Search Documents

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By Albert Ladd Colby

A GLANCE through the Bibliography appended to this paper will show that the Transactions of this Institute contain what virtually contitutes a history of the development of the manu¬facture of steel rails in this country and abroad. It is, therefore, fitting that this paper, bringing one branch of this important subject down to date, should be here presented, and it is also appropriate to select this joint meeting of our Society with the Iron and Steel Institute to compare the specifications covering the rails produced in these two countries, and to propose a standard specification to govern the manufacture of American rails for export. During the last ten years the production of Bessemer steel rails in the United States and Great Britain has amounted to 32,128,720 gross tons. Nearly 19,000,000 tons have been rolled in the past five years. The next five years will see an even larger output, owing partly to the extension of railway projects in the Orient, in South and Central America, in Mexico, and in Australia and the other British Colonies. Of late years, the American rail-mills have so largely increased their daily output, that trade conditions have often made possible the delivery of American rails to foreign ports. The tenders submitted by American mills, however, have always been accompanied by requests for changes in the foreign specifications, chiefly in the reduction of the amount of testing required; and it has only been natural, especially at first, that the engineer, whose specification had always been accepted without question by British mills, should interpret American tenders 'as an evidence that an inferior rail would be furnished

Sep 1, 1906

By C. Machio

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process. Keywords Titanium?magnesium, mechanical alloying, PCA.

Jan 1, 2011

Were it simply a matter of extracting tin from the simple tin sulphide, the proposition would undoubtedly be simple enough. When, however, other valuable metallic sulphides are combined with the tin, and it is required to separate these intomarketable products, then the proposition becomes somewhat complex, and such is the case with the class of material of which I am about to write. The locality where it occurs is Howell, New South Wales, and chiefly at the Conrad Silver-Lead Mine. The tin sulphide occurs chemically alloyed with copper, iron and other metals associated with galena, pyrites, mispickel, blende and silver sulphide in varying proportions, and generally in a gangue of highly crystallised quartz.Several varieties of tin sulphides occur, and from the following analyses of three minerals, these being specimens specially selected free from foreign matters, it will be seen that the chemical composition is somewhat complex.

Jan 1, 1902

By Ronald F. Balazik

[This Bureau of Mines study is intended to identify and evaluate potential effects of impending large-scale U. S. rail line closings (abandonment) on domestic nonfuel mineral industries. This is the first nationwide study of rail abandonment impacts focused on nonfuel minerals. The analyses presented is based principally on a survey of 200 rail freight records and on statistical tests that correlated 2,000 points in the Bureau's Mines Industry Location System (MILS) with 700 prospective abandonments throughout the United States. The conclusions derived from the analysis can be useful in evaluating proposed national rail abandonment policy rind legislation regarding nonfuel miner it shipping. Among these conclusions are the following: (1) Certain mineral materials (especially fertilizers) are likely to account for a large percentage of the rail traffic affected by abandonment in the next few years, but the total tonnage- involved will be small; (2) abandonment will adversely affect some mineral shippers, particularly local smart haulers; and (3 abandonment could significance reduce the opportunity to develop new resources or reopen defunct mining facilities. Despite these problems, however, the data examined in this study do not indicate that current abandonment trends will cause widespread disruption 01 domestic nonfuel mineral shipping.]

Jan 1, 1980

By J. D. Steenkamp

Southern Africa has a history rich in the pyrometallurgical processing of ores. Two of the alloys produced are high-carbon ferromanganese (74?83 per cent Mn) and silicomanganese (59?67 per cent Mn and 14?31 per cent Si). The largest land-based manganese ore deposit in the world is based in the Northern Cape Province of South Africa. In 2010, 6.3 Mt of ore from the deposit was exported, mainly to China, Norway, Japan, and India, and an estimated 1.1 Mt beneficiated locally to produce manganese ferroalloys. In southern Africa the producers of manganese ferroalloys are Metalloys and Assmang, and of silicomanganese Transalloys, Mogale Alloys, and Match Corporation. Submerged arc furnace technology is utilized in the production of high-carbon ferromanganese (HCFeMn) and silicomanganese, applying the discard slag practice in both instances. The carbon content of HCFeMn is reduced using converter technology and that of SiMn using the Perrin process. Ninety per cent of the world?s manganese ferroalloys production is consumed by the steel industry. The consumption (and production) of manganese ferroalloys therefore closely follows worldwide steel production. From 2001 to 2010, the doubling of the worldwide production of manganese ferroalloys can be attributed to an increase in production capacity in Asia and Oceania, with the largest increase in the production of SiMn. Manganese ferroalloys produced in Asia and Oceania are mainly for the local market, with North America, Europe, Russia, and Turkey the major markets for alloys from southern Africa. The major challenges faced by the southern African manganese ferroalloy producers are increasing electricity tariffs and productivity of labour, which require a concerted effort by all parties involved to achieve a satisfactory solution. Keywords manganese ferroalloys, ferromanganese, silicomanganese, southern Africa, South Africa, manganese ore, high-carbon ferromanganese, refined ferromanganese, refined silicomanganese.

Aug 1, 2013

Strategic Branding ? In 2006 Explore for More was created ? By industry, for industry ? Cohesive approach to career attraction ? Defines industry and employers of choice Career Kits ? Positive impression of mining: ? before seeing the brochure 31% ? after seeing the brochure 83% ? Likely to consider a career in mining: ? before seeing the brochure 12% ? after seeing the brochure 23% MARS ? Mining Attraction, Recruitment, and Retention Strategy (2007-2010) ? Attract, recruit and retain a skilled workforce ? Increase participation of under-represented groups ? Dispel myths and misconceptions of the mining industry ? Inform and educate Canadians of career opportunities ? Promote and build upon industry best practices in workforce planning

May 1, 2009

By K. Y. C. Chung

A case study on foundation engineering through organic soils is presented. Located along the west shore of the Hudson River, site soils consist of random brick fill over a thick layer of peat and organic silts or clays. The organic layer is underlain by medium dense to dense sand with varying amounts of silt. Strong artesian pressures were measured in the sand. A pile foundation system was selected to support all structures. To avoid periodic flooding, new fill must be placed on the existing fill. Large total and differential settlements will occur due to consolidation and secondary compression of the organic soils. This settlement will reduce the allowable pile capacity due to the large negative skin friction in the organic layer; and will necessitate long-term maintenance of the final grade elevation. Pile load tests were performed to determine the allowable compression and uplift capacities, long-term capacities and pile driving criteria.

Jan 1, 2010

By Keith A. Heasley, Timotlly M. Barton

Historically, the surface subsidence over underground coal mines has been predicted using empirical profile or influence functions which have little or no connection to the actual mechanics of the subsidence- Without a mechanistic basis, establishing the exact site-specific parameters to use in these empirical methods has been problematic. A practical subsidence predictive method based on mechanics has the appealing capability of allowing the determination of site-specific parameters from fundamental properties of the overburden with minimal field calibration work. This paper presents a case study where a mechanics-based, boundary-element program is used to calculate the surface subsidence associated with several panels of a Northern Appalachian longwall coal mine. The program used in this case study is called LAMODEL, and it incorporates a frictionless, laminated overburden into a general purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin seam or vein type deposits. In this paper. the program is used to calculate both the underground convergence and the resulting surface subsidence at three longwalls. The subsidence results from the model are compared with field measurements and analyzed The results from the case study in this paper demonstrate that the laminated model with calibrated properties can easily provide fairly accurate subsidence predictions and is fairly flexible for fitting measured subsidence. However, additional subsidence predictive case studies are recommended in order to ultimately evaluate the potential of the laminated overburden model for practical subsidence prediction

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

Rio Tinto has embarked on a journey to use automation to improve the performance of its surface mines. The driver for automation is to improve the accuracy and consistency of mining processes and less to do with cost savings through labour reduction. A key task in most surface mines is blasthole drilling. The degree to how well this is done cascades through the downstream mining process. It impacts scheduling, excavation, slope stability, material handling, beneficiation and final product blending. Improved blasthole drilling was identified as an objective that has a significant business case in most of Rio Tinto's surface mines. This paper describes Rio Tinto's drill enhancement project that has developed a robust system for automating most of the functions on a Terex SKSS16 drill rig. Automated drilling is currently being used in production at the West Angelas iron ore mine in the Pilbara region of Western Australia. A description of the essential elements of the drill automation system is given together with an overview of how automated drilling is performed remotely from the mine office. A review of some of the benefits of the enhanced drill system is given together with the future plans to extend the functionality of the automated drill and the expected benefits.

May 1, 2010

The estimation of the spatial variation of the b-value of the Gutenberg- Richter relationship is important for both the general interpretation of the mechanism of rock mass response and seismic hazard assessment. The interpretation of b-value as a parameter of rock mass response is discussed in this paper. The methods applied to evaluate the spatial variation of b-value and the algorithm for obtaining the magnitude of completeness and b-value for subsets of data are presented with some verification analyses. The algorithms presented enable the automation of a spatial evaluation of b-value.

Jan 1, 2014

By Edmund J. Cardoza

WELCOME TO THE DEEP FOUNDATIONS INSTITUTE 26TH ANNUAL CONFERENCE AND WELCOME ESPECIALLY TO THIS SEMINAR ON NON-DESTRUCTIVE TESTING OF DRILLED SHAFTS, PRESENTED BY MEMBERS OF THE DFI DRILLED SHAFT COMMITTEE. MY NAME IS ED CARDOZA; I AM A VICE PRESIDENT WITH THE MILLGARD CORPORATION, A DRILLED SHAFT CONSTRUCTOR FOCUSING PRIMARLY IN THE EASTERN HALF OF THE UNITED STATES.

Jan 1, 2001

By O. Konovalov, M. Zhuravkov

In report the results of performance of research works on building up of the connected geoecological and geomechanical monitoring system for modelling and study of a state of mining massif in a region with large-scale underground mining works are discussed. The connected geoecological monitoring requires radical change of methodology of carried out works. To carry out modelling and researches it is impossible without construction of the integrated connected information model of region. Basis of construction of information systems and databases for all sections of Earth Sciences is the set of the approaches, among which, for example, methods of remote sounding, GIS- and GPS-technology etc. Computer technologies are basis on the "supercomputer" technology. The results of performance of some researches for regions of excavation of deposits of potash salts in Russia and Belarus are presented.

Jan 1, 2005

By I F. Bell, K P. Hammerschmid

Well planned and executed environmental management plans can reduce life-of-mine operating costs and the need to deal with major environmental issues at the time of mine closure. With proper planning during the exploration, feasibility and execution phases of a project, final closure costs can be reduced. The reduction of closure costs should be considered during exploration and initial feasibility studies and when process facilities, waste rock dumps and tailings impoundments are designed. During the mining of the resource, closure cost reduction will depend on effective and efficient environmental management plans for ongoing land clearance, segregation of mine waste materials, management of mine site water and workshop wastewaters, and the establishment of progressive rehabilitation strategies. These issues are the responsibility of planning, production, technical support and maintenance personnel at an operating site. The successful implementation of environmental plans will ensure that all impacts are reduced and that closure issues with major cost implications are addressed prior to closure of the mine.

Jan 1, 1995

By John C. Machisak

INJURY experience and employment data for the nonmetal mining industry in the United States are presented for the calendar year 1958. Statistical tables 6 to 12 give detailed information on injuries and employment at nonmetal mines. Data for nonmetal mines are presented separately from those for nonmetal mills, tables 23 29. The Bureau is authorized to send questionnaires to the nonmetal industry for their voluntary submission on of injury and employment experience at their operations. As this information contributes to the promotion of safety in the nonmetal mining industry, every effort has been made to make these questionnaires as complete as possible.

Jan 1, 1962

By C E. J de Ronde, I C. Wright

Oceanic subduction-related volcanic frontal arcs extend over 20 000 km within the western Pacific basin and over 21 500 km worldwide, yet they remain largely unexplored with respect to active seafloor mineralization. Systematic exploration of 26 major submarine volcanoes along ~840 km of the Kermadec arc northeast of New Zealand has documented ten (39 per cent) as being hydrothermally active. This frequency of venting is comparable to that on slow-to-moderate rate spreading mid-ocean ridges, which comprise ~80 per cent of the 60 000 km-long global system of spreading centers. The chemistry of fluids discharged from the Kermadec arc volcanoes is moderated by magmatic components in both the gaseous (CO2 + SO2-H2S) and liquid (Fe) phases at very high concentration.The high frequency of venting coupled with chemically rich discharge discovered during this first systematic survey of any arc system forecasts submarine arcs as being important sources of chemicals to the oceans and as potentially lucrative exploration sites for seafloor mineralization. The exploration protocols developed during these surveys include bathymetric mapping of mostly unknown volcanic edifices, followed by detailed water column profiling and sampling to detect and characterize volcanic fluid emission signatures. These procedures are being refined as the survey progresses, both for efficiency and as direct seafloor observations become available for predictive application of water column plume information to guide seafloor mineral exploration.

Jan 1, 2002

Conventional hand drawn isopach maps of the cover of the Bulli Seam are too eomplex for use in the delineation of large domains of similar cover. Isopach maps prepared from trend surfaces fitted to the cover data are much simpler in form and so provide a convenient method of delineating broad domains of similar cover.

Jan 1, 1968

By K. H. Coats, M. H. Terhune

Analysis and example applications have been performed to compare the accuracy and computing speed of alternating-direction explicit and implicit procedures (ADEP and ADIP) in numerical solution of reservoir fluid flow problems. ADIP yields significantly greater accuracy and requires about 60 per cent more computing time than ADEP, not 300 or 500 per cent more as reported elsewhere. l,2 INTRODUCTION Several recent papers 1-3 discuss an alternating-direction explicit difference approximation (ADEP) to the diffusion equation. Example applications of ADEP and ADIP4 were reported to support conclusions that ADEP is comparable in accuracy to ADIP and requires one-fifth to one-third the computing time of ADIP. Applications of ADEP in calculation of two-phase flow in reservoirs was also proposed. 3 This study was performed to compare further the relative merits of ADEP and ADIP in simulation of two-dimensional flow of one and two fluid phases in reservoirs. Since two-phase flow equations are often essentially elliptic rather than parabolic, the efficiency of ADEP in solving the elliptic equation was also examined.

Jan 1, 1967

By R. H. Seraphim

"Western Mines Limited produces gold, silver, copper, lead and zinc from a number of Paleozoic volcanogenic deposits near Buttle Lake on Vancouver Island. The deposits were emplaced along a series of submarine linear volcanic ridges that extended for at least 6,000 metres in a northwesterly direction.Rock types mapped include: andesitic, dacitic and rhyolitic flow s and volcanic breccias; detrital breccias, tuffs and hematitic silts; black and green cherts; and a variety of dykes and sills, including quartz porphyry and diorite. Orebodies are associated invariably, and in places intimately, with quartzsericite schist and rhyolitic rocks. The ore is complex, varying in mineralogy and tenor both within each deposit and from one deposit to another.Recent studies have increased our knowledge of the structure and left no doubt that the orebodies were deposited both within the throats of the linear vents and on paleoslopes adjacent to these vents.IntroductionWestern Mines Limited operates an 850-tonne-per-day mine, located 85 km south of Campbell River, B.C. The mine is at approximately 400 metres elevation, near the south end of Buttle Lake on Vancouver Island (Fig . I). It has operated since early 1967 and produced 3,650,000 tonnes with an average grade of 1.9 g (0.06 oz) gold, 93 g (3.0 oz) silver, 1.6 per cent copper, 1.0 per cent lead and 7.5 per cent zinc per tonne by the end of 1978. Current reserves are 1,157,000 tonnes of 2.7 g (0.09 oz) gold, 117 g (3 .8 oz) silver , 1.2 per cent copper, 1.2 per cent lead and 8.0 percent zinc per tonne (December 31, 1978).Ore from one zone, known as Myra High-Grade, is mined and milled separately because of its grade. Ore milled prior to December 31,1978, plus reserves, 180,715 tonnes of6.6 g (0.21 oz) gold, 554.5 g (17 .7 oz) silver, 0 .8 per cent copper, 3.2 per cent lead and 10.6 per cent zinc are included in the figures listed in the preceding paragraphs."

Jan 1, 1980