through Decanter Machine, Inc., under the trade name Centribaric® centrifuge. Keywords: dewatering, hyperbaric centrifuge, pressure drop, Darcy?s law, Centribaric® centrifuge

Sep 1, 2012

By J. L. Deutsch

Block model estimates are commonly calculated by the well-established technique of kriging. The mathematics are well established, but implementation details require site-specific considerations. Checking and measuring the performance of the estimates is important to ensure the block model is suitable for its intended purpose. There are different criteria for long-term planning and short-term planning. The implementation of kriging should be checked with cross-validation and assessed for conditional bias and departure from theoretical optimality with the calculation of kriging efficiency. A new expression of kriging efficiency, which compares the kriging variance with the theoretically optimal kriging variance, is developed to aid in this assessment. The assessment tools presented here can be applied in a number of situations; however, ordinary kriging with a reasonably large search performs well in most cases.

Jan 1, 2014

By M. Javier

Mining is an industry of experimentation throughout human history. Recently, societies are giving a clear message about mining because many projects are being rejected around the world. These refusals are a generational reaction to the activity of mining. In practice, it generates the perception that mining is using the same methodology without attending to the gradual initiation of conflicts. This is in spite of the best engineering and technology of the time that are put in place at the presentation of those mining projects. Some of these rejected projects are geographically distant from each other, but the communities? rejection occurred during many cases under similar characteristics. This concern shows that the current model of mining projects needs to be replaced with a new one: A new Design, one within which the socio-environmental values of this millennium are inherent. This paper describes Mining Project 101 to help the industry to set the highest and cleanest standards for mining. It also presents its aspects to sustainability and nature, which provides the principles and procedures for designing, planning, and operating mining projects with sensitivity to nature. It offers methods of diagnostic, remediation, and extraction while at the same time preventing and preserving a physical, chemical, and biological equilibrium of nature. This emerging process will be a step up from having a mining industry unaccountable to the socio-environmental conflicts it perpetrates and will abandon the ?cosmetic? repair on the caducity of traditional models in today?s practice. In conclusion, we have the opportunity to change this model. KEYWORDS: Equilibrium in Nature, Geomímic, Deproduction, mine design.

Feb 27, 2013

By S. Mundike

A scraper-based block cave method has been successfully applied to extract the Lower orebody at Nchanga since the 1950s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas, the 2420 8E 1C trial drift, was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre-reinforced shotcrete was extended to other drifts. This paper describes the application of fibre-reinforced shotcreteat Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

By Ira L. Wright

This paper describing the milling practice of the Black Hawk Consolidated Mines Co., is one of a series being prepared by the United States Bureau of Mines. ACKNOWLEDGMENTS Part of the information contained in this paper was furnished by I. H. Stanley, mill superintendent, Black Hawk Consolidated Mines Co., Hanover, M. M., and a part by the South-western Engineering Corporation, Los Angeles, Calif. The assistance of T. G. Chapman in arranging the paper for publication is also acknowledged.

Jan 1, 1930

By Hillis R

As part of BHP Iron Ore's policy and goal of achieving a high standard of environmental management within its operations, a protocol for mine closure has evolved. The need to demonstrate sound environmental management with respect to site decommissioning meant that a comprehensive, environmentally sensitive closure protocol was required. Within this framework, a four-phase protocol was developed, the first phase was the determination of objectives in relation to site rehabilitation and end land use. The second phase was the determination of the process required to achieve these objectives. The third phase was the application of this process in a site specific manner. The fourth and final phase was monitoring of the site with regard to the achievement of determined objectives. The protocol was originally developed to direct the closure and decommissioning of the Goldsworthy site in 1992. This being the first total site decommissioning for BHP Iron Ore. Since that time the protocol has been successfully utilised for the closure of the Yampi (Koolan Island) operations (in 1993/94) and the Shay Gap/Nimingarra Operations (in 1994/95).

Jan 1, 1996

By Paul Sterling

1. INTRODUCTION. THE general impression regarding the preparation of merchantable anthracite is that it is confined to a colossal, grimy structure, called a "coal-breaker." This name is misnomer; for the desired result is not to break the coal, but to prevent its being broken. Preparation may be said to begin at the face of the chamber, with the mining and loading of the coal. Local conditions vary, not only in the same field or basin, but also in the same mine, so that there is no fixed empirical rule governing the method of blasting or cutting coal. Tests should be made, when possible, to determine the explosive, or the mechanical coal-cutter, which will produce the largest percentage of what are locally known as " lump " and " prepared sizes " of anthracite. The prepared sizes are those mostly consumed for domestic purposes. All other sizes might be called by-products of the anthracite industry; for they are not especially desirable, being the degradation resulting from the mining and handling of a brittle or laminated material. Being low in volatile combustible matter, anthracite burns most successfully when nearly of a uniform size, permitting the easy passage of air through the voids. This accounts for the large number of sizes into which the coal is separated. Table I. gives the various sizes, the diameter of ring over and through which each size is made, and the usual purpose for which it is employed.

Oct 1, 1911

By F. H. Deist, M. P. Roberts

"The Collieries Research Laboratory of the Chamber of Mines of South Africa is developing a coherent system of programs to aid in the full spectrum of activities arising in the planning of new as well as operating mining enterprises. It is the purpose of this paper to describe the design and application of two subsystems in the complex.One of these subsystems is an initial version of a production simulator. This program draws upon a model of a mining enterprise and simulates the operational and financial aspects of a set of alternative mine production plans.These plans are specified in terms of proposed sequences of operations. Details such as reserves, production rates, resource requirements and so on, are taken from the model.Physically, the model takes the form of a cross-referenced data base, maintained by means of a general file maintenance system which is another subsystem described.The paper concludes with a description and analysis of the first practical application of the two programs."

Jan 1, 2014

The interaction between ore-bearing fluids and the siliciclastic rocks typically hosting orogenic gold deposits in Phanerozoic metamorphic terrains result in the development of a distinctive alteration halo. Along with petrological changes such as the replacement of chlorite by carbonate and the growth of sericite, characteristic geochemical modifications take place within this alteration envelope. These include variations in elemental abundances and more or less pronounced shifts in the H, C, N, O, and S isotopic signature of the ore system. æFingerprintingÆ these isotopic trends can provide exploration with additional vectors towards the ore zone, and yields valuable information regarding the source of the hydrothermal fluids and the solutes contained therein. Data from radiogenic isotope systems such as Sr-Rb, Ar-Ar, Xe-Ra, Pb-Pb, Re-Os, Sm-Nd, and U-Pb can constrain the kinematic history of ore-hosting structures, provide important clues concerning the absolute timing of gold emplacement, and enable the detailed characterisation of associated intrusives with respect to their magma source(s) and crystallisation age. Although high analytical costs, long turn-around times and the potential for misinterpretation prevent isotope systems from offering a æquick & dirtyÆ analytical method that would provide a significant advantage in exploration for orogenic gold mineralisation, the development of integrated four-dimensional ore genesis models depends heavily on constraints obtained from isotope mass spectrometry.

Jan 1, 2002

By Magno Rodrigues Ribeiro, Alexandre Cabral Stelzer, Cacio José da Silva, Leonardo Nogueira Ferri, Marcelo Ciminelli Mendes, Christophe Bouché, Marco Aurélio Soares Martins, Evenilson Soprani Lopes, José Xavier da Silva Filho, Sérgio Luiz Dalvi

Since 2001, CVRD is carrying out a modernization project in it’s pelletizing plant’s automation systems, that comprehends instrumentation, control and information systems. In addition, the project includes implementation of advanced control systems, using artificial intelligence techniques, including fuzzy logic, expert systems and dynamic physical models, to increase production, reduce fuel and energy consumption and improve quality. This paper reports CVRD’s experiences in carrying out an optimization project.

Jan 1, 2005

concentrations) and physical nature of receiving streams, which in turn affects the stream ecosystem. Benthic macroinvertebrates are used to illustrate these impacts, and to investigate natural recovery in affected streams. In Charming Creek, a severely impacted stream in the Buller District, the macroinvertebrate community recovers diversity and the proportion of sensitive species (EPT) in the community is more significant with increasing downstream distance from the source of AMD. This is most likely due to dilution of AMD contaminated water by tributaries to the Charming Creek mainstream. Other impacted systems with less dilution from tributaries did not display similar levels of recovery. The effectiveness of remediation products BauxsolÖ and Zeolite was investigated using laboratory trials. Both products mitigated the toxicity of AMD and enhanced the survival of mayflies exposed to AMD contaminated water. Such products may be of use in the New Zealand environment but are likely to be most effective in conjunction with other systems (eg wetlands). Mitigating the impacts of AMD on stream ecosystems needs to include systems to directly address water chemistry issues (low pH, high metal concentrations) as a component of a holistic approach to restoring environmental conditions.

Jan 1, 2003

By G. Deissman, S. Kistinger

For the last 15 years environmental Life-Cycle Assessments (LCA) have increasingly been used to evaluate the environmental performance of industrial processes and products and have been employed as a basis in decision making processes in the public and industrial sector. However, assessment methodologies for environmental protection measures and reclamation/remediation measures with respect to their consumption of natural resources are generally poorly developed. In this presentation a methodology for LCA of environmental protection measures and remedial actions, respectively is suggested, using the remediation/reclamation of mining sites as an example. Key aspect of this approach is the development of an evaluation method appropriate for environmental protection measures, which links the various impact indicators recognised in the impact assessments and allows their integrated assessment.

Jan 1, 2005

By Paul Kunze

For some of us, the most disagreeable part of being the blaster- in - charge is doing the required paperwork. Cost coding on time cards, drilling reports, magazine inventory logs, and blast records all eat into our time. When all goes well, which I suppose is 98% of the time, the blast records are submitted and filed, probably never to be seen again. Sometimes a progressive operation will use the information documented in the blast reports to evaluate blasting effectiveness and improve results. When the report is consistently used in this fashion, costs can be reduced and other efficiencies will be realized. A blast report in times past was a simple form that mainly was used to keep track of the drill footage and of the powder used in the shot. However, as the population and consequences of careless blasting increase, multiple levels of blast documentation are now being required nearly everywhere, during all phases of the drill and blast process. We are now compelled to create preliminary blast designs prior to commencing work. We are required to submit pre-blast plans before each shot, and we need to generate post-blast reports that document the details and results of each shot.

Jan 1, 2004