Search Documents

By Peng Jiahong

With ultrasonics application during checking the large diameter cast-in-situ pile body, it is usualy applied the statistical method of probability and PSD. This paper presents a converse probabilistic-analytical method which can identify important anomalies, both strong and weak, during interfered situation. So the inhomogeneity in concrete pile may be ellectively distinguished. In order to ensure the capacity of bed rock support layer under large diameter pile, a test-in-situ is conducted to determine the compresive strength and shear force inserting rock of the support layer, so the compresive strength and modulus value of elasticity of bed rock tested will closely tally with the actual situation.

Jan 1, 1991

By Emilie S. Williams

The Doyon Mine?s Zone 1 (Altered Zone), found along the southern boundary of the mine, encompasses approximately 20% of the mining reserves. The mineralisation is found in a series of steeply dipping narrow veinlets, which are contained in an extremely weak host rock: a sericitic schist with RQD values ranging from 0 to 20. Longhole mining methods are used, with either longitudinal or transverse approaches, depending on the width of the ore zone. Dilution is of critical importance in the mining of this zone, particularly in longitudinal stopes, where dilution levels have averaged 55% since 2000. Major factors influencing dilution in this zone include the stope geometry and standup time. A two-phase approach has been developed to mine and backfill longitudinal stopes: the top of the stope is pastefilled after approximately half of the broken ore has been extracted; the remainder of the ore is extracted once the plug has cured; and the remaining void is filled. This method has been used in six stopes to date, resulting in an average dilution of 17%. This paper details the application of this technique and its effect on dilution.

Oct 1, 2004

Bitumninous and semianthracite coal reserves underlie about 1,400 square miles of Arkansas, less than 2.7 percent of the state's total area. These deposits, located near the western border, contain an estimated 2.2 billion tons, of which about half are recoverable. This represents less than one-tenth of one percent of the national reserves. Most of the commercial coal is mined from thin beds that are at least 14 inches thick. In some locations, however, the coal beds can be as much as eight feet thick. Lignite was mined in southern Arkansas before the Civil War. Current estimates indicate that the reserves may be as high as 9 billion tons, which could be used in the state's coal-fired electric generating plants; however, these deposits are not being mined at present. Because many coal operations in Arkansas are small and the demand for coal is unsteady, the industry employs fewer than 25 miners on a daily basis. Arkansas gained primacy when its regulatory program was conditionally approved November 21,1980, subject to the correction of four minor program deficiencies. The regulatory program was fully approved January 22, 1982. Authority of the state to administer its Abandoned Mine Land Reclamation Program was granted upon approval of the Arkansas Reclamation Plan on May 2, 1983. Arkansas was the first state to assume responsibility for abandoned mine land emergency projects when its Reclamation Plan was approved.

Jan 1, 1992

By Alberto Pacheco Pacheco

En el presente texto se analiza el fundamento de lógica fuzzy aplicada al control de molienda de minerales, la que nos permite simular el comportamiento humano en la operación molienda, con la que se plantea el algoritmo de control inteligente de molienda.

Sep 12, 2005

By L. M. Gould

"Syncrude Canada operates the largest oil sands crude oil production facility in the world and produces over 13% of Canada’s total oil requirements. To achieve this, Syncrude mines the oil sands in open pits, extracts the raw oil known as bitumen from the sand using water-based processes and upgrades it into sweet light crude oil by fluid coking, hydroprocessing, hydrotreating and reblending. The final product, Syncrude Sweet Blend (SSB), is sent by pipeline to three Edmonton area refineries and then to pipeline terminals which ship the SSB to refineries in Canada and the United States.As parts of the Mildred Lake base mine reached their economic life, they were replaced with new facilities at the Aurora Satellite mine. Aurora is situated on Oilsand Leases 10, 12 and 34, 35 km northeast of the Mildred Lake facility (Fig. 1).In 2000, the first hydrotransport low-energy extraction production train started up at Aurora. A second production train is scheduled for start-up in 2003. Open pit mining at Aurora occurs using two hydraulic shovels, two cable shovels, and trucks ranging from 320-ton to 380-ton payload capacities (Fig. 2).Once the oil sands is excavated, the trucks dump the ore into a crusher designed to break up the big lumps of oil sands and rock at peak rates of 11 000 t/hr. The ore is then transferred by conveyor to a surge pile and then to a mixing box which combines the oil sands with hot water. Following bitumen separation in the primary separation vessel, froth is delivered to Mildred Lake for processing via the intersite pipeline (Fig. 3).The goal of this paper is to illustrate how high precision shovel GPS (HPGPS) is being used at the Aurora mine to aid in mine planning. This can be accomplished by first describing the function of the mine planning department, describing the Aurora orebody, and finally explaining how the HPGPS system functions and how it is employed at Aurora.The short range mine planning department ensures a steady supply of ore is delivered to the plant at the desired grade in a sequenced and economical manner. This is done by creating a mine plan that consists of shovel dig locations that require the shovels to mine in a specified area at a specified elevation."

Jan 1, 2002

By D. Bessinger

The present paper provides a brief overview of the thermodynamics of titania rich slags, an outline of the Multi-Phase Equilibrium (MPE) package and its application to ilmenite smelting. Through assessment of published experimental data on various systems containing TiOx, it was found that despite considerable scatter in measured phase equilibria data for the binary Ti2O3-TiO2system,the behaviour of binary and higher order titania rich slags and oxide solid solutions phases could be represented by solution models in the MPE package. Results from the applications of the MPE model on the stability of solid phases and slag-refractory interactions will be presented and discussed. Parallels will be drawn between the predictions by the model and observations made during pilot plant tests. Key words: Thermodynamics, titania slags, ilmenite smelting, phase equilibria, refractory.

Jan 1, 2003

By Timothy C. Siegel

Accurate representation of the geotechnical resistance distribution is critical in evaluating the performance of piles and pile groups for design. A current practice is to infer the geotechnical resistance distribution based on measured changes in strain during conventional top load pile testing. Especially for drilled and bored piles, the residual load is typically assumed to be negligible both during testing and after the application of the structure load. A practical result is that the compressive structural load is anticipated to be opposed primarily by the shaft resistance with little or no mobilized toe resistance. The predicted top deflection is estimated as the combined elastic compression plus the movement necessary to mobilize shaft resistance. The development of residual load (and associated negative skin friction) results in a significantly different design condition. Negative skin friction tends to force the pile into the ground and develops residual load in the pile that contributes to the internal compressive load. Significant toe resistance can be mobilized in order to resist the combination of negative skin friction and the sustained compressive load. The pile movement becomes a function of the toe penetration required to mobilize sufficient resistance to reach a balance of forces. In an effort to study the development of residual load in augered cast-in place (ACIP) piles, the authors installed and monitored strain gages that were embedded in an 18-inch diameter ACIP pile at a site in southeast Georgia. The results of this study indicate that residual load develops over time and reaches a distribution that is consistent with the principles of the unified design of piles. It is concluded that residual load develops in ACIP piles (as well as all drilled and bored piles by the same mechanisms) and that the residual load should be considered in the interpretation of load tests and in the pile design, particularly in the estimation of the single pile and pile group settlement.

Jan 1, 2009

By Steven J. Page

Researchers have developed a model to describe airborne respirable dust (ARD) generation on surface coal mine drills. By measuring a few basic parameters and using a graph, a drill operator or engi­neer can estimate the relative severity of drill dust emissions as well as how much of a reduction in ARD can be obtained by changing any given parameter. Geometric parameters include: drill deck cross-sectional area, shroud leakage associated with the deck shroud as well as the operational parameters of bailing air­flow, and dust collector airflow. The rela­tionships yield predictive ARD values which fall in the range measured on oper­ating drills for collector/bailing air flow ratios greater than 2. Overexposure to airborne respirable crystalline silica dust can cause serious or fatal respiratory disease. Exposures of sur­face coal mine rock drillers to respirable crystalline silica are of particular concern. In a 1992 alert on silicosis in rock drillers, the National Institute for Occupational Safety and Health (NIOSH) reported on 23 cases of advanced silicosis (acute, acceler­ated, and chronic) ranging in ages from 25 to 60 with drilling tenures ranging between three and 20 years.1 Most of the cases involved drill operators in their 30?s and 40?s, indicating high silica exposure levels are associated with their occupation. A more recent lung x-ray surveillance study of a 664 volunteer population of surface coal miners showed that the prevalence of silicosis-like abnormalities was 9%.2 The two most significant factors associated with these abnormalities were increasing age and years of drilling experience.

Jan 1, 2008

By J. S. Harington

Our purpose is to record and to explain the widely changing numbers of the huge total of black workers on the gold mines of South Africa over the century from 1896 to 1996. These men were recruited from up to twenty territories, and their contributions are examined. The major areas providing labour over this long period have been Lesotho, the former Transkei within South Africa and Mozambique. From 1989 to 1996, for instance, these three areas accounted for over sixty per cent of the total labour force (tlf). Our principal Figure 1 shows the tlf fluctuating through time to reach a peak of 480 000 in 1988. Irregular falls are also documented with the most serious in 1995 to 180 000. Based on this graph we consider the political, economic, sociological and historical reasons behind these changing employment opportunities. These have included external world-scale events such as war or depression, as well as internal changes of national economy and policy. We show the importance for numbers employed of the discovery of gold in the Orange Free State in 1946, the influence generally of the ?Winds of Change? and the firm maintenance by the State of law and order. Varying gold production costs and profitability against high tax rates, allied with increasing wages and a lack of development capital, have led in the last decade to employment falling by fifty per cent, despite an actually higher value of gold output. Finally, this analysis considers the role of the migrant labour system as it affects, and is affected by, conditions in the gold mining industry, with special reference to its less than humane consequences in the numerically dominant territories of Lesotho and Transkei.

Jan 1, 2004

By Roberto Chambi

El presente texto describe las experiencias relacionadas al desarrollo e implantación del Sistema deTopografía para la mina subterránea de produccción polimetálica Raura. Para ello, se desarrolla la importancia de la topografía en el diseño y los proyectos mineros a través de un sistema de cálculo y dibujo topográfico. Los principales objetivos del sistema son: la gestión de la base de datos topográficos de la mina, la sustitución de las operaciones matemáticas “manuales” y la eliminación de sus errores inherentes, así como realizar automáticamente los dibujos de labores mineras a partir de la data recolectada y procesada, tanto en cálculos como en dibujo. De forma que se genera información procesada a los software especializados en geología y planificación.

May 25, 1998

By G. Laing

On scheduled commissioning and effective operation of a solvent extraction circuit relies on getting the design of both the core contact equipment and the peripheral plant right. Experience has shown that poor performance of new plants is frequently a result of ?utility? systems that do not match the requirements of the circuit, rather than the mass transfer equipment itself. Both the operator/owner and designer need to understand the ?complete requirements? for the circuit to get the balance of the design right. This paper reviews generic issues, frequently overlooked or altered during cost-cutting exercises, which have a significant impact on plant performance.

Jan 1, 2002

By R. L. Lawson

I?ve been asked to appraise the global role of coal and mining, and the best place I can think of to begin is with the World watch Institute, which purports to monitor all things global. Last fall the institute?s magazine, entitled World Watch, in a cover story called for a worldwide campaign to outlaw the use of coal before this century?s end. To my mind the article began the campaign. However, the institute had to admit that no such ban will be possible unless there is special help and heavy intervention?that is, novel policies and punitive taxes. I?ll quote directly from the magazine to underscore the point: ?without them the market will continue to deceive us into thinking coal is cheap, abundant and irreplaceable?.

Jan 1, 2001

By Douglas Batista Mazzinghy

O projeto Minas-Rio iniciou as suas operações no final de 2014 e se encontra na fase de ramp-up buscando a capacidade nominal. O circuito de cominuição inclui três prensas de rolos em circuito aberto com o objetivo de criar micro fissuras no minério e assim reduzir o consumo energético da etapa seguinte, o circuito de moagem de bolas. Este tipo de fluxograma, com prensa de rolos (circuito aberto) seguido de moagem de bolas (circuito fechado), é conhecido como circuito híbrido. A literatura apresenta este circuito híbrido como o de maior eficiência energética. A maior preocupação com relação as prensas de rolos aplicada aos minérios de ferro é a geração excessiva de finos que poderiam elevar o perda de material na etapa de deslamagem, anterior a etapa de concentração por flotação. Os resultados obtidos através de amostragem das prensas mostraram que não houve geração excessiva de finos. Neste trabalho são apresentados os resultados iniciais da operação das prensas de rolos.

Aug 16, 2017

By Y. Gordon

ABSTRACT A methodology based on a two-stage approach was developed for process technology selection. The first stage includes evaluation of available technologies, followed by shortlisting the best technologies based on mass and energy balance modelling, financial analysis, and risk analysis. The second stage involves detailed analysis using refined input data, mass and energy balance modelling, and capital and operating cost estimation, as well as a more detailed financial analysis. A case study covering the selection of ironmaking technologies for a company in the Russian Federation is presented to illustrate the critical elements of the methodology and the analysis process.

Jan 1, 2014

A large number of brittleness concepts have been used in very different studies in the literature. One of them is the B1brittleness concept. In this study, the objective is to criticize the B1 brittleness concept on rotary blast hole drills. The B1 brittleness concept, the ratio of uniaxial compressive strength (sc) to tensile strength (sT), are widely used as a rock brittleness concept in the literature (Inyangand Pitt, 1990; Verhoef, P.N.W. 1993; Neil, D.M. et al.1994;Becker, et al.1984; Evans and Pomeroy, 1966; Göktan, R.M.1992; Kahraman, S. 2001; Yamaguchi, U. 1970; Verhoef, P.N.W. et al.1996; Bilgin, 1982; Howarth and Rowlands,1987; Howarth, D.F. et al. 1986). So, it was used as a rock brittleness concept in this article. The value of the B1brittleness concept is equal to the tangent of ß angle in the following graph. It was seen that more meaningful relationships could be obtained with the B2 brittleness, the under ?Area?(= 1/2(scxsT) = B2) under the curve, instead of tangent ß, (=B1), of the curve.

Jan 1, 2003

By M. H. Farjadi, J. Azari

Cost analysis of chrome ore reduction is one of the important issues facing ferrochrome producers in today?s competitive environment. Much of this depends on quality and various ratios in the actual ore. The latter can have a direct bearing on electricity consumption and optimum efficiency of the furnaces. While the industry has been successful in reducing costs by designing larger and more efficient furnaces, the role of the optimum blend of ore has perhaps been given less emphasis. This paper will discuss the general specification and metallurgical characteristics of various chrome ores for producing high carbon ferrochromium on industrial scale. By analysing the results obtained from smelting, including chromium recovery and energy consumption, the determining parameters in total cost of ferrochromium i.e. chrome ore; reductant and energy consumption can be optimized. Our study is based on actual experiences obtained from Faryab Ferroalloy Plant over a period of approximately three years.

Jan 1, 2004

By Sean Gallagher, William S. Marras, Alan S. Litsky, Velimir Matkovic, Deborah Burr, John Landoll

Study Design. Survival analysis techniques were used to compare the fatigue failure responses of elderly motion segments to a middle-aged sample. Objectives. To compare fatigue life of a middle-aged sample of lumbosacral motion segments to a previously tested elderly cohort. An additional objective was to evaluate the influence of bone mineral content on cycles to failure. Summary of Background Data. A previous investiga¬tion evaluated fatigue failure responses of 36 elderly lumbosacral motion segments (average age, 81 ± 8 years) subjected to spinal loads estimated when lifting a 9-kg load in 3 torso flexion angles (0°, 22.5°, and 45°). Results demonstrated rapid fatigue failure with increased torso flexion; however, a key limitation of this study was the old age of the specimens. Methods. Each lumbosacral spine was dissected into 3 motion segments (L1-L2, L3-L4, and L5-S1). Motion segments within each spine were randomly assigned to a spinal loading condition corresponding to lifting 9 kg in 3 torso flexion angles (0°, 22.5°, or 45°). Motion segments were statically loaded and allowed to creep for 15 minutes, then cyclically loaded at 0.33 Hz. Fatigue life was taken as the number of cycles to failure (10 mm displacement after creep loading). Results. Compared with the older sample of spines, the middle-aged sample exhibited increased fatigue life (cycles to failure) in all the torso flexion conditions. Increased fatigue life of the middle-aged specimens was associated with the increased bone mineral content (BMC) in younger motion segments (mean ± SD, 30.7 11.1 g per motion segment vs. 27.8 ± 9.4 g). Increasing bone mineral content had a protective influence with each additional gram increasing survival times by approximately 12%. Conclusion. Younger motion segments survive considerably longer when exposed to similar spine loading conditions that simulate repetitive lifting in neutral and flexed torso postures, primarily associated with the increased bone mineral content possessed by younger motion segments. Cycles to failure of young specimens at 22.5° flexion were similar to that of older specimens at 0° flexion, and survivorship of young specimens at 45° flexion was similar to the older cohort at 22.5°. Key words: biomechanics, low back disorders, fatigue failure, age, motion segments, vertebral endplate fractures, torso flexion, lifting, bone mass. Low back disorders (LBDs) are a major cause of both short- and long-term occupational disability in the United States, and it is clear that workers in certain occupations are more susceptible to LBD.2-5 Specifically, epidemiologic studies have shown that jobs involving heavy physical demands such as construction,2,3 mining,2,4 and farming,5 engender increased risk of back pain. These occupations are thought to experience high LBD rates as a result of their extreme postural and manual lifting demands. Studies have shown that jobs involving significant lifting 6-9 and jobs that involve frequent bending10-12 are associated with increased LBD risk. Workers in the mining industry, in particular, often have to lift heavy materials in restricted workspaces that compel torso flexion. An understanding of the impact of repeated loading of the spine in flexion on fatigue failure of spinal tissues is thus a critical issue for our research agency, which is concerned with reducing the pain and disability associated with LBD in the mining industry. It is well accepted that loads experienced by the spine during manual lifting tasks are sufficient to cause fractures in the endplates of lumbar vertebrae, particularly on repeated loading. 13-15 Endplate fractures may not be painful in and of themselves 16; however, evidence suggests that the process of internal disc disruption and disc degeneration may be initiated via endplate fractures. 16,17 It has been shown that endplate damage will alter the distribution of stress in the disc, resulting in buckling of the lamellas of the internal anulus.17 Once this process has been initiated, repeated spine loading will cause additional disruption of the anular fibers, resulting in formation of significant fissures or tears. 11-21 If these tears occur near or extend close to the outer portions of the anulus, a wound healing process is initiated, which involves infiltration of mast cells, macrophages, and re¬lease of cytokines and growth factors. 21 The presence of these infiltrates has been strongly linked to discogenic low back pain. 21,22 Indeed, for patients experiencing chronic low back pain, the prevalence of internal disc disruption is at least 39%,19 which represents the most

Jan 1, 1966

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly, subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fume less fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

Changes in reductant and energy inputs which are required to adjust the slag composition in an ilmenite smelter to a higher or lower FeO content are calculated. The calculated changes are based on the assumption that solidification equilibrium with the freeze lining constrains the slag composition to follow a eutectic groove in the TiO2-FeO-TiO1.5phase diagram. Calculated equilibrium conditions along the eutectic groove are presented, and form the basis of the calculations. The inputs of energy and carbon need to deviate strongly from the steady-state values to adjust the slag composition. The inputs required at any given time depend on the desired rate of change of the slag composition, and the current slag composition. The steady-state relationship of a change in energy input of 5 kWh corresponding to a 1 kg change in carbon input also holds for the changed inputs during transient changes in FeO content. Keywords: Ilmenite smelting, freeze lining, solidification, eutectic

Jan 1, 2003