Search Documents

By Dominic Fragomeni, Tony DiFeo, Martyn P. Hay

"As part of an investigation into flotation modelling of industrial scale operations, Falconbridge Ltd organised a “blind” test of the SUPASIM flotation model developed by Eurus Mineral Consultants (EMC). Two sets of rougher rate data, a flowsheet and the number and size of cells in the rougher bank were supplied from a plant that had been previously surveyed in November 2003. The name of the plant, cleaner circuit details and circuit mass balance were, at the time, unknown to EMC. With only these data, flotation performance was simulated and the cleaner circuit sizedFalconbridge then compared predicted and actual float performance and mass balance and found that final concentrate recovery and mass and circuit cell volume matched closely. Simulated recoveries relative to actual were +0.4% Cu, +0.1% Ni and -0.7% Co. However, prediction of metal distribution in the internal streams making up the various circulating loads showed some sizeable errors. On this initial success, the trial was extended and additional float test data for rougher feed, cleaner feed and cleaner scavenger feed was generated on site in April 2005. Further simulations significantly improved prediction accuracy for metal distribution in the internal streams. The average difference between predicted and actual recovery for all streams was reduced from 10.5% to 0.4%. This updated simulation was then used to ascertain the impact on final recovery, grade and plant circulating loads of increasing feed tonnage from 114 to 150t/hr. A number of scenarios were simulated in order to understand the contribution that (a) the fast and slow floating fractions and (b) regrinding of cleaner tailings are making to overall plant recovery.Simulation was then used to determine how much the flotation kinetics of both rougher feed and cleaner scavenger feed have to increase in order to deliver a 1.5% improvement in overall plant recovery. These improved kinetic values provide a target for laboratory testwork and operating conditions can be varied to determine how best to achieve these new values of fraction and rate."

Jan 1, 2006

By Enrui Dai, Weibing Chen, Bin Yang, Wenhui Ma, Haisheng Fang, Hui Wang

LiMn0.8Fe0.2PO4/C composite was prepared by an improved solid-state method and the effect of calcination temperature on properties of the obtained materials was investigated. The results showed that increasing calcination temperature from 600 to 700 oC improved the performance of the LiMn0.8Fe0.2PO4/C due to enhanced crystallinity and increased conductivity, but further increase in calcination temperature to 800 oC led to degraded performance due to particle growth and decrease in porosity. Therefore, the LiMn0.8Fe0.2PO4/C composite prepared at 700 oC exhibited the best electrochemical performance, and could deliver a high capacity of 152 mAh g−1 at 0.1 C, 147 mAh g−1 at 1 C and 114 mAh g−1 at 10 C. In addition, the performance of the LiMn0.8Fe0.2PO4/C and LiMn0.8Fe0.19Mg0.01PO4/C was compared when they were obtained at the optimum calcination temperature.

Jan 1, 2015

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

By S. J. Swart

This paper discusses the principles and application of risk assessment and management as the basis for environmental management within the mining industry. Unlike in other industries, mines are required to obtain closure certificates in terms of section12 of the Minerals Act, which should ultimately release them from further environmental responsibilities. It is emphasized that the concept of environmental risk assessment and management, when applied correctly will mean that the mine will be identifying and managing environmental issues beyond those set by current legal requirements and management strategies. The focus shifts from conventional minimum legal compliance management to management of real environmental risks. The advantage of this approach is that the perceived ?shifting of legal and management goal posts? due to changing environmental laws or management principles, will not influence or dictate the mine?s short or long-term management objectives or actions, mine closure funds can be more accurately determined and mine closure should become a relatively simple procedure. The risk assessment approach has been applied to the planning of mine closure at Iscor?s Durban Navigation Collieries (Durnacol) in Kwa-Zulu Natal and certain key risk issues such as the long-term risk of water pollution from coal discard dumps have already progressed to fully quantitative risk assessment. This paper will discuss the process, which has been followed to date, with particular emphasis on the most recent phase, namely quantitative risk assessment and management of pollution from coal discard dumps. It is believed that the approach that is being pioneered at Durnacol and which overcomes some of the more obvious deficiencies of both the EMPR and the traditional IEM process will ultimately serve as the model for all responsible mines in South Africa. It is also believed that this approach will enable the authorities to issue closure certificates with the confidence that there will be no unforeseen surprises in the years after closure.

Jan 1, 1998

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

"Different hydrometallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2 (Vegliò and Toro, 1994). An innovative acid reductive leaching carried out in soft experimental conditions was here considered using agro-industrial wastes containing carbohydrates as reducing agents (Vegliò et al., 1998).The leaching process was investigated from a kinetic and equilibrium point of view in order to optimize the experimental conditions and obtain high purity and concentrated MnSO4 solutions.The overall leaching process (not considering the complex network of intermediate oxidation reactions of the carbohydrates in hot sulphuric acid medium (Vegliò and Toro, 1994)) can be described by the following reaction:24 MnO2 + C12H22O11 + 48 H 24 Mn2+ + 12 CO2 + 35 H2O (1)A Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis and BET surface measurements before and after leaching.Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydroalcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions."

Jan 1, 2003

By J. C. Yingling, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Much of the land reclaimed since enactment of the 1977 Surface Mining Control and Reclamation Act is over-compacted. Research has shown that excessive compaction in replaced growing media is detrimental to establishment of trees. If trees are to be grown on reclaimed surface mined sites, something must be done to alleviate this excessive compaction. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed growing media. The University of Kentucky has developed test cells on reclaimed sites at a surface mine in eastern Kentucky to determine the impact of tillage (ripping) on soil compaction and tree survival rate. The ripping methods being evaluated include shallow tillage using conventional farm equipment and deep tillage using a dozer with a ripping arm. The impact of organic soil supplements on soil physical properties and tree survival rates is also being evaluated at the site. The organic soil supplements being evaluated include application of hardwood bark and application of straw and mulch. Each test cell has been planted with various species of trees, and for the first two years, data have been collected at these test cells for soil dry bulk density, penetration depth and resistance, and survival rate of trees. These data are currently being correlated to determine how ripping and the application of organic soil supplements affects the relationship between soil compaction and tree survival rate.

Jan 1, 2002

By J. R. Alldredge

This Bureau of Mines report presents a computer code that has been developed for describing and testing the statistical distribution of general continuous data sets. The statistical distributions used include the normal, lognormal, exponential, chi square, gamma, and uniform. Histograms for observed and expected values are plotted for each distribution. An example using geologic data obtained from a study of the geometric properties of natural fractures in oil shale rock illustrates the use of the computer program, GDIST.

Jan 1, 1977

By M. D. Aldridge

The results of designing, constructing, installing and operating a ventilation monitoring system throughout an entire commercial coal mine is presented. Measured parameters were airflow, methane, carbon monoxide, temperature, relative humidity and differential pressure. A central computer provided for automatic system operation. Preliminary tests of two remotely controlled ventilation regulators were performed in conjunction with the monitoring system.

Jan 1, 1977

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By J Seppelt, B Akerstrom, A Rice, J Bubnich, T Waters

The Concentrator 1 plant at Cadia transitioned from Cadia Hill open pit to the Cadia East block cave ore body in 2013. As a result of this change, major plant upgrades were required to achieve the desired throughput while treating more competent ore. The 40-foot (40’) SAG mill now receives a feed of predominantly high pressure grinding rolls (HPGR) product with a minor component of secondary crushed ore at a combined F80 of 17 mm. The significant reduction in feed size to the SAG mill has markedly changed the operating characteristics of the mill, which has been extensively studied since commissioning in 1998.This paper examines the operation of the 40’ SAG mill in its new configuration in the Concentrator 1 circuit. Operational stability is highlighted as a significant factor in delivering mill performance, which has been achieved through several key improvement projects utilising a theory of constraints framework. Five years of successful project implementation has progressively lifted the maximum processing rate of Concentrator 1 from the design estimate of 2455 t/h to above 3000 t/h. CITATION:Waters, T, Rice, A, Seppelt, J, Bubnich, J and Akerstrom, B, 2018. The evolution of the Cadia 40-foot SAG mill to treat the Cadia East orebody: a case study of incremental change leading to operational stability, in Proceedings 14th AusIMM Mill Operators&#39; Conference 2018, pp 217–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J. G. Bruwer

Paper written on project work carried out in partial fulfilment of B Eng Met Surface coatings persisting on zircon particles, after being leached in an acidic solution, are believed to be the cause of zircon misplacement during the electrostatic separation of heavy mineral beach sands. Electrostatic separation is employed to separate non-conductive zircon particles from more conductive rutile particles. Surface coatings on zircon particles are believed to render the non-conductive zircon particles more conductive, resulting in the contamination of the more conductive rutile stream with zircon particles. Resistivity measurements, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were performed to compare the surface characteristics of zircon particles found in the different product streams following electrostatic separation. XPS analysis showed that no significant difference exists in the outermost layer of the zircon particles found in the different streams. SEM analysis showed the existing surface coatings on zircon particles from different product streams to have similar chemical compositions. Resistivity measurements confirmed the results obtained from both the XPS and SEM analysis; no significant differences in the resitivities were observed. From the results obtained it suggests that surface coatings present on zircon particles are unlikely the primary cause of zircon misplacement. Zircon losses can possibly be a result of machine related aspects. Key words: XPS; SEM; resistivity measurements; electrostatic separation; heavy mineral sands.

Jan 1, 2007

By R. Pickering

The purpose of this paper is to explore the application of technology to stoping systems. Technology, because for the past 100 years the South African narrow reef mining industry has battled to control working costs in a labour-intensive industry. Stoping systems, because it is the stoping method and methodology which is at the heart of the mining system. Introduce a more efficient stoping system and the mining system will look after itself. The technology applied to stoping over the past 100 years can be categorized as follows: ?The introduction of pneumatic rockdrills early this century, the cumbersome rig mounted units being replaced by smaller, lighter hand-held units which were then made easier to use with the addition of an air leg ?Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s ?Hydraulic props as a support method arrived in the1960s ?Some people argue that tungsten carbide inserts were equally important. There have been a number of attempts to introduce different technologies into stoping, the most recent being trackless equipment. Where the stoping layout suits the technology it has been successful. There have been too many instances where a technology has been installed because it is fashionable. At the end of the day the outcome from change in the stoping systems has to be safer and more profitable mining systems. It is the contention of the author that change is only likely to be effective if it is supported by the introduction and application of appropriate technology.

Jan 1, 1999

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou&apos; measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman&apos; calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay&apos; are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou&apos; and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil&apos; calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult&apos;s law within the requirements

Jan 1, 1957

By P. O. Osifo, K. Premlall, X. Goso, R. H. Matjie, M. R. Mulaudzi, J. R. Bunt, K. Mphahlele

This study investigates the transformation of pyrolytic spent tyre-derived char and crumb rubber into high-performance activated carbon chars for industrial wastewater remediation. Utilising an in-house macro-thermogravimetric analysis system under an argon atmosphere, spent tyre-derived activated carbon char were synthesised via physical temperature activation and aqua regia demineralisation. Comprehensive characterisation using x-ray diffraction, Raman spectroscopy, and scanning electron microscopy, revealed a predominantly amorphous structure with nanoscale crystallites (~1 nm) and active surface functional groups. Proximate analysis confirmed that both crumb rubber and leached tyre crumb rubber with aqua regia derivatives achieved favourable compositions (ash ≈ 9.6%; fixed carbon ≈ 84%), comparable to commercial activated carbon (AC). At an optimal activation temperature of 850°C, the char of tyre crumb leached with aqua regia variant exhibited a significant surface area of 300 m²/g. Crucially, the tyre crumb char produced at 850°C variant developed a pore volume of 0.8 cm³/g—effectively doubling that of commercial activated carbon (0.4 cm³/g)—facilitating the sequestration of large organic molecules. In application tests using high-strength starch wastewater, char of tyre crumb leached with aqua regia and tyre crumb char, both produced at 850°C, achieved total organic carbon removal efficiencies of 60% and 50%, respectively, bridging the performance gap between waste-derived and commercial adsorbents. These findings validate waste tyres as a viable, low-cost precursor for industrial-grade adsorbents, offering a sustainable circular economy route for tyre valorisation and reduced industrial disposal costs. Future research will focus on kinetic modelling and the recovery of zinc from spent tyre-derived activated carbon char residues.

Mar 30, 2026

Arsenic (As) removal behavior from Changgoon mine tailings was investigated using Acidithiobacillus ferrooxidans (A. ferrooxidans) in well-controlled batch reactors by varying pulp density (0.5?4%, pH=1.8, temp=30oC), reaction initial pH (1.8?2.2, pulp density=0.5%, temp=30oC), and temperature (25?35oC, pulp density=0.5%, pH=1.8). The initial concentration of As in the mine tailings used for bioleaching tests was about 30000 ppm, and the size range of tailings used in this study was 63?74 µm. The reaction speed and initial cell concentration were fixed to 150 rpm and 107 cells/mL, respectively. To complement leaching experiments, pH, oxidation/reduction potential (ORP), and amount of ferrous/ferric ions in leachate were analyzed. Scanning electron microscopy and x-ray diffraction analyses were also conducted for the samples before and after leaching to see if any morphological and compositional changes in tailings took place during leaching process. The As leaching efficiency increased with decreasing pulp density, decreasing pH, and increasing temperature in the presence of A. ferrooxidans. Specifically, no significant change in As removal rate was observed when pulp density d 2% while the removal rate dramatically decreased at pulp density of 4%. Regarding pH effect, As removal rate was much more enhanced at lower pHs (i.e., 1.8 and 2.0) compared to pH 2.2. Increasing temperature was observed to tend to enhance As removal rate, showing about 20% enhanced leaching rate under 35oC compared to 25oC and 30oC at the elapsed time of 5 days. The results for As removal behavior at different conditions (i.e., pH, temperature, pulp density) were consistent with the change in pH, ORP, and ferric ion concentration in leachate, showing greater removal rate at the condition with lower pH, and higher ORP and ferric ion concentration in leachate. Furthermore, decreasing removal efficiency was likely in part due to the extent of the formation of by-product (i.e., jarosite) of ferric ions.

Feb 27, 2013

By Elzbieta Mielczarski, Jerzy A. Mielczarski

"It is well documented that xanthate adsorption on sulphide minerals is electrochemically controlled process. Under well controlled potential conditions the adsorption of xanthate takes place at different potential on each mineral, hence, each mineral component can be selectively separated from ore. This was demonstrated in the past for single mineral systems. In real flotation this concept never works out for two reasons: the potential of single mineral particle results from its interaction with solution as well as from galvanic contact with other particles present in the flotation pulp. Thus, the potential of a single particle results from complex surface reactions controlled by solution chemistry and the presence of other mineral particles that also interact with the solution. In flotation it is not possible to control mineral particle potential as it was demonstrated in voltametric studies of single mineral.In this study adsorption of xanthate on pyrite, galena and chalcopyrite has been investigated in the presence of those minerals. The second mineral was in solution: (i) without any physical contact with the first one, (ii) in direct contact (non-liberated grain or connected by wire), (iii) in collision type contact similar to that observed in real flotation.The adsorption of amyl xanthate on pyrite, galena and chalcopyrite was monitored by infrared external reflection technique directly on mineral surfaces. Type of the adsorbed species and their amount were concluded from the recorded reflection spectra. The presence of second mineral in solution without any physical contact does not influence adsorption. The minerals behave as if they were separated (at least during 30 min of the experiment). However, any type of galvanic contact between grains of two different minerals has tremendous consequence on the adsorption of collector on the both minerals. The detected changes are dramatic, from no adsorption to a few monolayer coverage formation.For example, pyrite that adsorbs amyl xanthate strongly in single mineral system in its galvanic contact with galena practically shows no adsorption of the collector in the same solution conditions. On contrary adsorption of xanthate on galena is tremendously enhanced during the galvanic contact with pyrite. The observed changes in the surface reactions are discussed and mechanisms of xanthate interactions in different galvanic contact are proposed."

Jan 1, 2003

By Zhou Junwu, Sun Chuanyao, Wang Fuli

"In this present paper, the authors introduce the artificial neural networks into the modeling of the industrial flotation process, integrating information technology, control theory and intelligent optimizing method to flotation technology. The new idea gives a new way to solve the difficulty in this field, and therefore brings the study on the automatic control of flotation process in China into a new start.The Radial Basis Function (RBF) network, featuring a quick learning speed, is one of the feedforward neural networks. It has attracted much attention from automatic control recently for its implementing the nonlinearity mapping through adjusting the parameters of the nonlinearity transfer function. One of the online adaptive learning algorithm—the nearest neighbor-clustering algorithm, which can automatically determine the number of hidden units, has been implemented in the MATLAB programming language in this paper, laying the foundation for the flotation models.The relation model between ore pulp characteristics and reagents consumption has been proposed using the RBF networks based on the industrial lead rougher flotation of lead & zinc ore, and the simulation has been conducted in the laboratory with the results matching the samples data very well. The Xilin Lead & Zinc Mine Flotation Process Intelligent Consultation System of Reagents Consumption, which suitable for industrial process, has been developed. The reagents consumption advised by this system would stabilize the flotation process, and increase the recoveries. It could be used for providing the technological consultation to flotation operators in site, and for training new operators."

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Froth structure and stability are known to play an important role in determining flotation recovery and selectivity. An industrial sampling campaign was performed to develop a clearer understanding of the effect of flotation variables on froth stability and the role played by the resulting stability on flotation performance.Froth stability was estimated as the fraction of bubbles bursting on the surface of the froth through image analysis and the solids loading on the bubbles at the top surface. The image processing was performed using the Smartfroth software on the top surface of the froth. The system gives measurements of bubble size distribution, average bubble size and froth velocity. The froth velocity was used to estimate the volume of bubbles overflowing the weir yielding to the fraction of air overflowing the cell. This measurement is the complement of the rate of bubble bursting on the top surface. Also samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. Then, the amount of solids and liquid per unit area in the bubble lamellae was estimated gravimetrically. Both measurements were used to establish stability criteria.It was generally found that high air flowrates resulted in a drop of froth stability showed by a drop in the fraction of air overflowing and a decrease in the solids loading and simultaneously produced low copper recoveries and low concentrate grades. Deep froths only allowed a small fraction of air to overflow and consequently produced low recoveries. An increase to high frother dosage did not result in an improved fraction of air overflowing, hence producing low recoveries. Likewise, low frother addition only allows low recoveries because the resulting unstable froth cannot support itself. Low aeration was found to be preferential as it allowed high particle loading, therefore high bubble stabilisation, and low gangue entrainment, resulting in the highest flotation performance."

Jan 1, 2003

By Leon Lorenzen, Charlene Gokhale

"In excess of 24 x 106 tons (Eskom, 1997) of coal-derived fly ash is produced annually in South Africa for the production of electric power. A large quantity of this ash is disposed of as a solid waste in landfills, thus posing a serious environmental problem. Due to the shortage of landfill sites, new ways of utilising fly ash are needed. Recently several authors have shown that various combustion fly ashes can be converted into zeolites to obtain industrial products with applicability in environmental management. Geopolymerisation has emerged during the last few years as a possible solution to some waste stabilisation and solidification problems. henolic compounds have been shown to be toxic to soil microorganisms at the parts-per-million level. Indeed several of the organic compounds classified by the U.S. Environmental Protection Agency as priority pollutants, are phenols. Immobilisation of phenols by adsorption on zeolites and encapsulation in a geopolymer appears to be a promising solution to this problem.This paper reports a technique for the production of a low-silica sodium zeolitic material from fly ash (zeolite NaP1), and its application for the stabilisation of phenols by adsorption and subsequent encapsulation in a geopolymer matrix. A commercial zeolite, clinoptilolite was also utilised as an adsorbent. Due to their uniform pore sizes and large surface areas, zeolitic materials are suitable for ion exchange and adsorption of certain organic substances. Adsorption data show that the commercial zeolite, clinoptilolite was an effective adsorbent for organics. Adsorption data showed that between 51.2 ppm and 74.3 ppm of chlorophenol or between 15.4 ppm and 32.5 ppm of phenol could be adsorbed. Physical encapsulation of the coated zeolite loaded with organic within a geopolymeric matrix increased the compressive strength of the matrix from 28.80 kN to 40.79 kN. Leaching data for the various geopolymer matrices with encapsulated and loaded zeolites show no organics being leached from the system at a detection level of 2ppm. According to the SABS these would have been acceptable organic concentrations within a waste water stream."

Jan 1, 2003

By Kang N. Zhong, Hui H. Luo, Yunan Phosphate Chemical Co., Yi H. Wei, Yao J. Li, Yu L. Wang

"The three kinds of phosphate ores (igneous, metasedimentary and sedimentary) found in China have great differences in flotation flowsheets and reagents suite because of their crystal structure and mineral composition. The igneous and metasedimentary apatites have good floatability with fatty acid as collector and waterglass, sodium hydroxide or sodium carbonate as conditioners. The sedimentary phosphate is very difficult to beneficiate by direct flotation because of their poor floatabilities and relatively high content of MgO and SiO2, even though the dolomite depressants are used sometimes.The differences in floatability of apatites in China are closely related to their differences in specific surface area. The amount of collector to float apatite increases with the specific surface area. Apatite with lower specific surface area showed good floatability at lower collector concentration. Apatite with a higher specific surface area needed a higher concentration of collector. The content of CO3 2- will affect the specific surface area of apatite by distortion of its crystal structure and consequently affect its floatability.Dolomite can be easily rejected from apatite in a weak acidic medium (pH=5), especially in phosphoric acid medium by reverse flotation. Quartz and siliceous gangue in sedimentary apatite can be removed by direct flotation using fatty acid or by reverse flotation using amine. Amine is not practically applied because sedimentary apatite in China is usually very fine and needs fine grinding, which always results in excessive, very fine, stable and non-flowable foam.Based on the floatability of phosphate ore in China, a two-stage flotation process, direct and reverse flotation (D+R), was developed to beneficiate sedimentary ore. For the Haikou phosphate ore containing 25.11% P2O5, 3.46% MgO and 16.5% SiO2, a concentrate containing 31.84% P2O5, 0.48% MgO and 14.8% SiO2 can be obtained through a continuous D+R test at a recovery of 89%."

Jan 1, 2003