Search Documents

By William Van Impe

A most renewing and promissing soil displacement screw pile is called the O-pile. The O-screw pile is a soil displacement auger pile based on a screwing in - screwing out procedure. The displacement auger head consists of a discontinuously diameter - increasing steel tip, on top of which the continuous screw flange with variable pitch is mounted. The soil displacement is kinematically ensured by downwardly oriented slots mounted on the auger head at different well chosen locations on the flanges. This leads to a very efficient lower energy screwing-in sequence of the pile and consequently to a high penetration rate. A test loading program of instrumented O-piles has been carried out in order to evaluate the load settlement behaviour, the shaft and tip capacity of the O-pile, including its specific installation parameters.

Jan 1, 1996

By G. R. Robinson

Aggregate resources consist of sand and gravel, and crushed stone. They are large-tonnage, bulk-minable mineral commodities that are used in construction and industrial activities (Tepordei, 1999, 2001).Rates of aggregate production, use and mine permit approval in the mid-Atlantic region differ by population density. These rates are influenced by economic and human factors, such as demand, costs, land availability and community opposition. In some areas, the local availability of aggregate is limited. This is due to the lack of suitable local source materials for aggregate, the loss of potential high-quality aggregate resource production sites by preemptive land development and restrictive zoning (resource sterilization), and the difficulty of developing and permitting production sites for aggregate.

Jan 1, 2004

By A. Hotta

Reduction of CO2 emissions is the key driving force behind the development and implementation of new solutions for energy production. One solution is circulating fluidized bed (CFB) combustion technology combined with a high-efficiency once-through water-steam cycle. Foster Wheeler's CFB technology is today commercially available in capacities up to 800 MWe with ultra-supercritical steam parameters. Simultaneously, the Flexi-Burn® CFB technology is being developed to provide capability of flexible operation in air firing and oxy-combustion for carbon capture. CFB technology can offer an attractive solution for the reduction of CO2 emissions, owing to advantages such as fuel flexibility and low emissions that the air-fired CFB technology offers today. Pilot test facilities provide information about the performance of CFB oxy-combustion technology, and the acquired knowledge is being incorporated in boiler modelling and design tools. One of the European R&D initiatives on carbon capture and storage (CCS) is the Technological Centre for CO2 Capture and Transport, which is supported by the Spanish Government through the Fundación Ciudad de la Energía (CIUDEN). CIUDEN is a research and development institution created by the Spanish administration in 2006 and fully conceived for collaborative research in CO2 capture, transportation, and storage. The Technology Development Centre for CO2 Capture and Transport comprises two technologies on oxy-combustion: pulverized coal (PC) and circulating fluidized bed (CFB). This paper will focus on the design and main characteristics of the 30 megawatt-hour thermal capacity (MWth) oxy-CFB boiler. Foster Wheeler is the technology provider of the Flexi-Burn CFB unit, for which commissioning has been completed in the first quarter of 2011. The CFB unit design allows operation either under conven¬tional combustion with air or under oxy-fuel conditions. The size of this experimental boiler is sufficient to allow the scaling of the results to commercial units. In this way, multiple fuels and operating conditions can be tested economically. The results will validate the design of a future 330 MWe supercritical Oxy-Combustion Power Station (OXY-CFB-300 Compostilla Project) intended to demonstrate the CCS technology at commercial scale. The Compostilla OXY-CFB-300 Project is one of the six CCS demonstration projects funded under the European Energy Programme for Recovery (EEPR) of the EU. The project is based on a future 330 MWe CFB supercritical oxy-combustion plant, with CO2 storage in a deep geological formation. The first phase of the project, granted by the EEPR programme and led by the Spanish utility ENDESA, includes all studies and characterization work needed on CO2 capture, transport, and storage, as well the costs, financing, and regulatory and permitting required, prior to the final investment decision for the construction phase of the plant by the end of 2012.

Jan 1, 2012

By S. R. Borrowman

This investigation by the Bureau of Mines was undertaken to develop information on the extractive metallurgy of thorite ores because potential ore bodies of this mineral have been found recently in Colorado, Idaho, and Montana. Basic information on thorite ore treatment that would be useful in appraising the potential of these and other domestic thorium resources was developed. The work was done mainly on thorite ore containing 3.87 percent ThO2 from the Powderhorn district, Colo., and on a composite sample containing 0.52 percent ThO2 from the Wet Mountains district, Colo. Limited tests of d corroborative nature subsequently were made on a sample containing 2.30 percent ThO2 from the Lemhi Pass area on the Idaho-Montana border.

Jan 1, 1962

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion. In several cases, breaches occurred between the gravel pit and the river. Initial evaluation of several sites that experienced these breaches showed that impacts to the river system were complex and varied significantly from site to site. The impacts to the adjacent river system may be viewed as positive and negative. Several flood-plain-mining sites in Oregon located in areas of historic river flow reverted to active riverbeds. In many cases, state and federal fisheries biologists and university researchers saw the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries —Mined Land Reclamation Program (DOGAMI-MLR) is studying the effects to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound flood-plain decisions regarding mining.

Jan 1, 1999

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives involve several potential pitfalls. These are outlined in the present paper.It was found that coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate. For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition. Significant errors could be incurred if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen).For elemental analysis determination, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range. For representation of sulphur in coal, one should avoid doublecounting due to SO3 in the ash analysis.Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2.However, use of some of these species without considering the experimentally determined gross CV leads to significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy. Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than these four, provided the enthalpy is corrected.It is recommended that an ‘enthalpy correction value’ be incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to carbon being present in a form other than graphite should be used, as that would imply double-counting some effects."

Jan 1, 2015

By F Gervilla, J Laukkanen

The Kevitsa Ni-Cu-PGE deposit in northern Finland contains disseminated Ni-Cu-Fe sulfides, and platinum-group minerals (PGM). The 2.05 Ga-old ultramafic-mafic, funnel-shaped intrusion is intruded into a volcanosedimentary sequence. The major ore minerals are pentlandite, hexagonal pyrrhotite and troilite, chalcopyrite, cubanite and magnetite. Pyrrhotite and pentlandite are replaced by pyrite, millerite and heazelwoodite near the surface. Nickeline, maucherite and gersdorffite are locally abundant. A pilot feed sample of 575 t of the main orebody at Kevitsa had average grades 0.45 per cent Cu, 0.36 per cent Ni, 1.85 per cent S, 0.33 g/t Pt, 0.34 g/t Pd and 0.19 g/t Au, with 0.06 per cent Ni contained in silicates. Higher PGE contents (2 - 27 ppm) occur in a vertical N-S bearing fault zone. The PGM (n = 6022) mapped in specimens of four drill holes, consist of sperrylite 34.7 vol per cent, braggite and cooperite 18.5 vol per cent, geversite 17.2 vol per cent, moncheite 14.7 vol per cent, merenskyite 6.7 vol per cent, stibiopalladinite 4.3 vol per cent, sobolevskite 1.9 vol per cent, kotulskite 0.7 vol per cent, michenerite 0.6 vol per cent, keithconnite 0.3 vol per cent, rustenburgite 0.1 vol per cent, melonite, froodite, laurite together 0.1 vol per cent and only a few grains of sudburyite, irarsite, vysotskite, erlichmanite, hongishiite, Pt-Cu-alloys, three undefined Pd and Pt bismuthinides and antimonides and a Pd-Cu-bearing Pt-Ni-Fe sulfide. Most of the PGM, 62 per cent, are enclosed in silicates, 29 per cent are intergrown with sulfides, nine per cent are within sulfides. A portion of the PGE occurs in solid solution in sulfides and arsenides. Ni flotation yielded smelter-grade concentrates averaging 12.2 per cent nickel. The average sulfide Ni recovery is 78.8 per cent and total Ni recovery is 65.3 per cent. The average Pt is 10 g/t at 55 per cent recovery, Pd 7.7 g/t at 38 per cent recovery and Au 1.6 g/t at ten per cent recovery. Cu concentrates averaged 28.6 per cent Cu with an average recovery of 78 per cent and further 11 per cent in the nickel concentrate. The copper concentrate contains 4 g/t Au at 24 per cent recovery. The average Fe to MgO ratio 17.9 is well above the targeted minimum of 4.5. The pilot results show that the previously used TETA (triethylene tetramine) can be avoided and good quality, smelter-grade concentrates can be produced from the Kevitsa ore at economical levels of recovery by conventional flotation methods.

Jan 1, 2008

By John D. Sullivan, Alfred P. Towne

"In copper percolation-leaching plants the ore is usually crushed to a maximum size of about three-eighths inch. Ordinarily an ore is crushed as finely as feasible since the rate of extraction of copper is increased with decreasing size of particles owing to the greater surface exposed and. the shorter path required for solutions to come into contact with the minerals to be dissolved. However, greater degree of crushing also increases the amount of fines. When ores are charged into leaching vats the coarse and fine material tend to segregate, resulting in channeling of solutions and leaving the areas where fines predominate only partly leached. An improvement in the method of charging the ore into vats that would minimize the deleterious effects of the segregations of fines would increase the percentage extraction of copper.The Inspiration Consolidated Copper Co.4 recently installed classifiers to remove the primary slimes from the ore, before charging it into the leaching vats. This necessitates a separate agitation treatment for the slimes.Recent publications5 of the bureau have shown the advantages of agglomeration followed by trickle leaching to extract copper from concentrator tailings. It was shown that when equal parts of ore crushed to about 1/4-inch size and concentrator tailings were agglomerated with approximately 10 per cent of moisture, either in the form of water or leaching solution, and the mass was charred into a leaching vat the ore could be treated successfully by open-drainage trickle leaching. Even with 30 or 35 per cent of minus 200-mesh material present the ore could be leached, if it was not flooded with solution.The results obtained in agglomerating ores and slimes suggested the possible advantages to be gained by wetting the crushed ore for standard percolation-leaching plants before charging it into the vats. Wetting the ore whould make the fine material and slime cohere to the larger pieces of ore thus tend to prevent segregation when the ore is charged into the vats. The bureau, at its southwest Experiment Station and in cooperation with the Department of Mining and University of Arizona, Tucson Ariz., therefore made a study to work: out A way in which slimes could be handled in percolation leaching. The study showed that the method of charging ore into the leaching vats governed the distribution the fines and consequently the rate extraction of copper. The results of the study reported in this paper."

Feb 1, 1931

Ferruginous manganese deposits have been known at Ripon Hills since the late 1950s. The main group of deposits occur in an area 6 km by 5 km and these were extensively investigated by Longreach Metals N.L. during1971 and 1972 for possible commercial exploitation.Ripon Hills is a dissectcd fault plateau 350 m above sea level formed by the uplift of a block of gently dipping Proterozoic shales, cherts, and dolomite. The plateau consists of chert breccia which is underlain by massive dolomite. The shales which are ferruginous and manganiferous overlie the chert breccia but are now only preserved, in places, in the broad depression and valleys of the plateau.The ore deposits occur as supergene replacement of the shales and were investigated by geological mapping, grid percussion and diamond drilling, and bulk beneficiation testing. Iron and manganese oxides erraticallyreplace Shale accompanied by the leaching of other minerals. The ore is composed of fine grained pyrolusite intergrown with fine grained hematite and locally containing extensively altered bixbyite and braunite. Thegangue mineral is mainly kaolin.The average grade, using a 15 per cent Mn cutoff, was 19 4 per cent Mn and 25·9 per cent Fe for a combined drill-proven, indicated, and inferred tonnage of 56,000,000 tonnes. The average depth of this mineralization from the surface is 11 m. Using a cutoff grade of 20 per cent Mn the average grade was 24·6 per cent Mn and 23·0 per cent Fe for a combined tonnage of 12,000,000 tonnes to an average depth of 8 m.The substantial drop in reserves occurs because a high proportion of the mineralized material contains less than 20 per cent Mn.It was shown that whereas the lower grade ore, despite erratic fluctuations in grade, could be beneficiated to specification grade by crushing, screening, and conductivity ore sorting, the higher grade ore could be beneficiatedto specification grade by crushing and screening only. The utilization of the higher grade ore was considered to constitute a more viable operation.There is potential for high grade manganese ore to be discovered in the Ripon Hills area at the contact of chert breccia and underlying dolomite.

Jan 1, 1977

The main orebody of the Bodangora mine is a metalliferous quartz reef within a major fault plane in the strongly folded and faulted volcanic rocks of the Ordovician-Silurian Oakdale Formation. The similarity of the type of mineralization to that of other pyrometasomatic deposits in this area suggests that the mineralizing fluids originated in the nearby Wuuluman Granite.The associated Mitchell's Creek West or Dick's reef is discussed briefly.

Jan 1, 1970

By Joan T. May

Federal Bureau of Mines studies showed that some organic amine hydrochlorides can be used as dehydrating agents for producing anhydrous magnesium chloride from hydrates and brines. Laboratory-scale tests showed that double salts are formed by reacting 35 percent magnesium chloride brine or spray-dried magnesium chloride with pyridine hydrochloride. Heating decomposed these double salts to anhydrous magnesium chloride and recycle pyridine hydrochloride. Pyridine hydrochloride also chlorinated any magnesium oxide in the spray-dried magnesium chloride. The anhydrous magnesium chloride obtained by the method described contained less than 0.8 percent oxygen. More than 98 percent of the organic amine hydrochloride was recovered.

Jan 1, 1978

An efficient and portable mathematical model has been developed for simulating heat transfer in six-in-line slag-resistance-heating electric furnaces for smelting sulphide ores to produce base metals and platinum group metals. This model is a steady-state one relating furnace conditions and performances to various control and input parameters. Some transient effects occurring in electric furnaces are neglected for computation efficiency. This article describes the model development and modelling results. The present model is capable of predicting: (i) temperatures at various locations in a six-in-line furnace, such as slag bath, matte bath, solid charge, freeboard space, freeze lining, cooling water, and air gaps between solid material components, etc. (ii) freeze lining thickness, (iii)smelting rate, and (iv) heat loss rate, etc. A typical feature of the model is that it is easily portable to different application platforms and sufficiently efficient with execution times less than a few seconds. Therefore, it is possible to apply the model for online prediction and control of heat transfer and freeze lining thickness in industrial electric furnaces.

Jan 1, 2011

The risk associated with mining induced seismicity is one of the major threats to the safety and sustainability of deep underground mines. This paper describes techniques that allow site practitioners to efficiently control such risks in mines. The proposed approaches rely on ground support to strategically control seismic risk and re-entry time to tactically control this risk. The strategic approach is based on the detailed understanding of past seismicity to as certain the seismic hazard of individual sources throughout the mine. This approach also relies on assessing the potential damage that these sources can induce on nearby excavations using the excavation vulnerability potential (EVP) and rockburst damage potential (RDP) concepts proposed by Heal et al. (2006). It is then possible to investigate how to reduce the risk of experiencing damaging seismicity in mine drives by locally enhancing the ground support system. The tactical approach relies on a proposed methodology to estimate reliable re-entry times or exclusion periods based on the seismic decay following blasting. Some examples of how these techniques have been applied in Australian mines are given.

Jan 1, 2009

By C. M. Badeen, J. Paige, W. Evans, L. McCauley, A. Caddies, I. Alilovic, R. Turcotte, C. O. Lyogun, C. Bonner

Gear pumps are very commonly used for the pumping of AN-water based emulsion products for both handling and blast loading applications. The potential major hazardous problems likely to be encountered with these pumps are: (i) high probability of friction; (ii) possibility of product confinement in the area of the bushings; (iii); high bearing failure rate; (iv) pump running dry; (v) presence of foreign material; (vi) deadheading of pump; (vii) delamination of elastomer from steel gears. Of all these possible scenarios, the no-flow situations where the pump is running dry or deadheaded have always been recognized as the most serious ones.

Jan 1, 2015

The epithermal Au-Ag deposits of the Hauraki Goldfield have formed in the convergent plate margin setting of the Coromandel Volcanic Zone (CVZ). The deposits form as siliceous lodes in the upper parts of geothermal systems associated with andesitic and rhyolitic volcanism. Two types of low sulphidation epithermal mineralisation are recognised in these volcanic terranes. Vein deposits within the rhyolitic terrane in the east and south of the CVZ (Whitianga Province) are typified by Chalcedonic Silica-Adularia-Illite type mineralisation. The veins are hosted by both rhyolite-dacite volcanic rocks and the underlying andesitic basement. The mineralisation formed by episodic violent decompressional boiling of deeply circulating meteoric water, with some magmatic fluid contribution; this boiling was associated with hydraulic fracturing and hydrothermal eruptions in geothermal systems where the piezometric surface of the deep geothermal reservoir lay near-surface. Such episodic boiling provides chalcedonic veining, banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S gas from the fluid to cause major gold deposition.   Crystalline Quartz-Illite-(Adularia-Kaolinite) type mineralisation is widespread in the andesitic terrane forming the northern and western portions of the CVZ (Kuaotunu Province). There is a spatial association with weak mineralisation of the high sulphidation (Vuggy Silica-Alunite-Kaolinite-Illite) epithermal type and porphyry eu-Au type. Crystalline Quartz mineralisation is probably formed by the mixing of shallow acidic groundwaters with the ascending deep geothermal fluid in geothermal systems beneath andesitic stratovolcanoes. The piezometric surface to the deep geothermal reservoir in these systems is likely to lie at considerable depth, with acidic gases rising from the geothermal reservoir condensing within the overlying vadose zone. The cooling effect, oxidation and pH decrease accompanying mixing apparently overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of gold. A high level of base-metal sulphide precipitation also enhances gold deposition. Violent boiling of the mixing fluids may occur at local structural dilation sites, producing high grade "bonanza" gold mineralisation.

Jan 1, 1991

By Walker G. S

A study of the crystalline materials on or near the surface of freshly made or "green" superphosphate granules and mature, "set" superphosphate granules was undertaken using X-ray diffraction, X-ray mapping, scanning electron microscopy and electron probe micro analysis techniques. Calcium sulphate (CaSO4), calcium sulphate hemihydrate (CaSO4 1/2H20), and mono calcium phosphate monohydrate (Ca(H2PO4)2H2O), were the only crystalline species present in the "green" superphosphate.In the set superphosphate however, additional compounds were present, namely complex iron and aluminium phosphates Ca(Fe,AI) H(HPO4hF2)2H2O, (Fe)3(H3O)H8 (PO4)6H2O and calcium sulphate dihydrate (CaSO4.2H2O).The complex phosphates tied up the major part of the Fe and Al in the system and were concentrated on or near the surface of the granule. An intimate mixture of CaSO4.2H2O, and CaSO4, along with the above mentioned complex Fe-AI compounds, crystallize close to the surface of the granule and cause the setting of superphosphate that takes place during storage.

Jan 1, 1980

By A. W. Diedericks

Rosh Pinah Zinc Corporation (RPZC) identified implementing a Mineral Resource Management (MRM) programme at the mine as a strategic incentive. The purpose of the programme is to optimize the economic value of the RPZC mineral resource, over the total value chain of the mine, taking expected macro economic conditions into consideration as well. With Mineral Resource Management still being a relatively young drive in the mining industry, information on the concept is relatively scarce. RPZC had several successes and problems with implementing such a concept and also still has a way to go before a complete Minerals Resource Management approach is implemented at the mine and entrenched as a working culture. The purpose of this paper is to: ?define a systems approach to implementing a Mineral Resource Management programme at a base metal mine ?indicate the specific MRM approaches taken at RPZC ?indicate the expected advantages of implementing a MRM approach ?measure the actions already taken against the systematic MRM approach, and indicate the advantages already captured ?indicate the way forward taking lessons learned into consideration ?indicate proposals to implement the MRM approach in the macro mining environment in South Africa.

Jan 1, 2003

By S. Mostaghel, V. Hernandez, S. Ge

"The automotive industry is under a constant pressure to reduce the weight of vehicles in order to reduce emissions and improve fuel efficiency. As such, there is an ever-growing demand for high strength and high ductility steel grades to meet the need for lightweight automotive components. Over the past decade, the production and application of 2nd and 3rd generation Advanced High Strength Steels (AHSS) as a lightweight material in automobiles has gained significant popularity due to their exceptional mechanical properties. However, the production cost of these high manganese steel remains high, partially due to the need of large amounts of ferromanganese as alloying material in standard steelmaking processes.The current study introduces a new and cost-effective technology for the production of medium- and high-manganese steels, where self-fluxed micro-pellets of manganese ore will be used as the source of manganese that can be injected into the steel bath. Prior to injection, these pellets are subjected to a pre-reduction process using a mixture of H2 and CO gases, where partial metallization of iron and manganese will occur. Direct injection of the pre-reduced micro-pellets provides less volatilization/emission and higher recovery of manganese, and is capable of producing AHSS with 6–18 wt% Mn.INTRODUCTIONAutomakers are constantly searching for lighter, stronger and cheaper materials in an effort to create safer and more fuel efficient vehicles. The introduction of aluminum alloys and polymer composite materials for automotive applications has been carving into what is traditionally one of the most profitable markets of the iron and steel business. The steel industry responded with Advanced High Strength Steel (AHSS)—a family of manganese containing steels which exhibit exceptional strength and ductility."

Jan 1, 2016

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,500 tons of ore per day with an average gold grade of 0.34 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, a long-hole stope and cut-and-fill mining methods are used at the deposits which are divided into several mining zones. Cemented rock fill (CRF) is used as the backfill in the open stope. CRF design includes the aggregate design, the ratio of cement and fly ash design, and strengths for the long-hole stope and cut-and-fill. In the aggregate design, the particle size distribution is one of the most influential aggregate characteristics in determining how it will perform as a basic backfill material. Gradation helps determine durability, porosity, cement and water requirements, strength, and shrinkage. To cut the backfill cost, fly ash usually is added into the binder to replace some part of cement. However, adding fly ash can affect the strength of the backfill. The reasonable percentage of fly ash is also important for making a good and low cost backfill. Based on the different mining method, the different backfill with different strength is designed. A systematic quality control procedure for aggregate and backfill is followed. After four yeas application, CRF system in Leeville achieved very good results.

Jan 1, 2011

By J. Cayouette

In 1995, Louvicourt mine started one of the first paste backfill operations in Canada. From 500 000 t in 1995, the annual paste backfill tonnage produced reached 800 000 t in 1999. The maximum throughput of the surface plant (including binders) is 3500 tpd with a final density of 75% to 76% solids which gives a slump of 15 cm to 17 cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders in a mixture of 20% cement to 80% ferrous slag. In certain stopes, the binder ratio may vary from 2% to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5 Mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.

Jan 1, 2003